BEJWCP700Wireless Charging Pad

LG Electronics Wireless Charging Pad WCP-700 User Manual Rev1.0 All rights reserved. LG Electronics inc., 2011 Note: For optimal performance and to prevent any damage to, or misuse of the WCP-700, please read all the information carefully before using the WCP-700. Any modifi cations or changes to this manual due to typographical errors or inaccuracies of stated information shall only be made by LG Electronics Inc.. - Do not drop the Wireless charging pad from high places. - Do not modify, repair, or take the Wireless charging pad apart. - Do not clean with water alcohol or benzene. - Keep the Wireless charging pad away from humidity & dust. - Do not place heavy objects on the Wireless charging pad. Precautions ITEMDescription Input / OutputDC 19V, 500mA / DC 5V, 1000mA Charging time< 4 hours (Based on 1500mAh Battery) Operation temperature-10°C ~ 60°C Dimension / Weight90(W) X 160(L) X 10(H)mm / 125g Included in Package WCP-700 (Wireless Charging Pad) Power SupplyWarranty CardUser Manual Description of parts Power LED Indicator Charging Status LED Indicator DC Jack Audio Charging Indicator Placement Guide FCC NOTICE TO USERS: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. Declaration of confi rmation FCC ID: BEJWCP700 - When disconnecting the power supply, always remove with the plug, do not pull the wire by itself. - Never handle the power plug with wet hands, as this could cause fi re or electric shock. - Refer servicing to qualifi ed personnel only. - Do not open the housing - Do not twist or pinch the power supply cord. If the plugs or power supply cords need to be replaced, ensure that they comply with the manufacturer’s recommendation. - Unplug the device during lighting storms and when unused for extended periods of time. When using an electrical device, especially when children are present, basic safety precautions should always be followed, including the following: DANGER to reduce the risk of electric shock - Always unplug the device from the electrical outlet before cleaning. - Do not reach for a device that has fallen into water. Unplug it immediately. - Do not place or store device where it can fall or be pulled into a tub or sink. - Do not place in or drop into water or other liquid. WARNING to reduce the risk of burns, fi re, electric shock or injury to persons - Do not use with extension cord. - Children should be closely supervised to ensure that they do not play with the device. - Use this device only for its intended use as described in this manual. Do not use with unauthorized accessories of devices. - Never operate this device if it has a damaged cord, plug, cable or housing. If it is not working properly, if it has been dropped or damaged, return it to the LG Service Center for examination and repair. - Keep cord away from heated surfaces. - This device is designed for indoor use only. Do not use outdoors. - Only set on dry surfaces. Do not place on surface wet from water or cleaning solvents. Safety Instructions Function WCP-700 Status Action Power LEDCharging status LED Operating Power supply disconnectedOffOff Power supply connectedSolid RedSolid Orange Charging ChargingSolid RedFlickering Green Charging completeSolid RedSolid Green Error Charging Stopped (Wired phone charger is attached at the same time) Solid Red Solid Red Æ Solid Orange LED display - When the power supply is connected, the wireless charging pad (WCP-700) will turn on. The power Indicator will show a solid red light. - When a Wireless Charging Enabled Device is placed in the correct position, an activation sound will play and the Charging indicator will change from solid orange to fl ickering green. - When charging is completed, the charging indicator will show a solid green light. * RF performance may be affected depending on where the cable is. How to use Charging ox LG Electronics Base de carga inalámbrica WCP-700 Manual del usuario Rev1.0 Todos los derechos reservados. LG Electronics Inc., 2011 Nota: para lograr un rendimiento óptimo y evitar cualquier daño o uso incorrecto de la base de carga inalámbrica WCP-700, lea toda la información cuidadosamente antes de utilizar el producto. Todo cambio o modifi cación que se aplique a este manual debido a errores tipográfi cos o imprecisiones en la información estipulada, será tarea exclusiva de LG Electronics Inc. Contenido del paquete Descripción de las partes Indicador LED de encendido Indicador LED del estado de la carga Toma de CC Indicador de la carga del audio Guía de colocación - No deje caer la base de carga inalámbrica desde lugares altos. - No altere, repare ni desarme la base de carga inalámbrica. - No limpie con agua, alcohol ni bencina. - Mantenga la base de carga inalámbrica lejos de la humedad y del polvo. - No coloque objetos pesados sobre ella. Precauciones ELEMENTODescripción Entrada/salidaCC 19 V, 500 mA/DC 5 V, 1000 mA Tiempo de carga< 4 horas (según la batería de 1500 mAh) Temperatura operativa-10 °C a 60 °C Dimensiones y peso90 (ancho) X 160 (largo) X 10 (alto) mm/125 g AVISO DE LA FCC PARA LOS USUARIOS: Este dispositivo cumple con lo dispuesto en la sección 15 de las reglas de la FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) Este dispositivo no puede causar interferencia nociva. (2) Este dispositivo debe aceptar cualquier interferencia que reciba, incluida la que provoque un funcionamiento no deseado. Aviso de conformidad ID de la FCC: BEJWCP700 Función Estado de la base WCP-700 Acción LED de encendido LED del estado de la carga En funcionamiento Fuente de alimentación desconectada ApagadoApagado Fuente de alimentación conectada Rojo constante Anaranjado constante Carga CargandoRojo constanteVerde parpadeante Carga terminadaRojo constanteVerde constante Error La carga se det…

