E2XBTEP45C2GABluetooth Module

1 - USER MANUAL - Contents 1. Overview 2. Major Features 3. External 4. Module Block & Interfaces 5. Demension 6. FCC & Industry Canada Regulatory Compliance 1. Overview This specification covers Bluetoot h module(class-2), which complies with Bluetooth specification version 2.0 and integrates RF, Baseband, and Flash in a small package. This module has deployed CSR's BC04 External (BC417143B) chipset. 2. Major Features -, Bluetooth Spec. v2.0 Complaint -, Class 2 Level Output Power Available (Max. 4dBm) -, Full Speed Bluetooth operation with Piconet and Scatternet support -, Support of Low power modes: Park, Sniff and Hold -, 8 Mbit of Flash -, UART, USB, SPI Interface Available 3. External Appearance 1) Marking should be in clear and distinguishable characters. - No dim, spread, cut and erased marking. 2) Appearance should be managed as specified below: - No press (depth 0.1mm, length 5mm under). - No different substance, corros ion, distortion, discoloration etc. - Maintenance of the original condition (Case's edge, binding between cover and chassis). - Size must be as drawn in physical dimension diagram. 4. Module Block & Interfaces 5. Dimension The dimension is 14.6mm x 14.0mm x 2.2mm(Typ.) 6. FCC & Industry Canada Regulatory Compliance FCC & Industry Canada Regulatory Compliance This device complies with Part 15 of t he FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Your mobile device is a low power radio transmitter and receiver. When it is ON, it receives and also sends out r adio frequency (RF) signals. In August 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for mobile devices. Those guidelines are consistent with safety standards previously set by both U.S. and international standards bodies: American National Standard Institute (ANSI), National Council of Radiation Protection and Measurements(NCRP), and Internat ional Commission on Non-Ionizing Radiation Protection (ICNRP). Those standards were based on comprehensive and periodic evaluations of the relevant scientific literature. The design of your phone complies with the FCC guidelines and applicable. Statement according to FCC part 15.105 NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no g uarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Statement according to FCC part 15.21 Modifications not expressly approved by this company could void the user's authority to operate the equipment. RF exposure FCC This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

SAMSUNG ELECTRO-MECHANICS CO.,LTD. 314,Maetan 3-Dong Yeongtong-Gu, Suwon, Gyunggi-Do, 442-743,South Korea Tel: +82 31 2106902 Fax: +82 31 3007900G †††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† G Specification SheetG Object Dipol Antenna REV.IRGPage 1/6 Model name ACE-2450R Date 2007-01-23 System BTEP45C2GA Written Jong-Min Kim Electric Specification Frequency 2.4GHz – 2.5GHz Radiation Pattern Omni Directional V.S.W.RG 1.5 : 1 (Max) Gain (max) 2 dBi Input Impedance 50 (ȳ) Polarization Vertical Power Handling Max. 3 Watts Mechanical Specification Dimensions 124.0 mm r 2.0 mm Weight 12 g r 1g Radiator Material Copper Operation Temperature -30 ~ 60 qC Operation Humidity 0 - 95 % Option SMA Male Type, 0 ~ 90 q Tilt Antenna The rest G

SAMSUNG ELECTRO-MECHANICS CO.,LTD. 314,Maetan 3-Dong Yeongtong-Gu, Suwon, Gyunggi-Do, 442-743,South Korea Tel: +82 31 2106902 Fax: +82 31 3007900 ______________________________________________________________________ LETTER OF AUTHORIZATION DATE : Jan. 03, 2007 To whom it may concern: We the undersigned, hereby authorize ETS Germany to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by ETS Germany on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from SAMSUNG ELECTRO-MECHANICS CO.,LTD .. Sincerely, (Company counsel or company officer signature) Name : Mr J. M. Kim Title : Assistant Engineer (Name and Title)

SAMSUNG ELECTRO-MECHANICS CO.,LTD. 314,Maetan 3-Dong Yeongtong-Gu, Suwon, Gyunggi-Do, 442-743,South Korea Tel: +82 31 2106902 Fax: +82 31 3007900 ______________________________________________________________________ Date : 2007. 01 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Request for Confidentiality SAMSUNG ELECTRO-MECHANICS CO.,LTD . FCC ID: E2XBTEP45C2GA Gentlemen, In accordance with 0.459 of CFR 47, SAMSUNG ELECTRO-MECHANICS CO.,LTD .hereby requests confidentiality of all Schematics, Parts List, Operating Description attachments for the subject application. These documents contain detailed system and equipment description and related information about the product which SAMSUNG ELECTRO-MECHANICS CO.,LTD .considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, SAMSUNG ELECTRO-MECHANICS CO.,LTD . considers that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Name : J. M. Kim Title : Assistant Engineer Company : SAMSUNG ELECTRO-MECHANICS CO.,LTD .

