CVTRP7370HRadio Controlled Toy Receiver

- 1 - 1/14 RADIO CONTROL TRUCK Owner's Manual • 2 channel Full Function --- Runs forward, backward, turns left & right and stops. • 3 Band Selector Switch. • Oversized Off-Road tires. • Impact resistant bumper. FEATURES - 3 -- 2 - 1. HOW TO ATTACH ANTENNA TUBE PREPARATION FOR STARTING OPERATION Pass the antenna wire through the antenna tube, then insert the tube into the antenna tube holder. If the antenna tube cannot be successfully inserted into the antenna tube holder, try holding the root of the antenna wire with fingers of one hand and ex - tending the wire with fingers of the other hand. 2. HOW TO INSTALL THE BATTERY To remove the battery lid, press the point marked “OPEN” and pull the lid downward . Transmitter Vehicle When installing a Ni-Cd battery pack, make sure that the power switch of the vehicle is OFF. * Do not charge Battery Pack immediately after use. Wait until it is cooled before charging. * Avoid short circuits. Short circuits will cause overheating, burning of the cords and other damages to the Battery Pack and Charger. * The Ni-Cd Battery Charger should be used for charging one Battery Pack. Do not use the charger for charging other types of batteries and battery packs. * Do not use the Charger as a direct current outlet for other electrical appliances or machines. * Make sure that the Battery Pack and Charger are kept out of the hands of infants and small children while charging. * Do not charge near fires, where the temperature is extremely high, or where it is wet or damp. * The charger will become slightly heated while charging. Allow sufficient free space around the Charger. * If the power of the battery pack is weak in spite of proper charging. The batteries may be worn out from repeated use. Replace it with a new Ni-Cd battery pack. * Dispose of use Ni-Cd battery packs correctly. * Disconnect the supply before making or breaking connections to the battery. * Only use batteries or accumulators of the recommended type or a similar type. * WARNING AGAINST RECHARGING NON-RECHARGEABLE BATTERIES. * Please use this battery charger only for the charge of the rechargeable battery pack. * The Ni-Cd battery pack should be recharged under the supervision of an adult. * This power unit is intended to be correctly orientated in a vertical or floor mount position. Check the batteries regularly for leakage. Remove empty batteries from the toy. Never try to charge non-rechargeable batteries. Rechargeable batteries may only be charge under the supervision of an adult. When inserting the batteries take care not to reverse their polarity. Never use batteries of different manufacturers, and do not mix old and new batteries. Use only the recommended batteries or batteries of equal quality. Never short-circuit the terminals. Removable batteries which can be recharged must be removed from the toy prior to charging. CAUTION : CAUTION : NOT RECOMMENDED FOR CHIL- DREN UNDER 8 YEARS OF AGE. AS WITH ALL ELECTRIC PROD - UCTS, PRECAUTIONS SHOULD BE OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK. INPUT: 120VAC, 60HZ, OUTPUT: 7.25VDC, 180mA ATTENTION PARENTS It is recommended that this toy and all accessories be periodically examined for potential hazards and that any potential hazardous parts be repaired or replaced. CAUTION: ELECTRIC TOY BATTERY REQUIREMENTS Vehicle: Ni-Cd battery energy pack (6.0V, 600-800mAh) Transmitter: 1x9V(006P) battery Repair and Parts Department Monday to Friday 8:30AM-5:30PM Central Time Repair :(800)736-4556 Parts :(800)776-4556 Fax :(972)578-7059 e-mail :[email protected] * Recharge the Battery Before You Start to Operate PRINTED IN CHINA © NIKKO BATTERY CHARACTERISTICS AND RECHARGING TIPSBATTERY CHARACTERISTICS AND RECHARGING TIPS When playing for the first time after purchase, or after a long interval, the battery power may be weak. Even after recharging, the playing time can be relatively short. The battery will gradually regain power after 2 or 3 repetitions of usage and recharging. Install the Ni-Cd battery pack into the battery compartment of the battery charger. Plug the charger into an ordinary household outlet. * The (LED) light on charger should light up when the battery pack is being charged. * Average recharging time is approximately 4 to 5 hours. When the recharging is over, remove the charger from the household outlet. Push the lever of battery charger and disconnect the battery pack from the battery charger. “WARNING! USE UNDER THE DIRECT SUPERVISION OF AN ADULT.” * The newly purchased Ni-Cd pack is not charged. Recharge before operate. 1 Battery charger 2 3 4 1 2 3 4 Battery pack Household outlet Push the level HOW TO RECHARGE * Please read carefully before starting to operate. * Keep the display box and the manual for future reference. * WARNING! Use under the direct supervision of an adult. * Actual product may vary from illustration of this manual. Antenna tube holder Antenna wire Antenna Tube Use a coin to turn the battery stopper to the “OPEN” position. Install the Ni-Cd battery pack into the battery compartment of the vehicle. Replace the battery stopper. 1 2 3 * Note: Be careful not to pull antenna wire too strong. 1 Battery stopper 2 3 Power switch OPEN One 9 volt (006P) battery Install battery making sure that (+) and (-) poles are positioned properly. * Dispose the used battery separately from other trash. CAUTION: * I nstall battery make sure that (+) and (-) poles are positioned properly. Ni-Cd battery energy pack (6.0V) - 4 -- 5 - Adjust the steering alignment when the vehicle does not run straight forward. Turn the steering alignment lever towards “L” if the vehicle runs towards right. Turn the steering alignment lever towards “R” if the vehicle runs towards left. TO ADJUST STEERING ALIGNMENT - 6 - KMNA143520L01(A) (KYP5326-00) THE FCC WANTS YOU KNOW This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This de…

