BOU-SBT310Wireless Speaker

www.philips.com/welcome Register your product and get support at EN Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Safety Important Safety Instructions a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Do not use this apparatus near water. f Clean only with dry cloth. g Do not block any ventilation openings. Install in accor- dance with the manufacturer’s instructions. h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including i Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If an electrician for replacement of the obsolete outlet. j Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. k manufacturer. l Use only with the cart, stand, tripod, bracket, or table - ratus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. m Unplug this apparatus during lightning storms or when unused for long periods of time. n - vicing is required when the apparatus has been dam- aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. o Battery usage CAUTION – To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: p Apparatus shall not be exposed to dripping or splash- heat. Warning Notice Notice of compliance FCC & RSS compliance statement a This device may not cause harmful interference, and b This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement FCC rules Canada: Disposal of your old product and batteries Information about the use of batteries: Caution Environmental information Note Œªπ∑≠ ̈ªÆ ±≤¥∑≤ª ø ̈ ©©©Ú∞∏∑¥∑∞≠ÚΩ±≥Ò©ª¥Ω±≥ª ̈±ºøß ̈± πª ̈ ̈∏ª ™ªÆß ≥±≠ ̈ ∫Ʊ≥ ß± ́Æ ∞ ́ÆΩ∏ø≠ªÚ ˆ–Ʊ≤ˆflºº∑ ̈∑±≤ø¥ fiª≤ª∫∑ ̈≠ fiß Æªπ∑≠ ̈ªÆ∑≤π ß± ́Æ ∞Ʊº ́Ω ̈Ù ß± ́ ̆¥¥ ƪΩª∑™ÆªΩ ̈¥ß ∫Ʊ≥ ̈∏ª ≥ø≤ ́∫øΩ ̈ ́ƪÆÚ Œªπ∑≠ ̈ªÆ∑≤π ß± ́Æ ∞Ʊº ́Ω ̈ π ́øÆø≤ ̈ªª≠ ̈∏ø ̈ ß± ́ ̆¥¥ ƪΩª∑™ª