
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Safety and Warranty Before using your set: Check out details inside this booklet EN English This product complies with the radio interference requirements of the European Union. The model and production numbers can be found on the label close to the USB connector. Hearing Safety Listen at a moderate volume: Using headphones at a high volume can impair your hearing. This product can • produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss. Sound can be deceiving. Over time your hearing ‘comfort level’ adapts to • higher volumes of sound. So after prolonged listening, what sounds ‘normal’ can actually be loud and harmful to your hearing. To guard against this, set your volume to a safe level before your hearing adapts and leave it there. To establish a safe volume level: Set your volume control at a low setting.• Slowly increase the sound until you can hear it comfortably and clearly, without • distortion. Listen for reasonable periods of time: Prolonged exposure to sound, even at normally ‘safe’ levels, can also cause • hearing loss. Be sure to use your equipment reasonably and take appropriate breaks.• Be sure to observe the following guidelines when using your headphones. Listen at reasonable volumes for reasonable periods of time.• Be careful not to adjust the volume as your hearing adapts.• Do not turn up the volume so high that you can’t hear what’s around you.• You should use caution or temporarily discontinue use in potentially hazardous • situations. Do not use headphones while operating a motorized vehicle, cycling, • skateboarding, etc.; it may create a traffic hazard and is illegal in many areas. Canada English: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Français: Cet appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur le Brouillage Radioélectrique édicté par le Ministère des Communications du Canada. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : – Relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. The set complies with the FCC-Rules, Part 15. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT Modifications not authorized by the manufacturer may void users authority to operate this device. Philips SA30 SA3 PHILIPS LIMITED WARRANTY ONE (1) YEAR WARRANTY COVERAGE: PHILIPS warranty obligation is limited to the terms set forth below. WHO IS COVERED: Philips warrants the product to the original purchaser or the per- son receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer. The original sales receipt showing the product name and the purchase date from an authorized retailer is considered such proof. WHAT IS COVERED: The Philips warranty covers new products if a defect in material or workmanship occurs and a valid claim is received by Philips within the Warranty Period. At its option, Philips will either (1) repair the product at no charge, using new or refurbished replacement parts, or (2) exchange the product with a product that is new or which has been manufactured from new, or ser- viceable used parts and is at least functionally equivalent or most comparable to the original product in Philips current inventory, or (3) refund the original purchase price of the product. Philips warrants replacement products or parts provided under this warranty against defects in materials and workmanship from the date of the replacement or repair for ninety (90) days or for the remaining portion of the original product’s warranty, whichever provides longer coverage for you. When a product or part is exchanged, any replacement item becomes your property and the replaced item becomes Philips’ property. When a refund is given, your product becomes Philips’ property. Note: Any product sold and identified as refurbished or renewed carries a ninety (90) day limited warranty. Replacement product can only be sent if all warranty requirements are met. Failure to follow all requirements can result in delay. WHAT IS NOT COVERED - EXCLUSIONS AND LIMI- TATIONS: This Limited Warranty applies only to the new products manu- factured by or for Philips that can be identified by the trademark, trade name, or logo affixed to it. This Limited Warranty does not apply to any non-Philips hardware product or any software, even if packaged or sold with the product. Non-Philips manufacturers, suppliers, or publishers may provide a separate warran…
Text truncated - open the document above for the full version.
Statement PHILIPS’s product : GoGear Connect,Wi-Fi MP3 player M/N : SA3CNT32K/37 SA3CNT32K/17 SA3CNT32K/07 SA3CNT32S/37 SA3CNT32S/17 SA3CNT32S/07 SA3CNT08K/37 SA3CNT08K/17 SA3CNT08K/07 SA3CNT08S/37 SA3CNT08S/17 SA3CNT08S/07 SA3CNT16K/37 SA3CNT16K/17 SA3CNT16K/07 SA3CNT16S/37 SA3CNT16S/17 SA3CNT16S/07 These model products will be sold in USA and Canada markets only and do not be sold to other non USA and Canada country markets. The Wi-Fi module of these models does not operate at channel 12, channel13 and channel 14 under 802.11b/g/n modes. Signature and company stamp: Benson LAI Title: Lead Engineer / Safety and Compliance – BG AVM Philips Electronics Hong Kong Ltd.
