BEJIP100DInteractive dongle

[KOREA] E-보드 동글 User Information (Model Name: AN-IP100D) 목 차 1. E-보드 동글의 개요 및 제원 (1) 개 요 (2) 제 원 2. 주의 사항 3. 고 객지원 (1) 개 요 E-보드 동글은 Projector의 Interactive Port에 연결되어, E-보드 펜으 로부터 2.4GHz 대역의 무선 방식으로 좌표 값을 받고, 좌표 Data를 Projector에 전송하여 사용자가 Mouse의 기본 기능과 Air Drawing 기 능을 수행할 수 있도록 하는 수신부 제품 입니다. (2) 제 원 구 분 내 용 모 델 명 AN-IP100D 주파수 대역 2400MHz ~ 2483.5MHz 채 널 29EA 송신 출력 0 dBm 수신 감도 –82 dBm 크 기 폭19.4, 두께9.3, 길이49.6(mm) (공차 ± 0.8mm) 무 게 7.8g 전 원 USB 5V 동작 온도 0°C ~ + 50 °C 1. E-보드 동글의 개요 및 제원 2. 주의 사항 (1) 제품 구입 후 제품 사용법에 따라 페어링 후에 사용하세요. (2) 제품을 분해하거나, 열을 가해서는 안됩니다. (3) 케이스가 손상될 정도로 극심한 충격을 줘서는 안됩니다. (4) 제품을 물에 넣어서는 안됩니다. PROJECTOR 매뉴얼의 서비스 연락처를 참조하세요. [KCC 인증 마크 및 인증번호] 상 호 명 : 엘지전자(주) 인증번호 : KCC-CRM-LGE-IP100D 제조연월 : 2013. 제조자/제조국가 : 엘지전자(주)/대한민국 기자재의 명칭/모델명 : 특정소출력 무선기기(무선데이터통신시스템용 무선기기)/ AN-IP100D 3. 고객 지원 [ENGLISH] Table of Contents 1. Overview and specification of the interactive Dongle (1) Overview (2) Specifications 2. Cautions 3. Customer Support (1) Overview The interactive dongle is a receiver for the interactive pen. It should be connected to the interactive port of the projector. It will receive coordinate information from the interactive pen using a 2.4 GHz wireless signal. It allows the user to use the basic functions of a mouse and the Air Drawing functions. (2) Specifications Categories Description Model Name AN-IP100D Frequency band 2400MHz ~ 2483.5MHz Channels 29EA Transmission Output 0 dBm Reception sensitivity -82 dBm Size Width19.4, Thickness 9.3, Length 49.6(mm) (Tolerance of ± 0.8mm) Weight 7.8g Power USB 5V Operating Temperature 0°C ~ + 50 °C 1. Overview and Specifications of the Interactive Dongle 2. Cautions (1) Follow the instructions in the user guide to pair the product with the projector before using it. (2) Do not disassemble the product or apply heat to the product. (3) Be careful to protect the product from heavy impact to avoid damaging the case. (4) Do not allow water to get into the product. Refer to the Customer Information Center of Projector owner's manual. 3. Customer Support [Chinese (PRC)] 目录 1. 交互式加密狗的概述与规格 (1) 概述 (2) 规格 2. 注意 3. 客户支持 (1) 概述 交互式加密狗是交互式笔的接收器。 它应连接至投影机的交互端口。 它会利用 2.4 GHz 无线信号接收交互式笔的坐标信息。 它为用户提供鼠标的基本功能和 Air Drawing （空中绘图）功能。 (2) 规格 类别 描述 型号名 AN-IP100D 频带 2400MHz ~ 2483.5MHz 频道 29EA 传输输出 0 dBm 接收灵敏度 -82 dBm 大小 宽度 19.4， 厚度 9.3， 长度 49.6 (毫米) （公差为正负 0.8 毫米） 重量 7.8g 功率 USB 5V 工作温度 0°C ~ + 50 °C 1. 交互式加密狗的概述与规格 2. 注意 (1) 使用本产品前，请按照用户指南中的说明将其与投影机配对。 (2) 请勿拆卸本产品或将本产品放在热源附近。 (3) 注意保护本产品不受重压，以避免损坏外壳。 (4) 请勿让水进入本产品。 参阅投影机用户手册的“客户信息中心”。 3. 客户支持 [Hungarian] Tartalomjegyzék 1. Áttekintés és az interaktív hardverkulcs műszaki jellemzői (1) Áttekintés (2) Műszaki jellemzők 2. Óvintézkedések 3. Ügyfélszolgálat (1) Áttekintés Az interaktív hardverkulcs az interaktív ceruza fogadóegysége. A hardverkulcsot a projektor interaktív portjához kell csatlakoztatni. A hardverkulcs az interaktív ceruza koordinátáival kapcsolatos információt 2,4 GHz-es vezeték nélküli jel használatával kapja. Lehetővé teszi az egér alapvető funkcióinak és az