BEJWCP500Wireless Charging Pad

English Español Rev1.0 US All rights reserved. LG Electronics inc., 2012 Note: For optimal performance and to prevent any damage to, or misuse of the WCP-500, please read all the information carefully before using the WCP-500. Any modifications or changes to this manual due to typographical errors or inaccuracies of stated information shall only be made by LG Electronics Inc.. LG Electronics Wireless Charging Pad WCP-500 User Manual English Español All rights reserved. LG Electronics inc., 2012 Note: For optimal performance and to prevent any damage to, or misuse of the WCP-500, please read all the information carefully before using the WCP-500. Any modifications or changes to this manual due to typographical errors or inaccuracies of stated information shall only be made by LG Electronics Inc.. LG Electronics Wireless Charging Pad WCP-500 User Manual ENG 1 Included in Package WCP-500 (Wireless Charging Pad) Power SupplyWarranty CardUser Manual Description of parts Charging Area Charging Status LED Indicator Power LED Indicator ENG 2 - When the power supply is connected, the wireless charging pad (WCP-500) will turn on. The power Indicator will show a solid blue light. - When a Wireless Charging Enabled Device is placed in the correct position, the Charging status LED indicator will change from solid orange to flickering green. - When charging is completed, the Charging status LED indicator will show a solid green light. How to use Charging ENG 3 Function WCP-500 Status Action Power LEDCharging status LED Operating Power supply disconnected OffOff Power supply connectedSolid BlueSolid Orange Charging ChargingSolid BlueFlickering Green Charging completeSolid BlueSolid Green Charging Stopped (Wired phone charger is attached at the same time) Solid BlueSolid Orange Error If the internal temperature of the charger exceeds 80 degrees (°C) Solid BlueSolid Red Other Fault States (WCP-500 or Phone) LED display - Do not drop the Wireless charging pad from high places. - Do not modify, repair, or take the Wireless charging pad apart. - Do not clean with water alcohol or benzene. - Keep the Wireless charging pad away from humidity & dust. - Do not place heavy objects on the Wireless charging pad. Precautions ITEMDescription Input / OutputDC 5.2V, 2000mA / DC 5V, 1000mA Charging time< 4 hours (Based on 2150mAh Battery) Operation temperature-10°C ~ 60°C Dimension / Weight170 (L) x 94 (W) x 11.5 (T) (mm)/136g ENG 4 FCC NOTICE TO USERS: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Declaration of confirmation FCC ID: BEJWCP500 ENG 5 - When disconnecting the power supply, always remove with the plug, do not pull the wire by itself. - Never handle the power plug with wet hands, as this could cause fire or electric shock. - Refer servicing to qualified personnel only. - Do not open the housing - Do not twist or pinch the power supply cord. If the plugs or power supply cords need to be replaced, ensure that they comply with the manufacturer’s recommendation. - Unplug the device during lighting storms and when unused for extended periods of time. When using an electrical device, especially when children are present, basic safety precautions should always be followed, including the following: DANGER to reduce the risk of electric shock - Always unplug the device from the electrical outlet before cleaning. - Do not reach for a device that has fallen into water. Unplug it immediately. - Do not place or store device where it can fall or be pulled into a tub or sink. - Do not place in or drop into water or other liquid. WARNING to reduce the risk of burns, fire, electric shock or injury to persons - Do not use with extension cord. - Children should be closely supervised to ensure that they do not play with the device. - Use this device only for its intended use as described in this manual. Do not use with unauthorized accessories of devices. - Never operate this device if it has a damaged cord, plug, cable or housing. If it is not working properly, if it has been dropped or damaged, return it to the LG Service Center for examination and repair. - Keep cord away from heated surfaces. - This device is designed for indoor use only. Do not use outdoors. - Only set on dry surfaces. Do not place on surface wet from water or cleaning solvents. Safety Instructions

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: October 12, 2012 Letter of Authorization We, the undersigned, hereby authorize Digital EMC Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCCID: BEJWCP500 including signing of all documents relating to these matters. Any and all acts carried out by Digital EMC Co., Ltd. on our behalf shall have the same affect as acts of our own. Sincerely, Jacob Cho Director, Standards & Compliance

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: October 12, 2012 C omp liance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards;

