BEJNS50PDP09PLASMA TV/MONITOR

Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. PLASMA TV OWNER’S MANUAL 42PG1050PG10 42PG2050PG20 42PG20C50PG20C 50PG3060PG30 NS-42PDP-09 NS-50PDP-09 P/NO : SAC30708031 (0801-REV00) www.lgusa.com / www.lg.ca / www.lgcommercial.com As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). 1 WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. FCC NOTICE Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera- ture accompanying the appliance. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. NOTE TO CABLE/TV INSTALLER This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. 2 IMPORTANT SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction: Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. When mounting a TV it on the wall, make sure not to install TV bythe hanging power and sig- nal cables on the back of the TV. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Unplug this apparatus when unused for long periods of time. 1 2 3 4 5 6 7 8 9 3 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Never touch this apparatus or antenna during a thunder or lighting storm. Do not allow a impact shock or any objects to fall into the product, and do not drop onto the screen with something. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged i…

Text truncated - open the document above for the full version.

PICTURE CONTROL 49 Select your desired menu option. Select PICTURE . Select Picture M Mode . Select Expert C Control . Select Expert1 or Expert2 . 1 MENU 3 2 ENTER ENTER 4 ENTER 5 ENTER Make appropriate adjustments. 6 Picture Mode - Expert Control By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. 7 RETURN Return to the previous menu. MENU Return to TV viewing. Enter Move PICTURE E Aspect Ratio : 16:9 Picture Mode : Standard • Contrast90 • Brightness50 • Sharpness60 • Color60 • Tint0 • Advanced Control RG Enter Move PICTURE E Aspect Ratio : 16:9 Picture Mode : Standard • Contrast90 • Brightness50 • Sharpness60 • Color60 • Tint0 • Expert Control RG Vivid Standard Cinema Sport Game Expert1 Expert2 F Off G Fresh Contrast Noise Reduction Off Gamma Medium Black Level Auto Off Film Mode Color Standard HD White Balance Normal Red Contrast 50 Close E PICTURE CONTROL 50 PICTURE IMPROVEMENT TECHNOLOGY PICTURE CONTROL Fresh Contrast: Optimizes the contrast automatically according to the brightness of the reflection. Fresh Color: Adjusts the color of the reflection automatically to reproduce as close as possible natural colors. Noise Reduction: Removes interference up to the point where it does not damage the original picture. Gamma: High gamma values display whitish images and low gamma values display high contrast images. Select PICTURE . Select Advanced C Control . Select Fresh C Contrast , Fresh CColor , Noise R Reduction , or Gamma . 1 MENU 3 2 ENTER ENTER 5 RETURN Return to the previous menu. MENU Return to TV viewing. Select your desired options. 4 Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Color Temperature Medium Fresh Contrast F Off G Fresh Color Off Noise Reduction Auto Gamma Medium Black Level Low Film Mode Off Close PICTURE CONTROL 51 ADVANCED CONTROL - BLACK (DARKNESS) LEVEL Adjusting the contrast and the brightness of the screen using the black level of the screen. This feature is disable in DTV and RGB-PC mode. Select PICTURE . Select Advanced C Control . Select Black L Level . 1 MENU 3 2 ENTER ENTER Select Low or High . 4 ■ Low : The reflection of the screen gets darker. ■ High : The reflection of the screen gets brighter. ■ Auto : Realizing the black level of the screen and set it to High or Low auto- matically. 5 RETURN Return to the previous menu. MENU Return to TV viewing. Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Color Temperature Medium Fresh Contrast Off Fresh Color Off Noise Reduction Auto Gamma Medium Black Level F Low G Film Mode Off Close PICTURE CONTROL 52 ADVANCED CONTROL - FILM MODE PICTURE CONTROL Set up the TV for the best picture appearance for viewing movies. When you operate Film Mode (3:2 Pull-Down Mode or Cinema Correction Mode), the TV will adjust 24 fps video from movies to 30 fps video for display. This feature operates only in TV (Analog TV/CATV, Digital DTV/CADTV), AV1, AV2, Component 480i/1080i, and HDMI 1080i mode. Select PICTURE . Select Advanced C Control . Select Film M Mode . 1 MENU 3 2 ENTER ENTER Select On or Off . 4 5 RETURN Return to the previous menu. MENU Return to TV viewing. Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Color Temperature Medium Fresh Contrast Off Fresh Color Off Noise Reduction Auto Gamma Medium Black Level Low Film Mode F Off G Close PICTURE CONTROL 53 PICTURE RESET Settings of the selected picture modes return to the default factory settings. Select PICTURE . Select Reset . Initialize the adjusted value. 1 MENU 3 2 ENTER ENTER 4 MENU Return to TV viewing. Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Enter Move PICTURE E RG • Contrast50 • Brightness50 • Sharpness50 • Color50 • Tint0 • Advanced Control • Reset Screen (RGB-PC) Resetting video configuration... i PICTURE CONTROL 54 IMAGE STICKING MINIMIZATION (ISM) METHOD PICTURE CONTROL A frozen still picture from a PC/video game displayed on the screen for prolonged periods can result in a ghost image. You can use Orbiter to help prevent image sticking. The other two functions are for removing a ghost image. G An excessive ghosted image may be impossible to clear entirely with White Wash. To return to nor- mal viewing, press the any button. NOTE ! ■ Normal : If image sticking is never a problem, ISM is not necessary - set to Normal. ■ Orbiter : Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a ghost image on the screen, the image will move every 2 min- utes. ■ Inversion : Inversion will automatically invert the plasma display panel color every 30 minutes. ■ White WWash : White Wash removes ghost images from the screen. Use spar- ingly. Watch the TV normally for a while before using this feature to see if the ghost image disappears on its own. Select OPTION . Select ISM M Method . 1 MENU 2 ENTER Select Normal, O Orbiter, Inversion or White WWash. 3 ENTER 4 RETURN Return to the previous menu. MENU Return to TV viewing. Enter Move OPTION Language: English Input Label SIMPLINK: On Key Lock: Off Caption: Off ISM Method: Normal Power Saving: Level 0 Set ID: 1 Enter Move OPTION Language: English Input Label SIMPLINK: On Key Lock: Off Caption: Off ISM Method: Normal Power Saving: Level 0 Set ID: 1 Normal Orbiter…