Air Drawing funkcióinak a használatát. (2) Műszaki jellemzők Kategóriák Leírás Típus neve AN-IP100D Frekvenciasáv 2400MHz ~ 2483.5MHz Csatorna 29EA Átviteli teljesítmény 0 dBm Jelfogadási érzékenység -82 dBm Méret Szélesség 19.4, Vastagság 9.3, Hossz 49.6 (mm) (± 0.8 mm tűréshatárral) Tömeg 7.8g Áramellátás USB 5V Üzemi hőmérséklet 0°C ~ + 50 °C 1. Áttekintés és az interaktív hardverkulcs műszaki jellemzői 2. Óvintézkedések (1) Használat előtt a terméket párosítsa a projektorral a használati utasításban leírtaknak megfelelően. (2) Ne szerelje szét és ne tegye ki hőnek a terméket. (3) Óvja a terméket az erős ütésektől, hogy elkerülje a burkolat rongálódását. (4) Ügyeljen rá, hogy ne jusson víz a termékbe. Vegye fel a kapcsolatot az ügyfélszolgálati központtal a projektor használati útmutatójában szereplő elérhetőségeken. 3. Ügyfélszolgálat [Polish] Spis treści 1. Opis i dane techniczne interaktywnego modułu sterującego (1) Opis (2) Dane techniczne 2. Uwagi 3. Pomoc techniczna dla klientów (1) Opis Interaktywny moduł sterujący jest odbiornikiem sygnału rysika interaktywnego. Należy go podłączyć do interaktywnego portu projektora. Moduł sterujący odbiera informacje o pozycji wysyłane przez rysik interaktywny za pośrednictwem sygnału bezprzewodowego o częstotliwości 2,4 GHz. Umożliwia korzystanie z podstawowych funkcji myszy oraz funkcji rysowania w powietrzu. (2) Dane techniczne Kategorie Opis Nazwa modelu AN-IP100D Pasmo częstotliwości 2400MHz ~ 2483.5MHz Kanał 29EA Moc transmisji 0 dBm Czułość odbioru -82 dBm Rozmiar Szerokość 19.4, grubość 9.3, długość 49.6 (mm) (Tolerancja ± 0.8 mm) Waga 7.8g Zasilanie USB 5V Temperatura w miejscu eksploatacji 0°C ~ + 50 °C 1. Opis i dane techniczne interaktywnego modułu sterującego 2. Uwagi (1) Aby sparować urządzenie z projektorem przed rozpoczęciem korzystania z produktu, należy postępować zgodnie z instrukcjami znajdującymi się w instrukcji obsługi. (2) Nie wolno rozmontowywać ani podgrzewać urządzenia. (3) Aby uniknąć uszkodzenia obudowy, należy zabezpieczyć urządzenie przed silnymi uderzeniami. (4) Nie wolno dopuścić do przedostania się wody do wnętrza urządzenia. Informacje na ten temat można znaleźć w sekcji „Centrum informacji klienta” instrukcji obsługi projektora. 3. Pomoc techniczna dla klientów [French (France)] Sommaire 1. Présentation et spécifications du module de sécurité interactif (1) Présentation (2) Caractéristiques techniques 2. Précautions 3. Support technique (1) Présentation Le module interactif est un récepteur pour le stylet interactif. Il doit être connecté au port interactif du projecteur. Il reçoit des informations coordonnées du stylet interactif via un signal de 2,4 GHz. Il permet à l'utilisateur de se servir des fonctions de base d'une souris et de celles de la fonction Air Drawing. (2) Caractéristiques techniques Catégories Description Modèle AN-IP100D Bande de fréquence 2400MHz ~ 2483.5MHz Canal 29EA Sortie de transmission 0 dBm Sensibilité de réception -82 dBm…

Text truncated - open the document above for the full version.

