BEJRD5130CDMA Cellular Phone

LG-RD5130 User Guide CDMA PHONE Contents Introduction Highlights Important Information Check Accessories Before You Start FCC RF EXPOSURE INFORMATION Chapter 1. Getting Started Cautions Phone Overview On screen Icons Chapter 2. Basic Functions Turning the Phone On and Off Making a Call Correcting Dialing Mistakes Receiving Calls Emergency Dialing Speed Dialing Phone Book Features Chapter 3. Menu Features General Guidelines to MENU Access and Settings Names Messages Call History Profiles Setting Planner System Chapter 4. Book Features Names Chapter 5. Message Features Write Message Inbox Outbox Voice Mail Archive Draft Templates Erase Messages Settings Chapter 6. Functions used during a call Scratch pad Mute Voice Privacy Send my number Short DTMF Chapter 7. Accessories Appendix 1. Installation Appendix 2. RF Exposure Statement Chapter 1. Getting Started Cautions ??Using the phone in proximity to receiving equipment (i.e., TV or radio) may cause interference. ??Keep your phone in a safe place when not in use. ??Only use the batteries, antennas, and chargers provided by LG. Using the wrong accessories could void your warranty. ??Only authorized personnel should service the phone and its accessories. Faulty installation or service may result in accidents and consequently invalidate the warranty. ??Do not hold the antenna while the phone is in use. ??Do not use the phone in designated “no cellular phone use” areas. ??Do not expose the phone to high temperature or humidity. ??Avoid getting your phone wet. If the phone gets wet, turn the power off immediately and remove the battery pack. If the phone is mal-functional, return it to the dealer for service. ??Avoid shock or impact on the phone. Phone Overview Function Key Descriptions Lamp The light goes on when you use the power key to turn on the phone and when there are incoming calls and messages. LCD screen Displays messages & indicator icons. END/PWR Used to turn power on/off. This key disconnects a call. Using this key, you can also exit out of a menu back to the phone’s standby display without changing the setting. SEND Allows user to place or answer calls. Mouse Key This mouse key allows quick access to text and voice mail notification messages. Profiles, R- World, and RingTone menu. And these keys are used to scroll through the memory locations and menu items. Alphanumeric Keypad These keys enable you to enter numbers and characters and choose menu items. Soft Keys The current operation of a soft key is defined by the word at the bottom of the display. Soft Keys 2 : If you press this key once in a menu, you can go back one level and if you press and hold the key in a menu, you can go back to the standby display. Side Keys These keys enable you to adjust keybeep volume (in standby mode) and earpiece volume (in a call status). Star/Pound Key - In the standby status, set the manner mode by pressing the [ * ]button. (for 2 seconds) - In the standby status, set the lock function by pressing the [ # ]button. (for 2 seconds) Clear Key This key erase character and In the standby status, you can go MyMenu On screen Icons The phone screen displays several onscreen icons and onscreen icons appears when the phone is power on. Icons Descriptions Displays the strength of the signal received by the phone and current signal strength is indicated as the number of bars displayed on the screen. No service The phone is not receiving a system signal. In use A call is in progress. No icon indicates the phone is in standby mode. Digital indicator Digital service is available. Analog indicator Analog service is unavailable Indicates that a text message or voice mail has been received Roaming The phone is outside of its home service area. Charge level Indicates battery charge level. D Chapter 2. Basic Functions Turning the Phone On and Off Turning the Phone On 1. Install a charged battery pack or connect the phone to an external power source such as the cigarette lighter adapter or car kit. 2. Press [END/PWR] for a few seconds until the red light on the top of the phone flashes. ??Fully extend the antenna for the best performance. <Note> Like any other radio device, avoid any unnecessary contact with the antenna while your phone is on. Turning the Phone Off 1. Press and hold until display screen will be turned off, and then release the key. 2. Protect the antenna by pushing it back into the phone, if extended. Making a Call When you make a call, follow these simple steps: 1. Make sure the phone is turned on. ??If not, press [END/PWR]. 2. Enter the phone number with area code, if needed. 3. Press [SEND]. ??If the phone is locked, enter the lock code. ??“Call Failed” indicates that the call did not go through. 4. Press [END/PWR] to disconnect the call. Correcting Dialing Mistakes If you make mistakes in dialing a number, press [CLR] key once to erase the last entered digit or hold down [CLR] for at least two second to delete all digits, or simply press soft key 2 [BACK] to exit dialing state. Receiving Calls 1. When the phone rings, open cellcase or If cellcase is open, press any key (except [END/PWR], [?][?], [?((]) to answer. ??If you press the key [END/PWR], Side Keys ([(][(]) once when you receive a call, you can hold the present call and ring sound or vibration stops. If you press the [END/PWR] key, Side Keys ([(][(]) twice, the present call is terminated. 2. Press [END/PWR] to disconnect the call. In call waiting mode, the present call is on hold as you answer another incoming call. This service is provided by your service provider. When the call waiting function is activated, your phone will beep to let you know if you have an incoming call. Your phone may also display the incoming caller’s identification. Dialing a call from Phone Book You can place a call from any memory location either by speed dialing or by pressing [SEND] while looking up the memory location. One-Touch Dialing : One-touch dialing is a convenient feature which enables you to dial freq…