Text truncated - open the document above for the full version.

PCB:NO.RP7370 RECEIVER CIRCUIT EXPLANATION (FCC ID:CVTRP7370H) 1) The Radio Frequency inputted through the Antenna is passed to the Super regenerative receiver formed by TR1,where the action signal is detected. 2) The Action Signal is decode in the IC1,and are send to each output terminal. 3) TR6,7,8,9,10,11 and 12 form the driving motor control circuit. Forward motion. 12P(Pin) of IC1 is turned Hi and TR6,9 and 12 are turned on to make a Forward drive. Backward motion. 11P(Pin) of IC1 is turned Hi and TR7,10 and 11 are turned on to make a backward drive. 4) TR2,3,4 and 5 form the steering control circuit. Right turns. 7P(Pin) of IC1 is turned Hi and TR5 and 2 are turned on to make a Right turn. Left turns. 8P(Pin) of IC1 is turned Hi and TR4 and 3 are turned on to make a Left turn. NIKKO CO.,LTD. R&D Dept. M.MIYAURA

JAPAN QUALITY ASSURANCE ORGANIZATION 21-25, KINUTA 1-CHOME, SETAGAYA-KU, TOKYO 157-8573 JAPAN PHONE (03) 3416-0111, FAX (03) 3416-9691 JQA File No. : 400-70230 Issue Date : July 6, 2007 Page 1 of 25 EMI TEST REPORT JQA File No. : 400-70230 Model No. : RP7370H Type of Equipment : Radio Controlled Toy (Superregenerative Type) Regulations Applied : CFR 47 FCC Rules and Regulations Part 15 FCC ID : CVTRP7370H Applicant : NIKKO CO., LTD. Address : 1-7-14, Mizumoto, Katsushika-ku, Tokyo 125-0032, Japan Manufacturer : NIKKO ELECTRONICS BHD. Address : RLOTT 497 PRAI FREE TRADE ZONE, PRAI INDUSTRIAN ESTATE, 13600 PRAI, PENANG, MALAYSIA Received date of EUT : July 2, 2007 Test Result : Passed Test results in this report are obtained in use of equipment that is traceable to National Institute of Advanced Industrial Science and Technology (AIST) of Japan and National Institute of Information and Communications Technology (NICT) of Japan. The test results only respond to the tested sample. This report should not be reproduced except in full, without the written approval of JQA EMC Engineering Dept. Testing Div. This report must not be used by the client to claim product endorsement by NVLAP or NIST any agency of the U.S. Government. NVLAP Lab Code : 200189-0 JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 2 of 25 TABLE OF CONTENTS Page 1 Documentation 1.1 Test Regulation 3 1.2 General Information 3 1.3 Test Condition 4 – 7 1.4 EUT Modifications / Deviation from Standard 8 1.5 Test results / Uncertainty 9 1.6 Summary 10 1.7 Test Configuration / Operation of EUT 11 1.8 EUT Arrangement (Drawings) 12 1.9 Preliminary Test and Test-setup (Drawings) 13 – 16 1.10 EUT Arrangement (Photographs) 17 - 18 2 Test Data 2.1 AC Power Line Conducted Emission 19(N/A) 2.2 Radiated Emission (Electric Field) 19 – 21 2.3 Antenna Conducted Power 21(N/A) 3 Appendix Test instruments List 22 – 25 JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 3 of 25 1 DOCUMENTATION 1.1 TEST REGULATION FCC Rules and Regulations Part 15 Subpart A and B Superregenerative Receiver Test procedure : AC power line conducted emission, radiated emission and antenna conducted power tests were performed according to the procedures in ANSI C63.4-2003. 1.2 GENERAL INFORMATION 1.2.1 Test facility : 1) Test Facility located at EMC Engineering Dept. Testing Div. : - No. A and B Anechoic Chambers( 3 meters Site ). - Shielded Enclosure. 