ø¥¥ ±∫ ̈∏ª ∞Æ∑™∑¥ªπª≠ ̈± ©∏∑Ω∏ ß± ́éƪ ª≤ ̈∑ ̈¥ªºÙ ∑≤Ω¥ ́º∑≤π ≠∞ªΩ∑ø¥ ≥±≤ªßÛ ≠ø™∑≤π ±∫∫ªÆ≠Ú ⁄±Æ › ́≠ ̈±≥ªÆ À≠ª ¤≤ ̈ªÆ 檥±© ̈∏ª ÕªÆ∑ø¥ “±Ú©∏∑Ω∏ ∑≠ ¥±Ωø ̈Û ªº ±≤ ̈∏ª ƪøÆ ±∫ ̈∏ª Ωøæ∑≤ª ̈ÚŒª ̈ø∑≤ ̈∏∑≠ ∑≤∫±Æ≥ø ̈∑±≤ ∫±Æ ∫ ́ ̈ ́ƪ ƪ∫ªÆª≤ΩªÚ ”±ºª¥ “±Ú¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ ÕªÆ∑ø¥ “±Ú¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Ã∏∑≠ çæ±¥ ̈ ±∫ ¥∑π∏ ̈≤∑≤πå ∑≤º∑Ωø ̈ª≠ ́≤∑≤Û ≠ ́¥ø ̈ªº ≥ø ̈ªÆ∑ø¥ ©∑ ̈∏∑≤ ß± ́Æ ́≤∑ ̈ ≥øß Ωø ́≠ª ø≤ ª¥ªΩ ̈Æ∑Ωø¥ ≠∏±ΩμÚ⁄±Æ ̈∏ª ≠ø∫ª ̈ß ±∫ ª™ªÆß±≤ª ∑≤ ß± ́Æ ∏± ́≠ª∏±¥ºÙ∞¥ªø≠ª º± ≤± ̈ ƪ≥±™ª ∞Ʊº ́Ω ̈ Ω±™ªÆ∑≤πÚ Ã∏ª 窮Ω¥ø≥ø ̈∑±≤ ∞±∑≤ ̈å Ωø¥¥≠ ø ̈ ̈ª≤Û ̈∑±≤ ̈± ∫ªø ̈ ́ƪ≠ ∫±Æ ©∏∑Ω∏ ß± ́ ≠∏± ́¥º ƪøº ̈∏ª ª≤Ω¥±≠ªº ¥∑ ̈ªÆø ̈ ́ƪ Ω¥±≠ª¥ß ̈± ∞ÆªÛ ™ª≤ ̈ ±∞ªÆø ̈∑≤π ø≤º ≥ø∑≤ ̈ª≤ø≤Ωª ∞Ʊ楪≥≠Ú ...flŒ“◊“ŸÊñ ƪº ́Ωª ̈∏ª Æ∑≠μ ±∫ ∫∑ƪ ±Æ ª¥ªΩ ̈Æ∑Ω ≠∏±ΩμÙ ̈∏∑≠ ø∞∞øÆø ̈ ́≠ ≠∏± ́¥º ≤± ̈ æª ª®∞±≠ªº ̈± Æø∑≤ ±Æ ≥±∑≠ ̈ ́ƪ ø≤º ±æ∂ªΩ ̈≠ ∫∑¥¥ªº ©∑ ̈∏ ¥∑Ø ́∑º≠Ù≠ ́Ω∏ ø≠ ™ø≠ª≠Ù≠∏± ́¥º ≤± ̈ æª ∞¥øΩªº ±≤ ̈∏∑≠ ø∞∞øÆø ̈ ́≠Ú ›flÀÃ◊—“Êñ ∞ƪ™ª≤ ̈ ª¥ªΩ ̈Æ∑Ω ≠∏±ΩμÙ ≥ø ̈Ω∏ ©∑ºª æ¥øºª ±∫ ∞¥ ́π ̈± ©∑ºª ≠¥± ̈Ù∫ ́¥¥ß ∑≤≠ªÆ ̈Ú flÃä“Ã◊—“Ê–± ́Æ 7™∑ ̈ªÆ ¥ª≠ Ω∏±Ω 7¥ªΩÛ ̈Æ∑Ø ́ª≠Ù∑≤ ̈Ʊº ́∑ƪ ¥ø ¥ø≥ª ¥ø ∞¥ ́≠ ¥øÆπª ºª ¥ø ∫∑Ω∏ª ºø≤≠ ¥ø æ±Æ≤ª Ω±Æƪ≠∞±≤ºø≤ ̈ª ºª ¥ø ∞Æ∑≠ª ª ̈ ∞± ́≠≠ªÆ ∂ ́≠Ø ́éø ́ ∫±≤ºÚ ›±≤πÆø ̈ ́¥ø ̈∑±≤≠ ±≤ ß± ́Æ ∞ ́ÆΩ∏ø≠ªÙ ø≤º ©ª¥Ω±≥ª ̈± ̈∏ª ç∫ø≥∑¥ßˇå ‹ªøÆ –ÿ◊‘◊–Õ ∞Ʊº ́Ω ̈ ±©≤ªÆÊ Ã∏ø≤μ ß± ́ ∫±Æ ß±«± ́陪 ≠ª¥ªΩ ̈ªº ±≤ª ±∫ ̈∏ª æª≠ ̈Ûæ ́∑¥ ̈Ù æª≠ ̈ÛæøΩμªº ∞Ʊº ́Ω ̈≠ ø™ø∑¥ø楪 ̈±ºøßÚ...ªé¥¥ º± ª™ªÆßÛ ̈∏∑≤π ∑≤ ± ́Æ ∞±©ªÆ ̈± 쪪∞ ß± ́ ∏ø∞∞ß ©∑ ̈∏ ß± ́Æ ∞ ́ÆΩ∏ø≠ª ∫±Æ ≥ø≤ß ßªøÆ≠ ̈± Ω±≥ªÚ fl≠ ø ≥ª≥æªÆ ±∫ ̈∏ª –ÿ◊‘◊–Õ ç∫ø≥∑¥ßÙå ß± ́éƪ ª≤ ̈∑ ̈¥ªº ̈± ∞Ʊ ̈ªΩ ̈∑±≤ æß ±≤ª ±∫ ̈∏ª ≥±≠ ̈ Ω±≥∞ƪ∏ª≤≠∑™ª ©øÆÆø≤ ̈∑ª≠ ∑≤ ̈∏ª ∑≤º ́≠ ̈ÆßÚ ...