E2K-DWRFID2301RFID 13.56MHz Wireless Module

Latitude 7350 Detachable T07H/T07H001 Latitude 7350 Detachable (T07H)

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a C lass B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution:  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. * Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Prohibited for control of or communications with unmanned aircraft systems, including drones. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. Industry Canada statement  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.  This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios.  Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées. Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.

OEM Installation Guidance For Dell RFID 13.56MHz Wireless Module, FCC ID: E2K-DWRFID2301, IC : 1514B-DWRFID2301 ‐ OEM integrators must ensure that its product is electrically identical to Dell’s reference designs. Any modifications to Dell’s reference designs may invalidate regulatory approvals in relation to the product, or may necessitate notifications to the relevant regulatory authorities. ‐ OEM integrators are responsible for regression testing to accommodate changes to designs, new antennas, and host and submit for C2PC filings. Colocation with other transmitter modules will be addressed through filings for those co‐located transmitters when necessary or that colocation of other transmitters will be according to applicable KDB guidelines including those for RF exposure ‐The final system integrator must ensure there is no instruction provided in the user manual or customer documentation indicating how to install or remove the transmitter ‐ Appropriate labels must be affixed to the product that complies with applicable regulations in all respects. The regulatory label on the final system must include the statement: “Contains FCC ID: E2K-DWRFID2301 and/or IC: 1514B-DWRFID2301”. ‐ A user’s manual or instruction manual must be included with the product that contains the text as required by applicable law shall be provided to OEM integrators. They may include: 1. USA—Federal Communications Commission (FCC) FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: ‐Reorient or relocate the receiving antenna ‐Increase the distance between the equipment and the receiver. ‐Connect the equipment to outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The final host manual shall include the following regulatory statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: ‐Reorient or relocate the receiving antenna ‐Increase the distance between the equipment and the receiver. ‐Connect the equipment to outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Canada ‐ Industry Canada (IC) This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French: Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L‘utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Radiation Exposure Statement: The product comply with the FCC/IC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonc…

Text truncated - open the document above for the full version.

Dell Customer Communication – Confidential DELL INC. One Dell Way Round Rock, Texas 78682 United States Date: 2023-10-27 FCC ID: E2K-DWRFID2301 AUTHORIZATION LETTER To Whom It May Concern: Dell Inc. hereby authorizes Amanda Wu / Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu / Senior Specialist of BV CPS Taoyuan on Dell Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, --------------------------------------------------------- William Wei / Regulatory Compliance Engineer Dell Inc. Tel: 886 2 2376-6556 E-mail: [email protected]

Dell Inc. Don Bobo MS: PS4-30 Distingished Member of Technical Staff One Dell Way EMC, Global Regulations and Standards Round Rock, Texas 78682 Telephone 512.593.8560 www.dell.com e-mail [email protected] Worldwide Regulatory Compliance Engineering & Environmental Affairs Internal Use - Confidential Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 January 9, 2023 FCC authorization letter for Dell Regulatory employees To whom it may concern, I, the undersigned, as the authorized signatory for the Dell Inc. grantee code E2K, hereby authorize the following EMC & Wireless Regulatory Engineers of Dell Inc., to act on my behalf in all manners relating to processes required according to FCC rules for equipment authorization: This authorization shall be sent along with application when filing with the FCC Certification Division and is valid until further written notice from the applicant. If you have any questions or need additional information, please feel free to contact me at 512-593-8560 or 512-619-7976. Sincerely, Don Bobo, Dell Inc., FRN: 0008359580 Bill Wang April Chang Fiona Y Chen Kay Chen Yan Papernov Jessie Goh Jack TS Huang Tommy Hwang Nai Ghee Koh Jason KP Lee Jason Limoges Leonel Lopez James V Nguyen Rex Wan William Wei Steve L Williams Julie Shen Leo Hong Dyllan Chang Ken Tai CY Chang Jessie Lin Greg Hsiao Chloe Lin Brad Chen

Dell Customer Communication – Confidential DELL INC. One Dell Way Round Rock, Texas 78682 United States Date: 2023-10-27 FCC ID: E2K-DWRFID2301 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, --------------------------------------------------------- William Wei / Regulatory Compliance Engineer Dell Inc. Tel: 886 2 2376-6556 E-mail: [email protected]

Dell Customer Communication – Confidential DELL INC. One Dell Way Round Rock, Texas 78682 United States Date: 2024-03-19 FCC ID: E2K-DWRFID2301 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 2024/04/04 in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Internal Photos Test Set Up Photos User’s manual Sincerely yours, --------------------------------------------------------- William Wei / Regulatory Compliance Engineer Dell Inc. Tel: 886 2 2376-6556 E-mail: [email protected]

FCC ID: E2K-DWRFID2301 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch November 27, 2023 Dear Application Examiner, Dell Inc., RFID 13.56MHz Wireless Module, FCC ID: E2K-DWRFID2301 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has not been shielded. The EUT is for limited modular approval for this specific platform (Brand: DELL; Model: T07H). 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip BCM58202. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is BCM58202. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested inside a specific platform. Please see section Photographs of Test Configuration in the test report, the EUT is for limited modular approval for this specific platform (Brand: DELL; Model: T07H). 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, ___________________________ Amanda Wu / Senior Specialist Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch No. 70, Wenming Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.), 333011 Tel: +886-3-264-1929 Email: [email protected]

Reference No.: BEDW-WTW-P23070680 _EXT Page No. 1/ 25 CONSTRUCTION PHOTOS OF EUT Brand：DELL ／ Model：DWRFID2301 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 2/ 25 End-product Portable Computer-Tablet (Brand: DELL / Model: T07H) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 3/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 4/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 5/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 6/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 7/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 8/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 9/ 25 Touch pen (Brand: DELL / Model: PN7350A) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 10/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 11/ 25 Keypad (Brand: DELL / Model: M23LSPC-BT) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 12/ 25 Adapter 1 (Brand: DELL / Model: AA65NM220) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 13/ 25 Adapter 2 (Brand: DELL / Model: DA60NM200) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 14/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 15/ 25 Adapter 3 (Brand: DELL / Model: HA60NM200) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 16/ 25 Adapter 4 (Brand: DELL / Model: HA65NM190) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 17/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 18/ 25 Adapter 5 (Brand: DELL / Model: DA65NM190) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 19/ 25 Adapter 6 (Brand: DELL / Model: LA65NM190) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 20/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 21/ 25 Adapter 7 (Brand: DELL / Model: HKA65NM200) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 22/ 25 Adapter 8 (Brand: DELL / Model: LA60NM200) Reference No.: BEDW-WTW-P23070680 _EXT Page No. 23/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 24/ 25 Reference No.: BEDW-WTW-P23070680 _EXT Page No. 25/ 25 AC power cord (0.85m)

DWRFID2301 Label Drawing RFID Module RFID Antenna Label

DWRFID2301 Contains FCC ID: E2K-DWRFID2301 Contains IC: 1514B-DWRFID2301 Host: T07H

Reference No.: BEDW-WTW-P23070680 _INT Page No. 1/ 7 CONSTRUCTION PHOTOS OF EUT Brand：DELL ／ Model：DWRFID2301 Reference No.: BEDW-WTW-P23070680 _INT Page No. 2/ 7 End-product Portable Computer-Tablet (Brand: DELL / Model: T07H) Reference No.: BEDW-WTW-P23070680 _INT Page No. 3/ 7 Antenna Antenna Reference No.: BEDW-WTW-P23070680 _INT Page No. 4/ 7 Reference No.: BEDW-WTW-P23070680 _INT Page No. 5/ 7 Reference No.: BEDW-WTW-P23070680 _INT Page No. 6/ 7 Battery 1 (Brand: DELL / Model: N8K40) (Manufacturer: BYD) Battery 2 (Brand: DELL / Model: N8K40) (Manufacturer: Simplo) Reference No.: BEDW-WTW-P23070680 _INT Page No. 7/ 7

Report No.: MFBEDW-WTW-P23070680 Page No. 1/ 6Report Format Version: 6.1.1 RF Exposure Report Report No.:MFBEDW-WTW-P23070680 FCC ID:E2K-DWRFID2301 Test Model:DWRFID2301 Received Date:Aug. 10, 2023 Test Date:Nov. 11, 2023 Issued Date:Nov. 23, 2023 Applicant:Dell Inc. Address:One Dell Way, Round Rock, Texas 78682, USA Issued By:Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address:No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location:No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Desi gnation Number:788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBEDW-WTW-P23070680 Page No. 2/ 6Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 3 SAR Test Exclusion Thresholds .......................................................................................................... 6 4 Conclusion ............................................................................................................................................ 6 Report No.: MFBEDW-WTW-P23070680 Page No. 3/ 6Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued MFBEDW-WTW-P23070680 Original release Nov. 23, 2023 Report No.: MFBEDW-WTW-P23070680 Page No. 4/ 6Report Format Version: 6.1.1 1 Certificate of Conformity Product: RFID 13.56MHz Wireless Module Brand: DELL Test Model: DWRFID2301 Sample Status: Engineering sample Applicant: Dell Inc. Test Date: Nov. 11, 2023 FCC Rule Part: FCC Part 2 (Section 2.1091) Standards: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Nov. 23, 2023 Pettie Chen / Senior Specialist Approved by : , Date:Nov. 23, 2023 Jeremy Lin / Project Engineer Report No.: MFBEDW-WTW-P23070680 Page No. 5/ 6Report Format Version: 6.1.1 2 RF Exposure Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ꞏ[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison. The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)ꞏ( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)ꞏ10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test …

Text truncated - open the document above for the full version.

Report No.: RFBEDW-WTW-P23070680 Page No. 1/ 32Report Format Version: 6.1.1 FCC Test Report Report No.:RFBEDW-WTW-P23070680 FCC ID:E2K-DWRFID2301 Test Model:DWRFID2301 Received Date:Aug. 10, 2023 Test Date:Nov. 11, 2023 Issued Date:Nov. 23, 2023 Applicant:Dell Inc. Address:One Dell Way, Round Rock, Texas 78682, USA Issued By:Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address:No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1):No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan Test Location (2):No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) FCC Registration / Desi gnation Number: 788550 / TW0003 281270 / TW0032 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBEDW-WTW-P23070680 Page No. 2/ 32Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ..............................................…

Text truncated - open the document above for the full version.