DXXVT0190-00000Panorama Wireless Transceiver

Copyright © Datascope Corp., 2004. Printed in U.S.A. All rights reserved. Contents of this publication may not be reproduced in any form without permission of Datascope Corp. be reproduced in any form without permission of Datascope Corp. Panorama WMTS Installation Guide0070-00-0571i Table of Contents Introduction ...................................................................................................................... 1 - 1 Site Survey, Planning and Design...................................................................................................................... 1 - 2 Overview ............................................................................................................................................... 1 - 2 Site Survey, Planning and Design...................................................................................................................... 1 - 3 Tools and Equipment Required .................................................................................................................. 1 - 3 System Installation ........................................................................................................... 2-1 Tools and Equipment Required ......................................................................................................................... 2 - 2 Installing The Wireless Server.................................................................................................................... 2 - 2 Setting Up the TIM Transceiver ......................................................................................................................... 2 - 5 Installing the Antenna Network Components ...................................................................................................... 2 - 6 Panorama Active Antenna ........................................................................................................................ 2 - 6 RF Splitters.............................................................................................................................................. 2 - 6 Connecting the Antenna System to the Wireless Transceiver.......................................................................... 2 - 6 System Configuration........................................................................................................ 3 - 1 Configuring the Wireless Server ....................................................................................................................... 3 - 2 Entering the Wireless Server into the Maintenance Mode ............................................................................. 3 - 2 Assigning the IP Addresses ....................................................................................................................... 3 - 2 Antenna System Calibration.............................................................................................. 4 - 1 Equipment Required ........................................................................................................................................ 4 - 2 Setting a Reference Signal Level ................................................................................................................ 4 - 3 Antenna Calibration ................................................................................................................................ 4 - 4 Programming and Configuring Telemetry Devices ............................................................. 5 - 1 Configuring Bedside Monitors for WMTS telemetry ............................................................................................. 5 - 2 Assigning the Telemetry Server(s) to the Equipment List ........................................................................................ 5 - 2 Programming Telepacks................................................................................................................................... 5 - 3 Instrument Radios ............................................................................................................................................ 5 - 5 Assigning Equipment to the Central Station ........................................................................................................ 5 - 6 Telemetry Devices .................................................................................................................................... 5 - 6 Communication verification .............................................................................................................................. 5 - 7 Frequency Cross Reference................................................................................................ 6 - 1 Appendix A ......................................................................................................................7-1 Appendix B ......................................................................................................................8-1 Table of Contents ii0070-00-0571Panorama WMTS Installation Guide This page intentionally left blank. Panorama WMTS Installation Guide0070-00-05711 - 1 1.0Introduction TBD Site Survey, Planning and DesignIntroduction 1 - 20070-00-0571Panorama WMTS Installation Guide 1.1Site Survey, Planning and Design 1.1.1Overview The telemetry system for the Panorama Central Monitoring System consists of the following major components: • Instrument and Ambulatory Transceivers •Active Antennas • Coaxial Cable and RF Splitters • TIM Transceiver • Panorama Telemetry Server • Panorama Central Station System components will be installed on a full height equipment rack, which should be installed in a secure, climate-controlled area. The antenna system for the Panorama WMTS telemetry is a diversity system. It operates in the 608-614 and 1400 MHz VHF bands. The system receives information from patients in the 608-614 MHz band - the 'uplink'- and transmits informati…

Text truncated - open the document above for the full version.

