E2XSWL-2000P

SAMSUNG MagicLAN SWL-2000P User Manual (Ver. 1.0) 1 Notice 1 This manual cannot be reproduced in any form without the prior written permission of SAMSUNG Electro-Mechanics, Co., Ltd. SAMSUNG Electro-Mechanics, Co., Ltd. reserves the right to change this manual and the specifications to improve products without prior notice. So you can get the most recent software and user documentation for all MagicLAN products on our web site. • MagicLAN is the trademark of SAMSUNG wireless LAN. • MS-DOS, Microsoft and Windows are registered trademarks of Microsoft Corporation. All other brand and product names are trademarks of registered trademarks of their respective holders. http://www.MagicLAN.com Service Dept. +82-331-210-6805 Sales Dept. +82-331-210-6386 SAMSUNG – America Corporation Western US Marketing Office 85 Tasman Drive San Jose, CA 95134 USA Tel: (408)544-5200 Fax: (408)544-4967 Eastern US Marketing Office LanPAL AKOM Corporation 9 Parklawn Dr. Bethel, CT 06801 Tel: (203)778-9500 Fax: (203)778-9525 Copyright  1999 SAMSUNG Electro-Mechanics, Co., Ltd. All rights reserved. 2 Notice 2 The SWL-2000P complies with Part 15 of the FCC rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The SWL-2000P has been tested and found to comply with the limits for a Class B digital device and a low power transmitter, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to resolve the problem by one or more of the following measures; - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment to an output on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. 3 Important Safety Information l Read these simple guidelines. Breaking the rules may be dangerous or illegal. SAMSUNG is not responsible for any damages caused by breaking the rules. l Wireless LAN Card described in this document is approved for use in a wireless local area network. l Remember to make backup copies of important data. l When you are transferring data, keep your laptop computer stationary. Roaming between access points may break the connection. l Only qualified service personnel must repair the equipment. l All wireless devices may get interference, which could affect performance. l Use approved accessories only. Do not connect incompatible products. l Use only accessories approved by the wireless LAN Card manufacturer for use with this particular wireless LAN Card. The use of any other types will invalidate any approval or warranty applying to the wireless LAN Card, and may be dangerous, l Use only the region setting appropriate for the area where the wireless LAN Card is used at the present time. Using the card in any other region or with an incorrect region setting is prohibited and may be illegal. l Operation of any radio transmitting equipment, including a wireless LAN Card, may interference with the functionality of inadequately protected medical devices. l Do not use the wireless LAN Card on aircraft. l Do not use the wireless LAN Card at a refueling point. l Do not use the wireless LAN Card near fuel or chemicals. l Do not use the wireless LAN Card where blasting is in progress. l Do not use the wireless LAN Card when the use of wireless device may cause interference or danger. l Do not use the wireless LAN Card where the use of cellular terminals is prohibited. 4 Table of Contents 1. MagicLAN Installation .............................................................................. 7 1.1 Introduction ...................................................................................... 7 1.2 Technical Background ......................................................................... 7 1.3 MagicLAN Overview ........................................................................ 10 2. Before Installation ................................................................................. 11 2.1 What’s in your Package ..................................................................... 11 2.2 System Requirement ........................................................................ 11 3. MagicLAN Installation for Windows95/98 .................................................... 12 3.1 Installation Overview ........................................................................ 12 3.2 Hardware Installation ........................................................................ 13 3.2.1 Notebook PC Adapter Card (SWL-2000P) ......................................... 14 3.3 Software Installation ......................................................................... 15 3.3.1 Driver Setup ............................................................................. 15 3.4 MagicLAN Wireless LAN Card Properties Setup ....................................... 20 3.4.1 Before Wireless LAN Card Properties Setup ....................................... 20 3.4.1.1 Basics regarding the Properties Setup ............................................... 20 3.4.1.2 Meanings of the Properties Setup Options .......................................... 20 3.4.2 Setting Network Properties for “Peer-to-Peer” mode .............................. 21 3.5 Network Configur…

Text truncated - open the document above for the full version.

October 25, 1999 To Whom It May Concern: I would like to request the following items be confidential • Schematics • Block Diagram Thank you John Seo

2.0PRODUCT LABELING The label is made of coated polyester with permanent adhesive. The compliance statements are listed in the user’s manual. The label is placed on the top of the card as shown in figure 1. The label size is 4 x 6.3cm and it is blue with white lettering. FIGURE 1: FCC LABEL This device complies with the FCC, part 15 rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: E2XSWL-2000P FIGURE 2: LOCATION OF LABEL ON EUT Label Location

8.0PHOTOS OF TESTED EUT Figure 3: PCI Board Component Side Figure 4: PCI Board Solder Side Figure 5: Patch Antenna Front Side Figure 6: Patch Antenna Component Side Figure 7: Patch Antenna Solder Side Figure 8: Stub Antenna

