E2KJ42AWTABLET COMPUTER

FCC Radiation Exposure Statement WARNING: The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, this device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has been evaluated for and shown compliant with the FCC RF Exposure limits under mobile exposure conditions (antennas are greater than 20cm from a person’s body). This device has also been evaluated for and shown compliant with the FCC RF exposure limits under portable exposure conditions (antennas are within 20 cm of a person's body) when installed in certain specific configurations. Details of the authorized configurations can be found at https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID number on the device. Interference Statement This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Notice: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:  Reorient the receiving antenna.  Relocate the system with respect to the receiver.  Move the system away from the receiver.  Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of Dell Inc. or an experienced radio/television technician for additional suggestions. NOTE: This Dell Mobile Broadband device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment.

Electromagnetic Interference (EMI) is any signal or emission, radiated in free space or conducted along power or signal leads, that endangers the functioning of radio navigation or other safety service or seriously degrades, obstructs, or repeatedly interrupts a licensed radio communications service. Radio communications services include but are not limited to AM/FM commercial broadcast, television, cellular services, radar, air-traffic control, pager, and Personal Communication Services (PCS). These licensed radio services, and unlicensed radio services, such as WLAN or Bluetooth, along with unintentional radiators such as digital devices, including computer systems, contribute to the electromagnetic environment. Electromagnetic Compatibility (EMC) is the ability of items of electronic equipment to function properly together in the electronic environment. While this computer system has been designed and determined to be compliant with regulatory agency limits for EMI, there is no guarantee that interference will not occur in a particular installation. Dell™ products are designed, tested, and classified for their intended electromagnetic environment. These electromagnetic environment classifications generally refer to the following harmonized definitions: • Class B products are intended for use in residential/domestic environments but may also be used in non-residential/non-domestic environments. Note: The residential/domestic environment is an environment where the use of broadcast radio and television receivers may be expected within a distance of 10 m from where this product is used. • Class A products are intended for use in non-residential/non-domestic environments. Class A products may also be utilized in residential/domestic environments but may cause interference and require the user to take adequate corrective measures. If this equipment does cause interference with radio communications services, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: • Reorient the receiving antenna. • Relocate the computer with respect to the receiver. • Move the computer away from the receiver. • Plug the computer into a different outlet so that the computer and the receiver are on different branch circuits. If necessary, consult a Dell Technical Support representative or an experienced radio/television or EMC technician for additional suggestions. Information Technology Equipment (ITE), including peripherals, expansion cards, printers, input/output (I/O) devices, monitors, and so on, that are integrated into or connected to the system should match the electromagnetic environment classification of the computer system. A Notice about Shielded Signal Cables: Use only shielded cables for connecting peripherals to any Dell™ device to reduce the possibility of interference with radio communications services. Using shielded cables ensures that you maintain the appropriate EMC classification for the intended environment. For parallel printers, a cable is available from Dell™. If you prefer, you can order a cable from Dell™ on the World Wide Web at www.dell.com . FCC, Class B This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. Notice: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the antenna of the radio/television receiver. • Increase the separation between this equipment and the radio/television receiver. • Plug the equipment into a different outlet so that the equipment and the radio/television receiver are on different power mains branch circuits. • Consult a representative of Dell™ or an experienced radio/television technician for additional suggestions. The following information is provided on the device or devices covered in this document in compliance with FCC regulations: Product name: Please refer to the product-specific Product Safety, EMC and Environmental Datasheet for the Regulatory Model and Reference Number identification of products covered by an FCC Declaration of Conformity. This equipment’s unique regulatory compliance identification is provided by the Regulatory Model and Reference Number. These regulatory compliance identification markings are on the regulatory label affixed to your equipment and should not be confused with marketing name or model of the equipment. To facilitate positive identification, request for regulatory compliance information for this equipment should include the Regulatory Model and Reference Number. Company name: Dell Inc. is the responsible party or acting as a point-of-contact for the responsible party of a Dell-branded ODM/OEM product. For an EMC compliance issue or a regulatory inquiry, please use the following contact information: Dell Inc. Worldwide Regulatory Compliance, Engineering and Environmental Affairs One Dell Way PS4-30 Round Rock, Texas 78682 USA 512-338-4400 For a copy of the FCC Declaration of Conformity, please send an e-mail to [email protected] providing the Marketing Name, Regulatory Model and Reference Number for the applicable product(s) as listed on the…

Text truncated - open the document above for the full version.