Text truncated - open the document above for the full version.

Jan 20. 2004 Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 In re : LG Electronics Inc.. FCC ID: BEJRD5130 Single - Mode Cellular Phone (CDMA) Part 22 Certification Request for Confidentiality Gentlemen: In accordance with 0.459 of CFR 47, LG Electronics, Inc. hereby requests confidentiality of the Block Diagram, Schematic Diagrams, Operational Description, Technical Specification, Parts List, and Tune-Up Procedure for the above-referenced certification application. These documents contain detailed system and equipment description and related information about the product which LG Electronics Inc. Considers to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, LG Electronics Inc. considers this information to be of benefit to its competitors, such that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, E.S.Park Research Engineer CDMA Handset Lab LG Electronics Inc. Tel : 82- 2- 850-3850 Fax : 82- 2- 850-3855 [email protected] 459- 9, Kasan-dong,Kemchun-ku Seoul 153- 023, Korea LG Electronics Inc. LGE

AFFIDAVIT FOR ESN PROTECTION OF CELLULAR MOBILE TELEPHONES We hereby certify that the LGE Handheld Portable Cellular Telephone(FCC ID: BEJRD5130) is so designed that it complies with all the requirements for ESN protection specified in section 22.919 of the FCC Rules. A) The transmitter in service has a unique ESN. B) The ESN host component is permanently attached to a main circuit board of the mobile transmitter and the integrity of the unit operating software cannot be altered. The ESN is plated from fraudulent contact and tampering. The ESN is encoded using multiplication by a polynomial and the ESN data programmed in the memory with other information. C) The ESN is factory-set and cannot be altered, transferred, removed or otherwise able to be manipulated. Cellular mobile equipment is specifically designed such that any attempt to remove, tamper with, or change the ESN chip, its logic system, or firmware originally programmed by the manufacturer will render the mobile transmitter inoperative. Sincerely, E.S.Park Research Engineer CDMA Handset Lab LG Electronics Inc. Tel : 82-2-850-3850 Fax : 82-2-850-3855 [email protected] 459-9, Kasan-dong,Kemchun-ku Seoul 153-023, Korea LG Electronics Inc. LGE

