E2K-DWBT3802.11 b/g Wireless LAN mini-card

FCC Radiation Exposure Statement WARNING: The radiated output power of Dell RFID devices is far below the FCC radio frequency exposure limits. Nevertheless, Dell RFID devices should be used in such a manner that the potential for human contact during normal operation is minimized. This device has also been evaluated for and shown compliant with the FCC RF exposure limits under portable exposure conditions (antennas are within 20 cm of a person's body) when installed in certain specific OEM configurations. Details of the authorized configurations can be found at http://www.fcc.gov/oet/fccid/help.html by entering the FCC ID number on the device. Interference Statement These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) The devices must accept any interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures: • Relocate this device. • Increase the separation between the device and the receiver. • Connect the device into an outlet on a circuit different from that of other electronics. • Consult the dealer or an experienced radio technician for help. NOTE: Dell RFID devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment. FCC Radiation Exposure Statement WARNING: The radiated output power of the Dell Wireless WLAN Card devices is far below the FCC radio frequency exposure limits. Nevertheless, the Dell Wireless WLAN Card devices should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20 cm between you (or any other person in the vicinity) and the antenna that is built into the printer. To determine the location of the antenna within your printer, check the information posted on the general Dell support site at http://support.dell.com . This device has also been evaluated for and shown compliant with the FCC RF exposure limits under portable exposure conditions (antennas are within 20 cm of a person's body) when installed in certain specific OEM configurations. Details of the authorized configurations can be found at http://www.fcc.gov/oet/fccid/help.html by entering the FCC ID number on the device. Interference Statement This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Notice: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: • Reorient the receiving antenna. • Relocate the system with respect to the receiver. • Move the system away from the receiver. • Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of Dell Inc. or an experienced radio/television technician for additional suggestions. NOTE: This Dell Wireless WLAN Card must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter.

