E2K-DWRFID2004NFC Wireless Charging Module

FCC Radiation Exposure Statement WARNING: The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, this device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the FCC RF Exposure limits under mobile exposure conditions (antennas are greater than 20cm from a person’s body). This device has also been evaluated for and shown compliant with the FCC RF exposure limits under portable exposure conditions (antennas are within 20 cm of a person's body) when installed in certain specific configurations. Details of the authorized configurations can be found at https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID number on the device. Interference Statement These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) The devices must accept any interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:  Relocate this device.  Increase the separation between the device and the receiver.  Connect the device into an outlet on a circuit different from that of other electronics.  Consult the dealer or an experienced radio technician for help. NOTE: Dell RFID devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment.

FCC Radiation Exposure Statement WARNING: The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, this device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the FCC RF Exposure limits under mobile exposure conditions (antennas are greater than 20cm from a person’s body). This device has also been evaluated for and shown compliant with the FCC RF exposure limits under portable exposure conditions (antennas are within 20 cm of a person's body) when installed in certain specific configurations. Details of the authorized configurations can be found at https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID number on the device. Interference Statement These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) The devices must accept any interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:  Relocate this device.  Increase the separation between the device and the receiver.  Connect the device into an outlet on a circuit different from that of other electronics.  Consult the dealer or an experienced radio technician for help. NOTE: Dell RFID devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures The EUT was tested inside a specific platform (model: DELL; Brand: T05J) and limited modular approval for this specific platform. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. Antenna Type coil 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: E2K-DWRFID2004”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manu…

Text truncated - open the document above for the full version.

DELL INC. One Dell Way Round Rock, Texas 78682 United States Applicant: DELL INC. FCC ID: E2K-DWRFID2004 RF Exposure Requirements ( FCC KDB 680106 D01 V03) Requirements Statements (a) Power transfer frequency is less that 1 MHz 13.56MHz, refer FCC (Tracking Number 670317) (b) Output power from each primary coil is less than 15 watts 1 watts (c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils Single coil (d) Client device is inserted in or placed directly in contact with the transmitter Client device is placed directly in contact with the transmitter (e) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). NA (f) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. This is portable device, SAR shall be used to evaluate exposure to RF from 100kHz to 6GHz and test distance is 0 cm. ----------------------------------------------- Zenon Wang Dell | GPC & EA (Global Product Compliance and Environmental Affairs), RCE (Regulatory Compliance Engineer) Dell EMC | GPCE & EA Office+ 886 2 2376 6810 Mail: [email protected]

DELL INC. One Dell Way Round Rock, Texas 78682 United States Date: 2022-03-15 FCC ID: E2K-DWRFID2004 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: DELL INC. hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on DELL INC.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Zenon Wang Dell | GPC & EA (Global Product Compliance and Environmental Affairs), RCE (Regulatory Compliance Engineer) Office+ 886 2 2376 6810 Mail: [email protected]

Dell Inc. Don Bobo MS: PS4-30 Distingished Member of Technical Staff One Dell Way EMC, Global Regulations and Standards Round Rock, Texas 78682 Telephone 512.728.5508 www.dell.com e-mail [email protected] Worldwide Regulatory Compliance Engineering & Environmental Affairs Internal Use - Confidential Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 December 13, 2021 FCC authorization letter for Dell Regulatory employees To whom it may concern, I, the undersigned, as the authorized signatory for the Dell Inc. grantee code E2K, hereby authorize the following EMC & Wireless Regulatory Engineers of Dell Inc., to act on my behalf in all manners relating to processes required according to FCC rules for equipment authorization: This authorization shall be sent along with application when filing with the FCC Certification Division and is valid until further written notice from the applicant. If you have any questions or need additional information, please feel free to contact me at 512-593-8560 or 512-619-7976. Sincerely, Don Bobo, Dell Inc., FRN: 0008359580 Adele Huang Angelica Chang Fiona Y Chen Kay Chen Jane YC Chen Jessie Goh Jack TS Huang Tommy Hwang Nai Ghee Koh Jason KP Lee Jason Limoges Leonel Lopez James V Nguyen Rex Wan Zenon Wang William Wei Steve L Williams Jim Wu Amber Peng Leo Hong Dyllan Chang Ken Tai CY Chang Maurice Wu Greg Hsiao