1 Chris Harvey From:Chris Harvey [[email protected]] Sent:Friday, February 06, 2004 4:18 PM To:[email protected] Subject:FW: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD5130 LG-RD5130 Internal Photos.pdf ... -----Original Message----- From: Helen Zhao [mailto:[email protected]] Sent: Wednesday, February 04, 2004 2:12 PM To: 'Chris Harvey' Subject: RE: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD5130 Hello Chris, I just received the updated Internal Photos from LG. Please kindly review. Thank you! Helen -----Original Message----- From: Chris Harvey [mailto:[email protected]] Sent: Saturday, January 31, 2004 2:54 AM To: 'Helen Zhao' Subject: RE: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD5130 Helen, yes I will accept the bandwidth measurement as included in the original report as well as the e-mail response for 1M25F9W designator. I will review the other e-mails about the responses to the other question and see if this can be closed (so many e-mails). :-) Thanks for your help, Chris -----Original Message----- From: Helen Zhao [mailto:[email protected]] Sent: Friday, January 30, 2004 9:16 PM To: Chris Harvey Subject: RE: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD5130 Hello Chris, This is Helen Zhao, I am in charge of this account in CCS. Though they called it Occupied Bandwidth in the report, actually they measured 99% bandwidth. Can you accept this? If you have further requirement, please let me know. 2 Thank you! Helen -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Friday, January 30, 2004 5:43 PM To: Helen Zhao Cc: ???; ???; ???; ???; ???; ???; Chris Harvey Subject: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD5130 Hello Helen, We have done the 99% bandwidth test. The test result is included page 8, 13 in the last RF report. I resend the test result. Best Regards. --------------------------------------------------- Lee Cheol-Goo Research Engineer QE Gr. CDMA HANDSETS LABORATORY / CDMA HANDSETS DIVISION TELECOMMUNICATION EQUIPMENT & HANDSET COMPANY 459-9, Kasan-dong, Kumchon-gu, Seoul 153-023, Korea Phone : +82-2-850-3860, +82-2-818-4272,4676 FAX : +82-2-850-3855 Mobile Phone : +82-11-756-7160 E-mail : [email protected] --------------------------------------------------- ---------- ?? ??? ---------- ??? : Helen Zhao <[email protected]> ??? : CDMA?)QE?? ??? ??([email protected], 82-2-850-3860) ? ? : 04/1/31 9:59:33 AM ? ? : RE: Re : RE: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD513 0 Hello Cheol-Goo, Attached please find the example report for 99%BW measurement. Please reference this to complete the test asap. Thank you! Helen -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Friday, January 30, 2004 4:13 PM To: Helen Zhao 3 Cc: ???; ???; ???; ???; ???; ???; Chris Harvey Subject: Re : RE: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD513 0 Hello Helen, Please let me know about the test procedure for 99% BW measurement. Thank you! --------------------------------------------------- Lee Cheol-Goo Research Engineer QE Gr. CDMA HANDSETS LABORATORY / CDMA HANDSETS DIVISION TELECOMMUNICATION EQUIPMENT & HANDSET COMPANY 459-9, Kasan-dong, Kumchon-gu, Seoul 153-023, Korea Phone : +82-2-850-3860, +82-2-818-4272,4676 FAX : +82-2-850-3855 Mobile Phone : +82-11-756-7160 E-mail : [email protected] --------------------------------------------------- ---------- ?? ??? ---------- ??? : Helen Zhao <[email protected]> ??? : CDMA?)QE?? ??? ??([email protected], 82-2-850-3860) ? ? : 04/1/31 9:02:56 AM ? ? : RE: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD513 0 Hello Cheol-Goo, We understand that for CDMA the emission designator is 1M25F9W, and this is exactly what we submitted on 731 Form (to FCC). But per FCC requirement, you need show real measurement to prove this device is a real CDMA device. Most common way is to provide additional 99% bandwidth measurement. Do you have the test procedure for 99% BW measurement, if not, I will send you information. Best Regards, Helen -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Friday, January 30, 2004 3:19 PM To: Helen Zhao Cc: ???; ???; ???; ???; ???; ???; Chris Harvey Subject: Re : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD5130 Hello, Helen, Emission Designator is 1M25F9W for CDMA operation. Thank you! --------------------------------------------------- 4 Lee Cheol-Goo Research Engineer QE Gr. CDMA HANDSETS LABORATORY / CDMA HANDSETS DIVISION TELECOMMUNICATION EQUIPMENT & HANDSET COMPANY 459-9, Kasan-dong, Kumchon-gu, Seoul 153-023, Korea Phone : +82-2-850-3860, +82-2-818-4272,4676 FAX : +82-2-850-3855 Mobile Phone : +82-11-756-7160 E-mail : [email protected] --------------------------------------------------- ---------- ?? ??? ---------- ??? : Helen Zhao <[email protected]> ??? : CDMA?)QE?? ??? ??([email protected], 82-2-850-3860) ? ? : 04/1/31 7:55:04 AM ? ? : FW: LG Elect. Assessment No: AN04T3617 FCC ID: BEJRD5130 Hello Cheol-Goo, Below are the questions from our reviewer, Mr. Chris Harvey regarding your LG-RD5130 application. Please kindly respond to them asap. You can either reply directly to Mr. Harvey or send to me then I forward to him. 1) Please provide the Emission Designator with a justification explanation for this application (it is likely to be 1M25F9W for CDMA operation). [Helen Zhao] You may need provide 99% bandwidth measurements. 2) It appears as though the internal photographs provided contain areas of the PC Board that remain covered by RF shields. Please submit photographs with the shields removed per FCC requirements. [Helen Zhao] Attached is the Internal Photos that were extracted from your test report - Appendix C and submitted to TCB review. Please retake the internal photos with the shields removed. Thanks. For your information, below is our reviewer's contact information: Chris Harvey [email protected] 443-622-3300 Thank you! Hele…

Text truncated - open the document above for the full version.

