CWTK2101Wireless Bluetooth Photo Printer

Digital Instant Mobile Photo Printer 2 Safety Instructions, FCC, etc. CAUTION RISK OF EXPLODING IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO BATTERY DISPOSAL INSTRUCTIONS. FCC WARNING Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with the FCC/IC radiation exposure limits sent forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET62 and RSS-102 for the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that is should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet, and ankles). This device complies with Part 15 of the FCC Rules and the RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. 3 This product contains electrical or electronic materials. The presence of these materials may, if not disposed of properly, have potential adverse effects on the environment and human health. Presence of this label on the product means it should not be disposed of as unsorted waste and must be collected separately. As a consumer, you are responsible for ensuring that this product is disposed of properly. To fi nd out how to properly dispose of this product, please go to www.polaroid.com and click on “Company“ or call the customer service number for your country listed in the instruction manual. Safety Instructions, FCC, etc. 4 Table of Contents Safety Instructions 2 Product Diagram 4 LED Lights 5 Installing and Charging the Battery 6 Installing the Polaroid® Digital Instant ZINK™ Paper 7 Printing: Digital Camera 8 Printing: Camera Cell Phone 9 Troubleshooting 10 About ZINK™ Technology 11 Specifi cations 12 5 Product Diagram 6 LED Lights 7 Installing and Charging the Battery To install the battery: 1 Remove battery door cover. 2 Install battery. 3 Replace battery door cover. To charge the battery: Install the battery (see above steps). Connect the AC adapter to the printer and the power source. Notes: Before using the printer on battery power, fully charge the battery for 3 hours. The printer is usable while plugged into the power source. 1. 2. • • 8 1 Press and release latch on the paper tray door. 2 Unwrap the 10-pack of Polaroid ® Digital Instant ZINK™ Photo Paper. 3 Slide the 10-pack of Polaroid ® Digital Instant ZINK™ Photo Paper into the printer. Make sure the ZINK Smart Sheet™ is placed facedown. Close the printer tray door. 4 Press the POWER button to turn on the printer. The ZINK Smart Sheet™ will automatically eject. Save the ZINK Smart Sheet™ until the pack of Polaroid ® Digital Instant ZINK™ Photo Paper is completely used. Notes: Only use Polaroid ® Digital Instant ZINK™ Photo Paper. Printer must be empty before refi lling. Do not fi ll printer with more than one 10-pack of Polaroid ® Digital Instant ZINK™ Photo Paper. Avoid bending the Polaroid ® Digital Instant ZINK™ Photo Paper. Avoid fi ngerprints. • • • • Installing Polaroid ® Digital Instant ZINK™ Paper 9 Connect your digital camera and printer to determine if a print option or printer icon is automatically displayed on the camera screen. If no print icon appears, while the digital camera is in “camera” mode, select “menu” and navigate and confi rm that PictBridge is enabled under “settings” or while in “view” mode, select “menu” and navigate to confi rm PictBridge is enabled. Note: if “USB” is displayed under “settings” then PictBridge is NOT enabled. Once PictBridge is enabled, select the image you want to print and follow the on-screen PictBridge instructions to print. For specifi c print directions for your digital camera, please visit the digital camera user’s manual or manufacturer’s website for PictBridge printing instructions. Notes: Do not open paper tray door while printing. Do not turn off printer while printing. Do not disconnect the USB cord until entire printing process is complete. 1. 2. 3. • • • Printing: Digital Camera 10 Passcode: 6000 Select the image to print from the stored images on your camera cell phone. In the “options” menu, select “send via Bluetooth.” Select the Polaroid printer and print. If you are unable to print from “send via Bluetooth,” select “connectivity” or “Bluetooth” under the “settings” or “tools” menu. Select the Polaroid printer. Once paired, go back to stored images and select the image you want to p…

Text truncated - open the document above for the full version.

