CQOEN00120SMART KEY ECU

Smart Key ECU Product Outline Product Description Product Type Number %&""#$" RF characteristicNominal frequency433.92MHz Local oscillator frequency52.9025MHz (Crystal) RF AntennaInternal antenna LF characteristicNominal frequency134.2kHz Local oscillator frequency4.2944MHz (Crystal) LF AntennaExternal antenna (Ferrite antenna coil) Transponder characteristic Nominal frequency134.2kHz Local oscillator frequency4.00MHz (Ceramic Resonator) Transponder AntennaExternal antenna (antenna coil) Power SupplyNominal supply voltage12V DC The Smart Key system is a comfort feature that allows the user to lock, unlock the doors of the vehiclewithout using a mechanical key. The user has to carry with him the Smart Key Fob as a wireless authentication is performed when toggle buttonor Start Stop Button inputs are triggered. For communication with the SMARTKey FOB, Smart Key ECUgenerates a request (challenge) as an encoded and modulated signal (134.2 kHz..) at the inductive antenna outputs and receives the SMART KeyFOB's response via the external RF ANT and internal receiver This product is installed inside the vehicle. Appearance Unit : mm 2. Technical description of the system 2.1 Type number -Smart Key ECU: EN00120 2.2 Specifications - Nominal Power supply voltage:12VDC Receiver(RF) -Nominal frequency:433.92MHz -Oscillator frequency:52.9025MHz (Crystal) -Type of modulation:FSK(F1D) -Type of receiving system:Super-heterodyne -Antenna: RF ANT:Internal antenna Transmitter(LF) -Nominal frequency: 134.2kHz -Oscillator frequency:4.2944 MHz (Crystal) -Type of modulation:OOK(A1D) -Antenna:LFANT1:External antenna(inside Cabin) LF ANT2:External antenna(inside Trunk) LF ANT3:External antenna(inside Bumper) LF ANT4:External antenna(Built in Door HDL) LF ANT5:External antenna(Built in Door HDL) Transponder -Nominal frequency: 134.2kHz -Oscillator frequency:4.00MHz (Resonator) -Type of modulation:OOK(A1D) -Antenna: TP ANT:External antenna (Built in SSB) 3. Outline of the system A Smart Key system is a comfort feature that allows the user to lock, unlock without using a mechanical key. Once the user has accessed into the vehicle, with his Smart Key Fob he has the possibility to switch between terminals (OFF-ACC-IGN) and to start the engine. The user has to carry with him the Smart Key Fob as a wireless authentication is performed when toggle button or Start Stop Button inputs are triggered. 3.1. Smart Key ECU The SMK manages all functions related to “SMK Start” The SMK unit reads the inputs (e.g. Start Stop Button), controls the outputs (e.g. exterior and interior antennas), and communicates via the CAN network as well as a single line interface to further devices of the car. For communication with the SMART FOB, SMK generates a request (challenge) as an encoded and modulated signal (134.2 kHz) at the inductive antenna outputs and receives the SMART key FOB's response via the internal RF ANT and internal receiver. The LF antenna amplifier/driver generates a sinusoidal carrier signal (134.2 kHz), which is distributed to the different antennas. The signal is 100%-ASK modulated by switching on and off the carrier. 3.2. LF Antennas: Inductive antennas in and at the vehicle are used to transform the current, driven by the SMK antenna driver, into a magnetic field (134.2 kHz), which is the carrier for the SMK challenge. One antenna covers the vehicle’s interior. One antenna covers the interior of the Trunk. Two antennas in the Door Handles (Left side and Right side) cover the area around the doors. One antenna in the rear bumper covers the area around the trunk for access to the trunk.. Those antennas are based on ferrite core and have a pair of twisted copper cables from antenna to pin header. 3.3. Transponder Antenna: Built in the Start Stop Button to communicate with the transponder by a base station and using wireless communication :(134.2kHz) 3.4. Installation All of antennas and ECU will be installed permanently by professional engineers and end user is not allowed to make any modification. 3.4 Installation in vehicle The Smart Key ECU is installed inside the vehicle. Fig. Outline of the System Smart Key FOB LF ANT Driver Transponder Driver Smart Key ECU RF Receiver TP ANT RF ANT LF ANT Installation in vehicle Smart Key ECU with RF Internal Antenna RF Receiver and LF Driver Door Handle with LF Antenna Start Stop Button with Transponder Antenna LF Antenna Smart Key FOB Fig. Installation of the System FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ■Reorient or relocate the receiving antenna. ■Increase the separation between the equipment and receiver. ■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ■Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Warning "This device complies with Indus…

Text truncated - open the document above for the full version.