Cable repeater setup: The cable repeater is configured in two steps. The first is to adjust the gain on each antenna. The second is to adjust the gain between the repeater and the TIM. Step 1- 1.1 Remove jumper J3 in the “A” leg 0670-00-0776-01 board. This will activate the RF tap that is the SMA connector on the 0670-00-0776-01 PCB. 1.2 Using the SMA to SMA cable attach one end to the 0670-00-0776-01 PCB. With a programmed test telepak attach the second SMA to SMA connector to the telepak with the 30dB attunuator in series at the telepak. Attach the other end to the spectrum analyzer using a SMA to N adapter. 1.3 Set the analyzer to span the correct frequency and measure the peak amplitude. Record this value. 1.4 Detach the cable from the spectrum analyzer at the adapter. Attach the cable from the 0670-00-0776-01 PCB to the analyzer. 1.5 Attach the telepak with the cable and attenuator to an antenna on the repeater leg that is on the “A” leg. Adjust the antenna gain such that the spectrum analyzer peak measurement for the frequency is the recorded value minus 1 to 2 dB. Repeat for all antennas on the “A” leg. 1.6 Install the removed jumper to J3. Detach the SMA cable at the 0670-00-0776-01 board. 1.7 Remove jumper J3 in the “B” leg 0670-00-0776-01 board. This will activate the RF tap that is the SMA connector on the 0670-00-0776-01 PCB. 1.8 Attach the SMA cable from the analyzer to the 0670-00-0776-01 PCB . 1.9 Attach the telepak with the cable and attenuator to an antenna on the repeater leg that is on the “B” leg. Adjust the antenna gain such that the spectrum analyzer peak measurement for the frequency is the recorded value minus 1 to 2 dB. Repeat for all antennas on the “A” leg. 1.10 Install the removed jumper to J3. Detach the SMA cable at the 0670-00-0776-01 board. This completes the antenna setup. Step 2- 2.1 Remove the BNC connection of the antenna network from “A” leg on the TIM. 2.2 With the server running WMTS.EXE and displaying the detailed RF list screen, attach the telepak to the TIM using the 30dB attenuator and the SMA to BNC cable. Record the RSSI displayed for the channel that the telepak was assigned. 2.3 Disconnect the cable from the TIM and replace the antenna network cable. 2.4 Detach the SMA to BNC cable from the telepak. Attach a SMA to SMA cable to the telepak with the 30 dB attenuator. Attach the other end of this cable to an antenna on the repeaters “A” leg by removing the antenna stick and attaching the SMA cable. 2.5 Adjust the rotary switch the “A” leg of the cable repeater 0670-00-0776-01 board. Set the gain on the cable repeater to the reading from the TIM with the telepak attached minus 1 to 2 dB. Note: set both switches on the repeater board to the same settings. 2.6 Switch the antenna network “A” leg and “B” leg. 2.7 Attach the other end of this cable to an antenna on the repeaters “B leg. 2.8 Adjust the rotary switch the “B leg of the cable repeater 0670-00-0776-01 board. Set the gain on the cable repeater to the reading from the TIM with the telepak attached minus 1 to 2 dB. Note: set both switches on the repeater board to the same settings. 2.9 Switch the antenna network “A” leg and “B” leg back. 2.10 Detach the telepak and replace the antenna stick. Perform the verification walk around.

September 18, 2004 Telecommunication Certification Body Radio Frequency Investigation Ltd. Ewhurst Park, Ramsdell Basingstoke Hampshire, RG26 5RQ England Subject: Certification Application for Panorama Wireless Transceiver and Panorama Wireless Transceiver with Panorama Cable Repeater FCC ID: DXXVT0190-00000 Dear Sir or Madam: It is requested that the following information is to be held confidential on behalf of Datascope Corp. for the submission of FCC ID: DXXVT0190-00000, FCC Rules Part 0.459 refers. Exhibit A: Overview – memo_receiver_040918.doc (5 pages) and memo_transceiver_040918.doc (5 pages) Exhibit B: Schematics – 0387-00-0745.pdf (48 pages), 0387-00-0776.pdf (5 pages) and 0387-00-0780_r1.pdf (1 page) Exhibit C: Parts List – PL0745revD_.pdf (18 pages), PL0776rev1_.pdf (4 pages) and PL0780rev1_.pdf (2 pages) Exhibit D: Block Diagram – Datascope Panorama Transceiver with repeater block diagram.doc (2 pages) The above material contains trade secrets and the release of this information could result in substantial competitive harm. Datascope Corp. does not want the exhibits mentioned here to be accessible to the general public. The submitting party on the behalf of Datascope Corp. will prevent any unauthorized disclosure and any previous disclosure to the submitting party will not be available to the general public. Yours sincerely, James Fidacaro Project Manager, Senior Principle Engineer Datascope Corp. Patient Monitoring Division 800 MacArthur Blvd. Mahwah, NJ 07430