©©©Úºª¥¥ÚΩ±≥ § ≠ ́∞∞±Æ ̈Úºª¥¥ÚΩ±≥ ‹ª¥¥á ‘ø ̈∑ ̈ ́ºª —“á Õª ̈ ́∞ Ÿ ́∑ºª “± ̈ª≠ “—äÊfl “—ä ∑≤º∑Ωø ̈ª≠ ∑≥∞±Æ ̈ø≤ ̈ ∑≤∫±Æ≥ø ̈∑±≤ ̈∏ø ̈ ∏ª¥∞≠ ß± ́ ≥øμª æª ̈ ̈ªÆ ́≠ª ±∫ ß± ́Æ Ω±≥∞ ́ ̈ªÆÚ ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ ◊≤∫±Æ≥ø ̈∑±≤ ∑≤ ̈∏∑≠ º±Ω ́≥ª≤ ̈ ∑≠ ≠ ́æ∂ªΩ ̈ ̈± Ω∏ø≤πª ©∑ ̈∏± ́ ̈ ≤± ̈∑ΩªÚ wÓÁäÓÔ‹ª¥¥◊≤ΩÚfl¥¥Æ∑π∏ ̈≠ƪ≠ªÆ™ªºÚ Œª∞Ʊº ́Ω ̈∑±≤ ±∫ ̈∏ª≠ª ≥ø ̈ªÆ∑ø¥≠ ∑≤ ø≤ß ≥ø≤≤ªÆ ©∏ø ̈≠±ª™ªÆ ©∑ ̈∏± ́ ̈ ̈∏ª ©Æ∑ ̈ ̈ª≤ ∞ªÆ≥∑≠≠∑±≤ ±∫ ‹ª¥¥ ◊≤ΩÚ ∑≠ ≠ ̈Æ∑Ω ̈¥ß ∫±Ææ∑ººª≤Ú ÃÆøºª≥øÆμ≠ ́≠ªº ∑≤ ̈∏∑≠ ̈ª® ̈Ê ‹ª¥¥Ù ̈∏ª ‹¤‘‘ ¥±π±Ù ø≤º ‘ø ̈∑ ̈ ́ºª—“ øƪ ̈Æøºª≥øÆμ≠ ±∫ ‹ª¥¥ ◊≤ΩÚ ”∑ΩƱ≠±∫ ̈ ø≤º ...∑≤º±©≠ øƪ ª∑ ̈∏ªÆ ̈Æøºª≥øÆμ≠ ±Æ ƪπ∑≠ ̈ªÆªº ̈Æøºª≥øÆμ≠ ±∫ ”∑ΩƱ≠±∫ ̈ ›±Æ∞±Æø ̈∑±≤ ∑≤ ̈∏ª À≤∑ ̈ªºÕ ̈ø ̈ª≠ ø≤ºÒ±Æ ± ̈∏ªÆ Ω± ́≤ ̈Æ∑ª≠ “±™ª¥¥∑≠ ̈∏ª ƪπ∑≠ ̈ªÆªº ̈Æøºª≥øÆμ ±∫ “±™ª¥¥ ◊≤Ω —”fl– ∑≠ ø ̈Æøºª≥øÆμ ±∫ ê®ø≠ ◊≤≠ ̈Æ ́≥ª≤ ̈≠Ú — ̈∏ªÆ ̈Æøºª≥øÆμ≠ ø≤º ̈Æøºª ≤ø≥ª≠ ≥øß æª ́≠ªº ∑≤ ̈∏∑≠ º±Ω ́≥ª≤ ̈ ̈± ƪ∫ªÆ ̈± ª∑ ̈∏ªÆ ̈∏ª ª≤ ̈∑ ̈∑ª≠ Ω¥ø∑≥∑≤π ̈∏ª ≥øÆμ≠ ø≤º ≤ø≥ª≠ ±Æ ̈∏ª∑Æ ∞Ʊº ́Ω ̈≠Ú ‹ª¥¥ ◊≤ΩÚ º∑≠Ω¥ø∑≥≠ ø≤ß ∞Ʊ∞Æ∑ª ̈øÆß ∑≤ ̈ªÆª≠ ̈ ∑≤ ̈Æøºª≥øÆμ≠ ø≤º ̈Æøºª ≤ø≥ª≠ ± ̈∏ªÆ ̈∏ø≤ ∑ ̈≠ ±©≤Ú ”øÆΩ∏ ÓÔŒª™Ú flÓ ›±≤ ̈ª≤ ̈≠Ì ›±≤ ̈ª≤ ̈≠ Ôflæ± ́ ̈ «± ́Æ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Î ⁄ªø ̈ ́ƪ≠ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Î Œªπ ́¥ø ̈±Æß ◊≤∫±Æ≥ø ̈∑±≤ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Í ÓÕª ̈ ̈∑≤π À∞ «± ́Æ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“ Ú Ú Ú Ú Ú Ú Ú È ◊≤≠ ̈ø¥¥∑≤π ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ ›øƺ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú È ¤≤øæ¥∑≤π ‘ø ̈∑ ̈ ́ºª —“ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú È flΩ ̈∑™ø ̈∑≤π ◊≤≠ ̈ø≤ ̈ —“ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú È Õ ̈øÆ ̈∑≤π ‘ø ̈∑ ̈ ́ºª —“Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ë ›±≤∫∑π ́Æ∑≤π ‘ø ̈∑ ̈ ́ºª —“Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ë ¤®∑ ̈∑≤π ‘ø ̈∑ ̈ ́ºª —“ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Á Ì›±≤∫∑π ́Æ∑≤π ̈∏ª “ª ̈©±Æμ Õª ̈ ̈∑≤π≠Ú Ú Ú Ú Ú Ú ÔÔ ¤≤øæ¥∑≤π ̈∏ª ...∑ƪ¥ª≠≠ ±Æ ”±æ∑¥ª fiƱøºæø≤º “ª ̈©±Æμ ∑≤ ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ ”±ºª Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÔ ›±≤≤ªΩ ̈∑≤π ̈± ø ...