The Samsung Electro-Mechanics Co., Bluetooth module BTEP45C2GA is seeking FCC authorization as a modular transmitter. The requirements of the FCC Public notice DA00-1407 are met. The following requirements are fulfilled: 1. The modular transmitter must have its own RF shielding The radio portion of the module is contained in its own RF shielding. See enclosed product photos in exhibit “external Photos”. 2. The modular transmitter must have buffered modulation/data inputs The module has a memory management unit inside of the IC and external. It buffers the data inputs from UART and USB terminal. 3. The modular transmitter must have its own power supply regulation The IC contains an own voltage regulation. In case of changes in the supply voltage VCC (for example caused by temperature changes or other effects), the internal voltage will be stabilized. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204c The unit is intended for use with listed antenna type as noted in the test report. or with an antenna that has less antenna gain. Requirements for the use of external antennas are specified in Exhibit Declaration about antenna configurations BTEP45C2GA. The modular transmitter was tested in a stand-alone configuration. The module was fixed in the Development Kit during the test. See also test setup photos in test report (Exhibit Test Report FCC Part 15.247). 6. The modular transmitter must be labelled with its own FCC ID number The EUT will be labelled with its own FCC ID number. The label is specified in Exhibit “Label Sample/Loc”. If the module is installed inside of an end-product, the label will not be visible. In this case the OEM customer will be instructed to how to apply the exterior label. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The EUT is compliant with all applicable FCC rules. Detail instructions are given in the product Users Guide 8. The modular transmitter must comply with any applicable RF exposure requirements. The device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This OEM module is approved for use in products operating as mobile and portable transmitting device with respect to 2.1091 and 2.1093. This grant is valid only when the device is sold to OEM integrators. OEM manufacturers and OEM integrators are instructed to ensure that the end may not be provided with the module installation instructions. OEM integrators and End-users must be provided with transmitter operating conditions for satisfying RF exposure compliance.

ETS Product Service AG Registration number: G5M207010004-P-15 Page 1 of 8 Appendix A. Pictures ETS Product Service AG Registration number: G5M207010004-P-15 Page 2 of 8 ETS Product Service AG Registration number: G5M207010004-P-15 Page 4 of 8

SAMSUNG ELECTRO-MECHANICS CO.,LTD. 314,Maetan 3-Dong Yeongtong-Gu, Suwon, Gyunggi-Do, 442-743,South Korea Tel: +82 31 2106902 Fax: +82 31 3007900 ______________________________________________________________________ [Label Location] Description: Bluetooth Module FCC ID: E2XBTEP45C2GA

SAMSUNG ELECTRO-MECHANICS CO.,LTD. 314,Maetan 3-Dong Yeongtong-Gu, Suwon, Gyunggi-Do, 442-743,South Korea Tel: +82 31 2106902 Fax: +82 31 3007900 ______________________________________________________________________ [FCC ID Label sample] Description: Bluetooth Module FCC ID: E2XBTEP45C2GA

ETS Product Service AG Registration number: G5M207010004-P-15 Page 3 of 8 ETS Product Service AG Registration number: G5M207010004-P-15 Page 4 of 8

