BEJGU200ACellular/PCS GSM Phone

Part 15.21 statement " Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. “ Part 15.105 statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Part 15 Class B Compliance This device and its accessories comply with part15 of FCC rules. Operation is subject to the following two conditions: (1) This device & its accessories may not cause harmful interference. (2) This device & its accessories must accept any interference received, including interference that may cause undesired operation. Body-worn Operation This device has been tested for typical body-worn operations with the distance of 0.79inches (2.0cm) from the user’s body. To comply with FCC RF exposure requirements, a minimum separation distance of 0.79inches(2.0cm) must be maintained from the user's body. Additionally, Belt clips, holsters & other body-worn accessories may not contain metallic components. Getting to know your phone Earpiece Display screen Soft keys Each of these keys perform the functions indicated by the text on the display immediately above them. End/Power key Allows you to power the phone on or off , end calls, or return to Standby Mode. Send key You can dial a phone number and answer incoming calls. Navigation keys Use for quick access to phone functions. Menu map 1 Messaging 1 New message 2 Inbox 3 Drafts 4 Chat box 5 Outbox 6 Sent 7 Listen to voice mail 8 Info messages 9 Templates 0 Settings 6 Media 1 Camera 2 MP3 player 3 FM radio 2 Contacts 1 Search 2 New contact 3 Speed dials 4 Copy all 5 Delete all 6 Memory status 7 Information 5 My stuff 1 My images 2 My sounds 3 Others 9 Settings 1 Profi les 2 Date & Time 3 Languages 4 Display 5 Call 6 Auto keylock 7 Security 8 Power save 9 USB connection 0 Network selection * Reset settings # Memory status 8 Organiser 1 Alarm 2 Calendar 3 Memo 4 Games 1 Space ball 7 Tools 1 Torch 2 Fake call 3 Calculator 4 Stopwatch 5 Unit converter 6 World clock 7 SIM services 3 Call history 1 All calls 2 Missed calls 3 Dialled calls 4 Received calls 5 Call duration Turning Your Phone On and Off 1 Press and hold the End key until the power comes on. 2 Press and hold the End key until the power goes off . Making a call 1 Key in the number using the keypad. To delete a digit press Clear key. 2 Press to initiate the call. 3 To end the call, press . TIP! To enter + when making an international call, press and hold 0. Making a call from your contacts 1 Press “Search” contacts to open the address book. 2 Using the keypad, enter the fi rst letter of the contact you want to call. For example, for Offi ce, press 6 three times. 3 To scroll through the contacts and their diff erent numbers use “Up and Down Navigation key”. 4 Press to initiate the call. TIP! You can change the settings on your phone to answer your calls in diff erent ways. Press Menu, select Settings, choose Call. Select Answer mode and choose from Any key or Send key only. Answering and rejecting a call When your phone rings, press Accept or press to answer the call. While your phone is ringing, select Silent to mute the ringing. This is great if you have forgotten to change your profi le to Silent for a meeting. Press or Reject to reject the incoming call. TIP! You can change the settings on your phone to answer your calls in diff erent ways. Press Menu, select Settings and choose Call. Select Answer mode and choose from Any key or Send key only. Changing the call settings You can set the menu relevant to a call. Press Menu, select Settings and choose Security. • Call barring – Select when you would like calls to be barred. • Fixed dial number – Choose a list of numbers that can be called from your phone. You’ll need your PIN2 code from your operator. Only numbers included in the fi xed dial list can be called from your phone. Entering text You can enter alphanumeric characters using the phone’s keypad. For example, storing names in Contacts, writing a message and creating scheduling events in the calendar all require entering text. The following text input methods are available in the phone: T9 predictive mode, ABC manual mode and 123 mode. Note: Some fi elds may allow only one text input mode (e.g. telephone number in address book fi elds). T9 predictive mode T9 predictive mode uses a built-in dictionary to recognise words you’re writing based on the key sequences you press. Simply press the number key associated with the letter you want to enter, and the dictionary will recognise the word once all the letters are entered. ABC manual mode This mode allows you to enter letters by pressing the key labeled with the required letter once, twice, three or four times until the letter is displayed. 123 mode Type numbers using one keystroke per number. You can also add numbers while remaining in letter modes by pressing and holding the desired key. Messaging Menu 1 Your GU200a includes functions related to SMS (Short Message Service). Sending a message 1 Pr…

Text truncated - open the document above for the full version.