FCC ID : BEJRD5130 YVG^ 1. External View FCC ID : BEJRD5130 ZVG^ FCC ID : BEJRD5130 [VG^

PROPOSED FCC ID LABEL AND LOCATION LG ELECTRONICS INC. This device complies with Part 22 of the FCC Rules. FCC ID Label

FCC ID : BEJRD5130 \VG^ 2. Internal View FCC ID : BEJRD5130 ]VG^ FCC ID : BEJRD5130 ^VG^

ᄌᦝጁᱧ 㧯㨔㨍㨚㨓㨑ޓ㧴㨕㨟㨠㨛㨞㨥 ᄌᦝጁᱧ 㧯㨔㨍㨚㨓㨑ޓ㧴㨕㨟㨠㨛㨞㨥 6[RG0Q559ޓ# 559#559# 559# 5RGEKHKECVKQP5JGGV0Q ޓޓޓ⇟ 0Q ᄌᦝ &CVG ᄌ ᦝ ౝ  %QPVGPVUQH%JCPIG 2003.03.06 Constitution  559
  
    6ޓJKUURGEKHKECVKQPKUCRRNKECDNGVQ%JKR6[RG#PVGPPCECTTKGFKPVJGEGNNWNCTRJQPGVGTOKPCNQH 5KPING$CPF %&/#  ޓᧄ઀᭽ᦠߪ 5KPING$CPF #/&% ߩ៤Ꮺ㔚⹤┵ᧃᯏߦ៞タࠆࠇߐ %JKR6[RG#PVGPPC ߡ޿ߟߦㆡ↪ޕࠆߔ