April 4, 2013 Attestation Letter Product Name: Interactive Dongle Brand Name: LG FCCID: BEJIP100D Model No. : AN-IP100D To whom it may concern, We, LG Electronics Inc. hereby declares This device is only workable when this device is connected with a projector which has DLP technology of Texas Instrument. Therefore when this device is connected with PC or Laptop, this device is never workable. Best regards. Contact Person: Jang ByeongKyu TEL: 82-31-610-5848 FAX: 82-31-610-9620 LG Eletronics. Inc.

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: March 15, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards;

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: March 15, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: BEJIP100D To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Operational Description 3 Schematics 4 Part Lists SHORT-TERM 5 Internal Photos 6 External Photos 7 Test-Setup Photos 8 Users Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Jacob Cho Director, Standards & Compliance

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: March 15, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of Digital EMC Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: BEJIP100D including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of Digital EMC Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from LG Electronics USA. Sincerely, Jacob Cho Director, Standards & Compliance

FCCID: BEJIP100D Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 1 FCCID: BEJIP100D Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 2 FCCID: BEJIP100D Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 3

FCC ID: BEJIP100D Copyright Ⓒ 2013, Digital EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. - The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the user's manual.

FCCID: BEJIP100D Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 1 FCCID: BEJIP100D Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 2 FCCID: BEJIP100D Copyright Ⓒ 2013, DIGITAL EMC Co., Ltd. View 3

MHzmm = ± = [ / ] * [ √ ] BEJIP100D 100 2 40125 5 - Max. power with turn-up tolerance = 1 Used Step 1) SAR test exclusion thresholds for 100MHz to 6GHz at te st separationn distances ≤ 50 mm = [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] FCC ID : Standalone SAR test exclusion considerations March 20, 2013 2401.2497 - Min. test separation distance = mW -0.45 -0.45 dBm - Min. transmitting frequency = dB Typical Power:Measured Power: -0.45 dBmdBm 5 = [ / ] [ √ ] = Thus SAR for this device is not required. [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW 1 . 00 2 . 40125 ≤ 3, for 1g SAR Step 2-2) SAR test exclusion thresholds for 1500MHz to 6GHz at test separationn distances > 50 mm = N/A 5 Step 2-1) SAR test exclusion thresholds for 100MHz to 1500MHz at test separationn distances > 50 mm = N/A 0.31 Copyright Ⓒ 2013, Digital EMC Co., Ltd.