DELL INC. One Dell Way Round Rock, Texas 78682 United States Date: 2022-03-15 FCC ID: E2K-DWRFID2004 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Zenon Wang Dell | GPC & EA (Global Product Compliance and Environmental Affairs), RCE (Regulatory Compliance Engineer) Office+ 886 2 2376 6810 Mail: [email protected]

DELL INC. One Dell Way Round Rock, Texas 78682 United States Date: 2022-04-13 FCC ID: E2K-DWRFID2004 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 2 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Zenon Wang Dell | GPC & EA (Global Product Compliance and Environmental Affairs), RCE (Regulatory Compliance Engineer) Office+ 886 2 2376 6810 Mail: [email protected]

FCC ID: E2K-DWRFID2004 Report No.: RFXXXXXXXX Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch April 12, 2022 Dear Application Examiner, Dell Inc., NFC Wireless Charging Module, FCC ID: E2K-DWRFID2004 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of thi s module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip CTN730. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is CTN730. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested inside a specific platform. Please see section Photographs of Test Configuration in the test report, the EUT is for limited modular approval for this specific platform (model: DELL; Brand: T05J). 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: E2K-DWRFID2004 Report No.: RFXXXXXXXX 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Andrea Hsia Supervisor Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Reference No.: BDGE-WTW-P21120320_EXT Page No. 1 / 13 CONSTRUCTION PHOTOS OF EUT Brand：DELL ／ Model：DWRFID2004 Reference No.: BDGE-WTW-P21120320_EXT Page No. 2 / 13 End-product Portable Computer (Brand: DELL / Model: T05J) Reference No.: BDGE-WTW-P21120320_EXT Page No. 3 / 13 Reference No.: BDGE-WTW-P21120320_EXT Page No. 4 / 13 Antenna location Reference No.: BDGE-WTW-P21120320_EXT Page No. 5 / 13 Reference No.: BDGE-WTW-P21120320_EXT Page No. 6 / 13 Reference No.: BDGE-WTW-P21120320_EXT Page No. 7 / 13 Adapter (Brand: DELL / Model: DA45NM210) Reference No.: BDGE-WTW-P21120320_EXT Page No. 8 / 13 Adapter (Brand: DELL / Model: HA45NM210) Reference No.: BDGE-WTW-P21120320_EXT Page No. 9 / 13 Reference No.: BDGE-WTW-P21120320_EXT Page No. 10 / 13 Adapter (Brand: DELL / Model: LA45NM210) Reference No.: BDGE-WTW-P21120320_EXT Page No. 11 / 13 Reference No.: BDGE-WTW-P21120320_EXT Page No. 12 / 13 Reference No.: BDGE-WTW-P21120320_EXT Page No. 13 / 13 Touch pen (Brand: DELL / Model: PN9315A)