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: October 12, 2012 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: BEJWCP500 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description File name PERMANENT 1 Block Diagram Block Diagram_BEJWCP500.pdf 2 Operational Description Operational Description_ BEJWCP5000.pdf 3 Schematics Schematic_ BEJWCP500.pdf 4 Part Lists Part List_ BEJWCP500.pdf SHORT-TERM 5 External Photos Ext Photo_ BEJWCP500.pdf 6 Internal Photos Int Photo_ BEJWCP500.pdf 7 Test-Setup Photos Test Photo_ BEJWCP500.pdf 8 Users Manual User Manual_ BEJWCP500.pdf Note: The pictures on the label location do not require any long term or short term confidentiality. The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Jacob Cho Director, Standards & Compliance

FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 1 FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 2 FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 3 FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 4

FCC ID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. Refer to next page. Note 1. The FCC label shown is representative of the label that will appear on the radio when in production. Note 2. The 15.19 statement request is placed in a prominent location in the user`s manual.

FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 1 FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 2 FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 3 FCCID: BEJWCP500 Copyright Ⓒ 2012, Digital EMC Co., Ltd. View 4

DEMC1207-01102 DRTFCC1209-0453(1) TRF-RF-308(01)100709 Page 2 / 7 Copyright ○ C 2012, Digital EMC Co., Ltd. Test Report Version Test Report No. Date Description DRTFCC1209-0453 Sep. 05, 2012Final version for approval DRTFCC1209-0453(1) Dec. 10, 2012Additional description of operating and detector mode DEMC1207-01102 DRTFCC1209-0453(1) TRF-RF-308(01)100709 Page 3 / 7 Copyright ○ C 2012, Digital EMC Co., Ltd. CONTENTS 1. Equipment information ............................................................................. 4 1.1 Equipment description ............................................................................ 4 1.2 Ancillary equipment ................................................................................. 4 2. Information about test items .................................................................... 5 2.1 Operating mode ...................................................................................... 5 2.2 Auxiliary equipment ................................................................................. 5 2.3 Test Configuration ................................................................................... 5 2.4 Tested environment ................................................................................. 5 3. E and H field strength ............................................................................... 6 DEMC1207-01102 DRTFCC1209-0453(1) TRF-RF-308(01)100709 Page 4 / 7 Copyright ○ C 2012, Digital EMC Co., Ltd. 1. Equipment information 1.1 Equipment description FCC Equipment Class Part 15 Low Power Transmitter Below 1705 kHz (DCD) Equipment type Wireless Charging Pad Equipment model name WCP-500 Equipment add model name N/A Equipment serial no. Identical prototype Frequency range 110 ~ 200 kHz Charging power range 0 ~5 W Protocol Note 1 WPC protocol(A1 type) Communication mode Note 2 Analog ping mode, Digital communication mode Power AC-DC Adaptor: AC 120 V 60 Hz Antenna type Internal Loop Antenna(Circular coil) Note 1: This device can charge only one client device on the specific location at a time. So this device is a A1 device of the WPC protocol Note 2: Description of communication mode, - Analog/Digital ping mode In order to find a client device, this device applies a short pulse to its primary coil regularly. This device can know the presence of client device on this device through monitoring its primary coil current. - Digital communication mode After finding client device, this device initiates power signal and then receives data PACKETS from the client device according to the WPC protocol. If the client device is removed on the top of this device then this communication is stopped at once and the transmitting power signal of this device is immediately stopped and this device goes to IDLE MODE. The power signal of this device shall be used for both communicating data packets form the client device and charging. 1.2 Ancillary equipment Equipment Model No. Serial No. Manufacturer Note Adapter PSTA-D01WT TA250000013 LG Electronics - - - - - - DEMC1207-01102 DRTFCC1209-0453(1) TRF-RF-308(01)100709 Page 5 / 7 Copyright ○ C 2012, Digital EMC Co., Ltd. 2. Information about test items 2.1 Operating mode Operating Mode 1 Charging and communication mode Continuously transmission mode Note: Based on the part 15 test results, the emissions of the analog ping mode are lower than the charging and communication mode. So RF exposure test is performed only with the charging and communication mode. 2.2 Auxiliary equipment Equipment Model No. Serial No. Manufacturer Note Client Device (rectangular coil) WCC-920-REV03 N/A LG Electronics Inc. - Note: This client device was supported by manufacturer. And they declared that the client device will be installed in mobile phones for charging the phone. 2.3 Test Configuration This device has been tested with various resistors to simulate the various load conditions of the client device. The charging current was controlled from 0 mA (Min) to 1000 mA (MAX) by 100 mA step using the resistors and two types of client device with rectangular coil. Charging current TM-X Series 0mA TM-X-0 100mA TM-X-1 200mA TM-X-2 300mA TM-X-3 400mA TM-X-4 500mA TM-X-5 600mA TM-X-6 700mA TMX-7 800mA TM-X-8 900mA TM-X-9 1000mA TM-X-10 Note 1: The client device and load resistor shall be placed on the EUT`s chargeable area especially center or near surrounding center. so the client device is placed on the center and 4 positions of near surrounding center where can be charged. Above “X” means position of the client device on the EUT’s chargeable area as below. C : Center of the Charging area / T : Top Side of the Charging area B: Bottom Side of the Charging area / R: Right Side of the Charging area L : Left Side of the Charging area Refer to test setup photo for more details. 2.4 Tested environment Temperature : 22 ~ 23 o C Relative humidity content : 46 ~ 48 % R.H. Details of power supply :AC 120V 60Hz DEMC1207-01102 DRTFCC1209-0453(1) TRF-RF-308(01)100709 Page 6 / 7 Copyright ○ C 2012, Digital EMC Co., Ltd. 3. E and H field strength For RF exposure purposes, the E and H field strengths are measured separately with E and H probes and meters at different locations surrounding the test setup. - Test setup diagram Note 1: Measurement distance = 5 cm Note 2: Test were performed above A, B, C, D probe positions. Note 3: The probe height(H) is varied to maximize the emission. Note 4: Detector mode of probe = Peak for E-field measurement RMS for H-Field measurement - Measurement data: refer to the next page - Test equipment list Type Manufacturer Model Cal.Date (yy/mm/dd) Next. Cal. Date (yy/mm/dd) S/N Exposure level meter NARDA ELT-400 12/01/30 13/01/30 J-0015 Magnetic Field Meter Holaday Industries HI-3627 11/02/14 13/02/14 00023776 DEMC1207-01102 DRTFCC1209-0453(1) TRF-RF-308(01)100709 Page 7 / 7 Copyright ○ C 2012, Digital EMC Co., Ltd. Measurement data 1. E field test results Te s t S t e p Te s t configuration Probe Height (cm) Pr…