External Photo ALPS ELECTRIC CO.,LTD Photo Printer FCC ID: CWTK2101 Model: CZA-10011B IC Number: 1778F-K2101 Front Rear External Photo ALPS ELECTRIC CO.,LTD Photo Printer FCC ID: CWTK2101 Model: CZA-10011B IC Number: 1778F-K2101 Top Bottom External Photo ALPS ELECTRIC CO.,LTD Photo Printer FCC ID: CWTK2101 Model: CZA-10011B IC Number: 1778F-K2101 Right Left

Antenna andBT Module mountingboard Upset toAntenna and BT module location side BT module Antenna Antenna and BT modulelocation erea.But These are locatedon the reverse side onboard. Macro side angle Antenna Internal Photo ALPS ELECTRIC CO.,LTD Photo Printer FCC ID: CWTK2101 Model: CZA-10011B IC Number: 1778F-K2101 BT Module with shield Top of BT Module Internal Photo ALPS ELECTRIC CO.,LTD Photo Printer FCC ID: CWTK2101 Model: CZA-10011B IC Number: 1778F-K2101 Bottom of BT Module

UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 Applicant: ALPS Electric co., Ltd Peripheral products division Onahama Pla Type of Equipment : Photo Printer M odel No. : CZA-10011B FCC ID: CW TK 2101 ALPS Electric co., Ltd Peripheral products division Onahama Plant declares that Model : Photo Printer complies with FCC radiation exposure requirement specified in the FCC Rules 2.1093. The “CZA-10011B“ has 1.44 mW of conducted Peak Output power and 1.81 mW of EIRP. This equipment is considered as a mobile device so that SAR testing is excluded. The Following calculation is the reference data for 20cm distance. RF Exposure Calculations: The following information provides the minimum separation distance for the highest gain antenna provided with the “CZA-10011B“ as calculated from FCC OET Bulletin 65 Appendix A, Table (B) Limits for General Population / Uncontrolled Exposure. This calculation is based on the highest EIRP possible from the system, considering maximum power and antenna gain, and considering a 1.0mW/cm^2 uncontrolled exp o su re lim it. T he F riis fo rm u la u sed w as: S = (P * G) / (4* π * r 2 ) Where P = 1.44 mW (M aximum peak output power) G = 1.26 Numerical Antenna gain; equal 1.00 dBi r =20.0 cm For: CZA-10011BS = 0.00036 mW/cm 2 No. : 28EE0156-YK-01-B RF Exposure / SAR Statement

