BEJC330ICellular/PCS GSM Phone with WLAN and Bluetooth

0+'M9WIV+YMHI 7SQISJXLIGSRXIRXWMRXLMW QERYEPQE]HMJJIVJVSQ]SYVTLSRI HITIRHMRKSRXLIWSJX[EVISJXLI TLSRISV]SYVWIVZMGITVSZMHIV 8LMWLERHWIXMWRSXVIGSQQIRHIHJSV FPMRHHMWEFMPMX]TIVWSRHYIXSXSYGL WGVIIROI]TEH Part 15.21 statement " Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. “ Part 15.105 statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device is not intended for sale in the USA.  +IXXMRKXSORS[]SYVTLSRI 4S[IV0SGOOI] d0SRKTVIWWJSVTS[IVSRSJJ d7LSVXTVIWWXSXYVRSRSJJXLIWGVIIR 'EPPOI] d(MEPWETLSRI RYQFIVERH ERW[IVW MRGSQMRK GEPPW )RHOI] 1YPXMXEWOMRKOI] 7MHIOI]W d;LIRXLIWGVIIRMWEX XLI,SQIWGVIIR 6MRKXSRIERHOI]XSRI ZSPYQI d(YVMRKEGEPP )EVTMIGIZSPYQI ,ERHWJVIISV7XIVISIEVTLSRI GSRRIGXSV 1MGVS7(QIQSV]GEVH WSGOIX 'EQIVEOI] 'LEVKIV97& GEFPI 0+'-`9WIV+YMHI  'LERKIXLI XI\XMRTYXQSHI GETMXEPWQEPP %PTLERYQIVMGOI]W 7TEGIOI] 9WIXSIRXIVEWTEGI[LIRIHMXMRK 'PIEVOI] d'PIEVWEGLEVEGXIVIEGLXMQIMXMW TVIWWIH,SPHXLIOI]HS[RXS GPIEVEPPMRTYX )RXIVOI] 7]QFSPOI] d)RXIVWW]QFSPMGGLEVEGXIV 3TIRZMI[ ;%62-2+4PEGMRKELIEZ]SFNIGXSRXLITLSRISVWMXXMRKSRMX [LMPIMXMWMR]SYVTSGOIXGERHEQEKIXLITLSRItW0'(ERHXSYGLWGVIIR JYRGXMSREPMX] 717 7SGMEP2IX[SVO -RXIVRIX*YPP &VS[WMRK 4YWL)QEMP -RWXERX 1IWWIRKIV  &EXXIV] 7-1GEVHWSGOIX 'EQIVEPIRW &EXXIV]GSZIV 0+'-`9WIV+YMHI  -RWXEPPMRKXLI7-1ERHFEXXIV] 6IQSZIXLIFEXXIV]GSZIV 7PMHIXLIFEXXIV]GSZIVXS[EVHWXLI FSXXSQSJXLITLSRIERHE[E] JVSQMX -RWXEPPXLI7-1GEVH 7PMHIXLI7-1GEVHMRXSXLI7-1 GEVHLSPHIVQEOMRKWYVIXLEXXLI KSPHGSRXEGXEVIESRXLIGEVHMW JEGMRKHS[R[EVHW4PIEWIQEOI WYVIXLIFEXXIV]MWVIQSZIHJVSQ XLITLSRIFIJSVIMRWXEPPMRKXLI 7-1GEVH8SVIQSZIXLI7-1GEVH TYPPMXKIRXP]SYX[EVHW ;%62-2+(SRSXYWI]SYV RKIVREMPXSVIQSZIXLIFEXXIV] ;%62-2+(SRSXVIQSZI XLIFEXXIV][LIRXLITLSRIMW W[MXGLIHSREWXLMWQE]HEQEKI XLITLSRI -RWXEPPXLIFEXXIV] -RWIVXXLIXSTSJXLIFEXXIV] MRXSXLIXSTIHKISJXLIFEXXIV] GSQTEVXQIRXJMVWX )RWYVIXLEXXLIFEXXIV]GSRXEGXW EPMKR[MXLXLITLSRItWXIVQMREPW 4VIWWXLIFSXXSQSJXLIFEXXIV] YRXMPHS[RMXGPMGOWMRXSTPEGI  'LEVKMRK]SYVTLSRI 6IQSZIXLIGLEVKIVWSGOIXGSZIVSR XLIWMHISJ]SYV0+'M'SRRIGX