2) EMC Engineering Dept. Testing Div. is accredited under the National Voluntary Laboratory accreditation Program for satisfactory compliance established in title 15, Part 285 Code of Federal Regulations. NVLAP Lab Code : 200189-0 (Effective through : June 30, 2008) 1.2.2 Description of the Equipment Under Test (EUT) : 1) Type of Equipment : Radio Controlled Toy 2) Product Type : Production 3) Category : Superregenerative Receiver 4) EUT Authorization : Certification 5) FCC ID : CVTRP7370H 6) Trade Name : NIKKO 7) Model No. : RP7370H 8) Tuning Frequency Range : 49.830 MHz – 49.890 MHz 9) Highest Frequency Used in the EUT : - 10) Serial No. : None 11) Date of Manufacture : None 12) Power Rating : 6.0VDC(Ni-Cd Battery) 13) EUT Grounding : None 1.2.3 Definitions for symbols used in this test report : x - indicates that the listed condition, standard or equipment is applicable for this report. - indicates that the listed condition, standard or equipment is not applicable for this report. JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 4 of 25 1.3 TEST CONDITION 1.3.1 The measurement of the AC Power Line Conducted Emission - was performed in the following test site. x - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div. 21-25, Kinuta 1-chome, Setagaya-ku, Tokyo 157-8573, Japan - Shielded Enclosure - Anechoic Chamber No. A (portable Type) Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver N/A Spectrum Analyzer N/A Cable N/A AMN(for EUT) N/A AMN(for Peripheral) N/A Termination N/A JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 5 of 25 1.3.2 The measurement of the Radiated Emission(30 MHz – 1000 MHz) x - was performed in the following test site. - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div. 21-25, Kinuta 1-chome, Setagaya-ku, Tokyo 157-8573, Japan x - Anechoic Chamber No. A (3 meters) - Anechoic Chamber No. B (3 meters) Validation of Site Attenuation : 1) Last Confirmed Date :March, 2007 2) Interval :1 year Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver 11 Antenna 167, 168 Cable 38 RF Amplifier N/A Signal Generator 61 JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 6 of 25 1.3.3 The measurement of the Radiated Emission(Above 1000 MHz) - was performed in the following test site. x - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div. 21-25, Kinuta 1-chome, Setagaya-ku, Tokyo 157-8573, Japan - Anechoic Chamber No. A (3 meters) - Anechoic Chamber No. B (3 meters) Validation of Site Attenuation : 1) Last Confirmed Date :March, 2007 2) Interval :1 year Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver N/A Spectrum Analyzer N/A Cable N/A Antenna N/A RF Amplifier N/A JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 7 of 25 1.3.4 The measurement of the Antenna Conducted Power - was performed in the following test site. x - was not applicable. Test location : Safety & EMC Center EMC Engineering Dept. Testing Div. 21-25, Kinuta 1-chome,…

Text truncated - open the document above for the full version.

JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 17 of 25 1.10 TEST ARRANGEMENT (PHOTOGRAPHS) PHOTOGRAPHS OF EUT CONFIGURATION FOR RADIATED EMISSIONS MEASUREMENT Photograph present configuration with maximum emission JQA File No. :400-70230 FCC ID :CVTRP7370H Model No. :RP7370H Issue Date :July 6, 2007 Standard :CFR 47 FCC Rules Part 15 Page 18 of 25 PHOTOGRAPHS OF EUT CONFIGURATION FOR RADIATED EMISSIONS MEASUREMENT Photograph present configuration with maximum emission