EGT818TXWireless Controller

REPORT: TR054811/00132 FCC ID: EGT818TX 38 APPENDIX A OWNERS MANUAL REPORT: TR054811/00132 FCC ID: EGT818TX 39 REPORT: TR054811/00132 FCC ID: EGT818TX 40 REPORT: TR054811/00132 FCC ID: EGT818TX 41 REPORT: TR054811/00132 FCC ID: EGT818TX 42 REPORT: TR054811/00132 FCC ID: EGT818TX 43 REPORT: TR054811/00132 FCC ID: EGT818TX 44 REPORT: TR054811/00132 FCC ID: EGT818TX 45 REPORT: TR054811/00132 FCC ID: EGT818TX 46 REPORT: TR054811/00132 FCC ID: EGT818TX 47 REPORT: TR054811/00132 FCC ID: EGT818TX 48 REPORT: TR054811/00132 FCC ID: EGT818TX 49 REPORT: TR054811/00132 FCC ID: EGT818TX 50 REPORT: TR054811/00132 FCC ID: EGT818TX 51 REPORT: TR054811/00132 FCC ID: EGT818TX 52 REPORT: TR054811/00132 FCC ID: EGT818TX 53 REPORT: TR054811/00132 FCC ID: EGT818TX 54 REPORT: TR054811/00132 FCC ID: EGT818TX 55 REPORT: TR054811/00132 FCC ID: EGT818TX 56 REPORT: TR054811/00132 FCC ID: EGT818TX 57 REPORT: TR054811/00132 FCC ID: EGT818TX 58 REPORT: TR054811/00132 FCC ID: EGT818TX 59 REPORT: TR054811/00132 FCC ID: EGT818TX 60 UNCERTAINTY TOLERANCE DNB Engineering’s Fullerton Facility is within acceptable uncertainty tolerances per ANSI C63.4 (1992) sections 5.4.6.1 and 5.4.6.2. ANSI C63.4 (1992) 5.4.6.1 Site Attenuation. A measurement site shall be considered acceptable for radiated electromagnetic field measurements if the horizontal and vertical NSA derived from measurements, i.e., the “measured NSA,” are within ± 4 dB of the theoretical NSA (5.4.6.3) for an ideal site. 5.4.6.1 NSA Tolerance. The ± 4 dB tolerance in 5.4.6.1 includes instrumentation calibration errors, measurement technique errors, and errors due to site anomalies. These errors are analyzed in ANSI C63.6-1988 [3], wherein it is shown that the performance of a well-built site contributes only 1 dB of the total allowable tolerance. REPORT: TR054811/00132 FCC ID: EGT818TX 61 1.1 INFORMATION PERTAINING TO EQUIPMENT MANUFACTURED AFTER COMPLIANCE TESTING It is prudent that manufacturers have an established Quality Assurance program to spot check their products on a periodic basis, either based upon time or quantities produced. Obviously, a change in the engineering design should be sufficient justification for a re-test. The Quality assurance test need not be formal Verification or Certification such as required during the initial production of the product. However, it should be sufficient in scope to assure that the EMI characteristics of the product have not changed to the degree that the product exceeds the FCC limits. If a new model of a product is produced, it must undergo full Verification or Certification testing and, in case of Certification, be filed with the FCC. It is expected that the FCC will place greater emphasis and resources in spot checking commercially available products. If a product is found not to be compliant with the Limits specified in Part 15, Subpart B. the manufacturer will be subject to the appropriate penalties imposed by the Commission. The initial Certification or Verification is sufficient to justify initial production. The additional quality assurance testing performed is the manufacturer’s responsibility to assure continued compliance.