∑ƪ¥ª≠≠ “ª ̈©±ÆμÚ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÔ ›±≤≤ªΩ ̈∑≤π ̈± ø ”±æ∑¥ª fiƱøºæø≤º “ª ̈©±ÆμÚ Ú Ú Ú Ú Ú ÔÓ ∑ª©∑≤π «± ́Æ ”±æ∑¥ª fiƱøºæø≤º ◊≤∫±Æ≥ø ̈∑±≤ Ú Ú Ú ÔÏ ‹∑≠Ω±≤≤ªΩ ̈∑≤π ∫Ʊ≥ ø ”±æ∑¥ª fiƱøºæø≤º “ª ̈©±ÆμÚ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÏ Ï›±≤ ̈ª≤ ̈≠ flº™ø≤Ωªº “ª ̈©±Æμ ›±≤∫∑π ́Æø ̈∑±≤Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÏ Õª ̈ ̈∑≤π À∞ ø ∑Æ ̈ ́ø¥ –Æ∑™ø ̈ª “ª ̈©±Æμ ̄ –“ ̃ flΩΩ± ́≤ ̈ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÏ ”±º∑∫ß∑≤π «± ́Æ ...∑ƪ¥ª≠≠Ù ”±æ∑¥ª fiƱøºæø≤ºÙ ±Æ –“ ›±≤≤ªΩ ̈∑±≤≠ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÏ ÏÕª ̈ ̈∑≤π À∞ «± ́Æ ‘ø ̈∑ ̈ ́ºª —“ ¤Û≥ø∑¥Ú Ú Ú Ú ÔÎ ›±≤∫∑π ́Æ∑≤π ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ ¤Û≥ø∑¥ ›¥∑ª≤ ̈ Ú Ú Ú Ú Ú Ú Ú ÔÎ flºº∑≤π ±Æ ”±º∑∫ß∑≤π «± ́Æ ¤Û≥ø∑¥ flΩΩ± ́≤ ̈ Ú Ú Ú Ú Ú Ú Ú ÔΠΑø ̈∑ ̈ ́ºª —“ ‹ª≠μ ̈±∞ ◊Ω±≤≠ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÈ ÍÕ∞ªΩ∑∫∑Ωø ̈∑±≤≠ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÔÁ ÈÃƱ ́楪≠∏±± ̈∑≤πÚ Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÓÔ ›±≤ ̈øΩ ̈∑≤𠋪¥¥Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú Ú ÓÌ flæ± ́ ̈ «± ́Æ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“Î flæ± ́ ̈ «± ́Æ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“ ‹ª¥¥á ‘ø ̈∑ ̈ ́ºª —“á ∑≠ ø Ω±≥≥ ́≤∑Ωø ̈∑±≤ ≠±¥ ́ ̈∑±≤ ̈∏ø ̈ ∑≠ ºª≠∑π≤ªº ̈± ∞Ʊ™∑ºª Ø ́∑Ωμ øΩΩª≠≠ ̈± æ ́≠∑≤ª≠≠ÛΩÆ∑ ̈∑Ωø¥ ºø ̈øÚ ‘ø ̈∑ ̈ ́ºª —“ ∏ø≠ ̈∏ª ∞±©ªÆÙ ª∫∫∑Ω∑ª≤ΩßÙ ø≤º ∫¥ª®∑æ∑¥∑ ̈ß ±∫ ̈∏ª —∞ª≤ ” ́¥ ̈∑≥ªº∑ø fl∞∞¥∑Ωø ̈∑±≤ –¥ø ̈∫±Æ≥ ̄—”fl–á ̃ ∞ƱΩª≠≠±Æ ø¥±≤π ©∑ ̈∏ ̈∏ª ́≠øæ∑¥∑ ̈ß ±∫ ø ∞±Æ ̈ø楪 Ω±≥∞ ́ ̈ªÆÚ ‘ø ̈∑ ̈ ́ºª —“ ∑≠ Ω ́Æƪ≤ ̈¥ß ø™ø∑¥ø楪 ±≤ ̈∏ª ∫±¥¥±©∑≤𠋪¥¥ Ω±≥∞ ́ ̈ªÆ≠Ê ü‹ª¥¥ ‘ø ̈∑ ̈ ́ºªá ∆Í ü‹ª¥¥ ‘ø ̈∑ ̈ ́ºª ¤ÏÓ ü‹ª¥¥ ‘ø ̈∑ ̈ ́ºª ¤ÏÌ ü‹ª¥¥ ‘ø ̈∑ ̈ ́ºª ¤ÏÌÔ “—äÊ◊∫ ß± ́ ±ÆºªÆªº ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ Ωøƺ ø¥±≤π ©∑ ̈∏ ß± ́Æ Ω±≥∞ ́ ̈ªÆÙ ̈∏ª ‘ø ̈∑ ̈ ́ºª—“ Ωøƺ ∑≠ ∞ƪÛ∑≤≠ ̈ø¥¥ªº ø≤º øΩ ̈∑™ø ̈ªºÚ ⁄ªø ̈ ́ƪ≠ œ ́∑Ωμ flΩΩª≠≠âfl¥¥±©≠ ß± ́ ̈± øΩΩª≠≠ ªÛ≥ø∑¥Ù Ω±≤ ̈øΩ ̈≠Ù Ωø¥ª≤ºøÆÙ ø≤º©ªæ∞øπª≠Ú ◊≤ ̈ªÆ≤ª ̈ ›±≤≤ªΩ ̈∑±≤ â fl¥¥±©≠ ß± ́ ̈± Ω±≤≤ªΩ ̈ ̈± ̈∏ª ◊≤ ̈ªÆ≤ª ̈ ̈∏Ʊ ́π∏ ©∑ƪ¥ª≠≠ ±Æ ±∞ ̈∑±≤ø¥ ≥±æ∑¥ª æƱøºæø≤º ΩøÆºÚ ¤Û≥ø∑¥ flΩΩ± ́≤ ̈≠ â fl¥¥±©≠ ß± ́ ̈± Ω±≤∫∑π ́ƪ ø≤º øΩΩª≠≠ –—– ø≤º ”∑ΩƱ≠±∫ ̈ r ¤®Ω∏ø≤πª ÓÌ ªÛ≥ø∑¥ øΩΩ± ́≤ ̈≠ ø¥±≤π ©∑ ̈∏ ◊”fl– ø≤º “±™ª¥¥ r πƱ ́∞Û©∑≠ª ªÛ≥ø∑¥ øΩΩ± ́≤ ̈≠Ú «± ́ Ωø≤ ø¥≠± øΩΩª≠≠ ©ªæÛæø≠ªº ªÛ≥ø∑¥ Ω¥∑ª≤ ̈≠ ̈∏Ʊ ́π∏ ̈∏ª ©ªæ æƱ©≠ªÆÚ ÕªΩ ́Æ∑ ̈ß â fl¥¥±©≠ ß± ́ ̈± ≠ª ̈ ́∞ ø ‘ø ̈∑ ̈ ́ºª —“ ≠∞ªΩ∑∫∑Ω ∞ø≠≠©±Æº ø≤º ß± ́ Ωø≤ ø¥≠± Ω¥ªøÆ ̈∏ª ́≠ªÆ ºø ̈øÚ ¤≤∏ø≤Ωªº fiø ̈ ̈ªÆß ‘∑∫ª ⠖Ʊ™∑ºª≠ ª® ̈ª≤ºªº æø ̈ ̈ªÆß ¥∑∫ª ø≠ ̈∏ª ‘ø ̈∑ ̈ ́ºª—“Ωøƺ ∏ø≠ ø≤ ª∫∫∑Ω∑ª≤ ̈ æ ́∑¥ ̈Û∑≤ —”fl– ∞ƱΩª≠≠±ÆÚ ¤ø≠ß À∞πÆøºª â fl¥¥±©≠ ß± ́ ̈± ́∞πÆøºª ̈∏ª ª®∑≠ ̈∑≤π ≠±∫ ̈©øƪ ∫±Æ øºº∑ ̈∑±≤ø¥ ≠ªΩ ́Æ∑ ̈ßÙ –“ ≠ ́∞∞±Æ ̈ ª≤ΩÆß∞ ̈∑±≤Ù ø≤º ø∞∞¥∑Ωø ̈∑±≤≠ ©∏ª≤ ̈∏ªß øƪ ø™ø∑¥ø楪 ́≠∑≤π ø ∫¥ø≠∏ ́ ̈∑¥∑ ̈ßÚ Íflæ± ́ ̈ «± ́Æ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“ Œªπ ́¥ø ̈±Æß ◊≤∫±Æ≥ø ̈∑±≤ ⁄±Æ øºº∑ ̈∑±≤ø¥ ƪπ ́¥ø ̈±Æß ∑≤∫±Æ≥ø ̈∑±≤Ù ≠ªª ̈∏ª Œªπ ́¥ø ̈±Æß ›±≥∞¥∑ø≤Ωª ÿ±≥ª∞øπª ±≤ ©©©Úºª¥¥ÚΩ±≥ ø ̈ ̈∏ª ∫±¥¥±©∑≤π ¥±Ωø ̈∑±≤Ê ©©©Úºª¥¥ÚΩ±≥Òƪπ ́¥ø ̈±Æß¡Ω±≥∞¥∑ø≤ΩªÚ Õª ̈ ̈∑≤π À∞ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“È Õª ̈ ̈∑≤π À∞ «± ́Æ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“ ◊≤≠ ̈ø¥¥∑≤π ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ ›øƺ “—äÊ◊∫ ß± ́ ±ÆºªÆªº ø ‹ª¥¥á ‘ø ̈∑ ̈ ́ºª —“á Ωøƺ ø¥±≤π ©∑ ̈∏ ß± ́Æ Ω±≥∞ ́ ̈ªÆÙ ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ Ωøƺ ∑≠ ∞ƪÛ∑≤≠ ̈ø¥¥ªº ±≤ ß± ́Æ Ω±≥∞ ́ ̈ªÆÚ Ã± ∑≤≠ ̈ø¥¥ ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ Ωøƺ٠≠ªª ̈∏ª ◊≤≠ ̈ø¥¥∑≤π «± ́Æ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“ ›øƺ ̈∏ø ̈ ≠∏∑∞∞ªº ©∑ ̈∏ ß± ́Æ ‘ø ̈∑ ̈ ́ºª —“ ΩøÆºÚ “—äʑø ̈∑ ̈ ́ºª —“ ∑≠ ø¥Æªøºß ∑≤≠ ̈ø¥¥ªº ±≤ ̈∏ª ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª ∆Í Ω±≥∞ ́ ̈ªÆÚ ¤≤øæ¥∑≤π ‘ø ̈∑ ̈ ́ºª —“ “—äÊ◊∫ ß± ́ ±ÆºªÆªº ø ‘ø ̈∑ ̈ ́ºª —“ Ωøƺ ©∑ ̈∏ ß± ́Æ Ω±≥∞ ́ ̈ªÆÙ ̈∏ª ‘ø ̈∑ ̈ ́ºª —“ ∫ªø ̈ ́ƪ ∑≠ ø¥Æªøºß ª≤ø楪ºÚ Ô Ã ́Æ≤ ±≤ ̄±Æ ƪ≠ ̈øÆ ̈ ̃ ß± ́Æ Ω±≥∞ ́ ̈ªÆÚ Ó...∏ª≤ ̈∏ª ‹ª¥¥ ¥±π± ø∞∞ªøÆ≠Ù ©ø∑ ̈ ∫±Æ ̈∏ª ⁄Ó ∞Ʊ≥∞ ̈ ̈± ø∞∞ªøÆ ø≤º ∞ƪ≠≠‰⁄Ó‚ ∑≥≥ªº∑ø ̈ª¥ßÚ Ã∏ª fi◊—Õ ≠Ωƪª≤ ø∞∞ªøÆ≠Ú Ì›∏±±≠ªÕß≠ ̈ª≥ ›±≤∫∑π ́Æø ̈∑±≤‘ø ̈∑ ̈ ́ºª —“Ú ÏÕª¥ªΩ ̈ ̈∏ª ¤≤ø楪 ‘ø ̈∑ ̈ ́ºª —“ Ω∏ªΩμ æ±®Ú Î›¥∑Ωμfl∞∞¥ß ø≤º Ω¥∑Ωμ ¤®∑ ̈ ̈± ƪ≠ ̈øÆ ̈ ̈∏ª Ω±≥∞ ́ ̈ªÆÚ flΩ ̈∑™ø ̈∑≤π ◊≤≠ ̈ø≤ ̈ —“ Ôà ́Æ≤ ±≤ ̄±Æ ƪ≠ ̈øÆ ̈ ̃ ß± ́Æ Ω±≥∞ ́ ̈ªÆÚ Ó...∏ª≤ ̈∏ª ‹ª¥¥ ¥±π± ø∞∞ªøÆ≠Ù ©ø∑ ̈ ∫±Æ ̈∏ª ⁄Ó ∞Ʊ≥∞ ̈ ̈± ø∞∞ªøÆ ø≤º ∞ƪ≠≠‰⁄Ó‚ ∑≥≥ªº∑ø ̈ª¥ßÚ Ã∏ª fi◊—Õ ≠Ωƪª≤ ø∞∞ªøÆ≠Ú Ì›∏±±≠ªÕß≠ ̈ª≥ ›±≤∫∑π ́Æø ̈∑±≤‘ø ̈∑ ̈ ́ºª —“Ú ÏÕª¥ªΩ ̈ ̈∏ª ¤≤ø楪 ◊≤≠ ̈ø≤ ̈ —“ Ω∏ªΩμ æ±®Ú Î›¥∑Ωμfl∞∞¥ß ø≤º Ω¥∑Ωμ ¤®∑ ̈ ̈± ƪ≠ ̈øÆ ̈ ̈∏ª Ω±≥∞ ́ ̈ªÆÚ ËÕª ̈ ̈∑≤π À∞ ‹ª¥¥ ‘ø ̈∑ ̈ ́ºª —“ Õ ̈øÆ ̈∑≤π ‘ø ̈∑ ̈ ́ºª —“ “—äÊ...∏ª≤ ß± ́Æ Ω±≥∞ ́ …