TO WHOM IT MAY CONCERN DECLARATION OF IDENTITY Model Number: SA3CNT16K/37 Brand Name: PHILIPS Product Name: GoGear Connect, WiFi MP3 Player FCC / IC certificate: Declare the Circuit, PCB Layout, Electrical Parts and Outlook of the following product(s) are identical to all models: New / Additional Model Number(s): GoGear “Connect”, WiFi Mini Tablet with model SA3CNTxxyz/** consist of the various stroke versions which are identical in electrical, mechanical and physical construction. The last two charters ”y” and “z” representative of the following differences. The “y” denoted can be A-W consist of the different cabinet coulour only. The “z” denoted can be A-X or blank consist of the various accessories by-packed and/or packaging used. Stroke number representative of the country of destination are differences /** /07 denoted sales for Cabada only. Ordinary product packaging in D-box type. /17 denote sales for U.S.A only. Ordinary product packaging in D-box type. /37 denote sales for U.S.A and Canada. Ordinary product packaging in D-box type. Memory Size 8GB : SA3CNTxxyz/**, “xx” denoted the flash memory size as 8GB. Memory Size 16GB : SA3CNTxxyz/** “xx” denoted the flash memory size as 16GB. Memory Size 32GB : SA3CNTxxyz/** “xx” denoted the flash memory size as 32GB. Earphone model : Model: AY3840 Name of Factory 1) : Keen High Technologies Ltd. Address : Ze Da Li Industrial Zone, Jian-An 1 Road, New-High Technologies area, Tang Wei, Fuyong, Bao-An, Shenzhen Remarks: All series models do not by-backed any AC/DC adaptor And all models of plastic painting colour (non-conductive painting) Signature with Company Chop : Printed Name : Benson Lai DATE: 2011-08-29
Attestation for FCC Declaration of Conformity FCC ID: BOU Date: 2011-09-14 Please be notified that we, the undersigned, Philips Electronics Hong Kong Ltd. declare that the product bears the above FCC ID is EM-F1000790 also complying with the requirements of FCC DoC. The test report number for FCC DoC is , with is issued by an accredited lab, Audix Technology Corporation, EMC Department located at No. 53-11, Tin-Fu Tsun, Lin-Kou , Taipei Hsien , Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Benson Lai Title of authorized signer: Lead Engineer, Safety and Compliance Company Name: Philips Electronics Hong Kong Ltd. Tel: 852 -2489-4406 Fax: 852 2401-1482 Web site: www.philip.com E-mail: [email protected]
Date: 24 July 2011 Federal Communications Commission Authorization and Evaluation Division FCC ID: BOUSA3CNT08S, BOUSA3CNT16S, BOUSA3CNT32S, BOUSA3CNT08K, BOUSA3CNT16K, BOUSA3CNT32K Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this application as outlined below: 1. Block diagram 2. Schematics 3. Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might to harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Sincerely, Benson Lai Lead Safety Engineer Philips Electronics Hong Kong Ltd. Tel: 852-2489-4406 Fax:852-2401-1482 Web site: www.philips.com E-mail: [email protected]
AGENCY AUTHORIZATION LETTER FCC ID: BOUSA3CNT08S, BOUSA3CNT16S, BOUSA3CNT32S BOUSA3CNT08K, BOUSA3CNT16K, BOUSA3CNT32K Date: 24 July 2011 To whom it may concern: We, the undersigned, hereby authorize Audix Technology (Shenzhen) Co., Ltd Audix of Shenzhen to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by Audix within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months form original date. If you have any Questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, Benson Lai Lead Safety Engineer Philips Electronics Hong Kong Ltd. Tel: 852-2489-4406 Fax:852-2401-1482 Web site: www.philips.com E-mail: [email protected]
R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-1 15. PHOTOS OF THE EUT Figure 1 General Appearance of the EUT Figure 2 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-2 Figure 3 General Appearance of the EUT Figure 4 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-3 Figure 5 General Appearance of the EUT Figure 6 General Appearance of the EUT
R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-4 Figure 7 Inside of the EUT Figure 8 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-5 Figure 9 Inside of the EUT Figure 10 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-6 Figure 11 Inside of the EUT Figure 12 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-7 Figure 13 Inside of the EUT Figure 14 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-8 Figure 15 Inside of the EUT Figure 16 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-9 Figure 17 Inside of the EUT Figure 18 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-10 Figure 19 Inside of the EUT Figure 20 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-11 Figure 21 Inside of the EUT Figure 22 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-12 Figure 23 Inside of the EUT Figure 24 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 15-13 Figure 25 USB Cable Figure 26 Earphone
R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT32K Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11203 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of Philips Electronics Hong Kong Ltd. GoGear Connect, WiFi MP3 Player Test Model: SA3CNT32K/37, SA3CNT32S/37 SA3CNT32K/17, SA3CNT32S/17 FCC ID: BOUSA3CNT32K Prepared for : Philips Electronics Hong Kong Ltd. 5/F.,Philips Electronics Building No.5 Science Park East Avenue, Hong Kong Science Park, Shatin, New Territories, Hong Kong Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Ke Feng Rd., 52 Block, Shenzhen Science & Industrial Park, Nantou, Shenzhen, Guangdong, China Tel: (0755) 26639496 Report Number : ACS-F11203 Date of Test : Aug.03~Sep.16, 2011 Date of Report : Sep.16, 2011 Model Number Brand Name SA3CNTxxyz/** PHILIPS R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT32K Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11203 TABLE OF CONTENTS Description Page 1. SUMMARY OF STANDARDS AND RESULTS.......................................................... 1-1 1.1. Description of Standards and Results .................................................................................. 1-1 2. GENERAL INFORMATION ......................................................................................... 