  559ޓ#
 5ޓ+WPKVYKNNDGWUGFWPNGUUCP[URGEKCNKVKGUCTGCPPQWPEGF ޕࠆߔ૶↪ࠍන૏ +5ޔࠅ㒢޿ߥ߇⺑᣿ߥ೎.ޓ           ! $CPF Ꮺၞ඙ಽ 6:4: (TGSWGPE[ ๟ᵄᢙ 㨪/*\ 㨪/*\ 
"  0ޓQOKPCN+ORGFCPEG㧦ǡ ޓၮḰ୯㧦ǡ  #$%  8594ޓQRVKOK\CVKQPKURGTHQTOGFD[OCVEJKPIEKTEWKVKPCEVWCNEGNNWNCTRJQPG ޕࠆߔᦨㆡൻࠅࠃߦ㩙㨹㩋㩧㩂㩨࿁〝ߪ 8594 ߡ޿߅ߦታᯏޓ   #$%     !"#$#$% 8594ޓUCVKUHKGUVJGHQNNQYKPIVCDNGEJCTCEVGTKUVKE/CVEJKPIEKTEWKVUJQYPKP(KIKUWUGF ޕࠆߔ૶↪ࠍߩ߽ߔ␜ߦ KI( ߪ㩙㨹㩋㩧㩂㩨࿁〝ޕࠆߔߣߣߎߔߚḩࠍᕈ.ߩਅ⴫ߪ 8594ޓ (TGSWGPE[$CPF ๟ᵄᢙᏪ 㨪/*\㨪/*\ 8594 6.8nH 1.5pF Fig 3.3.1 Matching circuit  559  
&!  #$%     !"#$#$%% 8594ޓKUOGCUWTGFCVUVCPFCTFDQCTFUJQYPKP(KI ޕࠆࠇߐ᷹ቯߡ޿߅ߦᮡḰၮ᧼ߔ␜ߦ KI( ߪ 8594ޓ  '"  ' &   ()  *     !"#$+,-./012&'( (TGSWGPE[$CPF ๟ᵄᢙᏪ 㨪/*\㨪/*\ )CKP 㩃㩨㨼㩧 F$KF$K 1.65 2 3 4.8 117.7 99.6100 35 34.6 3.2 12.2 Fig 3.3.2 Standard board Coaxial cable Antenna SSW0900 Microstrip line Matching circuit GND area 99.6*34.6mm  559  '
&!  %  ( )*3,4-2% ޓ%QQTFKPCVGUCPF/GCUWTGOGPVRNCPGCVTCFKCVKQPRCVVGTPOGCUWTGOGPVCTGFGHKPGFKP(KI C CPF(KI D 4CFKCVKQPRCVVGTPOGCUWTGOGPVKURGTHQTOGFCVOQTGVJCPHTGSWGPEKGUKPENWFKPI VJGJKIJGUVCPFNQYGUVNKOKVHTGSWGPE[QHVJGDCPF ޓ᡼኿㩔㩩㩊㨺㩧ߩ᷹ቯޔߡ޿߅ߦᐳᮡ♽ߣ᷹ቯ㕙ߪ (KI C ෸߮ (KI D ࠅࠃߦቯ⟵ޕࠆࠇߐ᡼኿㩔㩩 ޕࠆߔ᷹ቯߢ๟ᵄᢙߩએ਄ߟ㧞ޔ߻฽ࠍ਄ਅ㒢๟ᵄᢙߩ૶↪Ꮺၞߪ㩊㨺㩧 E2 CW (c) Z Y X Fig 3.4.2(a) Coordinates H CW (a) E1 CW (b) Fig 3.4.2(b) Measurement Plane  559  5(6% 7  5 &8  (6% 7&+ ,-. ޓ9 OKP9%࡮  5
! 7(6% 7 ,-./0 +ޓVKUPGEGUUCT[VQIGPGTCVGPQRTQDNGOQPCPVGPPCCRRGCTCPEGCHVGTNQCFKPIVJGGNGEVTKERQYGT QH9VQVJGHGGFKPIRQKPVCVVJGTQQOVGORGTCVWTGFWTKPIOKPWVGU#PFKVKUPGEGUUCT[VQUCVKUH[ VJGTGSWKTGOGPVUUJQYPKPCPF ޓቶ᷷ߢ㧡ಽ㑆㨻㩧㩍㩏ߩ⛎㔚ὐߦ⹜㛎ᓟޔߟ߆ޕ޿ߥࠄߥߪߡߓ↢ࠍਇౕวߦᄖⷰޔᓟߚߒශടࠍ㔚ജߩ 9 ޕ޿ߥࠄߥߪߡߊߥߐߚḩࠍ㔚᳇⊛ⷐ᳞ߩ  ߮෸  ߽ '"!   9*  ! 12 ' : ! 3456 ޓ&KOGPUKQPHQNNQYUVJGHQNNQYKPIHKIWTG ޕ߁ᓥߦਅ࿑ߪᄖᒻኸᴺޓ ޓ(KIޓ&KOGPUKQPᄖᒻኸᴺ 16.4 r 0.25 17.4 r 0.25 1 r 0.1 1 r 0.1 4.8 r 0.15 1.5 r 0.15 2 r 0.2 2 r 0.2 0.2 r 0.1 2KP(GGFKPI 2KP0%  559 5;  (78 5  9 79:;<=/0 Ԙ(KTUVN[NGCXKPICPCPVGPPCVQVJGVGORGTCVWTG6 .1 HQTJQWT ԙ5GEQPFN[VJGCPVGPPCKUNGHVVQVJGVGORGTCVWTGQH6 *1 D[UCOGOGVJQFHQTJQWT E[ENGUQHVJKUQRGTCVKQP TGHGTVQ(KI CTGVQDGTGCRGCVGF㧔4GNCVKXGJWOKFKV[OWUVDG OCKPVCKPGF㧕#HVGTVJGCDQXGE[ENGVGUVVJGCPVGPPCOWUVPQVJCXGCPQWVGTFCOCIGCPFCNUQ KVOWUVRCUUTGSWKTGOGPVUUJQYPKPCPF 6 ᤨ㑆  ࠍ࠽࠹ࡦࠕޓ .1 6 ᤨ㑆  ߢᣇᴺߓหޔᓟߚߒ᡼⟎ߦ᷷ᐲߩ *1 )d(ᆑߩߎޕࠆߔ᡼⟎ߦ᷷ᐲߩ㧔(KI ⹜㛎ᓟޕ ࠆߔ⛽ᜬࠍ㧑 ߪ⋧ኻḨᐲޔߒૉ ࠆߔታᣉߡߒ㄰ࠅ➅ࠍ࡞ࠢࠗࠨ  ߡߒߦ࡞ࠢࠗࠨ  ࠍ ෳᾖ ޕ޿ߥࠄߥ߫ࠇߌߥߐߚḩࠍⷐ᳞੐㗄ࠆࠃߦ  ߮෸  ߟ߆ޔߊߥ߇៊்ߥᄖⷰ⊛߽ߦ &KURNC[ ⴫␜ FKXKUKQP ඙ಽ VGORGTCVWTG ᷷ᐲ 6 .1 .QYGTVGORGTCVWTGE[ENKPI ૐ᷷ %[ENKPI ͠ 6 *1 *KIJGTVGORGTCVWTGE[ENKPI 㜞᷷ %[ENKPI ͠ (KIޓ6GORGTCVWTGE[ENKPIޓ᷷ᐲ %[ENKPI ͠ 6 *1 6 .1 6GOR͠ 㧴㨞㧴㨞㧴㨞㧴㨞 %;%.' 6+/'*1745  559 5