XLI8VEZIP%HETXIV 'LEVKIV ERHXLI MRGPYHIH97&GEFPI'SRRIGXXLI97& GEFPIMRXSXLITLSRIERHTPYKMXMRXS ETS[IVWSGOIX=SYV0+'MQYWX FIGLEVKIHYRXMPXLIq&EXXIV]JYPPq QIWWEKIETTIEVWSRXLIWGVIIR 238)8LIFEXXIV]QYWXFIJYPP] GLEVKIHMRMXMEPP]XSMQTVSZIFEXXIV] PMJIXMQI(MWVIKEVHXLIJMVWXq&EXXIV] JYPPrQIWWEKIERHOIITXLITLSRISR GLEVKISZIVRMKLX 0+'-`9WIV+YMHI  1IQSV]GEVH -RWXEPPMRKEQIQSV]GEVH =SYGERI\TERHXLIQIQSV]WTEGI SR]SYVTLSRIF]YWMRKE1MGVS7( QIQSV]GEVH 238)%QIQSV]GEVHMWERSTXMSREP EGGIWWSV] 3TIRXLIQIQSV]GEVHWPSXGSZIV SRXLIPIJXLERHIHKISJXLI TLSRI 7PMHIXLIQIQSV]GEVHMRXSXLI WPSXYRXMPMXGPMGOWMRXSTPEGI1EOI WYVIXLIKSPHGSRXEGXEVIEMWJEGMRK HS[R[EVHW *SVQEXXMRKXLIQIQSV]GEVH =SYVQIQSV]GEVHQE]EPVIEH]FI JSVQEXXIH-JMXMWRtX]SY[MPPRIIHXS JSVQEXMXFIJSVI]SYGERWXEVXXSYWIMX *VSQXLI,SQIWGVIIRWIPIGX  XLIR4LSRIWIXXMRKWMR7)88-2+7 XEF 8SYGL 1IQSV]MRJSXLIRGLSSWI )\XIVREPQIQSV] 8SYGL *SVQEXERHXLIRGSRJMVQ ]SYVGLSMGI )RXIVXLITEWW[SVHMJSRIMWWIX =SYVGEVH[MPPXLIRFIJSVQEXXIH ERHVIEH]XSYWI 238)-JXLIVIMWI\MWXMRKGSRXIRX SR]SYVQIQSV]GEVHXLIJSPHIV WXVYGXYVIQE]FIHMJJIVIRXEJXIV JSVQEXXMRKWMRGIEPPJMPIW[SYPHLEZI FIIRHIPIXIH  9WMRK]SYVXSYGLWGVIIR 8SYGLWGVIIRXMTW 8SWIPIGXERMXIQXSYGLXLIGIRXVId SJXLIMGSR (SRSXTVIWWXSSLEVH8LId XSYGLWGVIIRMWWIRWMXMZIIRSYKLXS TMGOYTEPMKLXJMVQXSYGL 9WIXLIXMTSJ]SYVJMRKIVXSXSYGLd XLISTXMSR]SYVIUYMVI&IGEVIJYP RSXXSXSYGLER]SXLIVOI]W ;LIRIZIV]SYV0+'MMWRSXMRd YWIMX[MPPVIXYVRXSXLIPSGOWGVIIR 'SRXVSPXLIXSYGLWGVIIR 8LIGSRXVSPWSRXLI0+'M XSYGLWGVIIRGLERKIH]REQMGEPP] HITIRHMRKSRXLIXEWO]SYEVI GEVV]MRKSYX 3TIRMRK%TTPMGEXMSRW 8SSTIRER]ETTPMGEXMSRWMQTP]XSYGL MXWMGSR 7GVSPPMRK (VEKJVSQWMHIXSWMHIXSWGVSPP 3RWSQIWGVIIRWWYGLEWXLI6IGIRX ,MWXSV]]SYGEREPWSWGVSPPYTSV HS[R 0+'-`9WIV+YMHI  =SYGERHVEKERHGPMGO[LEX]SYRIIHVMKLXE[E]MREPPLSQIWGVIIRX]TIW ;MHKIXLSQI WGVIIR ;LIR]SYXSYGL SRXLI FSXXSQVMKLXSJ XLIWGVIIRXLI QSFMPI[MHKIX TERIPETTIEVW ;LIR]SYWIPIGX [MHKIXERH HVEKKMRKMXSRXS XLIWGVIIRXLI [MHKIX[MPPETTIEVSRXLILSQIWGVIIR MRXLIWTSX[LIVIMX[EWHVSTTIH %GXMZI 7TIIHHMEPLSQI WGVIIR =SYGERGEPPWIRH EQIWWEKISV IHMXXLIGSRXEGX HMVIGXP]MRXLMW LSQIWGVIIR ;LIR]SYXSYGL XL…

