BEJIP100Interactive Pen

[KOREA] E-보드 펜 User Information (Model Name: AN-IP100) 목 차 1. E-보드 펜의 개요 및 제원 (1) 개 요 (2) 제 원 2. 주의 사항 3. 고 객지원 (1) 개 요 E-보드 펜은 Projector의 적외선 좌표 Data를 Pen의 수광 센서를 통해 좌표 값을 받고, 2.4GHz 대역의 무선방식으로 Projector에 다시 전송하여 사용자가 무선 Mouse의 기본 기능과 Air Drawing 펜 기능 을 수행하는 송신부 제품입니다. (2) 제 원 구 분 내 용 모 델 명 AN-IP100 주파수 대역 2400MHz ~ 2483.5MHz 채 널 29EA 송신 출력 0 dBm 수신 감도 –83 dBm 크 기 폭24 두께24, 길이177.5(mm) (공차 ± 0.8mm) 무 게 53.4g 전 원 3.7V, 900mAh (Li-Polymer) 동작 온도 0°C ~ + 45 °C 1. E-보드 펜 의 개요 및 제원 2. 주의 사항 (1) 제품 구입 후 제품 사용법에 따라 페어링 후에 사용하세요. (2) LG E-보드 펜의 배터리는 교체할 수 없으며, 수시로 USB를 통해 충전하여 사용하세요. (3) 제품을 분해하거나, 열을 가해서는 안됩니다. (4) 케이스가 손상될 정도로 극심한 충격을 줘서는 안됩니다. (5) 제품을 물에 넣어서는 안됩니다. 3. 고객 지원 PROJECTOR 매뉴얼의 서비스 연락처를 참조하세요. [KCC 인증 마크 및 인증번호] 상 호 명 : 엘지전자(주) 인증번호 : KCC-CRM-LGE-IP100 제조연월 : 2013. 제조자/제조국가 : 엘지전자(주)/대한민국 기자재의 명칭/모델명 : 특정소출력 무선기기(무선데이터통신시스템용 무선기기)/ AN-IP100 [ENGLISH] Table of Contents 1. Overview and specification of the interactive Pen (1) Overview (2) Specifications 2. Cautions 3. Customer Support (1) Overview The interactive pen is a transmitter which receives the IR coordinate data from the projector through its sensor and transmits the data back to the projector wirelessly through the 2.4 GHz band. It allows the user to use the basic functions of the wireless mouse and the Air Drawing pen function. (2) Specifications Categories Description Model Name AN-IP100 Frequency band 2400MHz ~ 2483.5MHz Channels 29EA Transmission Output 0 dBm Reception sensitivity -83 dBm Size Width 24, Thickness 24, Length 177.5(mm) (Tolerance of ± 0.8mm) Weight 53.4g Power 3.7V, 900mAh (Li-Polymer) Operating Temperature 0°C ~ + 45 °C 1. Overview and specification of the interactive Pen 2. Cautions (1) Follow the instructions in the user guide to pair the product with the projector before using it. (2) The battery of LG interactive pen can not be replaced. Charge the pen using the USB cable whenever necessary. (3) Do not disassemble the product or apply heat to the product. (4) Be careful to protect the product from heavy impact to avoid damaging the case. (5) Do not allow water to get into the product. Refer to the Customer Information Center of Projector owner's manual. 3. Customer Support [Chinese (PRC)] 目录 1. 交互式笔的概述与规格 (1) 概述 (2) 规格 2. 注意 3. 客户支持 (1) 概述 交互式笔是一种通过传感器从投影机接收红外坐标数据，再通过 2.4 GHz 带宽将所接收数据无线传 回至投影机的发射器。 它能让用户使用无线鼠标的基本功能和 Air Drawing （空中绘图）笔功能。 (2) 规格 类别 描述 型号名 AN-IP100 频带 2400MHz ~ 2483.5MHz 频道 29EA 传输输出 0 dBm 接收灵敏度 -83 dBm 大小 宽度 24， 厚度 24， 长度 177.5（毫米） （公差为正负 0.8 毫米） 重量 53.4g 功率 3.7 伏，900 毫安 （锂聚合物电池） 工作温度 0°C ~ + 45 °C 1. 交互式加密狗的概述与规格 2. 注意 (1) 使用本产品前，请按照用户指南中的说明将其与投影机配对。 (2) 不得更换 LG 交互式笔的电池。有必要时，请使用 USB 电缆为交互式笔充电。 (3) 请勿拆卸本产品或将本产品放在热源附近。 (4) 注意保护本产品不受重压，以避免损坏外壳。 (5) 请勿让水进入本产品。 参阅投影机用户手册的“客户信息中心”。 3. 