E2K-DWRFID2002RFID 13.56MHz Wireless Module

FCC Radiation Exposure Statement WARNING: The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, this device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the FCC RF Exposure limits under mobile exposure conditions (antennas are greater than 20cm from a person’s body). This device has also been evaluated for and shown compliant with the FCC RF exposure limits under portable exposure conditions (antennas are within 20 cm of a person's body) when installed in certain specific configurations. Details of the authorized configurations can be found at https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID number on the device. Interference Statement These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) The devices must accept any interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:  Relocate this device.  Increase the separation between the device and the receiver.  Connect the device into an outlet on a circuit different from that of other electronics.  Consult the dealer or an experienced radio technician for help. NOTE: Dell RFID devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment.

OEM Installation Guidance For Dell RFID 13.56MHz Wireless Module, FCC ID: E2K‐DWRFID2002, IC: 1514B‐DWRFID2002 ‐ OEM integrators must ensure that its product is electrically identical to Dell’s reference designs. Any modifications to Dell’s reference designs may invalidate regulatory approvals in relation to the product, or may necessitate notifications to the relevant regulatory authorities. ‐ OEM integrators are responsible for regression testing to accommodate changes to designs, new antennas, and host and submit for C2PC filings. Colocation with other transmitter modules will be addressed through filings for those co‐located transmitters when necessary or that colocation of other transmitters will be according to applicable KDB guidelines including those for RF exposure ‐The final system integrator must ensure there is no instruction provided in the user manual or customer documentation indicating how to install or remove the transmitter ‐ Appropriate labels must be affixed to the product that complies with applicable regulations in all respects. The regulatory label on the final system must include the statement: “Contains FCC ID: E2K‐ DWRFID2003 and/or IC: 1514B‐ DWRFID2003”. ‐ A user’s manual or instruction manual must be included with the product that contains the text as required by applicable law shall be provided to OEM integrators. They may include: 1. USA—Federal Communications Commission (FCC) FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: ‐Reorient or relocate the receiving antenna ‐Increase the distance between the equipment and the receiver. ‐Connect the equipment to outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The final host manual shall include the following regulatory statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: ‐Reorient or relocate the receiving antenna ‐Increase the distance between the equipment and the receiver. ‐Connect the equipment to outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Canada ‐ Industry Canada (IC) This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French: Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L‘utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. FCC Rule parts 15.225 The modular transmitter is only FCC authorized for the specific rule parts 15.225 listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The modular transmitter NO its own RF shielding, and tested inside of a host device Portable Computer ‐ Tablet. (Brand: DELL, Model: T04H) The Antenna information Antenna Antenna Manufacturer Antenna Model No. Antenna Type Note NFC Antenna HongBo DC33002GR3L (260‐24337) Loop antenna Main source NFC Antenna WNC DC33002HP1L (81EABH15.G01) Loop antenna 2 nd source The test modes and testing requirements please refer to DWRFID2002 test reports