Text truncated - open the document above for the full version.

Date: January 24, 2011 Federa l Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 RE: Request of Confidentiality for FCC ID: BEJ C330I Equip ment Class: DTS: Digital Transmission System To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: PERMANENT AND SHORT-TERM CONFIDENTIAL LIST Exhibit Description 1 Block Diagram 2 Operational Descriptions PERMANENT 3 Schematics 4 External Photos 5 Internal Photos 6 Test-Setup Photos SHORT-TERM 7 User’s Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, Jae Cheon(J.C.) Lee General Manager LG Electronics USA LG Electronics Inc. LGE LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, NJ 07632

External photos of EUT Front view of EUT Rear view of EUT Top view of EUT Bottom view of EUT Side view of EUT Slide view of EUT

Model No: LG-C330i FCC ID : BEJC330I S/N : Made in Korea LG Electronics Inc. LGE

Internal photos of EUT Top view of main board Bottom view of main board Top view of LCD module Bottom view of LCD module Top view of Sub PCB Bottom view of Sub PCB GSM Antenna

Report File No. : F690501/RF-SAR001915-A1 Date of Issue : 2011-01-27 Page : 2 / 124 Contents 1. General Information 1.1 Testing Laboratory........................................................................................... 3 1.2 Details of Applicant.......................................................................................... 3 1.3 Version of Report............................................................................................. 3 1.4 Description of EUT(s)....................................................................................... 3 1.5 Test Environment............................................................................................. 4 1.6 Operation description........................................................................................ 4 1.7 Evaluation procedures....................................................................................... 5 1.8 The SAR Measurement System............................................................................ 6 1.9 System Components.......................................................................................... 8 1.10 SAR System Verification.................................................................................... 9 1.11 Tissue Simulant Fluid for the Frequency Band.......................................................... 11 1.12 Test Standards and Limits.................................................................................. 12 2. Instruments List.................................................................................... 14 3. Summary of Results................................................................................ 15 APPENDIX A. DASY4 SAR Report B. Uncertainty Analysis C. Calibration certificate Report File No. : F690501/RF-SAR001915-A1 Date of Issue : 2011-01-27 Page : 3 / 124 1. General Information 1.1 Testing Laboratory SGS Testing Korea Co., Ltd. Wireless Div. 2FL, 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea 435-040 Telephone : +82 +31 428 5700 FAX : +82 +31 427 2371 Homepage : www.kr.sgs.com/ee 1.2 Details of Manufacturer Manufacturer : LG Electronics Inc. Address : 60-39, Gasan-dong, Gumchon-gu, Seoul, 153-023, Korea Contact Person : Hyeon Kyun Kim Phone No. : 82-2-2033-1113 1.3 Version of Report Version Number Date Revision 00 2011-01-25 Initial issue 01 2011-01-27 Revision 01 1.4 Description of EUT(s) EUT Type : Cellular/PCS GSM with Bluetooth & WLAN Model : LG-C330i (Additional model name : C330i) Serial Number : 011KPKN899349 Mode of Operation : GSM850, PCS1900, WLAN, Bluetooth Duty Cycle : 8(GSM), 8(GPRS 1Tx Slot), 4(GPRS 2Tx Slot), 2.67(GPRS 3Tx Slot), 2(GPRS 4Tx Slot), 1(WLAN) Body worn Accessory : None Tx Frequency Range : 824.2 MHz ~ 848.8 MHz (GSM850) 1850.2 MHz ~ 1909.8 MHz (PCS1900) 2412 MHz ~ 2462 MHz (WLAN) 2402 MHz ~ 2480 MHz (Bluetooth) Conducted Max Power : 33.38 dBm(GSM850), 30.79 dBm(PCS1900), 15.71 dBm(WLAN), 3.33 dBm(Bluetooth) Battery Type : 3.7 V d.c. (Lithum-ion Battery) Report File No. : F690501/RF-SAR001915-A1 Date of Issue : 2011-01-27 Page : 4 / 124 1.5 Test Environment Ambient temperature : (22 2) ° C Tissue Simulating Liquid : (22 2) ° C Relative Humidity : (55 % R.H. 1.6 Operation Configuration The device in GSM was controlled by using a Communication tester (CMU 200). Communication between the device and the tester was established by air link. And the client provided a special driver and test program which can control the frequency and power of the WLAN module. Measurements were performed at the lowest, middle and highest channels of the operating band. The EUT was set to maximum power level during all tests and at the beginning of each test the battery was fully charged. The DASY4 system measures power drift during SAR testing by comparing e-field in the same location at the beginning and at the end of measurement. Based on the RF Power and antenna separation distance, stand-alone BT SAR and simultaneous SAR evaluation are not required. Report File No. : F690501/RF-SAR001915-A1 Date of Issue : 2011-01-27 Page : 5 / 124 1.7 EVALUATION PROCEDURES - Power Reference Measurement Procedures The Power Reference Measurement and Power Drift Measurements are for monitoring the power drift of the device under test in the batch process. The Minimum distance of probe sensors to surface determines the closest measurement point to phantom surface. The minimum distance of probe sensors to surface is 4 mm. This distance cannot be smaller than the Distance of sensor calibration points to probe tip as defined in the probe properties (for example, 2.7 mm for an ET3DV6 probe type). - The entire evaluation of the spatial peak values is performed within the Post-processing engine (SEMCAD). The system always gives the maximum values for the 1 g and 10 g cubes. The algorithm to find the cube with highest averaged SAR is divided into the following stages: 1. The extraction of the measured data (grid and values) from the Zoom Scan. 2. The calculation of the SAR value at every measurement point based on all stored data (A/D values and measurement parameters) 3. The generation of a high-resolution mesh within the measured volume 4. The interpolation of all measured values from the measurement grid to the high-resolution grid 5. The extrapolation of the entire 3-D field distribution to the phantom surface over the distance from sensor to surface 6. The calculation of the averaged SAR within masses of 1 g and 10 g. The probe is calibrated at the center of the dipole sensors that is located 1 mm to 2.7 mm away from the probe tip. During measurements, the probe stops shortly above the phantom surface, depending on the probe and the surface detecting system. Both distances are included as parameters in the probe configuration file. The software always knows exactly how far away the measured point is from the surface. As the probe cannot directly measure at the surface, the values between the deepest measured point and …

Text truncated - open the document above for the full version.