客户支持 [Hungarian] Tartalomjegyzék 1. Áttekintés és az interaktív ceruza műszaki jellemzői (1) Áttekintés (2) Műszaki jellemzők 2. Óvintézkedések 3. Ügyfélszolgálat (1) Áttekintés Az interaktív ceruza olyan jeltovábbító, amely az érzékelőjén keresztül fogadja a projektortól érkező infravörös koordinátaadatokat, és vezeték nélkül, a 2,4 GHz-es sávon továbbítja az adatokat a projektornak. Lehetővé teszi a vezeték nélküli egér alapvető funkcióinak és az Air Drawing funkciónak a használatát. (2) Műszaki jellemzők Kategóriák Leírás Típus neve AN-IP100 Frekvenciasáv 2400MHz ~ 2483.5MHz Csatorna 29EA Átviteli teljesítmény 0 dBm Jelfogadási érzékenység -83 dBm Méret Szélesség 24, Vastagság 24, Hossz 177.5 (mm) (± 0.8 mm tűréshatárral) Tömeg 53.4g Áramellátás 3,7 V, 900 mAh (lítium-polimer) Üzemi hőmérséklet 0°C ~ + 45 °C 1. Áttekintés és az interaktív ceruza műszaki jellemzői 2. Óvintézkedések (1) Használat előtt a terméket párosítsa a projektorral a használati utasításban leírtaknak megfelelően. (2) Az LG interaktív ceruza akkumulátora nem cserélhető. Szükség esetén az USB-kábel segítségével töltse fel a ceruzát. (3) Ne szerelje szét és ne tegye ki hőnek a terméket. (4) Óvja a terméket az erős ütésektől, hogy elkerülje a burkolat rongálódását. (5) Ügyeljen rá, hogy ne jusson víz a termékbe. Vegye fel a kapcsolatot az ügyfélszolgálati központtal a projektor használati útmutatójában szereplő elérhetőségeken. 3. Ügyfélszolgálat [Polish] Spis treści 1. Opis i dane techniczne rysika interaktywnego (1) Opis (2) Dane techniczne 2. Uwagi 3. Pomoc techniczna dla klientów (1) Opis Rysik interaktywny jest nadajnikiem odbierającym za pomocą czujnika sygnału podczerwieni dane współrzędnych nadawane z projektora i przesyłającym dane z powrotem do projektora bezprzewodowo za pośrednictwem pasma 2,4 GHz. Umożliwia korzystanie z podstawowych funkcji myszy bezprzewodowej oraz funkcji rysowania w powietrzu. (2) Dane techniczne Kategorie Opis Nazwa modelu AN-IP100 Pasmo częstotliwości 2400MHz ~ 2483.5MHz Kanał 29EA Moc transmisji 0 dBm Czułość odbioru -83 dBm Rozmiar Szerokość 24, grubość 24, długość 177.5 (mm) (Tolerancja ± 0.8 mm) Waga 53.4g Zasilanie 3,7 V, 900 mAh (Litowo-polimerowy) Temperatura w miejscu eksploatacji 0°C ~ + 45 °C 1. Opis i dane techniczne rysika interaktywnego 2. Uwagi (1) Aby sparować urządzenie z projektorem przed rozpoczęciem korzystania z produktu, (2) Akumulatora rysika interaktywnego firmy LG nie można wymienić. Rysik należy ładować wtedy, gdy jest to konieczne, korzystając z przewodu USB. (3) Nie wolno rozmontowywać ani podgrzewać urządzenia. (4) Aby uniknąć uszkodzenia obudowy, należy zabezpieczyć urządzenie przed silnymi uderzeniami. (5) Nie wolno dopuścić do przedostania się wody do wnętrza urządzenia. Informacje na ten temat można znaleźć w sekcji „Centrum informacji klienta” instrukcji obsługi projektora. 3. Pomoc techniczna dla klientów [French (France)] Sommaire 1. Présentation et spécifications du stylet interactif (1) Présentation (2) Caractéristiques techniques 2. Précautions 3. Support technique (1) Présentation Le stylet interactif est un émetteur qui reçoit les données IR coordonnées du projecteur grâce au capteur et retransmet les données au projecteur via une connexion sans fil de 2,4 GHz. L…