FCC ID : CWTK2101 Test report No. : 28EE0156-YK-01-B Page : 2 of 88 Issued date : February 19, 2008 UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 MF060b (09.01.08) Table of Contents Page 1 Applicant Information 3 2 Equipment under test (E.U.T.) 3 3 Test Specification, Procedures and Results 4 4 System Test Configuration 6 5 Conducted emission 7 6 Carrier Frequency Separation 7 7 20dB Bandwidth & Occupied Bandwidth (99%) 7 8 Number of Hopping Frequency 8 9 Dwell time 8 10 Maximum Peak Output Power 8 11 Out of Band Emissions (Antenna Port Conducted) 8 12 Out of Band Emissions (Radiated) 9 Contents of Appendixes 10 APPENDIX 1: Photographs of test setup 11 APPENDIX 2: Test Data 14 APPENDIX 3: Test instruments 88 FCC ID : CWTK2101 Test report No. : 28EE0156-YK-01-B Page : 3 of 88 Issued date : February 19, 2008 UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 MF060b (09.01.08) 1 Applicant Information Company Name : ALPS Electric Co., Ltd Peripheral products division Onahama Plant Address : 41-25 Yanagi-machi, Noda Onahama, Iwaki-shi, Fukushima 971-8615 JAPAN Telephone Number : +81-246-76-0151 Facsimile Number : +81-246-58-7994 Contact Person : Junichi Kurechi 2 Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Photo Printer Model No. : CZA-10011B Serial No. : Refer to 4.2 in this report. Rating : AC100-240V, 50/60Hz Country of Manufacture : Japan Receipt Date of Sample : January 8, 2007 Condition of EUT : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No modification by the test lab. 2.2 Product Description ALPS Electric co., Ltd Peripheral products division Onahama Plant, Model: CZA-10011B (referred to as the EUT in this report) is a Photo Printer. The clock frequency used in EUT: CPU: 12MHz Radio Specification Equipment type : Transceiver Frequency of operation : 2402-2480MHz Other clock frequency Bandwidth & channel spacing Type of modulation : : : 26MHz 79MHz & 1MHz FHSS (GFSK, S/4DQPSK, 8DPSK) Antenna model & type Antenna gain : : AF 216M245001-T (Helical antenna) +1.0dBi (Max.) Antenna connector type : None ITU code : F1D, G1D Operation temperature range : -20 ~ +75 deg. C. FCC Part15.31 (e) The Bluetooth module is provided with stable power supply (DC3.3 V), therefore, the equipment complies power supply regulation. FCC Part15.203 Antenna requirement It is impossible for end users to replace the antenna, because the antenna is mounted inside of the module. Therefore, the equipment complies with the antenna requirement of Section 15.203. FCC ID : CWTK2101 Test report No. : 28EE0156-YK-01-B Page : 4 of 88 Issued date : February 19, 2008 UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 MF060b (09.01.08) 3 Test Specification, Procedures and Results 3.1 Test specification Test specification : FCC Part15 Subpart C: 2008, final revised on January 30, 2008 Title : FCC 47CFR Part15 Radio Frequency Device Subpart C Intentional Radiators Section 15.207 Conducted limits Section 15.209 Radiated emission limits, general requirements Section 15.247 Operation within the bands 902-928MHz, 2400-2483.5MHz, and 5725-5850MHz *The revision on January 30, 2008 does not influence the test specification applied to the EUT. 3.2 Procedures & Results ItemTest Procedure SpecificationRemarksDeviationWorst Margin Results Conducted emission ANSI C63.4:2003 7. AC powerline conducted emission measurements FCC 15.207 -N/A 17.6dB (0.1980MHz, QP, N, Tx 2402MHz, 3DH5) Complied Carrier Frequency Separation FCC Public Notice DA 00-705 FCC15.247 (a)(1) ConductedN/A Complied 20dB Bandwidth FCC Public Notice DA 00-705 FCC15.247 (a)(1) ConductedN/A Complied Number of Hopping Frequency FCC Public Notice DA 00-705 FCC15.247 (a)(1)(iii) ConductedN/A Complied Dwell time FCC Public Notice DA 00-705 FCC15.247 (a)(1)(iii) ConductedN/A Complied Maximum Peak Output Power FCC Public Notice DA 00-705 FCC15.247 (b)(1) ConductedN/A *See data. Complied Spurious Emission FCC Public Notice DA 00-705 FCC15.209 FCC15.247 (d) Conducted/ Radiated N/A 0.8dB (1654.00MHz, AV, Horizontal, Tx 2480MHz 3DH5) Complied Note: UL Japan’s EMI Work Procedures No.QPM05 and QPM15. In case any questions arise about test procedure, ANSI C63.4: 2003 is also referred. 3.3 Addition to standard ItemTest Procedure SpecificationRemarksWorst Margin Results Occupied Bandwidth (99%) ANSI C63.4:2003 13. Measurement of intentional radiators RSS-Gen 4.6.1 RSS-Gen 4.6.1 Conducted- Complied * Other than above, no addition, exclusion nor deviation has been made from the standard. FCC ID : CWTK2101 Test report No. : 28EE0156-YK-01-B Page : 5 of 88 Issued date : February 19, 2008 UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 MF060b (09.01.08) 3.4 Uncertainty The following uncertainties have been calculated to provide a confidence level of 95% using a coverage factor k=2. No.1 open site (r) No.2 open site (r) No.1 anechoic chamber (r) Conducted emission 150kHz-30MHz 2.8 dB 2.8 dB 2.8 dB Radiated emission (3m) 30-300MHz 4.5 dB 4.4 dB 4.5 dB 300-1000MHz 4.3 dB 4.3 dB 4.3 dB 1GHz< 5.7 dB 5.7 dB 5.7 dB Antenna port conducted test ( r ) Below 1GHz 0.4dB 1GHz and above 0.7dB Conducted Emission Test The data listed in this test report has enough margin, more than site margin. Radiated Emission Test The data listed in this report meets the limits unless the uncertainty is taken into consideration. 3.5 Test Location UL Japan, Inc. Yamakita EMC Lab. 907, Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken 258-0124 JAPAN Telephone number…

Text truncated - open the document above for the full version.