Quick Start Guide Translated Text Here | Translated Text Here Translated Text Here | Translated Text Here 10 About Your Tablet About Your Tablet | About Your Tablet About Your Tablet | About Your Tablet 1. Power button 2. MicroSD and micro-SIM card slot 3. Front camera 4. Camera-status light 5. Ambient-light sensor 6. Headphone port 7. Volume buttons (2) 8. Windows button 9. Rear microphone 10. Rear camera 11. Speaker 12. Docking-latch slot 13. Power-adapter/ docking port 14. Micro-USB port 15. Docking-latch slot 16. Speaker 17. Battery-charging light 18. Front microphones (2) 1. Power button 2. MicroSD and micro-SIM card slot 3. Front camera 4. Camera-status light 5. Ambient-light sensor 6. Headphone port 7. Volume buttons (2) 8. Windows button 9. Rear microphone 10. Rear camera 11. Speaker 12. Docking-latch slot 13. Power-adapter/ docking port 14. Micro-USB port 15. Docking-latch slot 16. Speaker 17. Battery-charging light 18. Front microphones (2) 6 7 8 3 2 1 5 4 109 Before Sending Your Tablet for Repair Dell may reset your tablet to factory settings to resolve the issue with your tablet. Back up your data before sending your tablet for repair. Before Sending Your Tablet for Repair Dell may reset your tablet to factory settings to resolve the issue with your tablet. Back up your data before sending your tablet for repair. Before Sending Your Tablet for Repair Dell may reset your tablet to factory settings to resolve the issue with your tablet. Back up your data before sending your tablet for repair. Before Sending Your Tablet for Repair Dell may reset your tablet to factory settings to resolve the issue with your tablet. Back up your data before sending your tablet for repair. Before Sending Your Tablet for Repair Dell may reset your tablet to factory settings to resolve the issue with your tablet. Back up your data before sending your tablet for repair. More Information For more information on your tablet, see the User’s Manual available on your tablet or support.dell.com/manuals. More Information For more information on your tablet, see the User’s Manual available on your tablet or support.dell.com/manuals. More Information For more information on your tablet, see the User’s Manual available on your tablet or support.dell.com/manuals. More Information For more information on your tablet, see the User’s Manual available on your tablet or support.dell.com/manuals. More Information For more information on your tablet, see the User’s Manual available on your tablet or support.dell.com/manuals. © 2013 Dell Inc. Dell™, the DELL logo, and XPS™ are trademarks of Dell Inc. © 2013 Dell Inc. Dell™, the DELL logo, and XPS™ are trademarks of Dell Inc. © 2013 Dell Inc. Dell™, the DELL logo, and XPS™ are trademarks of Dell Inc. © 2013 Dell Inc. Dell™, the DELL logo, and XPS™ are trademarks of Dell Inc. © 2013 Dell Inc. Dell™, the DELL logo, and XPS™ are trademarks of Dell Inc. 1. Power button 2. MicroSD and micro-SIM card slot 3. Front camera 4. Camera-status light 5. Ambient-light sensor 6. Headphone port 7. Volume buttons (2) 8. Windows button 9. Rear microphone 10. Rear camera 11. Speaker 12. Docking-latch slot 13. Power-adapter/ docking port 14. Micro-USB port 15. Docking-latch slot 16. Speaker 17. Battery-charging light 18. Front microphones (2) 1. Power button 2. MicroSD and micro-SIM card slot 3. Front camera 4. Camera-status light 5. Ambient-light sensor 6. Headphone port 7. Volume buttons (2) 8. Windows button 9. Rear microphone 10. Rear camera 11. Speaker 12. Docking-latch slot 13. Power-adapter/ docking port 14. Micro-USB port 15. Docking-latch slot 16. Speaker 17. Battery-charging light 18. Front microphones (2) 1. Power button 2. MicroSD and micro-SIM card slot 3. Front camera 4. Camera-status light 5. Ambient-light sensor 6. Headphone port 7. Volume buttons (2) 8. Windows button 9. Rear microphone 10. Rear camera 11. Speaker 12. Docking-latch slot 13. Power-adapter/ docking port 14. Micro-USB port 15. Docking-latch slot 16. Speaker 17. Battery-charging light 18. Front microphones (2) 13 12 11 17 18 14 15 16 Printed in China2013 - 03 Setting Up Your Tablet Insert the microSD (optional) and micro-SIM card Insert the microSD (optional) and micro-SIM card | Insert the microSD (optional) and micro-SIM card Insert the microSD (optional) and micro-SIM card | Insert the microSD (optional) and micro-SIM card Charge the battery (at least 4 hours) Charge the battery (at least 4 hours) Charge the battery (at least 4 hours) Charge the battery (at least 4 hours) Charge the battery (at least 4 hours) Press and hold the power button to turn on the tablet Press and hold the power button to turn on the tablet Press and hold the power button to turn on the tablet Press and hold the power button to turn on the tablet Press and hold the power button to turn on the tablet Setting Up Your Tablet | Setting Up Your Tablet Setting Up Your Tablet | Setting Up Your Tablet Locate the Service Tag Locate the Service Tag Locate the Service Tag Locate the Service Tag Locate the Service Tag Windows 8 Swipe to access more tiles Swipe to access more tiles Swipe to access more tiles Swipe to access more tiles Swipe to access more tiles TilesTiles | Tiles | Tiles | Tiles Charms sidebar Swipe from right edge of the display Swipe from right edge of the display Swipe from right edge of the display Swipe from right edge of the display Swipe from right edge of the display Charms sidebar | Charms sidebar Charms sidebar | Charms sidebar Getting started Getting started Getting started Getting started Getting started My Dell Support Center My Dell Support Center My Dell Support Center My Dell Support Center My Dell Support Center ResourcesResources | Resources | Resources | Resources 1 2 3

