BOUSHB9100Bluetooth stereo headset

Register your product and get support at www.philips.com/welcome SHB9100 EN User manual 3 English EN Audio quality is poor and crackling noises can be heard. 13 Audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all. 14 I hear but cannot control music on my device (e.g. skip forward/backward). 14 Headset does not work when audio cable is connected. 14 Restore the factory setting 14 Contents 1 Important 4 Hearing Safety 4 Electric-, Magnetic- and Electromagnetic Fields (EMF) 4 General information 4 Disposal of your old product 5 Remove the integrated battery 5 Notice for the European Union 5 Notice for USA (FCC) 5 Trademarks 6 2 Your bluetooth stereo headset 7 Introduction 7 What’s in the box 7 What else you’ll need 7 Compatibility 8 Overview of your Bluetooth stereo headset 8 3 Get started 9 Charge the headset 9 Pair the headset with your mobile phone 9 4 Use the headset 10 Connect the headset to a mobile phone 10 Automatic power saving 10 Use your headset 10 Wear your headset 11 Use with the audio cable 11 5 Technical data 12 6 Frequently asked questions 13 Bluetooth headset does not switch on. 13 No connection to a mobile phone. 13 Pairing does not work. 13 The mobile phone cannot find the headset. 13 Voice dialing or redialing does not work. 13 The other side cannot hear me. 13 The headset is connected to a Bluetooth stereo enabled mobile phone, but music will play on the mobile phone’s speaker only. 13 Contents 4 2. One of Philips’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing products. 3. Philips is committed to develop, produce and market products that cause no adverse health effects. 4. Philips confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today. 5. Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardization for early integration in its products. General information To avoid damage or malfunction: • Do not expose the headset to excessive heat. • Do not drop your headset. • Apparatus shall not be exposed to dripping or splashing. • Do not allow your headset to be submerged in water. • Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. • If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. About operating and storage temperatures • Do not operate or store in a place where temperature is below -15ºC (5ºF) or above 55ºC (131ºF) as this may shorten your battery life. • The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like. 1 Important Hearing Safety Danger To avoid hearing damage, limit the time you use the • headphones at high volume and set the volume to a safe level. The louder the volume, the shorter is the safe listening time. Be sure to observe the following guidelines when using your headphones. Listen at reasonable volumes for • reasonable periods of time. Be careful not to adjust the volume • continuously upwards as your hearing adapts. Do not turn up the volume so high that • you can’t hear what’s around you. You should use caution or temporarily • discontinue use in potentially hazardous situations. Excessive sound pressure from earphones • and headphones can cause hearing loss. Using this headset with both ears covered • while driving is not recommended and may be illegal in some areas while driving. For your safety, avoid distractions from • music or phone calls while in traffic or other potentially dangerous environments. Electric-, Magnetic- and Electromagnetic Fields (EMF) 1. Royal Philips Electronics manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals. EN 5 English Remove the integrated battery Warning Make sure the headset is disconnected from the USB • charging cable before removing the battery. If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headset. Notice for the European Union Hereby, Philips Consumer Lifestyle, BG Accessories, declares that this Philips Bluetooth stereo headset SHB9100 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Notice for USA (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 1234 Disposal of your old product Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health. Battery disposal Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed of with normal household waste. Please inform yourself about the local rules on separ…

Text truncated - open the document above for the full version.

1 Photographs - EUT Constructional Details (Test Model No.: SHB9100)

1 Photographs - EUT Constructional Details (Test Model No.: SHB9100)

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Page: 1 of 1 FCC ID: BOUSHB9100 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1.1 RF Exposure Compliance Requirement 1.1.1 Standard requirement 15.247(b)(4) requirement: (4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section. if transmitting antennas of directional gain greater than 6 dBi are used. the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1). (b)(2). and (b)(3) of this section. as appropriate. by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 1.1.2 EUT RF Exposure The Max Conducted Peak Output Power is 8.28dBm(6.7298mW) in lowest channel; The best case gain of the antenna is 0dBi. 0dB logarithmic terms convert to numeric result is nearly 1. According to the formula. calculate the EIRP test result: EIRP= P x G = 6.7298 mW x 1= 6.7298mW ① SAR requirement: S= 60 / f(GHz) = 60/2.402 = 24.98 mW ② ; ① < ②. So the SAR report is not required.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM110700257201 Page : 1 of 67 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page FCC REPORT Application No: SZEM1107002572RF Applicant: Philips Consumer Lifestyle Manufacturer: Philips Electronics Hong Kong Ltd. Factory: Dong Guan Tai Sing Manufacturing Factory Product Name: Bluetooth stereo headset Operation Frequency: 2402MHz to 2480MHz FCC ID: BOUSHB9100 Standards: FCC CFR Title 47 Part 15 Subpart C Date of Receipt: 2011-07-28 Date of Test: 2011-07-29 to 2011-08-09 Date of Issue: 2011-08-11 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM110700257201 Page : 2 of 67 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents Page 1 COVER PAGE .................................................................................................................................................. 1 2 CONTENTS ....................................................................................................................................................... 2 3 TEST SUMMARY ............................................................................................................................................. 3 4 GENERAL INFORMATION ............................................................................................................................. 4 4.1 CLIENT INFORMATION ................................................................................................................................... 4 4.2 GENERAL DESCRIPTION OF E.U.T................................................................................................................... 4 4.3 E.U.T OPERATION MODE ............................................................................................................................... 6 4.4 DESCRIPTION OF SUPPORT UNITS ................................................................................................................... 6 4.5 TEST FACILITY .............................................................................................................................................. 7 4.6 TEST LOCATION ............................................................................................................................................ 7 4.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER .................................................................................... 7 4.8 TEST INSTR…

Text truncated - open the document above for the full version.

1 Photographs - Test Setup Photo (Test Model No.:SHB9100) Radiated Emission