BRWDASRX102.4 GHz RC Transmitter SR3000

Binding The AR7000 receiver must be bound to the transmitter before it will operate. Binding is the process of teaching the receiver the specific code of the transmitter so it will connect to that specific transmitter. Once bound, the receiver will only connect to the transmitter when the previously bound model memory is selected. If another model memory is selected, the receiver will not connect. This feature is called Model Match ™ and prevents flying a model using the wrong model memory. SmartSafe Fail Safe The AR7000 features the SmartSafe fail-safe system. Smart Safe: • Prevents unintentional electric motor response on start-up. • Eliminates the possibility of over-driving servos on start-up by storing preset fail-safe positions. • Establishes low-throttle fail-safe and maintains last-commanded control surface position if the RF signal is lost. Note: Fail-safe positions are stored via the stick and switch positions on the transmitter during binding. 4. Press and hold the bind button on the back of the transmitter while turning on the power switch. The bind button should flash and within a few seconds the system should connect. The LED’s on the receivers should go solid indicating the system has connected. $3# ").$2!.'%4%34 5. Remove the bind button and store it in a convenient place. REMOVE BEFORE USE 6. After you’ve programmed your model it’s important to rebind the system so the true low throttle and neutral control surface positions are programmed. Note: The AR7000 features DSM ® 2 technology and is only compatible with DSM2 transmitters. The AR7000 will not operate with the DX6 or Spektrum ® surface systems. 1. With the system hooked up as shown, insert the bind plug in the charge plug receptacle. REMOVE BEFORE USE AR7000 2. Turn on the receiver switch. Note that the LED’s on both receivers should be flashing indicating that the receiver is ready to bind. AR7000 LED LED 3. Establish the desired fail-safe stick positions: normally low throttle and flight controls neutral. POWER Inspection or Repairs If this Product needs to be inspected or repaired, please call for a Return Merchandise Authorization (RMA). Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. A Service Repair Request is available at www.horizonhobby.com on the “Support” tab. If you do not have internet access, please include a letter with your complete name, street address, email address and phone number where you can be reached during business days, your RMA number, a list of the included items, method of payment for any non-warranty expenses and a brief summary of the problem. Your original sales receipt must also be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton. Warranty Inspection and Repairs To receive warranty service, you must include your original sales receipt verifying the proof-of- purchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon Hobby. Non-Warranty Repairs Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for repair you are agreeing to payment of the repair without notification. Repair estimates are available upon request. You must include this request with your repair. Non-warranty repair estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Please advise us of your preferred method of payment. Horizon accepts money orders and cashiers checks, as well as Visa, MasterCard, American Express, and Discover cards. If you choose to pay by credit card, please include your credit card number and expiration date. Any repair left unpaid or unclaimed after 90 days will be considered abandoned and will be disposed of accordingly. Please note: non-warranty repair is only available on electronics and model engines. Electronics and engines requiring inspection or repair should be shipped to the following address: Horizon Service Center 4105 Fieldstone Road Champaign, Illinois 61822 All other Products requiring warranty inspection or repair should be shipped to the following address: Horizon Product Support 4105 Fieldstone Road Champaign, Illinois 61822 Please call 877-504-0233 with any questions or concerns regarding this product or warranty. FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range. The associated regulatory agencies of the following countries recognize the noted certifications for this product as authorized for sale and use: Instructions for Disposal of WEEE by Users in the European Union This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equi…

Text truncated - open the document above for the full version.

American TCB 6731 Whittier Ave Suite C110 McLean, Va. 22101 November 14, 2006 Gentlemen: This is your letter of authorization to accept our appointment of Elliott Laboratories, Inc. as Agent for Horizon Hobby Inc., 1657 Country Club Dr., Milpitas CA 95035, to sign applications before the Commission and to make representations to you on our behalf. Elliott Laboratories is to receive and exchange data between our company and the Commission. This authorization is made pursuant to Section 2.911(c) of the FCC Rules and expires on 14 th November 2007. I hereby certify on behalf of Horizon Hobby Inc., 1657 Country Club Dr., Milpitas CA 95035 ("Applicant") that neither Applicant nor any party to the application (officers, directors, and 5% shareholders) is subject to a denial of Federal benefits that includes FCC benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988. 21 U.S.C. 853a. Sincerely, Paul Beard Inventor, Lead Engineer - Spektrum PDF created with pdfFactory trial version www.pdffactory.com