Text truncated - open the document above for the full version.

TCB Review comments: As the 20dB bandwidth measurement is to confirm that the signal remains within the allocated band, as the device complied when measured using a bandwidth wider than necessary there was no need to repeat with a narrower bandwidth.The lab has been advisedthat they should follow the guidance/requirements of ANSI C63 for bandwidth measurements.

DEMC1207-01102 DRTFCC1209-0452(1) TRF-RF-204(01)110221 Page 2 / 16 Copyright ○ C 2012, Digital EMC Co., Ltd. Test Report Version Test Report No. Date Description DRTFCC1209-0452 Sep. 05, 2012Final version for approval DRTFCC1209-0452(1) Dec. 10, 2012Modification of Bandwidth result DEMC1207-01102 DRTFCC1209-0452(1) TRF-RF-204(01)110221 Page 3 / 16 Copyright ○ C 2012, Digital EMC Co., Ltd. CONTENTS 1. Equipment information .............................................................. 4 1.1 Equipment description ............................................................. 4 1.2 Ancillary equipment ................................................................. 4 2. Information about test items ..................................................... 5 2.1 Operating mode ....................................................................... 5 2.2 Test mode ................................................................................ 5 2.3 Auxiliary equipment ................................................................. 5 2.4 Tested environment ................................................................. 5 2.5 EMI Suppression Device(s)/Modifications ............................... 5 3. Test Report ................................................................................. 6 3.1 Summary of tests .................................................................... 6 3.2 Transmitter requirements ........................................................ 7 3.2.1 20dB Bandwidth Measurement ........................................... 7 3.2.2 Radiated Emissions ............................................................ 8 3.2.3 AC Line Conducted Emissions .......................................... 10 APPENDIX I................................................................................... 15 DEMC1207-01102 DRTFCC1209-0452(1) TRF-RF-204(01)110221 Page 4 / 16 Copyright ○ C 2012, Digital EMC Co., Ltd. 1. Equipment information 1.1 Equipment description FCC Equipment Class Part 15 Low Power Transmitter Below 1705 kHz (DCD) IC Category Equipment Category I Equipment Equipment type Wireless Charging Pad Equipment model name WCP-500 Equipment add model name N/A Equipment serial no. Identical prototype Power AC-DC Adaptor: AC 120V 60Hz Antenna type Internal Loop Antenna(Circular coil) 1.2 Ancillary equipment Equipment Model No. Serial No. Manufacturer Note Adapter PSTA-D01WT TA250000013 LG Electronics - - - - - - DEMC1207-01102 DRTFCC1209-0452(1) TRF-RF-204(01)110221 Page 5 / 16 Copyright ○ C 2012, Digital EMC Co., Ltd. 2. Information about test items 2.1 Operating mode Operating Mode 1 (OP 1) Charging and DATA packet communication mode Continuously transmission mode Operating Mode 2 (OP 2) Analog/Digital ping mode(Transmitting a short pulse to find a client device) Non continuously transmission mode 2.2 Test mode This device has been tested below conditions: Charging current TM-X Series 0mA TM-X-0 100mA TM-X-1 200mA TM-X-2 300mA