DEMC1211-02682 & DEMC1211-02684 FCCID: BEJIP100D Report No.: DRTFCC1303-0272 IC: 2703H-IP100D TRF-RF-213(01)120309 Page2 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. Test Report Version Test Report No. Date Description DRTFCC1303-0272 Mar. 20, 2013 Initial issue DEMC1211-02682 & DEMC1211-02684 FCCID: BEJIP100D Report No.: DRTFCC1303-0272 IC: 2703H-IP100D TRF-RF-213(01)120309 Page3 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. Table of Contents 1. GENERAL INFORMATION ........................................................ 4 2. EUT DESCRIPTION ................................................................... 4 3. SUMMARY OF TESTS ............................................................... 5 4. TEST METHODOLOGY ............................................................. 6 4.1 EUT CONFIGURATION ..................................................................................................... 6 4.2 EUT EXERCISE ................................................................................................................. 6 4.3 GENERAL TEST PROCEDURES ..................................................................................... 6 4.4 DESCRIPTION OF TEST MODES..................................................................................... 6 5. INSTRUMENT CALIBRATION ................................................... 7 6. FACILITIES AND ACCREDITATIONS ........................................ 7 6.1 FACILITIES ........................................................................................................................ 7 6.2 EQUIPMENT ...................................................................................................................... 7 7. ANTENNA REQUIREMENTS ..................................................... 7 8. TEST RESULT ........................................................................... 8 8.1 6dB Bandwidth ................................................................................................................. 8 8.2 Maximum Peak Conducted Output Power ................................................................... 11 8.3 Maximum Power Spectral Density ................................................................................ 13 8.4 Out of Band Emissions at the Band Edge/ Conducted Spurious Emissions ........... 16 8.5 Radiated Spurious Emissions ....................................................................................... 26 8.6 Power-line Conducted Emissions ................................................................................ 29 8.7 Occupied Bandwidth ...................................................................................................... 32 9. LIST OF TEST EQUIPMENT .................................................... 35 APPENDIX I ................................................................................. 36 DEMC1211-02682 & DEMC1211-02684 FCCID: BEJIP100D Report No.: DRTFCC1303-0272 IC: 2703H-IP100D TRF-RF-213(01)120309 Page4 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. 1. GENERAL INFORMATION Applicant : LG Electronics USA. Address : 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States FCC ID : BEJIP100D IC : 2703H-IP100D EUT : Interactive dongle Model : AN-IP100D Additional Model(s) : N/A Data ofTest : 2013-03-04 ~ 2013-03-08 Contact person : Jacob Cho 2. EUT DESCRIPTION Product Interactive dongle Model Name AN-IP100D Power Supply DC 5V Frequency Range 2401.249725 ~ 2481.230438 MHz Max. RF Output Power -0.45 dBm Modulation Type MSK Antenna Specification Internal Antenna Max. peak gain : 3.65 dBi DEMC1211-02682 & DEMC1211-02684 FCCID: BEJIP100D Report No.: DRTFCC1303-0272 IC: 2703H-IP100D TRF-RF-213(01)120309 Page5 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. 3. SUMMARY OF TESTS FCC Part Section(s) RSS Section(s) Parameter Limit Test Condition Status Note 1 I. Transmitter Mode (TX) 15.247(a) RSS-210 [A8.2] 6 dB Bandwidth > 500 kHz Conducted C 15.247(b) RSS-210 [A8.4] Transmitter Output Power < 1Watt C 15.247(d) RSS-210 [A8.5] Out of Band Emissions / Band Edge 20dBc in any 100kHz BW C 15.247(e) RSS-210 [A8.2] Transmitter Power Spectral Density < 8dBm / 3kHz C - RSS Gen 4.6.1 Occupied Bandwidth (99%) RSS-Gen(4.6.1) C 15.247(d) 15.205 15.209 RSS-210 [A8.5] General Field Strength Limits (Restricted Bands and Radiated Emission Limits) <FCC 15.209 limits Radiated C Note2 15.207 RSS-Gen [7.2.4] AC Conducted Emissions < FCC 15.207 limits AC Line Conducted C 15.203 - Antenna Requirements FCC 15.203 - C Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable Note 2: This test item was performed in each axis and the worst case data was reported. DEMC1211-02682 & DEMC1211-02684 FCCID: BEJIP100D Report No.: DRTFCC1303-0272 IC: 2703H-IP100D TRF-RF-213(01)120309 Page6 / 36 Copyright ○ C 2013, Digital EMC Co., Ltd. 4. TEST METHODOLOGY The measurement procedure described in the American National Standard forTesting Unlicensed Wireless Devices (ANSI C63.10-2009) and KDB558074 4.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 4.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C. 4.3 GENERAL TEST PROCEDURES Conducted Emissions According to the requirements in Section 6.2 of ANSI C63.10, the EUT is placed on the turntable, which is 0.8 m above ground plane and the conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and Average detector. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to dete…

Text truncated - open the document above for the full version.

FCC ID: BEJIP100D Copyright Ⓒ 2013, Digital EMC Co., Ltd. EUT Position EUT Position: X-axis EUT Position: Y-axis EUT Position: Z-axis FCC ID: BEJIP100D Copyright Ⓒ 2013, Digital EMC Co., Ltd. 1GHz-18GHz FCC ID: BEJIP100D Copyright Ⓒ 2013, Digital EMC Co., Ltd. Conducted Emissions