<   ! =  !  >>9>?/0 6JGCPVGPPC UEJCTCEVGTKUVKEUCTGVQDGOGCUWTGFCHVGTNGCXKPIKVKPVJGDCVJHQTJQWTUWPFGT EQPFKVKQPUJQYPDGNQY#HVGTVJGCDQXGVJGCPVGPPCOWUVPQVJCXGCPQWVGTFCOCIGCPFCNUQKVOWUV RCUUTGSWKTGOGPVUUJQYPKPCPF  ߦᕡ᷷ᕡḨᮏߢ᧦ઙߩਅࠍ࠽࠹ࡦࠕޓ៊்ߥᄖⷰ⊛߽ߦ⹜㛎ᓟޕࠆߔ᷹ቯࠍᕈ.ߩߘޔᓟߚߒᤨ㑆᡼⟎ ޕ޿ߥࠄߥ߫ࠇߌߥߐߚḩࠍⷐ᳞੐㗄ࠆࠃߦ  ߮෸  ߟ߆ޔߊߥ߇ 6GORGTCVWTG ᷷ᐲ 4GNCVKXGJWOKFKV[ ⋧ኻḨᐲ 6GUVKPIVKOG ⹜㛎ᤨ㑆 r͠r㧑r㧴㨞 5   7 ! @A9:/0 1ޓRGTCVKPIVGORGTCVWTGTCPIG㧦͠㨪 ͠ 㧑KPTGNCVKXGJWOKFKV[ 9ޓJGPQRGTCVKPIKPVJGCDQXGOGPVKQPGFVGORGTCVWTGTCPIGVJGCPVGPPCOWUVPQVJCXGCPQWVGTFCOCIG CPFCNUQKVOWUVRCUUTGSWKTGOGPVUUJQYPKPCPF ޓേ૞᷷ᐲ⹜㛎▸࿐㧦͠㨪 ͠ ⋧ኻḨᐲޓ㧑 ߌߥߐߚḩࠍⷐ᳞੐㗄ࠆࠃߦ  ߮෸  ߟ߆ޔߊߥ߇៊்ߥᄖⷰ⊛ޔേ૞ᤨߩߢ᷷ᐲ▸࿐ߩ਄⸥ޓ ޕ޿ߥࠄߥ߫ࠇ 5 ' 7 ! BC9:/0 6ޓJG5VQTCIG6GORGTCVWTG6GUVJCUGZRGTKOGPVU ޓ(KTUVCNQYVGORGTCVWTGUVQTCIGVGUVYKNNDGGZCOGF#HVGTNGCXKPICPVGPPCCV͠HQTJQWTU KVYKNNDGKPCTQQOVGORGTCVWTGHQTJQWTU ޓ#JKIJVGORGTCVWTGUVQTCIGVGUVYKNNDGGZCOGF#HVGTNGCXKPIKVCV͠UKOKNCTN[HQTJQWTU KVYKNNDGNGHVKPCTQQOVGORGTCVWTGHQTJQWTU ޓ'CEJGZCOKPCVKQPKURGTHQTOGFWPFGTVJGGPXKTQPOGPVQHQHTGNCVKXGJWOKFKV[ ޓ#HVGTVJGCDQXGVJGCPVGPPCOWUVPQVJCXGCPQWVGTFCOCIGCPFCNUQKVOWUVRCUUTGSWKTGOGPVU UJQYPKPCPF ޕࠆࠇࠄߌಽߦ㜞᷹᷷ቯૐ᷷ߪ᷷ᐲ臣⬿⹜㛎ޓ ޕ߁ⴕߦᓟߚߒᤨ㑆᡼⟎  ߢᏱ᷷ޔᓟߚߒᤨ㑆᡼⟎  ߢ͠ޔߪૐ᷷臣⬿⹜㛎ߕ߹ޓ ޓ㜞᷷臣⬿⹜㛎ߪห᭽ ߦ͠ ߢ ᤨ㑆᡼⟎ߚߒᓟޔᏱ᷷ ߢ ᤨ㑆᡼⟎ߚߒᓟߦⴕޕ߁ ޕ߁ⴕߢਅߩ⋧ኻḨᐲߩ㧑 ߽ࠇߕ޿ߪ⹜㛎 ࠇߌߥߐߚḩࠍⷐ᳞੐㗄ߥ㔚᳇⊛ࠆࠃߦ  ߮෸  ߟ߆ޔߊߥ߇៊்ߥᯏ᪾⊛߮ᄖⷰ෸ޔ⹜㛎ᓟޓ ޕ޿ߥࠄߥ߫  559 5 5#   ! D@/0 ޓ$GHQTGXKDTCVKQPVGUVVJGCPVGPPC UGNGEVTKECNEJCTCEVGTKUVKEPGGFUVQDGOGCUWTGF ޓ#HVGTVJGCDQXGUVGRCPCPVGPPCYKNNDGCVVCEJGFVQCXKDTCVKQPVGUVGSWKROGPV 6ޓJGXKDTCVKQPVGUVYKNNDGECTTKGFQWVHQTJQWTKPVJGFKTGEVKQPUQH:;CPF<WPFGTEQPFKVKQP UJQYPDGNQY ޓ#HVGTVJGCDQXGVJGCPVGPPCOWUVPQVJCXGCPQWVGTFCOCIGCPFCNUQKVOWUVRCUUTGSWKTGOGPVU UJQYPKPCPF ޕࠆߡ┙ߺ⚵ࠍ࠽࠹ࡦࠕߦ⹜㛎ⵝ஻ޔᓟߚߒ᷹ቯࠍᕈ.㔚᳇⊛ߩ࠽࠹ࡦࠕߦ೨ߩ⹜㛎ޓ:; ߩᣇะߦฦޘ ⷐߥ㔚᳇⊛ࠆࠃߦ  ߮෸  ߟ߆ޔߊߥ߇៊்ߥᯏ᪾⊛߮ᄖⷰ෸ޔ⹜㛎ᓟޕࠆߔታᣉࠍᤨ㑆⹜㛎  ޕ޿ߥࠄߥ߫ࠇߌߥߐߚḩࠍ᳞੐㗄 1UEKNNCVKPIHTGSWGPE[ ᝄേ๟ᵄᢙ 5YGGR6ޓKOG ᝹ᒁᤨ㑆 CORNKVWFG ᝄ᏷ 6JGOCZKOWOCEEGNGTCVKQP ᦨᄢടᄕᐲ 㨪*\ ಽOOI  559 ?() 7   EFGH  559 @%: IJKL @ &"<9<%A#$%%(< @
<(%        (TGSWGPE[ )*\ 8594 (TGSWGPE[ …