DENSO PS ELECTRONICS CORPORATION 853-11, Wae-Dong, Changwon City, Kyungsangnam-do, South, Korea Tel: 82-31-349-9864 / Fax: 82-31-349-5251 http://www.dnpe.co.kr April 5, 2013 Attn: Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize SGS Korea Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits. This authorization is valid until further written notice from us undersigned. Sincerely Yours, Dong-ki Cho Manager DENSO PS Electronics Corporation

DENSO PS ELECTRONICS CORPORATION 853-11, Wae-Dong, Changwon City, Kyungsangnam-do, South, Korea Tel: 82-31-349-9864 / Fax: 82-31-349-5251 http://www.dnpe.co.kr Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 Request of Confidentiality for FCC ID:CQOEN00120 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act,DENSO PS Electronics Corporationhereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for180days after the grant as outlined in Public Notice DA 04-1705. This provision will giveDENSO PS Electronics Corporationtemporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: CONFIDENTIAL LIST Permanent 1Block Diagram 2Operational Descriptions 3Schematics Short-Term 4External Photos 5Internal Photos 6Test-Setup Photos 7User’s Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely Yours, Dong-ki Cho Manager DENSO PS Electronics Corporation

External photos of EUT All view of EUT Test Jig AST EUT DRVSSBBUMTNKINT Front view of EUT Rear view of EUT Top view of EUT Bottom view of EUT Side view of EUT

Internal photos of EUT Internal view of EUT Top view of Main Board Bottom view of Main Board

Report Number:F690501/RF-RTL6381Page:2of20 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGSKoreaCo.,Ltd.(GunpoLaboratory)8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.ee.sgs.com/korea INDEX TABLE OF CONTENTS Page 1. General Information -----------------------------------------------------------------------3 2. Field Strength of Fundamental ----------------------------------------------------------5 3. Spurious Emission--------------------------------------------------------------------------10 4. Occupied Bandwidth-----------------------------------------------------------------------14 Report Number:F690501/RF-RTL6381Page:3of20 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGSKoreaCo.,Ltd.(GunpoLaboratory)8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.ee.sgs.com/korea 1. General Information 1.1. Testing Laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) -Wireless Div. 3FL, 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea 435-040 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible athttp://www.sgs.com/en/Terms-and-Conditions.aspx. Telephone:+82 31 428 5700 FAX:+82 31 427 2371 1.2. Details of Applicant Applicant:DENSO PS Electronics Corp Address:853-11, Oe-Dong, Sungsan-Gu Changwon City, Kyungnam, Korea Contact Person:Cho, Dong-Ki Phone No.:+82 31 340 1938 1.3. Description of EUT Kind of Product Smart Key ECU Model Name EN00120 Serial Number N/A Power Supply DC 12 V (Vehicle battery) Frequency Range Tx: 134.20㎑(LF Antenna) Rx: 433.92㎒(RF Antenna) Modulation Technique ASK Number of Channels 1 Operating Conditions -30°C~ 80°C Antenna Type Internal type (Loop Coil Antenna) 1.4. Declarations by the manufacturer -RF antenna is only Receiver antenna - The EUT of antennas cannot operate at the same time. Report Number:F690501/RF-RTL6381Page:4of20 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGSKoreaCo.,Ltd.(GunpoLaboratory)8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.ee.sgs.com/korea 1.5. Test Equipment List EquipmentManufacturerModelS/NCal. Date Cal. Interval Cal. Due. Spectrum AnalyzerR&SFSV30100768Mar. 28, 2013AnnualMar. 28, 2014 Loop AntennaR&SHFH2-Z2100118Aug. 24, 2011BiennialAug. 24, 2013 Bilog Antenna SCHWARZBECK MESSELEKTRONIK VULB9163396Apr. 27, 2011BiennialApr. 27, 2013 DC Power SupplyAgilentU8002AMY50070064Mar. 28, 2013AnnualMar. 28, 2014 Test ReceiverR&SESU26100109Feb. 28, 2013AnnualFeb. 28, 2014 Antenna MasterINN-COMM4000 N/AN/AN/AN.C.R. Turn TableINN-CODS 1200 S N/AN/AN/AN.C.R. Anechoic ChamberSY Corporation L × W × H (9.6 m × 6.4 m × 6.6 m) N/AN/AN/AN.C.R. 1.6. Test Report Revision RevisionReport numberDescription 0F690501/RF-RTL006381Initial 1.7. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15 Subpart B&C 15.209/ IC RSS-210 Issue8, RSS-Gen Issue3 Section in FCC 15 Subpart B&C§15.209 Section in IC RSS-210 Issue8, RSS-Gen Issue 3 Test ItemResult 15.209(a) RSS-210 Issue8, 2.5.1 RSS-Gen Issue3, 7.2.5 Table 6 Radiated emission, Spurious Emission and Field Strength of Fundamental Complied -RSS-Gen Issue3, 4.6.1Occupied BandwidthComplied Report Number:F690501/RF-RTL6381Page:5of20 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGSKoreaCo.,Ltd.(GunpoLaboratory)8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.ee.sgs.com/korea 2. Field Strength of Fundamental 2.1. Test Setup The diagram below shows the test setup that is utilized to make the measurements for emission from 9㎑to 30㎒Emissions. The diagram below shows the test setup that is utilized to make the measurements for emission from 30㎒to 1㎓Emissions. Report Number:F690501/RF-RTL6381Page:6of20 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGSKoreaCo.,Ltd.(GunpoLaboratory)8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.ee.sgs.com/korea 2.2. Limit 2.2.1. Radiated emission limits, general requirements Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency (㎒) Field Strength (microvolts/meter) Measurement Distance (meter) 0.009 – 0.4902400/F(㎑)300 0.490 – 1.70524000/F(㎑)30 1.705 – 30.03030 30 -88100**3 88 -216150**3 216 - 960200**3 Above 9605003 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72㎒, 76-88㎒, 174-216㎒or 470-806㎒. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241 Report Number:F690501/RF-RTL6381Page:7of20 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGSKoreaCo.,Ltd.(GunpoLaboratory)8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 42…

Text truncated - open the document above for the full version.

Test setup photo of EUT Photo of Test setup