Date: March 22, 2010 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Lab Manager Jim. Kim and of SGS Testing Korea Co., Ltd and hereafter referred to as SGS Testing Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Lab Manager Jim. Kim of SGS Testing Korea Co., Ltd on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Testing Korea as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Jae Cheon(J.C.) Lee General Manager LG Electronics USA

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, NJ 07632 Date:March 23, 2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 RE: Request of Confidentiality for FCC ID: BEJGU200A Equipment Class: JBP: Part 15 Class B Computing Device Peripheral To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: PERMANENT AND SHORT-TERM CONFIDENTIAL LIST Exhibit Description 1 Block Diagram PERMANENT 2 Operational Descriptions 3 External Photos 4 Internal Photos 5 Test-Setup Photos SHORT-TERM 6 User’s Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, Jae Cheon(J.C.) Lee General Manager LG Electronics USA LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, NJ 07632

Test Report No. : F690501/RF-EMG003188 Page : 11 of 17 3. Photographs of EUT z Front View z Rear View

Model No: GU200a FCC ID : BEJGU200A S/N : Made in Korea LG Electronics Inc. LGE

Test Report No. : F690501/RF-EMG003188 Page : 12 of 17 z Top View of Main Board z Bottom View of Main Board Test Report No. : F690501/RF-EMG003188 Page : 13 of 17 z Top View of LCD Panel z Bottom View of LCD Panel Test Report No. : F690501/RF-EMG003188 Page : 14 of 17 z Battery z Top View of Key Board Test Report No. : F690501/RF-EMG003188 Page : 15 of 17 z Bottom View of Key Board z Antenna Test Report No. : F690501/RF-EMG003188 Page : 16 of 17 z Inside