Text truncated - open the document above for the full version.

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: February 22, 20 11 Com pliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards;

IssueBeforeAfternote Gentlemen: We request FCC certification modifying the circuit of WCP-700 to enhance more the technical specification as below. Date: February 28, 2011 Compliance Certification Services 47173 Benicia Street Fremont, CA 94538 USA Applicant: LG Electronics USA. Manufacturer: LG Electronics Inc. Factory (OEM): WISEPOWER CO., LTD. FCCID: BEJWCP700 Model name: WCP-700 Product name: Wireless Charging Pad FCC EMI Debugging Result (R301) VCC Power Change Switching FET Change Switching Current stablity LED change Blue Led Change issue Noise C22 10uF/6.3V/1608 1 2 C21 0.01uF/25V/1005 1 2 VCC VAA R301 3R/5%/1608 12 FCC Debugging 20110216 C305 10uF/6.3V/1608 1 2 C22 10uF/6.3V/1608 1 2 C21 0.01uF/25V/1005 1 2 VCCVAA Q6 CSD17308Q3 4 5 1 678 23 R56 12R/5%/1608 12 R47 0R/5%/1608 12 Q7 CSD17308Q3 4 5 1 678 23 VINA R56 24R/5%/1608 12 R47 12R/5%/1608 12 Q7 FDNC7692 4 5 1 678 23 VINA Q9 FDNC7692 4 5 1 678 23 Q6 FDNC7692 4 5 1 678 23 R1 1.8K/5%/1005 12 VB D1 BL-HUB35A-AV 12 R1 470R/5%/1005 12 VB D1 NB2012BB 12 Noise Removal Noise Removal (C306) Noise Removal Noise Removal (R303,C304) Noise Removal Noise Removal (C303) Noise Removal Noise Removal (C300) Noise Removal Noise Removal (C302) Noise Removal Noise Removal (C301) Sincerely, Best Regards Soo-Yong, Shim Research engineer Ground Extend Ground extend (S2-2)

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: February 2 2, 2011 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of Digital EMC Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: BEJWCP700 including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of Digital EMC Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from LG Electronics USA. Sincerely, Christopher Johnson Sr. Manager, Standards & Compliance

LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: February 22, 2011 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: BEJWCP700 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description File name PERMANENT 1 Block Diagram Block Diagram_BEJWCP700.pdf 2 Operational Description Operational Description_BEJWCP700.pdf 3 Schematics Schematic_BEJWCP700.pdf 4 Part Lists Part List_BEJWCP700.pdf SHORT-TERM 5 External Photos Ext Photo_BEJWCP700.pdf 6 Internal Photos Int Photo_BEJWCP700.pdf 7 Test-Setup Photos Test Photo_BEJWCP700.pdf 8 Users Manual User Manual_BEJWCP700.pdf The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Christopher Johnson Sr. Manager, Standards & Compliance

FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 1 FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 2 FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 3 FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 4

FCC ID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. Refer to next page. Note 1. The FCC label shown is representative of the label that will appear on the radio when in production. Note 2. The 15.19 statement request is placed in a prominent location in the user`s manual.

FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 1 FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 2 FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 3 FCCID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 4

Report No.: DRTFCC1105-0212 Total 8 Pages DF-403-01(01)100601 Digital EMC Co., Ltd. RF EXPOSURE REPORT Test item : Wireless Charging Pad Model No. : WCP-700 Order No. : 1101-00048 Date of receipt : 2011-01-12 Test date 2011-05-24 Date of issue : 2011-05-24 Use of report : FCC Original Grant Applicant : LG Electronics USA. 1000 Sylvan Avenue Englewood Cliffs, NJ 07632 Test laboratory : Digital EMC Co., Ltd. 683-3, Yubang-Dong, Cheoin-Gu, Yongin-Si, Kyunggi-Do, 449-080, Korea FCC Rule Part : FCC Part 1.1307 (c) and (d) Test environment : See appended test report The test results presented in this test report are limited only to the sample supplied by applicant and the use of this test report is inhibited other than its purpose. This test report shall not be reproduced except in full, without the written approval of DIGITAL EMC CO., LTD. Tested by: Witnessed by: Reviewed by: Engineer S.K. RYU N/A Manager W.J. Lee 1101-00048 DRTFCC1105-0212 TRF-RF-308(01)100709 Page 2 / 8 Copyright ○ C 2011, Digital EMC Co., Ltd. CONTENTS 1. Equipment information ............................................................................... 3 1.1 Equipment description .............................................................................. 3 1.2 Ancillary equipment .................................................................................. 3 2. Information about test items...................................................................... 4 2.1 Operating mode ........................................................................................ 4 2.2 Test Configuration ..................................................................................... 4 2.3 Auxiliary equipment .................................................................................. 5 2.4 Tested environment .................................................................................. 5 3. E and H field strength ................................................................................. 6 1101-00048 DRTFCC1105-0212 TRF-RF-308(01)100709 Page 3 / 8 Copyright ○ C 2011, Digital EMC Co., Ltd. 1. Equipment information 1.1 Equipment description FCC Equipment Class Part 15 Low Power Transmitter Below 1705 kHz (DCD) Equipment type Wireless Charging Pad Equipment model name WCP-700 Equipment add model name N/A Equipment serial no. Identical prototype Frequency range 110 ~ 205 kHz Charging power range 0 ~5 W Device type of WPC protocol Note 1 A1 Device Communication mode Note 2 Analog ping mode, Digital communication mode Power AC-DC Adaptor: AC 120 V 60 Hz Antenna type Internal Loop Antenna (Circular coil) Note 1: This device can charge only one client device at a time with the specific location of the EUT. So this device is a A1 device of the WPC protocol Note 2: Description of communication mode, - Analog ping mode In order to find a client device, the EUT applies a short pulse to its primary coil regularly. The EUT can know the presence of client device on the EUT through monitoring its primary coil current. - Digital communication mode After finding client device, EUT initiates power signal and then receives data PACKETS from the client device according to the WPC protocol. If the client device is removed on the top of the EUT then this communication is stopped at once and the transmitting power signal of the EUT is immediately stopped and the EUT goes to IDLE MODE. The power signal of the EUT shall be used for both communicating data packets from the client device and charging 1.2 Ancillary equipment Equipment Model No. Serial No. Manufacturer Note Adapter WCA-D01WT TA0Z0000034 LG Electronics - - - - - - 1101-00048 DRTFCC1105-0212 TRF-RF-308(01)100709 Page 4 / 8 Copyright ○ C 2011, Digital EMC Co., Ltd. 2. Information about test items 2.1 Operating mode Mode 1 Charging and communication mode Note: Based on the part 15 test results, the emissions of the analog ping mode are very lower than the charging and communication mode. So RF exposure test is performed only with the charging and communication mode. 2.2 Test Configuration This device has been tested with the various resistors to simulate the various load conditions of the client device. The charging current was controlled from 0 mA (Min) to 1000 mA (MAX) by 100 mA step using the resistors and two types of Jig board with rectangular coil. Charging current TM-A-X Series TM-B-X Series 0mA TM-A-X-0 TM-B-X-0 100mA TM-A-X-1 TM-B-X-1 200mA TM-A-X-2 TM-B-X-2 300mA TM-A-X-3 TM-B-X-3 400mA TM-A-X-4 TM-B-X-4 500mA TM-A-X-5 TM-B-X-5 600mA TM-A-X-6 TM-B-X-6 700mA TM-A-X-7 TM-B-X-7 800mA TM-A-X-8 TM-B-X-8 900mA TM-A-X-9 TM-B-X-9 1000mA TM-A-X-10 TM-B-X-10 Note 1: There are 2 types of the test Jigs. The circuit of two Jigs (TM-A and B) is just same. Only different thing is the coil location on the Jig board. TM-A has the coil on the rear side of the PCB. TM-B has the coil on the front side of the PCB. These two versions of test Jigs are for simulating actual client device’s coil locations. Note 2: The Jig board and load resistor shall be placed on the EUT`s chargeable area especially center or near surrounding center. So the Jig board is placed on the center and 4 positions of near surrounding center where can be charged. Above “X” means position of the Jig board on the EUT’s chargeable area as below. C : Center of the Charging area T : Top Side of the Charging area B: Bottom Side of the Charging area R: Right Side of the Charging area L : Left Side of the Charging area Refer to test setup photo for more details. 1101-00048 DRTFCC1105-0212 TRF-RF-308(01)100709 Page 5 / 8 Copyright ○ C 2011, Digital EMC Co., Ltd. 2.3 Auxiliary equipment Equipment Model No. Serial No. Manufacturer Note Jig Board with rectangular coil FULTON N/A LG Electronics Inc. REV09 Note: This Jig board with the rectangular coil was supported by manufacturer for simulating a client device and the load conditions. And they declared that the Jig board will be installed in mobile phones for charging th…

