DI2CT-8TD726AProgrammable Thermostat with EM260 Zigbee

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of FCC RF Rules. Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

Neutron Engineering Inc. Project No.: 0905C047B Page 2 of 7 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 2 of 7 0905C047B 0905C047B

Neutron Engineering Inc. Project No.: 0905C047B Page 3 of 7 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 3 of 7 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 4 of 7 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 4 of 7 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 5 of 7 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 5 of 7 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 6 of 7 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 7 of 7 0905C047 0905C047B 0905C047B Neutron Engineering Inc. Project No.: 0905C047B Page 7 of 7 0905C047 0905C047B 0905C047B

Neutron Engineering Inc. Ii CC Ra io Test Report C 10: 012CT-8T0726A This report concerns (check one) : Original Grant lass I Change Issued Date : May. 18,2010 Project No. : 0905C047B Equipment : Programmable Thermostat with EM260 Zigbee Model Name : 8TD726A Applicant : Computime Limited Address : 17/F, Great Eagle Centre, 23 Harbour Road, Wanchai, Hong Kong Manufacturer: Computime Electronics(shenzhen)company Limited. Address : computime Technology Park,Dan Zhu Tou Cun,Buji,Longgang Region,Shenzhen Tested by: Neutron Engineering Inc. EMC Laboratory Date of Test: May. 18, 2009 - Aug. 04, 2009 Testing Engineer JJJ-'1~_ Technical Manager - J/\L (Vic Chiu) Authorized Signatory S~L (Steven Lu) NEUTRON ENGINEERING INC. No. 132-1, Lane 329, Sec. 2, Palain Rd., Shijr City, Taipei, Taiwan TEL : (02) 2646-5426 FAX: (02) 2646-6815 ...,~\\H]f·/'" ~'~/'~' Ia~;'~ @5 ~..... ~~--'" ~!2~~~ W' I,/.~~ ~ ~~1. r"'\ ~....... 'I (1/,,111\\'\'\ n.ibtl.l~lNnl"'" .0659 Report No.." NEI-FCCP-1-0905C047B Page 1 of 55 Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 2 of 55 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutron shall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 3 of 55 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 10 3.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 3.5 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 4.1.2 MEASUREMENT INSTRUMENTS LIST AND SETTING 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 14 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 17 4.2.1 RADIATED EMISSION LIMITS 17 4.2.2 MEASUREMENT INSTRUMENTS LIST ANS SETTING 18 4.2.3 TEST PROCEDURE 19 4.2.4 DEVIATION FROM TEST STANDARD 19 4.2.5 TEST SETUP 20 4.2.6 EUT OPERATING CONDITIONS 20 4.2.7 TEST RESULTS (BETWEEN30 – 1000 MHZ) 21 4.2.8 TEST RESULTS (ABOVE 1000 MHZ) 23 4.2.9 TEST RESULTS (RESTRICTED BANDS REQUIREMENTS) 35 5 . BANDWIDTH TEST 39 5.1 APPLIED PROCEDURES / LIMIT 39 5.1.1 MEASUREMENT INSTRUMENTS LIST 39 5.1.2 TEST PROCEDURE 39 5.1.3 DEVIATION FROM STANDARD 39 5.1.4 TEST SETUP 39 5.1.5 EUT OPERATION CONDITIONS 39 Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 4 of 55 Table of Contents Page 5.1.6 TEST RESULTS 40 6 . PEAK OUTPUT POWER TEST 42 6.1 APPLIED PROCEDURES / LIMIT 42 6.1.1 MEASUREMENT INSTRUMENTS LIST 42 6.1.2 TEST PROCEDURE 42 6.1.3 DEVIATION FROM STANDARD 42 6.1.4 TEST SETUP 42 6.1.5 EUT OPERATION CONDITIONS 42 6.1.6 TEST RESULTS 43 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 44 7.1 APPLIED PROCEDURES / LIMIT 44 7.1.1 MEASUREMENT INSTRUMENTS LIST 44 7.1.2 TEST PROCEDURE 44 7.1.3 DEVIATION FROM STANDARD 44 7.1.4 TEST SETUP 44 7.1.5 EUT OPERATION CONDITIONS 45 7.1.6 TEST RESULTS 46 8 . POWER SPECTRAL DENSITY TEST 48 8.1 APPLIED PROCEDURES / LIMIT 48 8.1.1 MEASUREMENT INSTRUMENTS LIST 48 8.1.2 TEST PROCEDURE 48 8.1.3 DEVIATION FROM STANDARD 48 8.1.4 TEST SETUP 48 8.1.5 EUT OPERATION CONDITIONS 48 8.1.6 TEST RESULTS 49 9 . RF EXPOSURE TEST 51 9.1 APPLIED PROCEDURES / LIMIT 51 9.1.1 MEASUREMENT INSTRUMENTS LIST 51 9.1.2 MPE CALCULATION METHOD 52 9.1.3 DEVIATION FROM STANDARD 52 9.1.4 TEST SETUP 52 9.1.5 EUT OPERATION CONDITIONS 52 9.1.6 TEST RESULTS 53 10 . EUT TEST PHOTO 54 Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 5 of 55 1. CERTIFICATION E q u i p m e n t : Programmable Thermostat with EM260 Zigbee Trade Name : N/A Model Name : 8TD726A A p p l i c a n t : Computime Limited Factory : Computime Electronics(shenzhen)company Limited. A d d r e s s : computime Technology Park,Dan Zhu Tou Cun,Buji,Longgang Region,Shenzhen T e s t I t e m : ENGINEERING SAMPLE Date of Test: : May. 18, 2009 ~ Aug. 04, 2009 Standards : FCC Part15, Subpart C(15.247) / ANSI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-0905C047B) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Test result included in this re…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 54 of 55 10. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 54 of 55 10. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 55 of 55 Radiated Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-0905C047B Page 55 of 55 Radiated Measurement Photos