Report Number: F690501/RF-RTL004426 Page: 2 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com INDEX Table of contents 1. General information --------------------------------------------------------------------------------------3 2. Transmitter radiated spurious emissions and conducted spurious emission --------------6 3. 6 ㏈ bandwidth ------------------------------------------------------------------------------------------- 20 4. Maximum peak output power --------------------------------------------------------------------------25 5. Power Spectral Density --------------------------------------------------------------------------------- 27 6. Transmitter AC Power Line Conducted Emission-------------------------------------------------32 7. Antenna Requirement ----------------------------------------------------------------------------------- 37 Report Number: F690501/RF-RTL004426 Page: 3 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 1. General Information 1.1. Testing Laboratory SGS Testing Korea Co., Ltd. - Wireless Div. 2FL, 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-dong, Korea - 705, Dongcheon-dong Suji-gu, Yongin-si, Gyeonggi-do, Korea www.electrolab.kr.sgs.com Telephone : +82 +31 428 5700 FAX : +82 +31 427 2371 1.2. Details of Applicant Applicant : LG Electronics Inc. Address : 60-39, Gasan-dong, Gumchon-gu, Seoul, 153-023, Korea Contact Person : Kim, Hyeon Kyun Phone No. : +82 +2 2033 1113 1.3. Description of EUT Kind of Product Cellular/PCS GSM Phone with Bluetooth and WLAN Model Name LG-C330i, C330i Serial Number N / A Power Supply DC 3.7 V (Li-Ion Battery) Frequency Range 2 412 ~ 2 462 ㎒ (11b/g) Modulation Technique DSSS, OFDM Number of Channels 11 Antenna Type Integral Type Antenna Gain 2.39 dBi (Peak) 1.4. Declaration by the manufacturer - WLAN & BT do not transmit simultaneously Report Number: F690501/RF-RTL004426 Page: 4 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 1.5. Test Equipment List EQUIPMENT MANUFACTURER MODEL CAL DUE. Signal Generator Agilent E4438C Mar. 31, 2011 Signal Generator Rohde & Schwarz SMR40 Jul. 18, 2011 Spectrum Analyzer R & S FSV30 May 31, 2011 Preamplifier H.P 8447F Jul. 05, 2011 Preamplifier Agilent 8449B Apr. 01, 2011 High Pass Filter Wainwright WHK3.0/18G-10SS Sep. 29, 2011 Test Receiver R & S ESU26 Apr. 08, 2011 Bilog Antenna SCHWARZBECK MESSELEKTRONIK 396 Jul. 22, 2011 Horn Antenna R & S HF 906 Oct. 08, 2011 Horn Antenna SCHWARZBECK MESSELEKTRONIK BBHA9170 Mar. 17 2012 Power sensor R & S NRP-Z81 Aug. 14, 2011 Anechoic Chamber SY Corporation L × W × H (9.6 m×6.4 m×6.6 m) Jan. 27, 2011 Two-Line V-Network R & S ENV216 Jan. 04, 2012 Test Receiver R & S ESHS10 Jul. 13, 2011 Anechoic Chamber SY Corporation L × W × H (6.5 m×3.5 m×3.5 m) N.C.R. Report Number: F690501/RF-RTL004426 Page: 5 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 1.6. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD:FCC Part15 subpart C Standard section Test Item Result 15.205(a) 15.209 15.247(d) Transmitter Radiated Spurious Emissions Conducted Spurious Emission Complied 15.247(a)(2) 6 ㏈ Bandwidth Complied 15.247(b)(3) Maximum Peak Output Power Complied 15.247(e) Power Spectral Density Complied 15.207 Transmitter AC Power Line Conducted Emission Complied 1.7. Conclusion of worst-case The field strength of spurious emission was measured in three orthogonal EUT positions(X-axis, Y-axis and Z-axis). Worst case is Y -axis. 1 Mbps is the highest output power in the 11b. 6 Mbps is the highest output power in the 11g. 1.8 Test report revision Revision Report number Description 0 F690501/RF-RTL004426 Initial Report Number: F690501/RF-RTL004426 Page: 6 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 2. Transmitter Radiated Spurious Emissions and Conducted Spurious Emission 2.1. Test Setup 2.1.1. Transmitter Radiated Spurious Emissions The diagram below shows the test setup that is utilized to make the measurements for emission from 30 ㎒ to 1 ㎓ Emissions. The diagram below shows the test setup that is utilized to make the measurements for emission from 1 ㎓ to 24 ㎓ Emissions. Report Number: F690501/RF-RTL004426 Page: 7 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do…

Text truncated - open the document above for the full version.

Test Setup Photographs Right Ear Cheek_Slide Down Right Ear Tilt_Slide Down Left Ear Cheek_Slide Down Left Ear Tilt_Slide Down Right Ear Cheek_Slide Up Right Ear Tilt_Slide Up Left Ear Cheek_Slide Up Left Ear Tilt_Slide Up Body Front_Slide Down Body Front_Slide Up Body Back_Slide Down Body Back_Slide Up Body Back_Slide Down with Ear Set Body Back_Slide Up with Ear Set

Test setup photos of EUT A. Photo of Radiated output power & Spurious Emission Test B. Photos of conducted power line test