2-1 2.1. Description of Device (EUT) ............................................................................................... 2-1 2.2. Tested Supporting System Details ....................................................................................... 2-3 2.3. EUT Configuration and operation conditions for test.......................................................... 2-3 2.4. Test Facility ......................................................................................................................... 2-4 2.5. Measurement Uncertainty (95% confidence levels, k=2) .................................................... 2-5 3. POWER LINE CONDUCTED EMISSION TEST ....................................................... 3-1 3.1. Test Equipments................................................................................................................... 3-1 3.2. Block Diagram of Test Setup ............................................................................................... 3-1 3.3. Power Line Conducted Emission Test Limits...................................................................... 3-1 3.4. Configuration of EUT on Test ............................................................................................. 3-2 3.5. Operating Condition of EUT................................................................................................ 3-2 3.6. Test Procedure...................................................................................................................... 3-2 3.7. Power Line Conducted Emission Test Results .................................................................... 3-2 4. RADIATED EMISSION TEST ...................................................................................... 4-1 4.1. Test Equipment .................................................................................................................... 4-1 4.2. Block Diagram of Test Setup ............................................................................................... 4-1 4.3. Radiated Emission Limit Standard: FCC 15.209 ................................................................. 4-2 4.4. EUT Configuration on Test.................................................................................................. 4-2 4.5. Operating Condition of EUT................................................................................................ 4-3 4.6. Test Procedure...................................................................................................................... 4-3 4.7. Radiated Emission Test Results ........................................................................................... 4-3 5. CONDUCTED SPURIOUS EMISSIONS...................................................................... 5-1 5.1. Test Equipment .................................................................................................................... 5-1 5.2. Limit..................................................................................................................................... 5-1 5.3. Test Procedure...................................................................................................................... 5-1 5.4. Test result ............................................................................................................................. 5-1 6. CARRIER FREQUENCY SEPARATION TEST ........................................................ 6-1 6.1. Test Equipment .................................................................................................................... 6-1 6.2. Limit..................................................................................................................................... 6-1 6.3. Test Results. ......................................................................................................................... 6-1 7. 20 DB BANDWIDTH TEST ........................................................................................... 7-1 7.1. Test Equipment .................................................................................................................... 7-1 7.2. Limit..................................................................................................................................... 7-1 7.3. Test Results .......................................................................................................................... 7-1 8. NUMBER OF HOPPING FREQUENCY TEST .......................................................... 8-1 8.1. Test Equipment .....................................................................................…
Text truncated - open the document above for the full version.
R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 13-1 13. PHOTOGRAPH OF TEST 13.1.Photos of Power Line Conducted Emission Test R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 14-1 14. PHOTOGRAPH OF TEST 14.1.Photos of Radiated Emission Test (30-1000MHz) R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:BOUSA3CNT08K page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11193 14-2 (Above 1000MHz)
R AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF11006 Page 60 of 75 9. PHOTOGRAPHS OF TEST Bock Right R AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF11006 Page 61 of 75 Left Side Top R AUDIX Technology (Shenzhen) Co., Ltd. Audix Technology (Shenzhen) Co., ltd.. Report No. ACS-SF11006 Page 62 of 75 Front Side
52 Block Shenzhen Science&Industry · Shenzhen · China
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.40 GHz - 2.48 GHz | 1.00 mW |

BLE Activity Monitor with OHR
Equipment Class
DTS - Digital Transmission System
Activity Monitor with OHR
Equipment Class
JBP - Part 15 Class B Computing Device Peripheral
Personal Activity Monitor with Bluetooth Function
Equipment Class
JBP - Part 15 Class B Computing Device Peripheral
1.9GHz DECT Baby Monitor - Baby Unit
Equipment Class
PUB - Part 15 Unlicensed PCS Base Station
1.9GHz DECT Baby Monitor - Parent Unit
Equipment Class
PUT - Part 15 Unlicensed PCS portable Tx worn on body