BOUM1BTBluetooth headphone

Always there to help you Register your product and get support at www.philips.com/welcome Question? Contact Philips M1BT User manual Contents 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your wireless on-ear headset 3 What's in the box 3 Other devices Over view of your wireless on-ear headset 3 4 3 Get started 5 Charge your headset 5 Pair the headset with your mobile phone 5 4 Use your headset Connect the headset to a Bluetooth device Manage your calls and music 6 6 6 Wear your headset Use with the audio cable 7 7 5 Technical data 8 6 Notice 9 Declaration of conformity Disposal of your old product and batteries 9 9 Notice for the European Union Trademarks 10 10 7 Frequently asked questions 12 EN 1 1 Important safety instructions Hearing Safety Danger • To avoid hearing damage, limit the time you use the headset at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can’t hear what’s around you. • You should use caution or temporarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headset can cause hearing loss. • Using the headset with both ears covered while driving is not recommended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments. General information To avoid damage or malfunction: Caution • Do not expose the headset to excessive heat. • Do not drop your headset. • Headset shall not be exposed to dripping or splashing. • Do not allow your headset to be submerged in water. • Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. • If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. • The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like. About operating and storage temperatures and operating altitude • Operate or store in a place where temperature is between -15ºC (5ºF) and 55ºC (131ºF) (up to 90% relative humidity. • Batter y life may be shorter in high or low temperature conditions. This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields. 2 EN 2 Your wireless on-ear headset Congratulations on your purchase, and welcome to Philips! To fully benefit from the suppor t that Philips offers, register your product at www.philips.com/welcome. With this Philips wireless on-ear headset, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music; • enjoy music on non-Bluetooth devices with an audio cable. What's in the box Philips Bluetooth wireless on-ear headset M1 BT USB charging cable Audio cable Quick star t guide Other devices A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset (see 'Technical data' on page 8). Note • You can find a list of compatible mobile phones/devices at www.philips.com/support. EN 3 Overview of your wireless on-ear headset f e d c b a a Audio cable jack b Charging slot c Microphone d Volume/Track control button e Call/Music button f LED lights 4 EN 3 Get started Charge your headset Note • Before you use your headset for the first time, charge the batter y for 4 hours for optimum batter y capacity and lifetime. • Use only the original USB charging cable to avoid any damage. • Finish your call before charging the headset, as connecting the headset for charging will power the headset off. • You can operate the headset normally during charging. Connect the supplied USB charging cable to: • the USB connector of the headset and; • USB power source. » LED turns white during charging and turns off when the headset are fully 1 Make sure that the mobile phone is turned on and its Bluetooth feature is activated. 2 Make sure that the headset is fully charged and turned off. 3 Press and hold the call/music button for 10 seconds until the white and blue LED flashes alternately. » The headset remains in pairing mode for 5 minutes. 4 Pair the headset with the mobile phone. For detailed information, refer to the user manual of your mobile phone. The following example shows you how to pair the headset with your mobile phone. 1 Activate the Bluetooth feature of your mobile phone, select Fidelio M1 BT. 2 Enter the headset password "0000" (4 zeros) if prompted. For those mobile phones featuring Bluetooth 2.1+EDR or higher, no need to enter a password. charged. Settings Bluetooth 10:35 Connectivity Settings Devices Found 10:36 10:37 Settings Connectivity Tip • Normally, a full charge takes 5 hours. • When your batter y is empty, you can carr y on listening music with an audio cable. Make sure the headset is off (and not in idle mode) before using this audio cable. Pair the headset with your mobile phone Before you use the headset with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headset and mobile phone. The headset stores the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one. Add Bluetooth device Select Back Fidelio M1BT Select Back Enter Password **** 0000 Select Back EN 5 4 Use your headset Connect the headset to a Manage your calls and music Call/Music button Task Operation Sound or LED indicator Bluetooth device 1 Turn on your mobile phone/Bluetooth device. 2 Press and hold the call/music button to turn the headset on. » The blue LED …

Text truncated - open the document above for the full version.

022311 – 6 Authority to Act as Agent Date: _2013-07-11__ American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: __SGS-CSTC Standards Technical Services Co., Ltd.__ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: ___10 September, 2013 ___ By: __________________________ _______Benson Lai_____________ (Signature 1 ) (Print name) Tit le: __Lead Engineer, Safety, Compliance and Regulatory On behalf of: __ Philips Consumer Lifestyle__ (Company Name) Telephone: ___852-2489-4406_____________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Request for Confidentiality Date: _2013-07-11_____ Subject: Confidentiality Request for: ______FCC ID: BOUM1BT______ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ ______(Insert Company Name)______ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __Safety & Compliance, Lead Engineer________ _Benson Lai____ (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-B ut-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

External Photos

Internal Photos

SGS-CSTC Standards Technical Services Co., Ltd. Application No..: GZEM1305002190RF Page: 1 of 1 FCC ID: BOUM1BT This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. RF Exposure Compliance Requirement The product belongs to standalone portable device base the FCC rule part 2.1091&2.1093. The transmission frequencies of the device are between 100 MHz and 6 GHz. The worst case test separation distance is 5mm. Compare the Maximum Peak output power and e.i.r.p between FHSS and DSSS mode, find the Max Conducted Output Power and SAR Test Exclusion Threshold (mW) are listed below: Transmit frequency (GHz) Max Conducted Output Power (mW) SAR Test Exclusion Threshold (mW) 2.402 3.74 9.7 2.442 5.09 9.6 2.480 5.61 9.5 The SAR Test Exclusion Threshold for 100 MHz to 6 GHz is calculated from: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v05, the SAR report is not required.

SGS-CSTC Standards Technical Services Co., Ltd. 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technological Development District, Guangzhou, China 510663 Telephone: +86 (0) 20 82155555 Fax: +86 (0) 20 82075059 Email: [email protected] Report No.: GZEM130500219002 Page: 1 of 52 FCC ID: BOUM1BT Authorized Signature: Richard Li Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1305002190RF Applicant: Philips Consumer Lifestyle Manufacturer: Philips Electronics Hong Kong Ltd. Factory: Innovation Sound Technology Co., LTD. FCC ID: BOUM1BT Product Name: Bluetooth headphone Product Description: Bluetooth speaker with 2.4 GHz as carrier Model No.: M1BT, M1BT/XX, M1BTYY/XX (XX=00-99, YY=AA-ZZ) ♣ Please refer to section 3 of this report for details Trade mark: Philips Standards: 47 CFR PART 15 Subpart C: 2012 section 15.247 Trade Mark: PHILIPS Date of Receipt: 2013-05-29 Date of Test: 2013-05-29 to 2013-06-20 Date of Issue: 2013-07-01 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further detail. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM130500219002 Page: 2 of 52 FCC ID: BOUM1BT This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2013-07-01 Original Authorized for issue by: Tested By 2013-05-29 to 2013-06-20 (Daniel He) /Signature Date Prepared By 2013-06-21 (Daniel He) /Signature Date Checked By 2013-07-01 (Jeffrey Chen) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM130500219002 Page: 3 of 52 FCC ID: BOUM1BT This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Test Summary TEST TEST REQUIREMENT TEST METHOD RESULT Antenna Requirement FCC PART 15 C section 15.247 (…

Text truncated - open the document above for the full version.

Test Setup Photos Radiated Spurious Emission Test Setup 30 MHz to 1 GHz: Above 1 GHz: Conducted Emission Test Setup