| | / Quick Start 快速入门 | 快速啟動 | Démarrage rapide | Quick Start Mulai Cepat | クイックスタート | 빠른 시작 | Início rápido Руководство по быстрому началу работы | Початок роботи Brzi početak | Brzo pokretanje | Inicio rápido التشغیل السریع התחלה מהירה Regulatory Model/Type 管制型号/类型 | 管制型號/類型 | Type/Modèle réglementaire | Vorschriftenmodell/-Typ | Tipe/Model Resmi 規制モデル / タイプ | 규정 모델/유형 | Tipo ou modelo de normalização Нормативная модель/тип | Модель/тип за нормативами | Regulatorni model/tip Regulatorni model/tip Modelo/tipo regulatorio النوع/الطراز الرقابي דגם/סוג תקינה Información para NOM, o Norma Oficial Mexicana La información que se proporciona a continuación se mostrará en los dispositivos que se describen en este documento, en conformidad con los requisitos de la Norma Oficial Mexicana (NOM): Importador: Dell México, S.A. de C.V Av. Javier Barros Sierra, no 540, Piso 10, Col. Lomas de Santa Fe Delegación Álvaro Obregón, Ciudad de México. C.P. 01219 R.F.C: DME9204099R6 País de origen: Hecho en China MCMC certification mark Windows In Windows Search, type System. In the search results, click System. Ubuntu On the desktop, click →About This Computer. Di impor oleh: PT Dell Indonesia Menara BCA Lantai 48 Unit 4804 Jalan M.H Thamrin No. 1 Jakarta Pusat, 10310 Indonesia Connection and use of this communications equipment is permitted by the Nigerian Communications Commission. 商品名稱： 型號： 額定電壓： 伏特 額定頻率： 赫茲 額定輸入電流： 安培 製造年份：參考外箱標示或條碼標籤 製造號碼：參考條外箱條碼標籤 生產國別：參考外箱標示 注意事項：參考使用手冊 產品功能：參考使用手冊 緊急處理方法：參考使用手冊 進口商/委製商：荷蘭商戴爾企業股份有限公司台灣分公司 進口商/委製商地址：台北市敦化南路二段 218 號 20 樓 進口商/委製商電話：00801-861-011 本產品符合臺灣RoHS標準CNS15663, 請見 http://www.dell.com/learn/tw/zh/twcorp1/envt-info-materials Read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at Dell.com/regulatory_compliance . 请阅读您计算机随附的安全信息。有关其他安全方面的最佳实践信息，请参阅 Dell.com/regulatory_compliance 上的“合规性”主页。 請閱讀電腦隨附的安全資訊。 關於其他最佳安全實作的資訊，請參閱 Regulatory Compliance Homepage (法規遵循首頁) 於 Dell.com/regulatory_compliance。 Lisez les consignes de sécurité livrées avec votre ordinateur. Pour des informations supplémentaires sur les pratiques d'excellence, reportez-vous à la page d'accueil de la conformité aux réglementations sur Dell.com/regulatory_compliance. Weitere Informationen bieten die im Lieferumfang des Computers enthaltenen Sicherheitshinweise. Um zusätzliche Informationen zur bestmöglichen Einhaltung der Sicherheitsrichtlinien zu erhalten, sehen Sie die dazugehörige Homepage unter Dell.com/regulatory_compliance. Lihat informasi keselamatan yang disertakan dengan komputer Anda. Untuk informasi praktik keselamatan tambahan, kunjungi Laman Pemenuhan Peraturan di Dell.com/regulatory_compliance. コンピュータに同梱の安全に関する注意事項をお読みください。安全にお使いいただくためのベストプラクティスの追加情報に関しては、Dell.com/regulatory_compliance の規制順守に関するホームペ ージを参照してください。 컴퓨터와 함께 제공된 안전 정보를 읽으십시오. 안전 우수사례와 관련한 추가 정보는, Dell.com/regulatory_compliance 의 규정 준수(Regulatory Compliance) 웹 사이트를 참조하십시오. Leia as informações de segurança fornecidas com o seu computador. Para obter mais informações sobre as boas práticas de segurança, consulte o site de conformidade normativa em Dell.com/regulatory_compliance . Ознакомьтесь с информацией о безопасности, поставляемой с вашим компьютером. Для получения дополнительных сведений о передовых практических методах по технике безопасности посетите домашнюю страницу соответствия нормативным требованиям на веб-узле Dell.com/regulatory_compliance. Ознайомтеся з паспортом безпеки, що входить до комплекту постачання комп'ютера. Додаткові відомості про техніку безпеки див. на головній сторінці розділу про відповідність нормативам за веб-адресою Dell.com/regulatory_compliance. Pročitajte bezbednosne informacije koje ste dobili uz računar. Za dodatne informacije o najboljoj bezbednosnoj praksi pogledajte početnu stranicu za usklađenost sa odredbama na adresi Dell.com/regulatory_compliance. Pročitajte bezbednosne informacije koje ste dobili uz računar. Za dodatne informacije o najboljim bezbednosnim praksama, pogledajte početnu stranicu za usklađenost sa propisima na Dell.com/regulatory_compliance. Lea la información de seguridad enviada con el equipo. Para obtener información adicional sobre las mejores prácticas de seguridad, consulte la Página principal de conformidad reglamentaria en Dell.com/regulatory_compliance. اقرأ معلومات الأمان الواردة مع الكمبیوتر. لإیجاد معلومات إضافیة حول أفضل ممارسات السلامة، انظر انظر الصفحة الرئیسیة لقسم Regulatory Compliances علي الموقع latory_complianceDell.com/regu. קרא את המידע בנושא בטיחות המצורף למחשב .לעיון במידע על נהלים מומלצים נוספים בנושא בטיחות ,ראה את דף הבית בנושא תאימות תקינה בכתובת Dell.com/regulatory_compliance. Do not remove the computer cover unless you need to install internal accessories for your computer. For instructions on removing and replacing parts, see the Owner’s or Service Manual at Dell.com/support. 除非您需要安装计算机内部附件，否则请勿卸除计算机主机盖。有关卸除和更换部件的说明，请参阅位于Dell.com/support 上的《用户手册》或《服务手册》。 除非您需要為您的電腦安裝內部配件，否則請勿拆卸電腦外蓋。有關拆卸和更換零件的說明，請參閱Dell.com/support 上的擁有者手冊或維修手冊。 Ne retirez pas le capot de l'ordinateur à moins que vous ne deviez installer des accessoires internes à votre ordinateur. Pour obtenir des instructions sur le remplacement des pièces, reportez-vous au Guide de l'utilisateur ou au Guide de maintenance à l'adresse Dell.com/support. Entfernen Sie die Computerabdeckung nur dann, wenn Sie das interne Zubehör für Ihren Computer einbauen müssen. Weitere Informationen zum Entfernen und Austauschen von Komponenten finden Sie im Benutzer- oder Service-Handbuch unter Dell.com/support. Jangan lepaskan penutup komputer kecuali Anda perlu memasang aksesori internal untuk komputer. Untuk petunjuk mengenai cara melepaskan dan memasang kembali komponen, lihat Panduan Layanan atau Panduan Pemilik di Dell.com/support. コンピュータの内部アクセサリを取り付ける必要がない限り、コンピュータのカバーを取り外さないでください。部品の取り外しおよび取り付け手順については、 Dell.com/support の 「オーナーズマニュアル」または「サービスマニュアル」を参照してください。 컴퓨터의 내장 액세서리를 장착해야 하는 경우를 제외하고 컴퓨터 덮개를 분리하지 마십시오.…