Text truncated - open the document above for the full version.

1101-00048 DRTFCC1103-0150(1) TRF-RF-204(01)110221 Page 2 / 17 Copyright ○ C 2010, Digital EMC Co., Ltd. CONTENTS 1. Equipment information .............................................................. 3 1.1 Equipment description ............................................................. 3 1.2 Ancillary equipment ................................................................. 3 2. Information about test items ..................................................... 4 2.1 Operating mode ....................................................................... 4 2.2 Test mode ................................................................................ 4 2.3 Auxiliary equipment ................................................................. 4 2.4 Tested environment ................................................................. 4 2.5 EMI Suppression Device(s)/Modifications ............................... 4 3. Test Report ................................................................................. 5 3.1 Summary of tests .................................................................... 5 3.2 Transmitter requirements ........................................................ 6 3.2.1 20dB Bandwidth Measurement ........................................... 6 3.2.2 Radiated Emissions ............................................................ 7 3.2.3 AC Line Conducted Emissions ............................................ 9 APPENDIX I................................................................................... 14 1101-00048 DRTFCC1103-0150(1) TRF-RF-204(01)110221 Page 3 / 17 Copyright ○ C 2010, Digital EMC Co., Ltd. 1. Equipment information 1.1 Equipment description FCC Equipment Class Part 15 Low Power Transmitter Below 1705 kHz (DCD) Equipment type Wireless Charging Pad Equipment model name WCP-700 Equipment add model name N/A Equipment serial no. Identical prototype Power AC-DC Adaptor: AC 120V 60Hz Antenna type Internal Loop Antenna(Circular coil) 1.2 Ancillary equipment Equipment Model No. Serial No. Manufacturer Note Adapter WCA-D01WT TA0Z0000034LG Electronics - - - - - - 1101-00048 DRTFCC1103-0150(1) TRF-RF-204(01)110221 Page 4 / 17 Copyright ○ C 2010, Digital EMC Co., Ltd. 2. Information about test items 2.1 Operating mode Operating Mode 1 (OP 1) Charging and communication mode (Charging and DATA packet communication) Operating Mode 2 (OP 2) Analog ping mode (Transmitting a very short pulse to find a client device) 2.2 Test mode This device has been tested below conditions: Charging current TM-A-X Series TM-B-X Series 0mA TM-A-X-0 TM-B-X-0 100mA TM-A-X-1 TM-B-X-1 200mA TM-A-X-2 TM-B-X-2 300mA TM-A-X-3 TM-B-X-3 400mA TM-A-X-4 TM-B-X-4 500mA TM-A-X-5 TM-B-X-5 600mA TM-A-X-6 TM-B-X-6 700mA TM-A-X-7 TM-B-X-7 800mA TM-A-X-8 TM-B-X-8 900mA TM-A-X-9 TM-B-X-9 1000mA TM-A-X-10 TM-B-X-10 Note 1.: “X” = Positions of Jig board on the DUT(Refer to test setup photo.) (C = Center, T = Top, B= Bottom, L = Left, R= Right) 2.3 Auxiliary equipment Equipment Model No. Serial No. Manufacturer Note Jig Board (rectangular coil) FULTON N/A LG Electronics Inc. REV09 Note: This Jig board was supported by manufacturer. And they declared that the Jig board will be installed in mobile phones for charging the phone. 