Paul Beard Horizon Hobby Inc. 1657 Country Club Dr., Milpitas CA 95035 USA American TCB 6731 Whittier Ave Suite C110 McLean, Va. 22101 Novemder 14 th 2006 Dear Examiner: I am writing to avoid the possibility of an inadvertent disclosure of proprietary information. The accompanying Form 731 is being filed with the commission on our behalf by Elliott Laboratories, Inc., a consulting and testing laboratory. Included as exhibits with the enclosed application are block diagrams, schematics, and a detailed description of the theory of operation of the device. It is our intention to provide the commission with a full disclosure of our product so that its merits can be evaluated. Indeed, we are pleased to provide any further information that the commission might wish to see. It is not our intention, however, to make our proprietary process a matter of public record. In view of the fact that the block diagrams, schematics, and associated theory of operation disclose the mechanism of our process, we ask that these portions (block diagrams, schematics, and theory of operation) of our application be withheld from public inspection as provided under FCC section 0.459. These documents contain details of the proprietary operation of product. These details are not readily discernible - even to technically sophisticated individuals - from our hardware and constitute trade secrets. In addition, we request temporary non-disclosure for the user manual and all photographs. We request therefore that these documents and this letter be segregated from the body of our evaluation report and withheld from public inspection. Thank you for your attention. Please let the undersigned know if the Commission disagrees with our position or requires further justification. Sincerely, Paul Beard Inventor, Lead Engineer - Spektrum PDF created with pdfFactory trial version www.pdffactory.com

Made in Malaysia FCC ID: BRWDASRX10

FrequencyFCC low threshold FCC low threshold EUT PoutEUT ant. EUT EIRP MHzmWdBmdBmdBidBm 2.40224.9813.98 0.13 22.13 2.47924.2013.84 -0.40 21.60 The maximum EUT EIRP power is 2.13dBm this is below the FCC low threshold calculated to be 13.84dBm. No SAR test is required.

File: R66123 Rev 1 Page 1 of 20 2016-01 Electromagnetic Emissions Test Report and Application for Grant of Equipment Authorization pursuant to FCC Part 15 Subpart C on the Horizon Hobby, Inc. Transmitter Model: AR7000 FCC ID: BRWDASRX10 GRANTEE: Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822 TEST SITE: Elliott Laboratories, Inc. 684 W. Maude Ave Sunnyvale, CA 94086 REPORT DATE: November 15, 2006 FINAL TEST DATE: November 9, 2006 AUTHORIZED SIGNATORY: ______________________________ Juan Martinez Senior EMC Engineer Elliott Laboratories, Inc. is accredited by the A2LA, certificate number 2016-01, to perform the test(s) listed in this report. This report shall not be reproduced, except in its entirety, without the written approval of Elliott Laboratories, Inc. Elliott Laboratories, Inc. -- EMC Department Test Report Report Date: November 15, 2006 File: R66123 Rev 1 Page 2 of 20 pages REVISION HISTORY Revision # Date Comments Modified By 1 November 16, 2006 Initial Release David Guidotti Elliott Laboratories, Inc. -- EMC Department Test Report Report Date: November 15, 2006 File: R66123 Rev 1 Page 3 of 20 pages TABLE OF CONTENTS COVER PAGE............................................................................................................................................................. 1 REVISION HISTORY ................................................................................................................................................ 2 TABLE OF CONTENTS ............................................................................................................................................ 3 SCOPE.......................................................................................................................................................................... 5 OBJECTIVE ................................................................................................................................................................ 6 STATEMENT OF COMPLIANCE ........................................................................................................................... 6 TEST RESULTS SUMMARY.................................................................................................................................... 7 DIGITAL TRANSMISSION SYSTEMS (2400 – 2483.5MHZ) .............................................................................. 7 GENERAL REQUIREMENTS APPLICABLE TO ALL BANDS .......................................................................... 7 MEASUREMENT UNCERTAINTIES ..................................................................................................................... 8 EQUIPMENT UNDER TEST (EUT) DETAILS ...................................................................................................... 9 GENERAL................................................................................................................................................................ 9 ANTENNA SYSTEM .............................................................................................................................................. 9 ENCLOSURE ........................................................................................................................................................... 9 MODIFICATIONS ................................................................................................................................................... 9 SUPPORT EQUIPMENT......................................................................................................................................... 9 EUT INTERFACE PORTS ......................................................................................................................................9 EUT OPERATION ................................................................................................................................................... 9 TEST SITE ................................................................................................................................................................. 10 GENERAL INFORMATION ................................................................................................................................. 10 CONDUCTED EMISSIONS CONSIDERATIONS............................................................................................... 10 RADIATED EMISSIONS CONSIDERATIONS................................................................................................... 10 MEASUREMENT INSTRUMENTATION ............................................................................................................ 11 RECEIVER SYSTEM ............................................................................................................................................ 11 INSTRUMENT CONTROL COMPUTER ............................................................................................................ 11 LINE IMPEDANCE STABILIZATION NETWORK (LISN) ............................................................................... 11 FILTERS/ATTENUATORS................................................................................................................................... 12 ANTENNAS ........................................................................................................................................................... 12 ANTENNA MAST AND EQUIPMENT TURNTABLE ....................................................................................... 12 INSTRUMENT CALIBRATION........................................................................................................................... 12 TEST PROCEDURES............................................................................................................................................... 13 EUT AND CABLE PLACEMENT ...................................................................…

Text truncated - open the document above for the full version.