Text truncated - open the document above for the full version.

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution:  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. * Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Industry Canada statement  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.  This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios.  Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées. Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.

Dell Inc. One Dell Way, Round Rock, Texas 78682, USA Date: 2020-12-09 FCC ID: E2K-DWRFID2002 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: Dell Inc. hereby authorizes Debby Lin/ Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Debby Lin/ Senior Specialist of BV CPS Taoyuan on Dell Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- William Wei, Regulatory Compliance Engineer Dell Inc. Tel: +886-2- 23766556 Fax: +886-2- 23769435 E-mail: [email protected]

Dell Inc. Don Bobo MS: PS4-30 Distingished Member of Technical Staff One Dell Way EMC, Global Regulations and Standards Round Rock, Texas 78682 Telephone 512.728.5508 www.dell.com e-mail [email protected] Worldwide Regulatory Compliance Engineering & Environmental Affairs Internal Use - Confidential Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 April 16, 2020 FCC authorization letter for Dell Regulatory employees To whom it may concern, I, the undersigned, as the authorized signatory for the Dell Inc. grantee code E2K, hereby authorize the following EMC & Wireless Regulatory Engineers of Dell Inc., to act on my behalf in all manners relating to processes required according to FCC rules for equipment authorization: This authorization shall be sent along with application when filing with the FCC Certification Division and is valid until further written notice from the applicant. If you have any questions or need additional information, please feel free to contact me at 512-728-5508 or 512-619-7976. Sincerely, Don Bobo, Dell Inc., FRN: 0008359580 Adele Huang Angelica Chang Fiona Y Chen Kay Chen Jane YC Chen Jessie Goh Jack TS Huang Tommy Hwang Nai Ghee Koh Jason KP Lee Jason Limoges Leonel Lopez James V Nguyen Rex Wan Zenon Wang William Wei Steve L Williams Jim Wu Amber Peng Anna TA Lin