ETS PRODUCT SERVICE AG TEST - REPORT FCC RULES PARTS 15.247 IC RADIO STANDARDS RSS-210 Annex 8 FCC ID: E2XBTEP45C2GA Model Name: BTEP45C2GA Test report no.: G5M207010004-P-15 Certificate 1983.01 ETS STORKOWER STRASSE 38C, D-15526 REICHENWALDE B. BERLIN PRODUCT SERVICE AG PHONE +49-33631-888 00 FAX +49-33631-888 660 ETS Product Service AG Registration number: G5M207010004-P-15 Page 1 of 32 TABLE OF CONTENTS 1 General information 1.1 Notes 1.2 Testing laboratory 1.3 Details of approval holder 1.4 Application details 1.5 Test item 1.6 Test standards 2 Technical test 2.1 Summary of test results 2.2 Test environment 2.3 Test equipment utilized 2.4 General test procedure 2.5 Test results 3 Transmitter parameters 3.1 RF power output conducted 3.2 RF power output radiated (EIRP) 3.3 20 dB bandwidth 3.4 Time of occupancy (dwell time) 3.5 Number of hopping frequencies 3.6 Carrier frequency separation 3.7 Spurious emission conducted 3.8 Spurious emission radiated 3.9 Band-edge compliance 3.10 AC power line conducted emission 4 Receiver parameters 4.1 Radiated emission APPENDIX ETS Product Service AG Registration number: G5M207010004-P-15 Page 2 of 32 1 General information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the ETS PRODUCT SERVICE AG. Tester: 18.01.2007 M. Handrik Date ETS-Lab. Name Signature Technical responsibility for area of testing: 18.01.2007 N. Kaspar Date ETS Name Signature ETS Product Service AG Registration number: G5M207010004-P-15 Page 3 of 32 1.2 Testing laboratory 1.2.1 Location ETS PRODUCT SERVICE AG Storkower Straße 38c D-15526 Reichenwalde b. Berlin Germany Telephone : +49 33631 888 00 Telefax : +49 33631 888 660 1.2.2 Details of accreditation status A CCREDITED TESTING LABORATORY DAR-REGISTRATION NUMBER: DAT-P-201/96 ACCREDITED COMPETENT BODY BNETZA-REGISTRATION NUMBER: BNETZA-ZS-026/96 FCC FILED TEST LABORATORY: REG. NO. 96970 INDUSTRY CANADA FILED TEST LABORATORY R EG. NO.: IC 3470 A2LA ACCREDITED C ERTIFICATE NUMBER: 1983.01 B LUETOOTH QUALIFICATION TEST FACILITY (BQTF) ACCREDITED BY: BLUETOOTH QUALIFICATION REVIEW BOARD (BQRF) 1.3 Details of approval holder Name : Samsung Electro-Mechanics Co., Ltd. Street : 314, Maetan 3-Dong, Yeongtong-Gu Town : 442-743 Suwon, Gyunggi-Do Country : South Korea Telephone : +82-31-210-6902 Contact : Mr. J.M. Kim E-Mail : [email protected] ETS Product Service AG Registration number: G5M207010004-P-15 Page 4 of 32 1.4 Application details Date of receipt of application : 10.01.2007 Date of receipt of test item : 10.01.2007 Date of test : 11.01.2007 – 12.01.2007 1.5 Test item Description of test item : SEMCO Bluetooth Module Type identification : BTEP45C2GA Serial number : without Photos : See annex A. Technical data Frequency band : 2.4 - 2.4835 GHz Frequency Ch A : 2402 MHz Frequency Ch B : 2441 MHz Frequency Ch C : 2480 MHz Transmitter Vnom Vnom –15 % Vnom +15 % Power (ch A) : Conducted: 2.15 dBm Conducted: 2.16 dBm Conducted: 2.13 dBm Power (ch B) : Conducted: 2.15 dBm Conducted: 2.18 dBm Conducted: 2.17 dBm Power (ch C) : Conducted: 2.54 dBm Conducted: 2.52 dBm Conducted: 2.51 dBm Antenna Type : internal dipole antenna Antenna Gain : 2 dBi Power supply : 2.8 V DC Operating mode : duplex Type of modulation : FHSS Host device : none ETS Product Service AG Registration number: G5M207010004-P-15 Page 5 of 32 Classification : Fixed Device Mobile Device (Human Body distance > 20 cm) Portable Device (Human Body distance < 20 cm) Manufacturer: (if applicable) Name : Samsung Electro-Mechanics Co., Ltd. Street : 314, Maetan 3-Dong, Yeongtong-Gu Town : 442-743 Suwon, Gyunggi-Do Country : South Korea Additional information: The test sample is designed as Bluetooth device. Its pseudorandom hopping scheme, authentication, receiver parameters, synchronization procedure and other parameters are determined by Bluetooth Core Specification. ETS Product Service AG Registration number: G5M207010004-P-15 Page 6 of 32 1.6 Test standards Technical standard: FCC Parts: 15.247 IC Standards: RSS 210 Issue 6 Annex 8.1 2 Technical test 2.1 Summary of test results No deviations from the technical specification(s) were ascertained in the course : of the tests performed. or The deviations as specified in 2.5 were ascertained in the course of the tests … performed. 2.2 Test environment Temperature : 25 ° C Relative humidity content : 20 ... 75 % Air pressure : 86 ... 103 kPa Details of power supply : 2.8 V DC Extreme conditions parameters: : test voltage - extreme min.: 2.4 V DC (Vnom – 15%) max: 3.6 V DC (Vnom + 15%) ETS Product Service AG Registration number: G5M207010004-P-15 Page 7 of 32 2.3 Test equipment utilized No. Test equipment Type Manufacturer ETS 0001 ESD Gun SESD 30000 Schlöder ETS 0002 Test receiver ESVP R & S ETS 0003 Diode Power Sensor NRV-Z2 R & S ETS 0004 Spektrum- and Network- Analyzer FSMS 26 R & S ETS 0005 RF amplifier matrix RSU-ETS-CTR6 ETS ETS 0006 HP-Filter H1G04G01 Microwave ETS 0007 Horn antenna AT 4004 ar ETS 0008 Antenna Loop antenna Siemens ETS 0009 Comb Generator Emitter CGE 02 York …

Text truncated - open the document above for the full version.

ETS Product Service AG Registration number: G5M207010004-P-15 Page 5 of 8 ETS Product Service AG Registration number: G5M207010004-P-15 Page 6 of 8 ETS Product Service AG Registration number: G5M207010004-P-15 Page 7 of 8 ETS Product Service AG Registration number: G5M207010004-P-15 Page 8 of 8