DATA OF CONDUCTION TEST UL Japan, Inc. YAMAKITA No.1 SHIELD ROOM 4GRQTV0Q'';-$ #RRNKECPV#.25'.'%64+%%1.6& -KPFQH'SWKROGPV2JQVQ2TKPVGT /QFGN0Q%<#$ 5GTKCN0Q 2QYGT#%8*\ /QFG6TCPUOKVVKPI/*\ &* 4GOCTMU &CVG 2JCUG5KPING2JCUG 6GORGTCVWTG͠'PIKPGGT ;CUWOCUC1YCMK *WOKFKV[㧑 4GIWNCVKQP(%%2CTV$%.#55$ %+5242WD 0Q(4'34'#&+0) 0 4'#&+0) . .+50%#$.'#66'04'57.6.+/+65/#4)+0 32#832#8(#%614.15532#832#832#8 =/*\?=F$Ǵ8?=F$Ǵ8?=F$?=F$?=F$?=F$?=F$Ǵ8?=F$Ǵ8?=F$?                                                                     %#.%7.#6+104'#&+0) .+50(#%614 %#$.'.155 #66'0 50+.ع5.- -.05 .#+:#1%ع'.$#%%%- '27.5ع4'66/+..2- .2 +/'ع4'8+'%'464- 5%5'  2CIG 14 DATA OF CONDUCTION TEST UL Japan, Inc. YAMAKITA No.1 SHIELD ROOM 4GRQTV0Q'';-$ #RRNKECPV#.25'.'%64+%%1.6& -KPFQH'SWKROGPV2JQVQ2TKPVGT /QFGN0Q%<#$ 5GTKCN0Q 2QYGT#%8*\ /QFG6TCPUOKVVKPI/*\ &* 4GOCTMU &CVG 2JCUG5KPING2JCUG 6GORGTCVWTG͠'PIKPGGT ;CUWOCUC1YCMK *WOKFKV[㧑 4GIWNCVKQP(%%2CTV$%.#55$ %+5242WD =F$Ǵ8? (TGSWGPE[=/*\? 3غWCUK2GCM˜#XGTCIG          2CIG 15 DATA OF CONDUCTION TEST CHART UL Japan, Inc. YAMAKITA No.1 SHIELD ROOM 4GRQTV0Q'';-$ #RRNKECPV#.25'.'%64+%%1.6& -KPFQH'SWKROGPV 2JQVQ2TKPVGT /QFGN0Q%<#$ 5GTKCN0Q 2QYGT#%8*\ /QFG6TCPUOKVVKPI/*\ &* 4GOCTMU &CVG 2JCUG5KPING2JCUG 6GORGTCVWTG͠'PIKPGGT ;CUWOCUC1YCMK *WOKFKV[㧑 4GIWNCVKQP(%%2CTV$%.#55$ %+5242WD 4GIWNCVKQP0QPG 'OKUUKQP.GXGN=F$Ǵ8?2*#5'0 (TGSWGPE[=/*\?          'OKUUKQP.GXGN=F$Ǵ8?2*#5'. (TGSWGPE[=/*\?          2CIG 16 DATA OF CONDUCTION TEST CHART UL Japan, Inc. YAMAKITA No.1 SHIELD ROOM 4GRQTV0Q'';-$ #RRNKECPV#.25'.'%64+%%1.6& -KPFQH'SWKROGPV 2JQVQ2TKPVGT /QFGN0Q%<#$ 5GTKCN0Q 2QYGT#%8*\ /QFG6TCPUOKVVKPI/*\ &* 4GOCTMU &CVG 2JCUG5KPING2JCUG 6GORGTCVWTG͠'PIKPGGT ;CUWOCUC1YCMK *WOKFKV[㧑 4GIWNCVKQP(%%2CTV$%.#55$ %+5242WD 4GIWNCVKQP0QPG 'OKUUKQP.GXGN=F$Ǵ8?2*#5'0 (TGSWGPE[=/*\?          'OKUUKQP.GXGN=F$Ǵ8?2*#5'. (TGSWGPE[=/*\?          2CIG 17 DATA OF CONDUCTION TEST CHART UL Japan, Inc. YAMAKITA No.1 SHIELD ROOM 4GRQTV0Q'';-$ #RRNKECPV#.25'.'