Dell Inc. One Dell Way, Round Rock, Texas 78682, USA Date: 2020-12-09 FCC ID: E2K-DWRFID2002 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------------------- William Wei, Regulatory Compliance Engineer Dell Inc. Tel: +886-2- 23766556 Fax: +886-2-23769435 E-mail: [email protected]

Dell Inc. One Dell Way, Round Rock, Texas 78682, USA Date: 2020-12-09 FCC ID: E2K-DWRFID2002 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 2021/4/2 in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------------------- William Wei, Regulatory Compliance Engineer Dell Inc. Tel: +886-2- 23766556 Fax: +886-2-23769435 E-mail: [email protected]

FCC ID: E2K-DWRFID2002 Report No.: RFBEDW-WTW-P20110459 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch December 22, 2020 Dear Application Examiner, Dell Inc., RFID 13.56MHz Wireless Module , FCC ID: E2K-DWRFID2002 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip DWRFID2002. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is DWRFID2002. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: E2K-DWRFID2002 Report No.: RFBEDW-WTW-P20110459 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Debby Lin Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Reference No.: BEDW-WTW-P20110459_EXT 1 of 8 CONSTRUCTION PHOTOS OF EUT Brand: DELL / Model: DWRFID2002 Reference No.: BEDW-WTW-P20110459_EXT 2 of 8 (End-product: Brand: DELL / Model: T04H) Reference No.: BEDW-WTW-P20110459_EXT 3 of 8 Reference No.: BEDW-WTW-P20110459_EXT 4 of 8 Reference No.: BEDW-WTW-P20110459_EXT 5 of 8 Reference No.: BEDW-WTW-P20110459_EXT 6 of 8 Reference No.: BEDW-WTW-P20110459_EXT 7 of 8 Reference No.: BEDW-WTW-P20110459_EXT 8 of 8

Label & Label Location DELL Model:T04H, Laser etching on Back cover Contains FCC ID: E2K-DWRFID2002 Contains IC: 1514B-DWRFID2002 Label Location Label Location

DWRFID2002 RFID Label Location Label Drawing RFID module RFID Antenna LABEL

Reference No.: BEDW-WTW-P20110459_INT 1 of 7 CONSTRUCTION PHOTOS OF EUT Brand: DELL / Model: DWRFID2002 Reference No.: BEDW-WTW-P20110459_INT 2 of 7 (End-product: Brand: DELL / Model: T04H) Reference No.: BEDW-WTW-P20110459_INT 3 of 7 Reference No.: BEDW-WTW-P20110459_INT 4 of 7 Reference No.: BEDW-WTW-P20110459_INT 5 of 7 Reference No.: BEDW-WTW-P20110459_INT 6 of 7 Reference No.: BEDW-WTW-P20110459_INT 7 of 7

Report No.: SABEDW-WTW-P20110459 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SABEDW-WTW-P20110459 FCC ID: E2K-DWRFID2002 Test Model: DWRFID2002 Received Date: Nov. 14, 2020 Date of Evaluation: Dec. 08, 2020 Issued Date: Dec. 11, 2020 Applicant: Dell Inc. Address: One Dell Way, Round Rock, Texas 78682, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SABEDW-WTW-P20110459 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Evaluation Result .................................................................................................................................. 5 3 SAR Test Exclusion Thresholds .......................................................................................................... 6 4 Conclusion ............................................................................................................................................ 6 Report No.: SABEDW-WTW-P20110459 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SABEDW-WTW-P20110459 Original Release Dec. 11, 2020 Report No.: SABEDW-WTW-P20110459 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: RFID 13.56MHz Wireless Module Brand: DELL Test Model: DWRFID2002 Sample Status: Production Unit Applicant: Dell Inc. Date of Evaluation: Dec. 08, 2020 Standards: References Test Guidance : FCC Part 2 (Section 2.1091) KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.3 -2002 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data eval…

Text truncated - open the document above for the full version.