Text truncated - open the document above for the full version.

1/1 Report No.: 00431-4529-C4006 LG Electronics Inc. Q & R Center, 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul, Korea Tel:+82-2-2630-3077~9, Fax:+82-2-2635-5543 LG Electronics Inc. Quality & Reliability Center 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul 150-096, Korea Tel: + 82 2 2630 3077~9, Fax: +82 2 2635 5543 CERTIFICATION OF COMPLIANCE Date of Issue: January 20, 2004 Test Report No: 00431-4529-C4006 Applicant: LG Electronics Inc. Regulation: FCC Part 22 , Part2 Test procedure: ANSI C63.4-2001, TIA/EIA603 Equipment Class: Intentional Radiators EUT Type: Single Band, Single Mode CDMA Mobile Phone FCC ID: BEJRD5130 Trade Name(s): Model No.: LG LG-RD5130 This device has been verified to comply with the applicable requirements in the FCC Part 22 & Part2 and was tested in accordance with the measurement procedures specified in ANSI C63.4- 2001, TIA/EIA 603. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Kyeom-Soon Kim / General Manager Quality and Reliability Center LG Electronics Inc. 2/2 Report No.: 00431-4529-C4006 LG Electronics Inc. Q & R Center, 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul, Korea Tel:+82-2-2630-3077~9, Fax:+82-2-2635-5543 REPORT FOR AN INTENTIONAL RADIATORS U.S. Responsible Party: Address: LG Electronics USA Inc. 6133 North River Road, Suite 1100 (Riverway Plasza) Rosemont, IL 60018, USA Contact Person: P. H. Byun, General Manager Telephone No.: (847) 692-4630 EXT.329 Manufacturer: LG Electronics Inc. Address: 459-9, Kasan-Dong, Kunchon-Gu, Seoul, 153-023, Korea FCC ID No.: BEJRD5130 EUT Class: Intentional Radiators EUT Type: Single Band, Single Mode CDMA Mobile Phone Trade Name: LG Model No.: LG-RD5130 Rule Part: FCC Part 22, Part2 Test Procedure: ANSI C63.4-2001, TIA/EIA603 Date of Test: January 5 ~ 16, 2004 Date of Receipt of EUT: January 5, 2004 Date of Issue: January 20, 2004 Test Report No.: 00431-4529-C4006 Test Result: Positive Quality and Reliability Center authorizes the above-named applicant to reproduce this report provided it is reproduced in its entirety. Quality and Reliability Center reports apply only to the specific samples tested under stated test conditions. It is the manufacturer’s responsibility to assure that additional production unit of this model are manufactured with identical electrical and mechanical components. This report is the confidential property of the client. As a mutual protection to our clients, the public and ourselves, extracts from the test report shall not be reproduced except in full without our written approval. Tested by: Reviewed by: Y. S. Lee / Senior Research Engineer Quality and Reliability Center LG Electronics Inc. J. C. Lee / Senior Research Engineer Quality and Reliability Center LG Electronics Inc. 3/3 Report No.: 00431-4529-C4006 LG Electronics Inc. Q & R Center, 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul, Korea Tel:+82-2-2630-3077~9, Fax:+82-2-2635-5543 CONTENTS Page 1. GENERAL INFORMATION ..................................................................................................................... 4G 1.1 D ESCRIPTIONS OF EQUIPMENT UNDER TEST (EUT)................................................................................... 4G 1.2 R EGULATIONS APPLIED TO EUT ............................................................................................................... 4G 1.3 M EASUREMENT PROCEDURE.................................................................................................................... 4G 1.4 M EASUREMENT PLACE............................................................................................................................. 4G 2. TEST SITE ................................................................................................................................................... 4G 2.1 S EMI-ANECHOIC CHAMBER....................................................................................................................... 4G 2.2 A SHIELDED ENCLOSURE.......................................................................................................................... 4G 3. CALIBRATIONS OF MEASURING INSTRUMENTS .......................................................................... 5G 4. DESCRIPTION OF TEST CONDITION .................................................................................................. 5G 4.1 RF P OWER OUTPUT.................................................................................................................................. 5G 4.2 M ODULATION CHARACTERISTICS............................................................................................................. 7G 4.3 O CCUPIED BANDWIDTH............................................................................................................................ 8G 4.4 S PURIOUS EMISSION AT ANTENNA TERMINAL.......................................................................................... 9G 4.5 F IELD STRENGTH OF SPURIOUS RADIATION.............................................................................................. 9G 4.6 F REQUENCY STABILITY.......................................................................................................................... 11G 5. TEST DATA ............................................................................................................................................... 12G 5.1. RF P OWER OUTPUT (§2.1046) .............................................................................................................. 12G 5.2. M ODULATION CHARACTERISTICS (§2.1047) ......................................................................................... 13G 5.3. O CCUPIED BANDWIDTH (§2.1049) ........................................................................................................ 13G 5.4. S PURIOUS EMISSION AT ANTENNA TERMINAL (§2.1051) ........................................................…