DS 1DS 2DS 3DS 4 Manufactured by Datascope Corp, Mahwah, NJ 07430 V 100 - 130 ~ A 1.25 Hz 60 ~Fuse: 250V 2.5A Fast-Acting FCC ID: DXXVT0190-00000 P/N S/N ̈ THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION OF THIS DEVICE IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY BE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 0332-00-0238-01 Panorama Transceiver, Rear 8.17.2004 IEC 60950-1:2001 CAN/CSA C22.2 No. 60950-1-03 UL 60950-1:2003 WIRELESS TRANSCEIVER

S/N P/N IEC 60905-1:2001 CAN/CSA C22.2 No. 60950-1-03 UL 60950-1:2003 FCC ID: DXXVT0190-00000 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION OF THIS DEVICE IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY BE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. V 100 - 240 ~ A 0.5 - 0.25 Amp Hz 60 / 50 Manufactured by Datascope Corp, Mahwah, NJ 07430 0334-00-1620 Panorma, Repeater, Info label 9.7.2004 ~ FUSE 1.0 AMP 250 VAc FAST ACTING CAUTION: DOUBLE POLE / NEUTRAL FUSING

August 9, 2004 Telecommunication Certification Body Radio Frequency Investigation Ltd. Ewhurst Park, Ramsdell Basingstoke Hampshire, RG26 5RQ England Subject: Certification Application for Panorama Wireless Transceiver and Panorama Wireless Transceiver with Panorama Cable Repeater FCC ID: DXXVT0190-00000 Dear Sir or Madam: The power output for the Panorama Wireless Transceiver and Panorama Wireless Transceiver with Panorama Cable Repeater is lower than the threshold for the SAR measurements of a portable device operating in the general population experience category. Yours sincerely, James Fidacaro Project Manager, Senior Principle Engineer Datascope Corp. Patient Monitoring Division 800 MacArthur Blvd. Mahwah, NJ 07430