 APPLICATION FOR FCC CERTIFICATION CLASS B DIGITAL DEVICE Samsung Electro-Mechanics 314, Maetan-3Dong, Paldal-Gu, Suwon, Kyunggi-Do, Korea, 442-743 +82-331-210-6662 Model: PCI Board SWL-2000P FCC ID: E2XSWL-2000P August 4, 1999 REPORT PREPARED BY: EMI Technician:Daniel W. Baltzell Administrative Writer:Melissa Fleming Rhein Tech Laboratories, Inc. Document Number: 990363 No part of this report may be reproduced without the full written approval of Rhein Tech Laboratories, Inc. This report concerns (check one):Original Grant: X Class II Change: Equipment Type: PCI Board Deferred grant requested per 47 CFR 0.457 (d) (1) (ii)?Yes:No: X If yes, defer until: Date Company name agrees to notify the Commission by: (date) of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37?Yes:No: X If no, assumed Part 15, subpart B for unintentional radiators - the new 47 CFR [10-1-90 Edition] provision.. FCC ID: E2XSWL-2000P i TABLE OF CONTENTS 1.0GENERAL INFORMATION...................................................................................................................1 1.1PRODUCT DESCRIPTION...........................................................................................................................1 1.2RELATED SUBMITTAL(S)/GRANT(S)..........................................................................................................2 1.3TEST SYSTEM DETAILS............................................................................................................................2 1.4CONFIGURATION OF TESTED SYSTEM.......................................................................................................3 1.5TEST METHODOLOGY..............................................................................................................................4 1.6TEST FACILITY........................................................................................................................................4 2.0PRODUCT LABELING.............................................................ERROR! BOOKMARK NOT DEFINED. 3.0SYSTEM TEST CONFIGURATION......................................................................................................5 3.1JUSTIFICATION.........................................................................................................................................5 3.2EUT EXERCISE SOFTWARE......................................................................................................................5 3.3SPECIAL ACCESSORIES.............................................................................................................................5 3.4CONFORMANCE STATEMENT....................................................................................................................6 4.0BLOCK DIAGRAM/SCHEMATICS OF PCI BOARD SWL-2000PERROR! BOOKMARK NOT DEFINED. 5.0CONDUCTED, FIELD STRENGTH CALCULATION, & RADIATED TEST METHODOLOGY....7 5.1FIELD STRENGTH CALCULATION..............................................................................................................7 5.2RADIATED MEASUREMENT.......................................................................................................................8 6.0CONDUCTED EMISSION DATA...........................................................................................................9 6.1CONDUCTED MEASUREMENT PHOTOS WITH PATCH ANTENNA..............ERROR! BOOKMARK NOT DEFINED. 6.2CONDUCTED MEASUREMENT PHOTOS WITH STUB ANTENNA................ERROR! BOOKMARK NOT DEFINED. 7.0RADIATED EMISSION DATA.............................................................................................................11 7.1RADIATED MEASUREMENT PHOTOS WITH PATCH ANTENNA.................ERROR! BOOKMARK NOT DEFINED. 7.2RADIATED MEASUREMENT PHOTOS WITH STUB ANTENNA...................ERROR! BOOKMARK NOT DEFINED. 8.0PHOTOS OF TESTED EUT......................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX LISTING APPENDIX A: EMISSIONS EQUIPMENT LIST.......................................................................................................13 APPENDIX B: USER’S MANUAL...................................................................................................................14 FCC ID: E2XSWL-2000P ii FIGURE INDEX FIGURE 1: FCC LABEL...................................................................................ERROR! BOOKMARK NOT DEFINED. FIGURE 2: LOCATION OF LABEL ON EUT........................................................ERROR! BOOKMARK NOT DEFINED. FIGURE 3: PCI BOARD COMPONENT SIDE.........................................................ERROR! BOOKMARK NOT DEFINED. FIGURE 4: PCI BOARD SOLDER SIDE..............................................................ERROR! BOOKMARK NOT DEFINED. FIGURE 5: PATCH ANTENNA FRONT SIDE........................................................ERROR! BOOKMARK NOT DEFINED. FIGURE 6: PATCH ANTENNA COMPONENT SIDE...............................................ERROR! BOOKMARK NOT DEFINED. FIGURE 7: PATCH ANTENNA SOLDER SIDE......................................................ERROR! BOOKMARK NOT DEFINED. FIGURE 8: STUB ANTENNA.............................................................................ERROR! BOOKMARK NOT DEFINED. TABLE INDEX TABLE 1: CONDUCTED EMISSIONS (CHANNEL 6 WITH THE STUB ANTENNA)........................................................9 TABLE 2: CONDUCTED EMISSIONS (CHANNEL 6 WITH THE PATCH ANTENNA)....................................................10 TABLE 3: RADIATED EMISSIONS (CHANNEL 6 WITH THE STUB ANTENNA).........................................................11 TABLE 4: RADIATED EMISSIONS (CHANNEL 6 WITH THE PATCH ANTENNA).......................................................12 FCC ID: E2XSWL-2000P Page 1 1.0GENERAL INFORMATION The following Application for FCC Certificatio…

Text truncated - open the document above for the full version.

6.1Conducted Measurement Photos with Patch Antenna 6.2Conducted Measurement Photos with Stub Antenna 7.1Radiated Measurement Photos with Patch Antenna 7.2Radiated Measurement Photos with Stub Antenna