REPORT: TR054811/00132 FCC ID: EGT818TX BLOCK DIAGRAM

REPORT: TR054811/00132 FCC ID: EGT818TX EXTERNAL PHOTOS

REPORT: TR054811/00132 FCC ID: EGT818TX ID LABEL LABELING REQUIREMENTS - per 2.1033(B)(7) Label will be constructed of 0.02-inch plastic attached as shown on the equipment with permanent adhesive. All information on the label will be etched or screened. All methods will exceed the expected lifetime of the equipment. The label will be large enough to allow all information to be readily legible. Additional Label Required Shown above is a copy of the label with the Part 15.19 Compliance Statement, Location of required information is checked “below”. The label will be placed in a conspicuous location on the device. Photograph of Label Placement and Contents Picture of EUT was scanned and picture enhanced due to Label being imprinted on unit. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

REPORT: TR054811/00132 FCC ID: EGT818TX INTERNAL PHOTOS REPORT: TR054811/00132 FCC ID: EGT818TX

REPORT: TR054811/00132 FCC ID: EGT818TX OPERATIONAL DESCRIPTION REPORT: TR054811/00132 FCC ID: EGT818TX REPORT: TR054811/00132 FCC ID: EGT818TX REPORT: TR054811/00132 FCC ID: EGT818TX