∏ø ̈é≠ ≥±ÆªÙ ß± ́Æ ∞ ́ÆΩ∏ø≠ª π ́øÆø≤ ̈ªª≠ ß± ́饥 ƪΩª∑™ª ø¥¥ ̈∏ª ∑≤∫±Æ≥ø ̈∑±≤ ø≤º ≠∞ªΩ∑ø¥ ±∫∫ªÆ≠ ∫±Æ ©∏∑Ω∏ ß± ́ Ø ́ø¥∑∫ßÙ ∞¥ ́≠ ªø≠ß øΩΩª≠≠ ̈± øΩΩª≠≠±Æ∑ª≠ ∫Ʊ≥ ± ́Æ Ω±≤™ª≤∑ª≤ ̈ ∏±≥ª ≠∏±∞∞∑≤π ≤ª ̈©±ÆμÚ ”±≠ ̈ ∑≥∞±Æ ̈ø≤ ̈¥ßÙ ß± ́ Ωø≤ Ω± ́≤ ̈ ±≤ ± ́Æ ́≤Ω±≥∞Ʊ≥∑≠∑≤π Ω±≥≥∑ ̈Û ≥ª≤ ̈ ̈± ß± ́Æ ̈± ̈ø¥ ≠ø ̈∑≠∫øΩ ̈∑±≤Ú fl¥¥ ±∫ ̈∏∑≠ ∑≠ ± ́Æ ©øß ±∫ ≠øß∑≤𠩪¥Ω±≥ª Û ø≤º ̈∏ø≤μ≠ ∫±Æ ∑≤™ª≠ ̈∑≤π ∑≤ ø –ÿ◊‘◊–Õ ∞Ʊº ́Ω ̈Ú –ÚÕÚ Ã± πª ̈ ̈∏ª ≥±≠ ̈ ∫Ʊ≥ ß± ́Æ –ÿ◊‘◊–Õ ∞ ́ÆΩ∏ø≠ªÙ æª ≠ ́ƪ ̈± ƪπ∑≠ ̈ªÆ ±≤¥∑≤ª ø ̈Ê ©©©Ú∞∏∑¥∑∞≠ÚΩ±≥Ò©ª¥Ω±≥ª Œªπ∑≠ ̈ªÆ∑≤π ß± ́Æ ≥±ºª¥ ©∑ ̈∏ –ÿ◊‘◊–Õ ≥øμª≠ ß± ́ ª¥∑π∑楪 ∫±©Ù≠± º±≤ ̆ ̈ ≥∑≠≠ ± ́ ̈Ú Œªπ∑≠ ̈ªÆ ±≤¥∑≤ª ø ̈ ©©©Ú∞∏∑¥∑∞≠ÚΩ±≥Ò©ª¥Ω±≥ª ̈± ª≤≠ ́ÆªÊ ES Felicidades por la adquisición y bienvenido a Philips Para sacar el mayor partido a la asistencia que proporciona Philips, registre el producto en www.philips.com/welcome . Seguridad Instrucciones de seguridad importantes a Lea estas instrucciones. b Guarde estas instrucciones. c Preste atención a todas las advertencias. d Siga todas las instrucciones. e No use este aparato cerca del agua. f Utilice únicamente un paño seco para la limpieza. g No bloquee las aberturas de ventilación. Realice la ins- talación de acuerdo con las indicaciones del fabricante. h No instale cerca ninguna fuente de calor como, por ejemplo, radiadores, rejillas de calefacción, hornos u otros aparatos que produzcan calor (incluidos los i No omita la opción de seguridad que ofrecen los enchufes polarizados o con conexión a tierra. Un enchufe polarizado tiene dos conectores planos, uno más ancho que el otro. Un enchufe con conexión a tierra tiene dos conectores planos y un tercer conec- tor de conexión a tierra. El conector plano más ancho y el tercer conector le ofrecen seguridad adicional. Si el enchufe suministrado no encaja correctamente en la toma de corrient…