2.4 Tested environment Temperature : 22 ~ 24 o C Relative humidity content : 32 ~ 35 % R.H. Details of power supply :AC 120V 60Hz 2.5 EMI Suppression Device(s)/Modifications EMI suppression device(s) added and/or modifications made during testing → Refer to “Cover Letter(Modification)_BEJWCP700.pdf” file. 1101-00048 DRTFCC1103-0150(1) TRF-RF-204(01)110221 Page 5 / 17 Copyright ○ C 2010, Digital EMC Co., Ltd. 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Test Condition Status Note 1 I. Test Items 2.1049 20 dB Bandwidth Radiated C 15.209 Radiated Emission C 15.207 AC Conducted Emissions AC Line Conducted C Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable The sample was tested according to the following specification: ANSI C-63.4-2003 1101-00048 DRTFCC1103-0150(1) TRF-RF-204(01)110221 Page 6 / 17 Copyright ○ C 2010, Digital EMC Co., Ltd. 3.2 Transmitter requirements 3.2.1 20dB Bandwidth Measurement - Procedure: The 20dB Bandwidth is measured with a spectrum analyzer connected via a receiving antenna placed near the EUT while the EUT is operating. - Measurement Data: ▪ Operating Mode 1 ▪ Operating Mode 2 1101-00048 DRTFCC1103-0150(1) TRF-RF-204(01)110221 Page 7 / 17 Copyright ○ C 2010, Digital EMC Co., Ltd. 3.2.2 Radiated Emissions - Limit: FCC Part 15.209(a): Frequency [MHz] Field Strength [uV/m] Measurement Distance [Meters] 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 - Procedure: ANCI C63.4 1. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter anechoic chamber test site. The table was rotated 360 degrees to determine the position of the highest radiation. 2. During performing radiated emission below 1 ㎓, the EUT was set 3 meters away from the interference receiving antenna, which was mounted on the top of a variable-height antenna tower. During performing radiated emission above 1 ㎓, the EUT was set 3 meter away from the interference-receiving antenna. 3. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10 ㏈ lower than the limit specified, then tes…

Text truncated - open the document above for the full version.

FCC ID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. Jig Board Information Jig Board for TM-A Jig Board for TM-A FCC ID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. Description of test mode Test Mode: TM-A-B Test Mode: TM-B-B Test Mode: TM-A-C Test Mode: TM-B-C Test Mode: TM-A-T Test Mode: TM-B-T FCC ID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. Description of test mode Test Mode: TM-A-L Test Mode: TM-B-L Test Mode: TM-A-R Test Mode: TM-B-R FCC ID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. Test Setup Photo(RE) FCC ID: BEJWCP700 Copyright Ⓒ 2011, Digital EMC Co., Ltd. Test Setup Photo(CE)