%64+%%1.6& -KPFQH'SWKROGPV 2JQVQ2TKPVGT /QFGN0Q%<#$ 5GTKCN0Q 2QYGT#%8*\ /QFG6TCPUOKVVKPI/*\ &* 4GOCTMU &CVG 2JCUG5KPING2JCUG 6GORGTCVWTG͠'PIKPGGT ;CUWOCUC1YCMK *WOKFKV[㧑 4GIWNCVKQP(%%2CTV$%.#55$ %+5242WD 4GIWNCVKQP0QPG 'OKUUKQP.GXGN=F$Ǵ8?2*#5'0 (TGSWGPE[=/*\?          'OKUUKQP.GXGN=F$Ǵ8?2*#5'. (TGSWGPE[=/*\?          2CIG 18 DATA OF CONDUCTION TEST UL Japan, Inc. YAMAKITA No.1 SHIELD ROOM 4GRQTV0Q'';-$ #RRNKECPV#.25'.'%64+%%1.6& -KPFQH'SWKROGPV2JQVQ2TKPVGT /QFGN0Q%<#$ 5GTKCN0Q 2QYGT#%8*\ /QFG6TCPUOKVVKPI/*\ &* 4GOCTMU &CVG 2JCUG5KPING2JCUG 6GORGTCVWTG͠'PIKPGGT ;CUWOCUC1YCMK *WOKFKV[㧑 4GIWNCVKQP(%%2CTV$%.#55$ %+5242WD 0Q(4'34'#&+0) 0 4'#&+0) . .+50%#$.'#66'04'57.6.+/+65/#4)+0 32#832#8(#%614.15532#832#832#8 =/*\?=F$Ǵ8?=F$Ǵ8?=F$?=F$?=F$?=F$?=F$Ǵ8?=F$Ǵ8?=F$?                                                                     %#.%7.#6+104'#&+0) .+50(#%614 %#$.'.155 #66'0 50+.ع5.- -.05 .#+:#1%ع'.$#%%%- '27.5ع4'66/+..2- .2 +/'ع4'8+'%'464- 5%5'  2CIG 19 DATA OF CONDUCTION TEST UL Japan, Inc. YAMAKITA No.1 SHIELD ROOM 4GRQTV0Q'';-$ #RRNKECPV#.25'.'%64+%%1.6& -KPFQH'SWKROGPV2JQVQ2TKPVGT /QFGN0Q%<#$ 5GTKCN0Q 2QYGT#%8*\ /QFG6TCPUOKVVKPI/*\ &* 4GOCTMU &CVG 2JCUG5KPING2JCUG 6GORGTCVWTG͠'PIKPGGT ;CUWOCUC1YCMK *WOKFKV[㧑 4GIWNCVKQP(%%2CTV$%.#55$ %+5242WD =F$Ǵ8? (TGSWGPE[=/*\? 3غWCUK2GCM˜#XGTCIG          2CIG 20…

Text truncated - open the document above for the full version.

FCC ID : CWTK2101 Test report No. : 28EE0156-YK-01-B Page : 11 of 88 Issued date : February 19, 2008 UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 MF060b (09.01.08) Conducted emission FCC ID : CWTK2101 Test report No. : 28EE0156-YK-01-B Page : 12 of 88 Issued date : February 19, 2008 UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 MF060b (09.01.08) Radiated emission FCC ID : CWTK2101 Test report No. : 28EE0156-YK-01-B Page : 13 of 88 Issued date : February 19, 2008 UL Japan, Inc. YAMAKITA EMC LAB. 907 Kawanishi, Yamakita-machi, Ashigarakami-gun, Kanagawa-ken, 258-0124 JAPAN Telephone: +81 465 77 1011 Facsimile: +81 465 77 2112 MF060b (09.01.08) Pre-check of the worst position X-axis Y-axis Z-axis