PPID label P/N: TBD PPID label SIZE: 9.5mm(0.375")W x 9.5mm(0.375")H 0.375” 0.375” SampleSample CPU Processor labels Label Location Plan for XPS Millennio WIFI XPS Millennio WIFI Sandy YangSandy Yang Samantha Tsai File releaseV0.12021/03/04 Update the contents of Laser Etching and system label ; Add XPS logo on A cover.V0.32021/03/26 Update the contents of system label ; Add e-logo.V0.42021/03/29 Update the contents of system label (Add JapanPC recyclemark).V0.52021/03/31 Ship to China XPS Millennio WIFI_Label Location Plan Update the contents of Laser Etching for WW.V0.62021/04/06 Update the contents of Laser Etching for WW and India.V0.72021/04/29 Removed China NAL label.V0.82021/05/10 Update the contents of system label ; Added dimensions of safety icon.V0.92021/05/17 Updated the service tag QR code of Laser Etching.V1.02021/05/25 Updated the contents of WW Laser Etching and contents of system label.V1.22021/06/08 V1.32021/06/15Updated the printing color of system label from Balck to Gray. V1.42021/06/30Update the contents of system label. V1.52021/07/08Updated the contents of system label and WW Laser Etching. V1.62021/07/09Updated the contents of Laser Etching for WW. V1.72021/07/22Updated the contents of Laser Etching for WW. V1.82021/08/03Updated the contents of system label (Draft 22 version). V2.02021/09/09Updated the contents of Laser Etching and system label for WW (Draft 26 version). V2.12021/09/10Added MCMC physical label (DPN: 1W6FJ) and ES label (DPN: 1CHTF) on A cover. V2.72022/01/07 Redefined the pasting location of CPU physical label on A cover. V2.82022/01/07 Redefined the pasting location of Windows label on A cover. V2.52021/10/18Updated the contents of Laser Etching and system label (Draft 28 version) V2.62021/12/22Updated the contents of system label for WW WIFI (Draft 29 version) 2021/10/06Removed the Energy star physical label ; Added the e-logo of Energy star. V2.3 2021/10/05 Updated the contents of Laser Etching and system label (Draft 27 version) Removed MCMC physical label (DPN: 1W6FJ) from A cover. System / Region / CPU Labels * This document is for reference only on label loca�on Please find the latest Label SKU/Image defini�on by Label Bom list e - logo SampleSample *All Images and label printed color of the label plan are just for reference only. Please follow database (BOM) for correct data. System Label - Wistron Factory (Online Prin�ng) 100mm x 20mm (R0.5x4) WW WIFI 4mm 5mm 7mm 8.128mm 6.3mm 5mm P/N: Y63GJ LBL,INTEL,CI5EVO,12,MICRO INTEL SKU: 348273-001 SIZE:14mm(0.551")W x 17.5mm(0.689")H 0.551” 0.689” P/N: 711GW LBL,INTEL,CI7EVO,12,MICRO INTEL SKU: 348276-001 SIZE:14mm(0.551")W x 17.5mm(0.689")H 0.551” 0.689” Updated the contents of Laser Etching and system label (Draft 30 version).V3.02022/02/09 Added PPID label ; Swap the Windows label and CPU label.V3.12022/02/14 Updated the contents of Laser Etching (0JJG2) and system label (6N2FV). [Draft 31 version]V3.22022/02/25 Updated the contents of Laser Etching (0JJG2). [Draft 32 version]V3.62022/03/14 2mm SampleSample 10mm 14.86 mm 5.96 mm 10.0 mm10.0 mm 10mm 4.5 mm 102.847 mm 2mm PPID label P/N: TBD PPID label SIZE: 9.5mm(0.375")W x 9.5mm(0.375")H 0.375” 0.375” SampleSample Ship to China (NAL) 40mm x 20mm Region Label Ship to DAO XPS Millennio 5G_Label Location Plan Label Location Plan for XPS Millennio 5G XPS Millennio 5G Sandy YangSandy Yang Samantha Tsai File releaseV0.12021/03/04 Update the contents of Laser Etching and system label.V0.32021/03/26 Update the contents of system label ; Add e-logo.V0.42021/03/29 Update the contents of system label (Add JapanPC recyclemark).V0.52021/03/31 Update the contents of Laser Etching for WW.V0.62021/04/06 Update the contents of Laser Etching for WW and India.V0.72021/04/29 Update the contents of system label ; Added dimensions of safety icon.V0.92021/05/17 Updated the service tag QR code of Laser Etching.V1.02021/05/25 Updated the contents of WW Laser Etching and contents of system label.V1.22021/06/08 V1.32021/06/15Updated the printing color of system label from Balck to Gray. V1.42021/06/30Update the contents of system label. V1.52021/07/08Updated the contents of system label and WW Laser Etching. V1.62021/07/09Updated the contents of Laser Etching for WW. V1.72021/07/22Updated the contents of Laser Etching for WW. V1.82021/08/03Updated the contents of system label (Draft 22 version). V2.02021/09/09Updated the contents of Laser Etching and system label for WW (Draft 26 version). System / Region / CPU Labels * This document is for reference only on label loca�on Please find the latest Label SKU/Image defini�on by Label Bom list V2.12021/09/10Added MCMC physical label (DPN: 1W6FJ) on A cover. V2.22021/09/10Added Energy star label (DPN: 1CHTF) on A cover. V2.42021/10/07Adjusted the sticking position of China NAL label to the right side corner. V2.3 2021/10/05 Updated the contents of Laser Etching and system label (Draft 27 version) Deleted MCMC physical label (DPN: 1W6FJ) from A cover. e - logo 2021/10/06Removed the Energy star physical label ; Added the e-logo of Energy star. System Label - Wistron Factory (Online Prin�ng) 100mm x 20mm (R0.5x4) WW 5G SampleSample 4mm 5mm 7mm 8.128mm 6.3mm 5mm *All Images and label printed color of the label plan are just for reference only. Please follow database (BOM) for correct data. V2.52021/10/18Updated the contents of Laser Etching and system label (Draft 28 version) V2.62021/12/22Updated the contents of system label for WW 5G (Draft 29 version) CPU Processor labels P/N: Y63GJ LBL,INTEL,CI5EVO,12,MICRO INTEL SKU: 348273-001 SIZE:14mm(0.551")W x 17.5mm(0.689")H 0.551” 0.689” P/N: 711GW LBL,INTEL,CI7EVO,12,MICRO INTEL SKU: 348276-001 SIZE:14mm(0.551")W x 17.5mm(0.689")H 0.551” 0.689” V2.72022/01/07 Redefined the pasting location of CPU physical label on A cover. V2.82022/01/07 Redefined the pasting location of Windows label on A cover. V3.02022/02/09Updated the contents of Laser Etching and system label (Draft 30 version). …