Text truncated - open the document above for the full version.

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: March 15, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards;

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: March 15, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: BEJIP100 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Operational Description 3 Schematics 4 Part Lists SHORT-TERM 5 Internal Photos 6 External Photos 7 Test-Setup Photos 8 Users Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Jacob Cho Director, Standards & Compliance

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: March 15, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of Digital EMC Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: BEJIP100 including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of Digital EMC Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from LG Electronics USA. Sincerely, Jacob Cho Director, Standards & Compliance

FCCID: BEJIP100 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 1 FCCID: BEJIP100 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 2 FCCID: BEJIP100 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 3

FCC ID: BEJIP100 Copyright Ⓒ 2013, Digital EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. - The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the user's manual.

FCCID: BEJIP100 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 1 FCCID: BEJIP100 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 2 FCCID: BEJIP100 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 3 FCCID: BEJIP100 Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 4

MHzmm = ± = [ / ] * [ √ ] BEJIP100 100 2 40125 5 - Max. power with turn-up tolerance = 1 Used Step 1) SAR test exclusion thresholds for 100MHz to 6GHz at te st separationn distances ≤ 50 mm = [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] FCC ID : Standalone SAR test exclusion considerations March 20, 2013 2401.2497 - Min. test separation distance = mW -0.59 -0.59 dBm - Min. transmitting frequency = dB Typical Power:Measured Power: -0.59 dBmdBm 5 = [ / ] [ √ ] = Thus SAR for this device is not required. [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW 1 . 00 2 . 40125 ≤ 3, for 1g SAR Step 2-2) SAR test exclusion thresholds for 1500MHz to 6GHz at test separationn distances > 50 mm = N/A 5 Step 2-1) SAR test exclusion thresholds for 100MHz to 1500MHz at test separationn distances > 50 mm = N/A 0.31 Copyright Ⓒ 2013, Digital EMC Co., Ltd.