February 14, 2013 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 RE: Application for Certification FCC ID: E2KJ42AW Dear Sir/Madam: Sierra Wireless, Inc. is submitting an application for the certification of a Dell Tablet Computer (hereafter referred to as “the Tablet”) under FCC ID: E2KJ42AW on behalf of Dell, Inc. The Tablet embeds WiFi, Bluetooth and WWAN radio transmitters. Before embedding the WWAN radio transmitter, the Tablet with embedded WiFi and Bluetooth radio transmitters has already been certified by the Commission under FCC ID: E2KJ42A. The WWAN radio transmitter has been granted modular approval by the Commission under FCC ID: N7NEM7700. There are no changes to the WiFi and Bluetooth radio transmitters and their respective antennas when the WWAN radio transmitter is integrated to the Tablet. Each of the three radio transmitters embedded in the Tablet has its own antenna. This application includes exhibits previously filed under FCC ID: E2KJ42A and FCC ID: N7NEM7700 as these exhibits are applicable to the current application. Please contact me if you have any questions or need further information regarding this application. Sincerely, Ying Wang Manager, Regulatory Compliance

January 30, 2013 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for FCC ID: E2KJ42AW We hereby request that the exhibits listed below, submitted with our application for certification, be withheld from public disclosure. This request is made under the provisions of Section 0.457(d) and 0.459 of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act.  Schematics  Block Diagram  Operation Description  Tune Up Procedure We also request Long-Term Confidentiality for the internal photos, citing 726920 D02 Confidentiality Procedures Detail v02 “Internal photos of a consumer device may be held confidential when the circuit board is enclosed in epoxy or in a material that would destroy the circuit board if removed, or if the device is sealed and disassembly would destroy the product; “ Furthermore, pursuant to Public Notice DA 04-1705 in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, we request the following exhibits be withheld from public viewing for a short limited time of 180 days from the date of the Grant of Equipment Authorization, due to the sensitive business information:  User Guide  External Photos  Test Setup Photos Best Regards Ying Wang Manager, Regulatory Compliance