Text truncated - open the document above for the full version.

LG Electronics USA. Date:Jan 28,2008 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Jin-Mo Yang,Engineering Manager of ESTECH Co., Ltd. and hereafter referred to as ESTECH, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Jin-Mo Yang,Engineering Manager of ESTECH Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ESTECH as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Mr.Daniel Kim,General Manager LG Electronics USA. REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

1000 Sylvan Avenue Englewood Cliffs, NJ 07632 TEL : +847-941-8373 Federal Communications Commission Authorization and Evaluation Division FCC ID : BEJNS50PDP09 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Curcuit Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the data of the Grant for this application. Sincerely, Mr.Daniel Kim,General Manager LG Electronics USA. TEL : +847-941-8373

150 kHz30 MHz 1 PK CLRWR 2 AV CLRWR SGL TDF 6DB dBμV dBμV RBW 9 kHz MT 1 s PREAMP OFFAtt 10 dB AUTO PRN 1 MHz10 MHz 0 10 20 30 40 50 60 70 80 90 LIMIT CHECK PASS EN55022A EN55022Q Comment: NS-50PDP-09_HOT Date: 23.JAN.2008 21:45:59 150 kHz30 MHz 1 PK CLRWR 2 AV CLRWR SGL TDF 6DB dBμV dBμV RBW 9 kHz MT 1 s PREAMP OFFAtt 10 dB AUTO PRN 1 MHz10 MHz 0 10 20 30 40 50 60 70 80 90 LIMIT CHECK PASS EN55022A EN55022Q Comment: NS-50PDP-09_NEUTRAL Date: 23.JAN.2008 21:40:14