TM-X-3 400mA TM-X-4 500mA TM-X-5 600mA TM-X-6 700mA TMX-7 800mA TM-X-8 900mA TM-X-9 1000mA TM-X-10 Note 1.: “X” = Positions of client device on the DUT(Refer to test setup photo.) (C = Center, T = Top, B= Bottom, L = Left, R= Right) 2.3 Auxiliary equipment Equipment Model No. Serial No. Manufacturer Note Client Device (rectangular coil) WCC-920-REV03 N/A LG Electronics Inc. - Note: This client device was supported by manufacturer. And they declared that the client device will be installed in mobile phones for charging the phone. 2.4 Tested environment Temperature : 23 ~ 26 o C Relative humidity content : 46 ~ 57 % R.H. Details of power supply :AC 120V 60Hz 2.5 EMI Suppression Device(s)/Modifications EMI suppression device(s) added and/or modifications made during testing → None DEMC1207-01102 DRTFCC1209-0452(1) TRF-RF-204(01)110221 Page 6 / 16 Copyright ○ C 2012, Digital EMC Co., Ltd. 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Test Condition Status Note 1 Test Items 2.1049 Occupied Bandwidth Radiated C 15.209 Radiated Emission C 15.207 AC Conducted Emissions AC Line Conducted C Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable The sample was tested according to the following specification: ANSI C-63.4-2003, RSS-GEN Issue 3 DEMC1207-01102 DRTFCC1209-0452(1) TRF-RF-204(01)110221 Page 7 / 16 Copyright ○ C 2012, Digital EMC Co., Ltd. 3.2 Transmitter requirements 3.2.1 20dB Bandwidth & Occupied Bandwidth Measurement - Procedure: The 20dB bandwidth and occupied bandwidth(99% emission bandwidth) are measured with a spectrum analyzer connected via a receiving antenna placed near the EUT while the EUT is operating. - Measurement Data: ▪ Operating Mode 1 ▪ Operating Mode 2 DEMC1207-01102 DRTFCC1209-0452(1) TRF-RF-204(01)110221 Page 8 / 16 Copyright ○ C 2012, Digital EMC Co., Ltd. 3.2.2 Radiated Emissions - Limit: FCC Part 15.209(a) & RSS-GEN Issue 3, section 7.2.2 and 7.2.5 Frequency [MHz] Field Strength [uV/m] Measurement Distance [Meters] 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 - Procedure: ANCI C63.4 1. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter anechoic chamber test site. The table was rotated 360 degrees to determine the position of the highest radiation. 2. During performing radiated emission below 1 ㎓, the EUT was set 3 meters away from the interference receiving antenna, which was mounted on the top of a variable-height antenna tower. During performing radiated emission above 1 ㎓, the EUT was set 3 meter away from the interference-receiving antenna. 3. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the…

Text truncated - open the document above for the full version.

FCC ID: BEJWCP500 Copyright 2012, Digital EMC Co., Ltd. Client Device Information Note 1: Above client device is not a EUT. The client device is for simu lating various load condition. FCC ID: BEJWCP500 Copyright 2012, Digital EMC Co., Ltd. Description of Test Mode(TM) Test Mode: TM-C FCC ID: BEJWCP500 Copyright 2012, Digital EMC Co., Ltd. Description of Test Mode(TM) Test Mode: TM-L Test Mode: TM-R FCC ID: BEJWCP500 Copyright 2012, Digital EMC Co., Ltd. Description of Test Mode(TM) Test Mode: TM-B Test Mode: TM-T FCC ID: BEJWCP700 Copyright 2012, Digital EMC Co., Ltd. Test Setup Photo(RE) FCC ID: BEJWCP700 Copyright 2012, Digital EMC Co., Ltd. Test Setup Photo(CE) FCC ID: BEJWCP700 Copyright 2012, Digital EMC Co., Ltd. Test Setup Photo for RF Exposure