RFI Global Services Ltd, Ewhurst Park, Ramsdell, Basingstoke, Hampshire, RG26 5RQ, ENGLAND. Tel: +44 (0) 1256 851193 Fax: +44 (0) 1256 851192 Registered in England, No. 211 7901. Registered Office: Ewhurst Park, Ramsdell, Basingstoke, Hampshire RG26 5RQ TEST REPORT FROM RFI GLOBAL SERVICES LTD. Test Of: Datascope Corp. Panorama Wireless Transceiver To: FCC Part 95 Subpart H: 2003 Test Report Serial No: RFI/MPTE1/RP46115JD03A This Test Report Is Issued Under The Authority Of Richard Jacklin, Operations Director: Checked By: Tony Henriques Tested By: Steven Wong Release Version No: PDF01 Issue Date: 20 July 2004 Test Dates: 28 June 2004 to 16 July 2004 This report is issued in Adobe Acrobat portable document format (PDF). It is only a valid copy of the report if it is being viewed in PDF format with the following security options not allowed: Changing the document, Selecting text and graphics, Adding or changing notes and form fields. Furthermore, the date of creation must match the issue date stated above. This report may be copied in full. The results in this report apply only to the sample(s) tested. RFI GLOBAL SERVICES LTD. TEST REPORT S.No. RFI/MPTE1/RP46115JD03A Page 2 of 92 Issue Date: 20 July 2004 Test Of: Datascope Corp. Panorama Wireless Transceiver To: FCC Part 95 Subpart H: 2003 This page has been left intentionally blank. RFI GLOBAL SERVICES LTD. TEST REPORT S.No. RFI/MPTE1/RP46115JD03A Page 3 of 92 Issue Date: 20 July 2004 Test Of: Datascope Corp. Panorama Wireless Transceiver To: FCC Part 95 Subpart H: 2003 Table of Contents 1. Client Information ............................................................................................................. 4 2. Equipment Under Test (EUT) ........................................................................................... 5 3. Test Specification, Methods And Procedures................................................................ 9 4. Deviations From The Test Specification....................................................................... 10 5. Operation Of The EUT During Testing .......................................................................... 11 6. Summary Of Test Results .............................................................................................. 12 7. Measurements, Examinations And Derived Results ................................................... 13 8. Test Results: 1395-1400 MHz Downlink Band (Cable Repeater Fitted)...................... 15 9. Test Results: 1427-1429.5 MHz Downlink Band (Cable Repeater Fitted).................. 33 10. Test Results: 1395-1400 MHz Downlink Band (Without Cable Repeater Fitted) ................................................................................................................................... 53 11. Test Results: 1427-1429.5 MHz Downlink Band (Without Cable Repeater Fitted) ................................................................................................................................... 67 13. Measurement Methods – Part 95 ................................................................................. 81 14. Measurement Uncertainty ............................................................................................ 86 Appendix 1. Test Equipment Used .................................................................................... 87 Appendix 2. Test Configuration Drawings ....................................................................... 88 RFI GLOBAL SERVICES LTD. TEST REPORT S.No. RFI/MPTE1/RP46115JD03A Page 4 of 92 Issue Date: 20 July 2004 Test Of: Datascope Corp. Panorama Wireless Transceiver To: FCC Part 95 Subpart H: 2003 1. Client Information Company Name: Datascope Corp. Address: Patient Monitoring Division 800 MacArthur Blvd Mahwah NJ 07430 0619 USA Contact Name: Mr R. Coffin RFI GLOBAL SERVICES LTD. TEST REPORT S.No. RFI/MPTE1/RP46115JD03A Page 5 of 92 Issue Date: 20 July 2004 Test Of: Datascope Corp. Panorama Wireless Transceiver To: FCC Part 95 Subpart H: 2003 2. Equipment Under Test (EUT) The following information (with the exception of the Date of Receipt) has been supplied by the client: 2.1. Identification Of Equipment Under Test (EUT) Description: Transceiver Brand Name: Panorama Wireless Transceiver Model Number: 0998-0190-01 Serial Number: None stated FCC ID DXXVT0190-00000 Country of Manufacture: USA Date of Receipt: 17/05/04 Description: WMTS Antenna (x3) Brand Name: Panorama Model Name or Number: Panorama Antenna Serial number N0104, N0105 and N0106 Country of Manufacture: USA Description: Power Splitter Brand Name: Mini-Circuits Model Name or Number: ZAPD-1450DC75-1 Serial number BE0405590405 Country of Manufacture: USA Description: Repeater RF Amplifier Brand Name: Panorama Repeater Model Name or Number: 0998-00-0703-01 Serial number EP0001 Country of Manufacture: USA RFI GLOBAL SERVICES LTD. TEST REPORT S.No. RFI/MPTE1/RP46115JD03A Page 6 of 92 Issue Date: 20 July 2004 Test Of: Datascope Corp. Panorama Wireless Transceiver To: FCC Part 95 Subpart H: 2003 2.2.Description Of EUT The equipment under test is the fixed transceiver part only of a wireless patient monitor system, designed to operate in the Wireless Medical Telemetry Service . 2.3. Modifications Incorporated In EUT During the course of testing the EUT was not modified. 2.4.Additional Information Related To Testing Power Supply Requirement: 110 V, 60 Hz AC Mains supply Intended Operating Environment: Hospitals Equipment Category: Fixed Type of Unit: Transceiver Interface Ports: DS1; DS2; DS3; DS4; RF A; RF B; AC Mains Transmit Frequency Range 1395 MHz to 1400 MHz & 1427 MHz to 1429.5 MHz Channel ID Channel Number Channel Frequency (MHz) Bottom 1A 1396.2 Transmit Channels Tested (1395 MHz to 1400 MHz band) Top 1B 1398.6 Channel ID Channel Number Channel Frequency (MHz) Bottom 3A 1427.8 Transmit Channels Tested (1427 MHz to 1429.5 MHz band) Top 2B 1428.6 Highest Fundamental Frequency 1428.6 MHz Maximum Fundamental Fieldstr…

Text truncated - open the document above for the full version.