EILPGRM-2IN GROUND POOL ALARM

RF LABORATORIES, INC 1412 Center Avenue • Oostburg, Wisconsin 53070 (920) 564-2700 • FAX (920) 564-1027 • e-mail: [email protected] Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: EILPGRM-2. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Schematic.pdf Block Diagram.pdf Operational Description.doc The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Pursuant to DA 04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Internal Photos External Photos Poolguard_Inground_Manual_Rev_10.25.07.pdf The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, David J. Zima Attached: Copy of FCC Confidentiality Policy

APPLICANT: PBM INDUSTRIES INC. FCC ID: EILPGRM-AG EXTERNAL PHOTOS

APPLICANT: PBM INDUSTRIES INC. FCC ID: EILPGRM-AG INTERNAL PHOTOS

APPLICANT: PBM INDUSTRIES, INC. FCC ID: EILPGRM-2 REPORT: P\PBM_EIL\3874UT7\3874UT7TestReport.doc Page 2 of 18 mdea 09.20.2007 FCC PART 15.231 TEST REPORT LOW POWER UNLICENSED TRANSMITTER Applicant PBM INDUSTRIES, INC. Address 1150 WEST JFG DRIVE NORTH VERNON IN 47265 USA FCC ID EILPGRM-2 Product Description ABOVE GROUND POOL ALARM Date Sample Received 12/19/2007 Date Tested 12/28/2007 Tested By NAM NGUYEN Approved By MARIO DE ARANZETA Timco Report No. 3874UT7TestReport.doc Test Results Pass Fail THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. 849 NW STATE ROAD 45 NEWBERRY, FL 32669 USA PH: 888.472.2424 OR 352.472.5500 FAX: 352.472.2030 EMAIL: [email protected] HTTP: //WWW.TIMCOENGR.COM Certificate # 0955-01 APPLICANT: PBM INDUSTRIES, INC. FCC ID: EILPGRM-2 REPORT: P\PBM_EIL\3874UT7\3874UT7TestReport.doc Page 3 of 18 mdea 09.20.2007 TABLE OF CONTENTS GENERAL REMARKS ....................................................................................................4 REPORT SUMMARY ......................................................................................................5 TEST ENVIRONMENT....................................................................................................5 TEST SETUP .................................................................................................................5 DUT SPECIFICATION ....................................................................................................6 MANUFACTURE DECLARATION OF COMPLIANCE WITH PART 15.231(A)......................7 TEST EQUIPMENT LIST ................................................................................................8 TEST PROCEDURES .....................................................................................................9 RADIATION INTERFERENCE .......................................................................................10 CALCULATION OF DUTY CYCLE .................................................................................12 OCCUPIED BANDWIDTH.............................................................................................17 POWER LINE CONDUCTED INTERFERENCE ..............................................................18 APPLICANT: PBM INDUSTRIES, INC. FCC ID: EILPGRM-2 REPORT: P\PBM_EIL\3874UT7\3874UT7TestReport.doc Page 4 of 18 mdea 09.20.2007 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. The test results only relate to the item tested. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Testing Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Mario de Aranzeta C.E.T. Compliance Engineer/ Lab. Supervisor Date: 1/8/08 APPLICANT: PBM INDUSTRIES, INC. FCC ID: EILPGRM-2 REPORT: P\PBM_EIL\3874UT7\3874UT7TestReport.doc Page 5 of 18 mdea 09.20.2007 REPORT SUMMARY Applicable Rule(s) FCC Pt 15.231, Pt 15.209, Pt 15.207, ANSI C63.4: 2003 TEST ENVIRONMENT Test Facility The test sites are located at 849 NW State Road 45 Newberry, FL 32669 USA. Test Condition: Temperature: 26ºC Relative humidity: 50% TEST SETUP Test Exercise (e.g software description, test signal, etc.): The DUT was placed in continuous transmit mode of operation. Deviation from the standard(s) No deviation from the standard(s) Modification to the DUT: No modification was made to the DUT. Supporting Peripheral Equipment Not applicable. The device is a stand-alone remote control radio. APPLICANT: PBM INDUSTRIES, INC. FCC ID: EILPGRM-2 REPORT: P\PBM_EIL\3874UT7\3874UT7TestReport.doc Page 6 of 18 mdea 09.20.2007 DUT SPECIFICATION Applicant PBM INDUSTRIES, INC. Description ABOVE GROUD POOL ALARM FCC ID EILPGRM-2 Model Number PGRM-2 Frequency Range 433.92 MHz 110–120Vac/50– 60Hz DC Power DUT Power Source Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable APPLICANT: PBM INDUSTRIES, INC. FCC ID: EILPGRM-2 REPORT: P\PBM_EIL\3874UT7\3874UT7TestReport.doc Page 7 of 18 mdea 09.20.2007 MANUFACTURE DECLARATION OF COMPLIANCE WITH PART 15.231(A) Item Description Yes No 1 Does this device transmit a signal that is only used to control another device? X 2 Does this device send data with this control signal? X 3 Does this device send data? Data is, things like: temperature, wind direction, fluid amount, rate of flow, etc. X 4 Does this device transmit continuously or automatically? X 5 If manually operated does this device stop transmitting within 5 seconds of releasing the button? X 6 If automatically operated does it deactivate 5 seconds after activation? N/A N/A 7 Does it transmit at regular predetermined intervals? X Does it poll or send supervisory information? X 8 If yes does it do a system integrity check? How often? X Is this a fire, security or safety of life device? X 9 If YES does the device stop transmitting after the alarm condition is satisfied? X Duty cycle: Maximum on-time? 10ms If YES, on-time in 100 ms? If Other, please specify here X 10 On time in 11 Modulation technique: Please specify the modulation of the test sample, FM, or AFSK, or FSK, or on-off keying, or others? OOK APPLICANT: PBM INDUSTRIES, INC. FCC ID: EILPGRM-2 REPORT: P\PBM_EIL\3874UT7\3874UT7TestReport.doc Page 8 of 18 mdea …

Text truncated - open the document above for the full version.