DEMC1211-02678 & DEMC1211-02680 FCCID: BEJIP100 Report No.: DRTFCC1303-0271 IC: 2703H-IP100 TRF-RF-213(01)120309 Page2 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. Test Report Version Test Report No. Date Description DRTFCC1303-0271 Mar. 20, 2013 Initial issue DEMC1211-02678 & DEMC1211-02680 FCCID: BEJIP100 Report No.: DRTFCC1303-0271 IC: 2703H-IP100 TRF-RF-213(01)120309 Page3 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. Table of Contents 1. GENERAL INFORMATION ........................................................ 4 2. EUT DESCRIPTION ................................................................... 4 3. SUMMARY OF TESTS ............................................................... 5 4. TEST METHODOLOGY ............................................................. 6 4.1 EUT CONFIGURATION ..................................................................................................... 6 4.2 EUT EXERCISE ................................................................................................................. 6 4.3 GENERAL TEST PROCEDURES ..................................................................................... 6 4.4 DESCRIPTION OF TEST MODES..................................................................................... 6 5. INSTRUMENT CALIBRATION ................................................... 7 6. FACILITIES AND ACCREDITATIONS ........................................ 7 6.1 FACILITIES ........................................................................................................................ 7 6.2 EQUIPMENT ...................................................................................................................... 7 7. ANTENNA REQUIREMENTS ..................................................... 7 8. TEST RESULT ........................................................................... 8 8.1 6dB Bandwidth ................................................................................................................. 8 8.2 Maximum Peak Conducted Output Power ................................................................... 11 8.3 Maximum Power Spectral Density ................................................................................ 13 8.4 Out of Band Emissions at the Band Edge/ Conducted Spurious Emissions ........... 16 8.5 Radiated Spurious Emissions ....................................................................................... 26 8.6 Power-line Conducted Emissions ................................................................................ 29 8.7 Occupied Bandwidth ...................................................................................................... 32 9. LIST OF TEST EQUIPMENT .................................................... 35 APPENDIX I ................................................................................. 36 DEMC1211-02678 & DEMC1211-02680 FCCID: BEJIP100 Report No.: DRTFCC1303-0271 IC: 2703H-IP100 TRF-RF-213(01)120309 Page4 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. 1. GENERAL INFORMATION Applicant : LG Electronics USA. Address : 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States FCC ID : BEJIP100 IC : 2703H-IP100 EUT : Interactive Pen Model : AN-IP100 Additional Model(s) : N/A Data ofTest : 2013-03-04 ~ 2013-03-08 Contact person : Jacob Cho 2. EUT DESCRIPTION Product Interactive Pen Model Name AN-IP100 Power Supply DC 3.7V Frequency Range 2401.249725 ~ 2481.230438 MHz Max. RF Output Power -0.59 dBm Modulation Type MSK Antenna Specification Internal Antenna Max. peak gain : 3.63 dBi DEMC1211-02678 & DEMC1211-02680 FCCID: BEJIP100 Report No.: DRTFCC1303-0271 IC: 2703H-IP100 TRF-RF-213(01)120309 Page5 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. 3. SUMMARY OF TESTS FCC Part Section(s) RSS Section(s) Parameter Limit Test Condition Status Note 1 I. Transmitter Mode (TX) 15.247(a) RSS-210 [A8.2] 6 dB Bandwidth > 500 kHz Conducted C 15.247(b) RSS-210 [A8.4] Transmitter Output Power < 1Watt C 15.247(d) RSS-210 [A8.5] Out of Band Emissions / Band Edge 20dBc in any 100kHz BW C 15.247(e) RSS-210 [A8.2] Transmitter Power Spectral Density < 8dBm / 3kHz C - RSS Gen 4.6.1 Occupied Bandwidth (99%) RSS-Gen(4.6.1) C 15.247(d) 15.205 15.209 RSS-210 [A8.5] General Field Strength Limits (Restricted Bands and Radiated Emission Limits) <FCC 15.209 limits Radiated C Note2 15.207 RSS-Gen [7.2.4] AC Conducted Emissions < FCC 15.207 limits AC Line Conducted C 15.203 - Antenna Requirements FCC 15.203 - C Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable Note 2: This test item was performed in each axis and the worst case data was reported. DEMC1211-02678 & DEMC1211-02680 FCCID: BEJIP100 Report No.: DRTFCC1303-0271 IC: 2703H-IP100 TRF-RF-213(01)120309 Page6 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. 4. TEST METHODOLOGY The measurement procedure described in the American National Standard forTesting Unlicensed Wireless Devices (ANSI C63.10-2009) and KDB558074 4.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 4.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C. 4.3 GENERAL TEST PROCEDURES Conducted Emissions According to the requirements in Section 6.2 of ANSI C63.10, the EUT is placed on the turntable, which is 0.8 m above ground plane and the conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and Average detector. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position…

Text truncated - open the document above for the full version.

FCC ID: BEJIP100 Copyright Ⓒ 2013, Digital EMC Co., Ltd. EUT Position EUT Position: X-axis EUT Position: Y-axis EUT Position: Z-axis FCC ID: BEJIP100 Copyright Ⓒ 2013, Digital EMC Co., Ltd. 1GHz-18GHz FCC ID: BEJIP100 Copyright Ⓒ 2013, Digital EMC Co., Ltd. Conducted Emissions