Text truncated - open the document above for the full version.

One Dell Way Round Rock, TX 78682, United States February 26, 2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Subject: Short-term confidentiality request regarding application for Certification of FCC ID: E2K-DWBT3 To whom it may concern: Pursuant to DA 04-1705 of the Commission’s public notice, we request short- term confidential treatment for the following information until July 26, 2010 after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: • External Photos • Test Setup Photos • User’s Manual • Internal Photos Sincerely, Thanh Nguyen Dell Inc. TEL: 512-723-8862 E-Mail: [email protected]

Applicant/Grantee Dell Computer Corporation FCC ID: E2KDWBT3 Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Device is equipped with Metal shielding to cover RF section. Refer to external photos. Y 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. All inputs to the modules are buffered through logic or microprocessor inputs. Y 3 The modular transmitter must have its own power supply regulation. The mini-pci interface provides 3.3VDC, so there are rgulator in fron to these chips. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Refer to antenna specification and test report. Y 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no cou pling between The EUT was test in Notebook Computer (Brand name: DELL; Model: P05G). Please see section Photographs of Test Configuration in the test report. Y the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. Refer to label format and location file. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the a pplication for equipment Detail instructions for maintaining compliance are given in the Users Manual. Y authorization. 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. Signature: _________________________ NAME: Steven Wang TITLE: Section Manager Date: March 10, 2010 TESTING LABORATORY: Compliance Certification Services…