Dell Inc. Thanh K. Nguyen MS: PS4-30 EMC, Global Regulations and Standards One Dell Way Telephone 512 723 8862 Round Rock, Texas 78682 Telefax 512.283.9268 www.dell.com e-mail [email protected] Worldwide Regulatory Compliance Engineering & Environmental Affairs January 23, 2013 To: Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Copy: Sierra Wireless Ying Wang, Regulatory Compliance Manager 13811 Wireless Way Richmond, BC Canada V6V 3A4 FCC Agent Authorization To whom it may concern, I, the undersigned, hereby authorize Ying Wang, Regulatory Compliance Manager of Sierra Wireless to act on our behalf as our agent in all manners relating to application for equipment authorization on FCC ID E2KJ42AW, including signing of all documents relating to these matters. Any and all acts carried out by Ying Wang, Regulatory Compliance Manager of Sierra Wireless on our behalf shall have the same effect as acts of our own. In authorizing this agent, we still recognize that we the FCC Grantee are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Agent; 2 e) use certification only to indicate the products are certified as being in conformity with specified standards; f) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; g) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the agent, TCB and FCC regulations; h) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the agent when requested; i) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification and document the actions taken. This authorization shall be sent along with application when filing with the FCC Certification Division and is valid until further written notice from the applicant. If you have any questions or need additional information, please feel free to contact this letter signatory using the contact information at the top of the first page or you may contact the Dell Grantee at 512-728-1081 or [email protected]. Sincerely, Thanh K. Nguyen 512 723 8862 [email protected] Dell Inc. FRN: 0008359580

Dell Inc. Richard Worley, NCE MS: PS4-30 EMC, Global Regulations and Standards One Dell Way Telephone 512.728.1081 Round Rock, Texas 78682 Telefax 512.283.9268 www.dell.com e-mail [email protected] Worldwide Regulatory Compliance Engineering & Environmental Affairs October 28, 2012 Federal Communication Commission Office of Engineering and Technology Equipment Authorization and Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Anti-Drug Abuse Attestation Gentlemen: Please accept this letter as an attestation on behalf of Dell Inc. that to the best of our knowledge, information and belief, no party to this application, as defined in 47 CFR 1.2002(b), including our officers, directors, or persons holding 5% or more of outstanding stock or shares, voting or non- voting, have been denied federal benefits, including FCC benefits, under Section 5301 of the Anti-Drug Abuse Act of 1998.21 U.S.C. 862. This attestation shall be sent along with application when filing with the FCC Certification Division and is valid until further written notice from the applicant. If you have any questions or need additional information, please feel free to contact me at 512- 728-1081 or 512-431-1084. Sincerely, Richard Worley Dell Inc. FRN: 0008359580

Dell Inc. Richard Worley, NCE MS: PS4-30 EMC, Global Regulations and Standards One Dell Way Telephone 512.728.1081 Round Rock, Texas 78682 Telefax 512.283.9268 www.dell.com e-mail [email protected] Worldwide Regulatory Compliance Engineering & Environmental Affairs Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 January 23, 2013 FCC authorization letter for Dell Regulatory employees To whom it may concern, I, the undersigned, as the authorized signatory for the Dell Inc. grantee code E2K, hereby authorize the following EMC & Wireless Regulatory Engineers of Dell Inc., to act on my behalf as our agent in all manners relating to processes required according to FCC rules for equipment authorization: Thanh Nguyen Chase Berry Fiona Y Chen Hank Liu Don Bobo Steve L Williams Rick Linford James Carrillo Benton S Ng Alden Neilson This authorization shall be sent along with application when filing with the FCC Certification Division and is valid until further written notice from the applicant. If you have any questions or need additional information, please feel free to contact me at 512-728-1081 or 512-431-1084. Sincerely, Richard Worley Dell Inc. FRN: 0008359580