Text truncated - open the document above for the full version.

Label and label location Model: DWRFID2004 Label is sticked on the core side of cover. label

Reference No.: BDGE-WTW-P21120320_INT Page No. 1 / 17 CONSTRUCTION PHOTOS OF EUT Brand：DELL ／ Model：DWRFID2004 Reference No.: BDGE-WTW-P21120320_INT Page No. 2 / 17 End-product Portable Computer (Brand: DELL / Model: T05J) Reference No.: BDGE-WTW-P21120320_INT Page No. 3 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 4 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 5 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 6 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 7 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 8 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 9 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 10 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 11 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 12 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 13 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 14 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 15 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 16 / 17 Reference No.: BDGE-WTW-P21120320_INT Page No. 17 / 17

TEL : 886-3-327-3456 Page 1 of 19 FAX : 886-3-328-4978 Issued Date : Mar. 16, 2022 Template version: 211220 FCC SAR TEST REPORT Report No. : FA211211-02 FCC SAR TEST REPORT FCC ID : E2K-DWRFID2004 Equipment : NFC Wireless Charging Module Brand Name : DELL Model Name : DWRFID2004 Applicant : Dell Inc. One Dell Way Round Rock, TX 78682, USA Manufacturer : Dell Inc. One Dell Way Round Rock, TX 78682, USA Standard : FCC 47 CFR Part 2 (2.1093) The product was installed into Tablet (Brand Name DELL, Model Name: T05J) during test. The product was received on Jan. 05, 2022 and testing was started from Jan. 12, 2022 and completed on Jan. 12, 2022. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample provide by manufacturer and the test data has been evaluated in accordance with the test procedures given in 47 CFR Part 2.1093 and FCC KDB and has been pass the FCC requirement. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Laboratory, the test report shall not be reproduced except in full. Sporton International Inc. EMC & Wireless Communications Laboratory No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page 2 of 19 FAX : 886-3-328-4978 Issued Date : Mar. 16, 2022 Template version: 211220 FCC SAR TEST REPORT Report No. : FA211211-02 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Guidance Applied .......................................................................................................................................................... 4 3. Equipment Under Test (EUT) Information ................................................................................................................... 5 3.1 General Information ............................................................................................................................................... 5 4. RF Exposure Limits....................................................................................................................................................... 6 4.1 Uncontrolled Environment ...................................................................................................................................... 6 4.2 Controlled Environment .......................................................................................................................................... 6 5. Specific Absorption Rate (SAR) ................................................................................................................................... 7 5.1 Introduction ............................................................................................................................................................ 7 5.2 SAR Definition ........................................................................................................................................................ 7 6. System Description and Setup .................................................................................................................................... 8 6.1 Test Site Location ................................................................................................................................................... 8 6.2 E-Field Probe ......................................................................................................................................................... 9 6.3 Data Acquisition Electronics (DAE) ........................................................................................................................ 9 6.4 Phantom ................................................................................................................................................................10 6.5 Device Holder........................................................................................................................................................ 11 7. Measurement Procedures ...........................................................................................................................................12 7.1 Spatial Peak SAR Evaluation ................................................................................................................................12 7.2 Power Reference Measurement............................................................................................................................13 7.3 Area Scan .............................................................................................................................................................13 7.4 Zoom Scan ............................................................................................................................................................14 7.5 Volume Scan Procedures .............................…

Text truncated - open the document above for the full version.