Text truncated - open the document above for the full version.

Date: March 9, 2010 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Mr. Steven Wang / Section Manager of Compliance Certification Services Inc. and hereafter referred to as CCS , to act on our behalf in all manners relating to application for equipment authorization of FCC id E2K-DWBT3 , including signing of all documents relating to these matters. Any and all acts carried out by Mr. Steven Wang / Section Manager of Compliance Certification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Thanh Nguyen/ Wireless Regulatory Engineer DELL Inc. 512-723-8862 E-MAIL :[email protected] REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

Dell Inc. Richard Worley, NCE MS: PS4-30 EMC, Global Regulations and Standards One Dell Way Telephone 512.728.1081 Round Rock, Texas 78682 Telefax 512.283.9268 www.dell.com e-mail [email protected] March 10, 2010 To whom it may concern, I, the undersigned, as the authorized signatory for the Dell Inc grantee code E2K, hereby authorize Thanh Nguyen, EMC & Wireless Regulatory Engineering of Dell Inc., to act on my behalf in all manners relating to application (FCC ID: E2K-DWBT3) for equipment authorization, including signing of all documents relating to this application. Any and all acts carried out by Thanh Nguyen of Dell Inc. on our behalf shall have the same effects as acts of our own. This authorization shall be sent along with application when filing with the FCC Certification Division and is valid until further written notice from the applicant. If you have any questions or need additional information, please feel free to contact me at 512- 728-1081 or 512-431-1084. Sincerley, Richard Worley Dell Inc. FRN: 0008359580

One Dell Way Round Rock, TX 78682, United States Date: March 11, 2010 FCC ID: E2K-DWBT3 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Part List Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Thanh Nguyen Dell Inc. TEL: 512-723-8862 E-Mail: [email protected]

Report No: 91218101 Page 1 / 5 EXTERNAL PHOTOGRAPHS OF EUT Report No: 91218101 Page 2 Report No: 91218101 Page 3 Report No: 91218101 Page 4 Report No: 91218101 Page 5

Report No: 91218101 Page 1 / 6 INTERNAL PHOTOGRAPHS OF EUT Report No: 91218101 Page 2 Antenna Location Report No: 91218101 Page 3 RF Module Report No: 91218101 Page 4 Report No: 91218101 Page 5 Report No: 91218101 Page 6 Antenna