REPORT: TR054811/00132 FCC ID: EGT818TX SCHEMATICS REPORT: TR054811/00132 FCC ID: EGT818TX

REPORT: TR054811/00132 FCC ID: EGT818TX 1 CERTIFICATION FOR INTENTIONAL RADIATOR per Part 15 Subpart C (CFR 47, 15.201, - 15.209 &15.249) WIRELESS CONTROLLER Model No. Command Pro 21T18 903.0 – 927.0 MHz PREPARED FOR APPLICANT: REMTRON, INC. 1916 W. Mission Rd. Escondido, Ca 92029-1114 PREPARED BY: DNB ENGINEERING, INC. 3535 W. Commonwealth Ave. Fullerton, CA 92833 (714) 870-7781 ENGINEERING, INC. REPORT: TR054811/00132 FCC ID: EGT818TX 2 TRANSMITTAL SUMMARY Unit tested: Wireless Controller Model #: Command Pro 21T18 FCC ID: EGT818TX Specifications: ANSI C63.4 1992 and CFR 47 FCC part 15 Subpart C Purpose of Report: This report was prepared to document the status of the Wireless Controller (903-927 MHz) with requirements of the standards listed above. Requirements not applicable to EUT Part 15.37 - Not applicable Emergency Broadcast System - Not applicable Spread Spectrum Exhibit - Not applicable Scanning Receiver - Not applicable Test Summary The EUT’s compliance status according to the tests performed is as follows. REQUIREMENTSSTATUS FCC part 15 Subpart C per 15.201-, 15.209 & 15.249COMPLIANT The report shall not be reproduced, except in full, without the written approval of DNB ENGINEERING, INC. Results contained in this report relate only to the item tested. The Command Pro 21T18 met all the criteria pertaining to standards called out for testing. REPORT: TR054811/00132 FCC ID: EGT818TX 3 TABLE OF CONTENTS SectionTitlePage # 1.0 Administration Data 4 1.1.1 Request for Certification 5 1.2 Related Submittals/Grants 5 1.3 Purpose of Test 5 2.0 Test Description 6 2.1 Test Configuration 6 2.2 Equipment Description 6 2.3 Mode of Operation 6 2.4 Antenna Requirements 6 2.5 Circuit Description 6 2.6 Schematics 6 2.7 Photographs of EUT 7 - 8 3.0 Emissions 9 3.1 Radiated Emissions Test Setup and Procedure 9 3.1.1 Spuri ous Radi ati on Test Si te 9 – 10 3.1.2 Example of Calculation 11 3.1.3 Field Strength of Fundamental 11 3.1.4 Harmonic Radiated Emissions 11 3.1.5 Spurious Emissions Not Associated with Fundamental 11 Test Equipment 12 Plots for Fundamental and Harmonic Tests 13 – 14 3.1.6 Duty Cycle Correction 15 Plots for Duty cycle 16 – 17 3.1.7 Occupied Bandwidth 18 Plots for Occupied Bandwidth 19 – 26 3.1.8 Photographs of Radiated Test Setup 27 – 32 4.0 Label Requirements 33 4.1 Addition Label Required 33 4.2 Photograph of Label Placement and Contents 33 5.0 Schematics 34 - 35 Uncertainty Tolerance 36 Information Pertaining to Equipment Manufactured After Compliance Testing 37 Appendix A Owners Manual 38 – 58 REPORT: TR054811/00132 FCC ID: EGT818TX 4 1.0 ADMINISTRATIVE DATA Certifications and Qualifications I certify that DNB Engineering, Inc conducted the tests performed in order to obtain the technical data presented in this application. Also, based on the results of the enclosed data, I have concluded that the equipment tested meets or exceeds the requirements of the Rules and Regulations governing this application. Measurement Repeatability Information The test data presented in this report has been acquired using the guidelines set forth in FCC Part 15 Subpart C (CFR 47, 15.201 – 15.209 and 15.249). The test results presented in this document are valid only for the equipment identified herein under the test conditions described. Repeatability of these test results will only be achieved with identical measurement conditions. These conditions include: The same test distance, EUT Height, Measurement Site Characteristics, and the same EUT System Components. The system must have the same Interconnecting Cables arranged in identical placement to that in the test set-up, with the system and/or EUT functioning in the identical mode of operation (i.e. software and so on) as on the date of the test. Any deviation from the test conditions and the environment on the date of the test may result in measurement repeatability difficulties. All changes made to the EUT during the course of testing as identified in this test report must be incorporated into the EUT or identical models to ensure compliance with the FCC regulations. Bryan Broaddus (Para. 1.1) Manager, Test Dept. DNB Engineering, Inc. Tel. (714) 870-7781 FAX (714) 870-5081 REPORT: TR054811/00132 FCC ID: EGT818TX 5 1.1.1 Request for Certification Per 2.1033(b)1: Applicant: Remtron, Inc. 1916 W. Mission Rd. Escondido, CA 92029-1114 Contact: Art McBride Phone: (619) 737-7800 Equipment Under Test: Wirless Controller FCC ID: EGT818TX 1.2 Related Submittals/Grants None. 1.3 Purpose of Tests The purpose of this series of tests was to demonstrate the Electromagnetic Compatibility (EMC) characteristics of the EUT. The following tests were performed: REQUIREMENTSSTATUS FCC part 15 Subpart C Per 15.201- 15.209 &15.249COMPLIANT REPORT: TR054811/00132 FCC ID: EGT818TX 6 2. TEST DESCRIPTION 2.1 Test Configuration Configuration Unit Name - Processor, Monitor Printer, Cable, etc. (indent for features of a unit) Style/Model/ Part No. Comments/ FCC ID# A Wireless Controller (903-927 MHz)Command ProEGT818TX 2.2 Equipment Description Please see Appendix A 2.3 Mode of Operation EUT was placed in three orthogonal positions to determine worst case emissions. Fresh batteries were used for final measurements. 2.4 Antenna Requirement - per 15.203 The antenna is internally fixed. 2.5 Circuit Description - per 2.1033(b)4 Please see Appendix A. 2.6 Schematics Please see section 5.0 REPORT: TR054811/00132 FCC ID: EGT818TX 7 2.7 Photographs of EUT - per 2.1033(b)(7) REPORT: TR054811/00132 FCC ID: EGT818TX 8 Photographs of EUT (Con’t) REPORT: TR054811/00132 FCC ID: EGT818TX 9 3. EMISSIONS Per FCC Part 15 Subpart C 3.1 Radiated Emissions Test Setup and Procedure - Per 2.1033(b)(6) Per 2.947(a) The EUT was placed on a wooden table 1 meter wide and 1.5 meters long, which rests on a low profile, steel-top turntable in a semi-anechoic test site. The top of the table is 80 cm above the ground plane. The turntable can be rotated 360 degrees. Measuring antenna is set at the pres…

Text truncated - open the document above for the full version.