Text truncated - open the document above for the full version.

XVGXZ FCC ID : BEJRD5130 APPENDIX A : Test Graph 1. Conducted Output Power 2. Occupied Bandwidth 3. 26 dB Emission Bandwidth 4. Band Edge 5. Out of Band Emission 6. CDMA Mobile Emission in Base Frequency Range YVGXZ FCC ID : BEJRD5130 1. Conducted Output Power 1.1 Low Channel 1.2 Middle Channel ZVGXZ FCC ID : BEJRD5130 1.3 High Channel [VGXZ FCC ID : BEJRD5130 2. Occupied Bandwidth 2.1 Low Channel 2.2 Middle Channel \VGXZ FCC ID : BEJRD5130 2.3 High Channel ]VGXZ FCC ID : BEJRD5130 3. 26 dB Emission Bandwidth 3.1 Low Channel 3.2 Middle Channel ^VGXZ FCC ID : BEJRD5130 3.3 High Channel _VGXZ FCC ID : BEJRD5130 4. Band Edge 4.1 Low Channel 4.2 High Channel `VGXZ FCC ID : BEJRD5130 5. Out of Band Emission 5 .1 Low Channel XWVGXZ FCC ID : BEJRD5130 5.2 Middle Channel XXVGXZ FCC ID : BEJRD5130 5.3 High Channel XYVGXZ FCC ID : BEJRD5130 6. CDMA Mobile Emission in Base Frequency Range 6.1 Low Channel 6.2 Middle Channel XZVGXZ FCC ID : BEJRD5130 6.3 High Channel

FCC ID : BEJRD5130 XVG\ APPENDIX B : 1. Conducted Output Power 2. Radiated Output Power / Radiated Spurious Emission 3. Occupied Bandwidth / 26 dB Emission Bandwidth 4. Band Edge 5. Out of Band Emission 6. CDMA Mobile Emission in Base Frequency Range 7. Frequency Stability Test Set-up Photographs FCC ID : BEJRD5130 YVG\ 1. Conducted Output Power 2. Radiated Output Power / Radiated Spurious Emission FCC ID : BEJRD5130 ZVG\ 3. Occupied Bandwidth / 26 dB Emission Bandwidth 4. Band Edge FCC ID : BEJRD5130 [VG\ 5. Out of Band Emission 6. CDMA Mobile Emission in Base Frequency Range FCC ID : BEJRD5130 \VG\ 7. Frequency Stability