Photographs of EUT Report No.: EP311130 Brand Name: Dell / Model Name: J42A SPORTON INTERNATIONAL INC. Page Number : 1 of 31 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW 720510 1. External Photograph of EUT Photographs of EUT Report No.: EP311130 Brand Name: Dell / Model Name: J42A SPORTON INTERNATIONAL INC. Page Number : 2 of 31 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW Photographs of EUT Report No.: EP311130 Brand Name: Dell / Model Name: J42A SPORTON INTERNATIONAL INC. Page Number : 3 of 31 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW List of Accessory: Specification of Accessory AC Adapter Brand Name Dell Model Name AA30NM131 Battery Brand Name Dell Model Name JD33K WWAN Module Brand Name AirPrime Model Name EM7700 WLAN & Bluetooth chip Brand Name Qualcomm Model Name WCN3660 Remark: For accessories equipped with this EUT, please refer to the following photos. 2. Photograph of Accessory Photographs of EUT Report No.: EP311130 Brand Name: Dell / Model Name: J42A SPORTON INTERNATIONAL INC. Page Number : 4 of 31 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW Photographs of EUT Report No.: EP311130 Brand Name: Dell / Model Name: J42A SPORTON INTERNATIONAL INC. Page Number : 5 of 31 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW AC Adapter Photographs of EUT Report No.: EP311130 Brand Name: Dell / Model Name: J42A SPORTON INTERNATIONAL INC. Page Number : 6 of 31 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW Battery

Regulatory label

SPORTON INTERNATIONAL INC. Page Number : 1 of 73 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW FCC SAR Test Report Report No. : FA311130 FCC SAR Test Report APPLICANT : DELL EQUIPMENT : Tablet PC BRAND NAME : Dell MODEL NAME : J42A FCC ID : E2KJ42AW STANDARD : FCC 47 CFR Part 2 (2.1093) ANSI/IEEE C95.1-1992 IEEE 1528-2003 FCC OET Bulletin 65 Supplement C (Edition 01-01) The product was completely tested on Jan. 18, 2013. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the procedures and shown the compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. SPORTON INTERNATIONAL INC. Page Number : 2 of 73 TEL : 886-3-327-3456 Report Issued Date : Jan. 24, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : E2KJ42AW FCC SAR Test Report Report No. : FA311130 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Administration Data ...................................................................................................................................................... 5 2.1 Testing Laboratory .................................................................................................................................................. 5 2.2 Applicant ................................................................................................................................................................ 5 2.3 Manufacturer .......................................................................................................................................................... 5 2.4 Application Details .................................................................................................................................................. 5 3. General Information ...................................................................................................................................................... 6 3.1 Description of Equipment Under Test (EUT) .......................................................................................................... 6 3.2 Maximum RF output power among production units .............................................................................................. 7 3.3 Product Photos......................................................................................................................................................10 3.4 Applied Standard ...................................................................................................................................................10 3.5 Device Category and SAR Limits ..........................................................................................................................10 3.6 Test Conditions ......................................................................................................................................................10 4. Specific Absorption Rate (SAR) ..................................................................................................................................13 4.1 Introduction ...........................................................................................................................................................13 4.2 SAR Definition .......................................................................................................................................................13 5. SAR Measurement System ..........................................................................................................................................14 5.1 E-Field Probe ........................................................................................................................................................15 5.2 Data Acquisition Electronics (DAE) .......................................................................................................................16 5.4 Robot ....................................................................................................................................................................17 5.5 Measurement Server .............................................................................................................................................17 5.6 Phantom ................................................................................................................................................................18 5.7 Device Holder........................................................................................................................................................19 5.8…

Text truncated - open the document above for the full version.