REPORT: TR054811/00132 FCC ID: EGT818TX 18 REPORT: TR054811/00132 FCC ID: EGT818TX 19 REPORT: TR054811/00132 FCC ID: EGT818TX 20 REPORT: TR054811/00132 FCC ID: EGT818TX 21 REPORT: TR054811/00132 FCC ID: EGT818TX 22 REPORT: TR054811/00132 FCC ID: EGT818TX 23 REPORT: TR054811/00132 FCC ID: EGT818TX 24 REPORT: TR054811/00132 FCC ID: EGT818TX 25 REPORT: TR054811/00132 FCC ID: EGT818TX 26 3.1.8 Photographs of Radiated Test Setup – per 2.1033(b)(7) Radiated Emissions, Fundamental Horizontal Polarization EUT in position 1 REPORT: TR054811/00132 FCC ID: EGT818TX 27 Radiated Emissions, Fundamental Vertical Polarization EUT in position 2 REPORT: TR054811/00132 FCC ID: EGT818TX 28 Radiated Emissions, Harmonics Horizontal Position EUT in position 1 REPORT: TR054811/00132 FCC ID: EGT818TX 29 Radiated Emissions, Harmonics Vertical Polarization EUT in positon 2 REPORT: TR054811/00132 FCC ID: EGT818TX 30 Close up view EUT in position 1 REPORT: TR054811/00132 FCC ID: EGT818TX 31 Close up view EUT in position 2 REPORT: TR054811/00132 FCC ID: EGT818TX 32 1. LABELING REQUIREMENTS - PER 2.1033(B)(7) Label will be constructed of 0.02-inch plastic attached as shown on the equipment with permanent adhesive. All information on the label will be etched or screened. All methods will exceed the expected lifetime of the equipment. The label will be large enough to allow all information to be readily legible. 1.1 Additional Label Required Shown above is a copy of the label with the Part 15.19 Compliance Statement, Location of required information is checked “below”. The label will be placed in a conspicuous location on the device. 1.2 Photograph of Label Placement and Contents Picture of EUT was scanned and picture enhanced due to Label being imprinted on unit. This device complies with Part 15 of the FCC Rules. Operation is subject to the f o llo wing two co nditio ns: (1) This device may no t cause harmf ul interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. REPORT: TR054811/00132 FCC ID: EGT818TX 33 REPORT: TR054811/00132 FCC ID: EGT818TX 34 2. SCHEMATIC DIAGRAMS REPORT: TR054811/00132 FCC ID: EGT818TX 35 REPORT: TR054811/00132 FCC ID: EGT818TX 36 UNCERTAINTY TOLERANCE DNB Engineering’s Fullerton Facility (semi-anechoic 3 meter chamber) is within acceptable uncertainty tolerances per ANSI C63.4 (1992) sections 5.4.6.1 and 5.4.6.2. ANSI C63.4 (1992) 5.4.6.1 Site Attenuation. A measurement site shall be considered acceptable for radiated electromagnetic field measurements if the horizontal and vertical NSA derived from measurements, i.e., the “measured NSA,” are within ±4 dB of the theoretical NSA (5.4.6.3) for an ideal site. 5.4.6.1 NSA Tolerance. The ±4 dB tolerance in 5.4.6.1 includes instrumentation calibration errors, measurement technique errors, and errors due to site anomalies. These errors are analyzed in ANSI C63.6-1988 [3], wherein it is shown that the performance of a well-built site contributes only 1 dB of the total allowable tolerance. REPORT: TR054811/00132 FCC ID: EGT818TX 37 INFORMATION PERTAINING TO EQUIPMENT MANUFACTURED AFTER COMPLIANCE TESTING It is prudent that manufacturers have an established Quality Assurance program to spot check their products on a periodic basis, either based upon time or quantities produced. Obviously, a change in the engineering design should be sufficient justification for a re-test. The Quality assurance test need not be formal Verification or Certification such as required during the initial production of the product. However, it should be sufficient in scope to assure that the EMI characteristics of the product have not changed to the degree that the product exceeds the FCC limits. If a new model of a product is produced, it must undergo full Verification or Certification testing and, in case of Certification, be filed with the FCC. It is expected that the FCC will place greater emphasis and resources in spot checking commercially available products. If a product is found not to be compliant with the Limits specified in Part 15, Subpart B. the manufacturer will be subject to the appropriate penalties imposed by the Commission. The initial Certification or Verification is sufficient to justify initial production. The additional quality assurance testing performed is the manufacturer’s responsibility to assure continued compliance. REPORT: TR054811/00132 FCC ID: EGT818TX 38 Appendix A

REPORT: TR054811/00132 FCC ID: EGT818TX TEST SETUP PHOTOS REPORT: TR054811/00132 FCC ID: EGT818TX REPORT: TR054811/00132 FCC ID: EGT818TX