Test Report No. : F690501/RF-EMG003188 Page : 2 of 17 Contents 1. General Information...................................................................................................3 1.1 Client Information................................................................................................3 1.2 Test Laboratory...................................................................................................3 1.3 General Information of E.U.T. .............................................................................3 1.4 Operating Modes and Conditions........................................................................3 1.5 Peripheral Equipments........................................................................................3 1.6 Cable List ............................................................................................................4 1.7 System Configurations ........................................................................................4 1.8 Test System Layout ............................................................................................4 1.9 Applicable Standards for Testing ........................................................................5 1.10 Summary of Test Results..................................................................................5 2. Emission Test............................................................................................................6 2.1 Test Results ........................................................................................................6 2.2 Test Equipments .................................................................................................6 2.3 Test Site..............................................................................................................6 2.4 Conducted Emission Test Data...........................................................................7 2.5 Radiated Emission Test Data..............................................................................8 2.6 Modifications.......................................................................................................8 2.7 Photograph of Conducted Emission....................................................................9 2.8 Photographs of Radiated Emission...................................................................10 3. Photographs of EUT ................................................................................................11 Appendix A : Conducted Emission ..............................................................................17 Test Report No. : F690501/RF-EMG003188 Page : 3 of 17 1. General Information 1.1 Client Information Applicant : LG Electronics Inc. Address of Applicant : 60-39, Gasan-dong, Gumchon-gu, Seoul, 153-023, Korea Manufacturer : LG Electronics Inc. Address of Manufacturer : 60-39, Gasan-dong, Gumchon-gu, Seoul, 153-023, Korea 1.2 Test Laboratory Name and Address : SGS Testing Korea Co., Ltd. 18-34, Sanbon-dong, Gunpo, Gyeonggi-do, Korea 435-041 1.3 General Information of E.U.T. Product Name : Cellular/PCS GSM Phone Model Name : GU200a Serial No. : 001KPLC681080 Highest Internal Frequency : Max.104 MHz 1.4 Operating Modes and Conditions Operating mode Operating condition USB Mode USB Data Communication 1.5 Peripheral Equipments Description Model Serial No.Manufacturer Notebook Computer PCG-3AHP 28272287 7000053 Sony Corporation Micro SD Card Mobile Ultra 2GBN/A SanDisk LCD Monitor CR22KS N843H1K P902165L Samsung Electronics USB Keyboard KU-0459 76914020 03981 Microsoft USB MOUSE Wheel mouse optical 0447 Microsoft Corporation Test Report No. : F690501/RF-EMG003188 Page : 4 of 17 1.6 Cable List Start END Cable Spec. Name I/O Port Name I/O PortLength Shield USB Notebook Computer USB 1.2 Shielded Cellular/PCS GSM Phone MicroSD Micro SD Card - - - DC IN AC AdapterDC OUT1.8 Unshielded RGB LCD Monitor RGB 1.8 Shielded USB USB Keyboard - 1.7 Shielded Notebook Computer USB USB Mouse- 1.8 Shielded AC Adapter AC IN AC Source- 1.0 Unshielded 1.7 System Configurations 1.8 Test System Layout Description Model Serial No. Manufacturer Antenna N/A N/A N/A Battery LGIP-430N DC100126 LG Key Board SPEY0065101-C N/A N/A LCD Panel N/A SYN98200324CN/A Main Board SPFY0222601 N/A N/A AC Adapter Notebook Computer Cellular/PCS GSM Phone Micro SD Card LCD Monitor USB Mouse USB Keyboard Test Report No. : F690501/RF-EMG003188 Page : 5 of 17 1.9 Applicable Standards for Testing 1.10 Summary of Test Results Test Item Standards Results Conducted Emission FCC Part 15, Subpart B ANSI C63.4 : 2003 CISPR 22 : 2006 Complied Radiated Emission FCC Part 15, Subpart B ANSI C63.4 : 2003 CISPR 22 : 2006 Complied Standards Status Deviation FCC Part 15, Subpart B ANSI C63.4 : 2003 CISPR 22 : 2006 Applicable No Deviation Test Report No. : F690501/RF-EMG003188 Page : 6 of 17 EMISSION 2. Emission Test 2.1 Test Results Test Items Standards Test Results Conducted Emission FCC Part 15, Subpart B ANSI C63.4 : 2003 CISPR 22 : 2006 Complied Radiated Emission FCC Part 15, Subpart B ANSI C63.4 : 2003 CISPR 22 : 2006 Complied 2.2 Test Equipments Equipment Model Manufacturer Last Cal. Date Two-Line V-Network ENV216 R&S 2010.01.06 Test Receiver ESHS10 R&S 2009.07.13 Test Receiver ESU26 R&S 2009.04.21 Amplifier 8447F HP 2009.07.02 Bi-Log Antenna VULB9163 SCHWARZBECK MESS- ELEKTRONIK 2009.07.22 Note : Only the calibration period of Antennas is 2 years but the period of every equipment is 1 year. 2.3 Test Site Conducted Emission: Shield Room in Gunpo Laboratory Radiated Emission: 3m Semi-Anechoic chamber in Gunpo Laboratory Test Report No. : F690501/RF-EMG003188 Page : 7 of 17 2.4 Conducted Emission Test Data Temperature : 22.3 Humidity : 45.0 % RH Atmospheric Pressure : 101.6 kPa FREQ. LE VEL( dB )LIMIT(dB )MARGIN(dB) (MHz)Q-PeakAverageQ-PeakAverageQ-PeakAverage 0.24H35.2022.3062.1052.1026.9029.80 0.45 31.3020.2056.8846.8825.5826.68 2.03H30.5019.7056.0046.0025.5026.30 2.73N30.8020.1…

Text truncated - open the document above for the full version.

Test Report No. : F690501/RF-EMG003188 Page : 9 of 17 2.7 Photograph of Conducted Emission Test Report No. : F690501/RF-EMG003188 Page : 10 of 17 2.8 Photographs of Radiated Emission