Text truncated - open the document above for the full version.

Zhong Shan City Litai Industrial Co. Ltd No.3 Induxtrial Park, Wuguishan Town, Zhongshan, Guangdong, China 08,Aug, 2012 To whom it may concern CONFIRMATION LETTER We certify that The electrical circuit design, layout, components used and internal wiring for models, except the cabinet color. The test sample is SBT310B/37. For FCC ID SBT310B/37, SBT310W/37, SBT310B/17, SBT310W/17 For IC ID SBT310B/37, SBT310W/37 Signature & stamp

022311 – 6 Authority to Act as Agent Date: _2012-08-01__ American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: __SGS-CSTC Standards Technical Services Co., Ltd.__ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: ___01 November, 2012 ___ By: __________________________ _______Benson Lai_____________ (Signature 1 ) (Print name) Title: __Lead Engineer, Safety, Compliance and Regulatory On behalf of: __ Philips Consumer Lifestyle__ (Company Name) Telephone: ___852-2489-4406 _____________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

022311 – 6 Request for Confidentiality Date: _2011-08-08_ Subject: Confidentiality Request for: ___FCC ID:BOU-SBT310______ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 2 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: _____ _____ ___Philips Consumer Lifestyle__ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 3 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __________________________ _____Benson Lai ______________ (Signature/Title 4 ) (Print name) 2 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 3 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 4 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

External Photos

Internal Photos

SGS-CSTC Standards Technical Services Co., Ltd. Application No..: GZEM1207002833AV Page: 1 of 2 FCC ID: BOU-SBT310 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. RF Exposure Compliance Requirement 1. Standard requirement Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user and the device. (a) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)(mW/cm 2 ) Averaging Times ׀E׀ 2 , ׀H׀ 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)(mW/cm 2 ) Averaging Times ׀E׀ 2 , ׀H׀ 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- F/1500 30 1500-100000 -- -- 1.0 30 Note: f=frequency in MHz; *Plane-wave equivalent power density SGS-CSTC Standards Technical Services Co., Ltd. Application No..: GZEM1207002833AV Page: 2 of 2 FCC ID: BOU-SBT310 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2. MPE Calculation Method E (V/m)=(30*P*G) 0.5 /d Power Density: Pd(W/m 2 )=E 2 /377 E=Electric Field (V/m) P=Peak RF output Power (W) G=EUT Antenna numeric gain (numeric) d= Separation distance between radiator and human body (m) The formula can be changed to Pd= (30*P*G)/(377*d 2 ) From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. 3. Calculated Result and Limit (1)Normal mode: Frequency (MHz) Antenna Gain (Numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 2402 1.00 3.96 2.489 0.0004951 1 Complies 2441 1.00 4.45 2.786 0.0005543 1 Complies 2480 1.00 3.94 2.477 0.0004929 1 Complies (2)EDR mode: Frequency (MHz) Antenna Gain (Numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 2402 1.00 3.19 2.084 0.0004147 1 Complies 2441 1.00 3.75 2.371 0.0004718 1 Complies 2480 1.00 3.31 2.143 0.0004263 1 Complies

SGS-CSTC Standards Technical Services Co., Ltd. 198 Kezhu R oad, Scientech Par k, Guangzhou Economic & Technological Development Distr ict, Guangzhou, China 510663 Telephone: +86 (0) 20 82155555 Fax: +86 (0) 20 82075059 Email: ee.guangzhou@s gs.com Report No.: GZEM120700283301 Page: 1 of 68 FCC ID: BOU-SBT310 Authorized Signature: Strong Yao Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1207002833RF Applicant: Philips Consumer Lifestyle FCC ID: BOU-SBT310 Product Name: Wireless Speaker Product Description: Speaker with BT function to transmit and receive audio signal. Model No.: SBT310B/37, SBT310W/37, SBT310B/17, SBT310W/17 ♣ ♣ ♣♣ ♣ Please refer to section 3 of this report for details Trade Mark: PHILIPS Standards: 47 CFR PART 15 Subpart C: 2011 section 15.247 Date of Receipt: 2012-07-26 Date of Test: 2012-07-26 to 2012-08-07 Date of Issue: 2012-08-16 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further detail. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM120700283301 Page: 2 of 68 FCC ID: BOU-SBT310 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2012-08-16 Original Authorized for issue by: Tested By 2012-07-26 to 2012-08-07 (Daniel He) /Signature Date Prepared By 2012-08-08 (Daniel He) /Signature Date Checked By 2012-08-16 (Strong Yao) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM120700283301 Page: 3 of 68 FCC ID: BOU-SBT310 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Test Summary TEST TEST REQUIREMENT TEST METHOD RESULT Antenna Requirement FCC PART 15 C section 15.247 (c) and Section 15.203 FCC PART 15 C section 15.247 (c) and Section 15.203 PA…

Text truncated - open the document above for the full version.

External Photos Radiated Spurious Emission Test Setup Below 1GHz: Above 1GHz:(full anechoic chamber) Conducted Emission Test Setup