Report No: 91218101-RP1 FCC ID: E2K-DWBT3 Date of Issue: March 3, 2010 Page 1 / 61 FCC 47 CFR PART 15 SUBPART C TEST REPORT For 802.11 b/g Wireless LAN mini-card Model: DWBT3 Trade Name: DELL Issued to Dell Computer Corporation ONE DELL WAY, ROUND ROCK, TEXAS 78682, U.S.A. Issued by Compliance Certification Services Inc. No. 81-1, Lane 210, Pa-De 2nd Rd., Luchu Hsiang, Taoyuan Shien, (338) Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 http://www.ccsrf.com [email protected] Report No: 91218101-RP1 FCC ID: E2K-DWBT3 Date of Issue: March 3, 2010 Page 2 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Revision History Rev. Issue Date Revisions Effect Page Revised By 00 March 3, 2010 Initial Issue ALL Jill Shiau Report No: 91218101-RP1 FCC ID: E2K-DWBT3 Date of Issue: March 3, 2010 Page 3 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION........................................................................................... 4 2 EUT DESCRIPTION ............................................................................................................... 5 3 TEST METHODOLOGY ......................................................................................................... 6 3.1. EUT CONFIGURATION .................................................................................................... 6 3.2. EUT EXERCISE ................................................................................................................ 6 3.3. GENERAL TEST PROCEDURES ..................................................................................... 6 3.4. FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ......................................... 7 3.5. DESCRIPTION OF TEST MODES .................................................................................... 8 4 INSTRUMENT CALIBRATION............................................................................................... 9 4.1. MEASURING INSTRUMENT CALIBRATION ................................................................... 9 4.2. MEASUREMENT EQUIPMENT USED ............................................................................. 9 4.3. MEASUREMENT UNCERTAINTY .................................................................................. 10 5 FACILITIES AND ACCREDITATIONS................................................................................. 11 5.1 FACILTIES....................................................................................................................... 11 5.2 EQUIPMENT ................................................................................................................... 11 5.3 TABLE OF ACCREDITATIONS AND LISTINGS............................................................. 12 6 SETUP OF EQUIPMENT UNDER TEST.............................................................................. 13 6.1. SETUP CONFIGURATION OF EUT ............................................................................... 13 6.2. SUPPORT EQUIPMENT ................................................................................................. 13 7 FCC PART 15.247 REQUIREMENTS .................................................................................. 14 7.1. 6 DB BANDWIDTH ........................................................................................................... 14 7.2. PEAK POWER................................................................................................................. 18 7.3. AVERAGE POWER ......................................................................................................... 22 7.4. BAND EDGES MEASUREMENT .................................................................................... 26 7.5. PEAK POWER SPECTRAL DENSITY ............................................................................ 35 7.6. SPURIOUS EMISSIONS ................................................................................................. 39 7.7. POWERLINE CONDUCTED EMISSIONS ...................................................................... 53 APPENDIX I RADIO FREQUENCY EXPOSURE ....................................................................... 56 APPENDIX II PHOTOGRAPHS OF TEST SETUP..................................................................... 58 Report No: 91218101-RP1 FCC ID: E2K-DWBT3 Date of Issue: March 3, 2010 Page 4 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. 1 TEST RESULT CERTIFICATION Applicant: Dell Computer Corporation ONE DELL WAY, ROUND ROCK, TEXAS 78682, U.S.A. Equipment Under Test: 802.11 b/g Wireless LAN mini-card Trade Name: DELL Model: DWBT3 Date of Test: December 18, 2009 ~ February 26, 2010 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. Approved by: Reviewed by: Ethan Huang Section Manager Stan Lin Supervisor Report No: 91218101-RP1 FCC ID: E2K-DWBT3 Date of Issue: March 3, 2010 Page 5 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. 2 EUT DESCRIPTION Product 802.11 b/g Wireless LAN mini-card Trade Name DELL Model Number DWBT3 Power Supply Powered form DC Source Operating Frequency Range 2412 ~ 2462 MHz Transmit Power IEEE 802.…

Text truncated - open the document above for the full version.

Report No: 91218101-RP1 FCC ID: E2K-DWBT3 Date of Issue: March 3, 2010 Page 58 …

Text truncated - open the document above for the full version.