EP78TQLVR-850MARINE TRANSCEIVER

MODEL LVR-850 VHF DSC RADIO OWNER’S QUICK GUIDE Pony Electric Corporation October 28, 2004 FCC RF EXPOSURE COMPLIANCE REQUIREMENTS When operating your marine radio transceiver, you should know that the antenna radiates radio frequency energy. This radio was designed to meet the FCC’s rules and regulations for the maximum permissible exposure to radio frequency energy. This design was tested and found to be compliant to the strict requirements established by the FCC. DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically authorized by the manufacturer to use with this radio. DO NOT transmit for more than 50% of the total radio use time. Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” is displayed on the screen. You can cause the radio to transmit by pressing the “PTT” switch. IMPORTANT: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 91 cm (37 inches) from all persons (including passengers) and must not exceed an antenna gain of 3 dBi and must not be co-located or operating in conjunction with any other antenna or transmitter. DSC USA DSC MON PRI GPS BASIC RADIO OPERATIONS : TURN ON : SQUELCH Adjust : Turn the SQuelch knob CCW until noise is heard. Turn the SQuelch knob CW about 1/8 turn until noise stops. Turn VOLume knob CW past the "click" position. LCD comes ON & the LCD screen shows with the DSC software version number displayed for -1 second. The Priority channel is the default channel selected (CH16 or 09) and is displayed in the LCD. For the first time Turn On, CH16 is used. The radio’s lighting is always ON. There is no contrast control. H/LWX16/9 SCNMEM CALL U I C KEYPAD Usage : MMSID Set : A friendly tone is emitted when any of the 8 keys are pressed. A 3-beep error tone is emitted if the key press is not allowed. Some functions require a holding down of a key. A single beep is emitted, then after the hold down timeout, a second friendly beep will be heard and the mode entered. See the example under Priority Channel Set below. Your MMSID number is like your home phone number. Other DSC rdios must enter your number before they can call you. Likewise, you must enable your radio to recognize your own MMSID. You only have 1 chance to enter the MMSID into your radio. Please study this section and do it properly. In case that the MMSID number is not set up, "ID" annunciator on the main screen will blink. Page 1 MEM DSC ID DSC ID DSC ID DSC ID DSC ID DSC ID DSC ID DSC ID DSC ID DSC ID **************************************** SPECIAL NOT ************************************** ******************************************************************************************************* If a 9-digit MMSID number has not been set into the radio, no DSC calls are allowed. To enter your assigned MMSID number, follow these steps. There is only 1 chance to do this procedure correctly. Page 2 Hold Down the CALL key for 5 seconds. The "ID" annunciator will blink during the entry period and the number "0" is in the Big Digit and the number "16" is in the small digit. If a valid MMSID is already entered & stored into the radio’s memory, changed to ON/OFF switching of DSC Monitor and a new MMSID entry is inhibited. The Big Digit is the MMSID number that you are setting and the small digit is the MMSID’s charactor field position. For example - "2" in the small digit represents the 2nd number from the left in your assigned MMSID, a "4" is the 4th number from the left, etc. Press the UP/DWN key to set proper MMSID data. After correct verification of EACH MMSID number by you, touch the MEM key to advance. The small digit now displays the 2nd charactor position with a "0" in the Big Digit and "2" in the Small Digit. Press the UP/DWN key to set the MMSID = "992344513" "START" "9" "2" "3" "9" "3""4" "4""5""1" DSC ID (Shows the first digit 9 automatically) Wx ALERT USA SCN DSC MON PRI P GPS Page 3 second MMSID digit and touch the MEM key to store. Repeat the operation until all 9 digits have been entered and verified by you. By pressing the MEM key, all 9 digits will flash across the screen for your review. There is no backup or edit mode. If there is an error in the entery procedure, press the 16/9 Key to edit this procedure or simply turn the radio OFF. No MMSID number will be stored. After you are completely satisfied with your entered MMSID number, Hold Down the CALL key for 5 seconds to store the number. The "ID" annuciators now stop blinking & the radio reverts to the MAIN screen. DSC call can now be made. SELECT Channels : Use the UP/DWN key to select the channel. Refer to the enclosed channel chart for proper usage and understanding. In USA & Canada, the Wx channels are available. Wx channels are not available for the International Channel Bank. The "A" annunciator in the Radio’s LCD indicates an "ALTERNATE" Channel usage and usually indicates a SIMPLEX channel is tuned and normal voice ship-to-ship communication is appropriate. If the "A" annunciator is OFF, the radio is sometimes operating in the DUPLEX Mode - the Transmit and Receive frequencies are different. CHANNEL Bank : Press and hold the HI/LO key & Wx key at the same time to switch channel banks - USA, Int’l, & Canada. Refer to the channel chart appendix for proper usage. The selected "USA", "INT" or "CNA" annunciator will come ON. Wx and Wx Alert : This key is used to enter the Wx mode. The last used Wx channel always appears first. Use the UP/DWN key to change the Wx channel. In Priority Scan or Memory Scan Modes, a press of the Wx key allows the Wx Alert function to be toggled ON/OFF. The scanning temporality stops & the "Wx ALERT" annunciator will blink twice before the scan continues. Thi…

Text truncated - open the document above for the full version.

BOM_LVR-850-2(Final).xls 1/1 REV 11111111152112131 REV REV L205L201 203 204T101L106 107L210L202L206 207 SSTCQMitsumiMitsumiMitsumiSSTSSTSSTSST 032303130384022102860276031403140314 C14027AC14030AC54048AC24023AC34053AC14029AC14028A X14042A C34038A X201L101 102 103 104 105IC201IC102D401 F24651AF14027B RectronCQ F101 F34651A X14037A 0331038203830357 D54002A ToshibaSanyo U24003AU31040A P-41061 (Z-48)P-40172 Rev1 #3 (C-029) P-40172 Rev1 #2 (C-028) P-40172 Rev1 #1 (C-027) P-40173 Rev1 #1 (C-030) (R-038) (I-023) (R-053)LTWM450E3.579545MH  JTBM450C2420.950MHz RL25221M15BS-AV35LA4425A Choke TransAir CoilAir CoilAir CoilAir CoilCoil RF Coil IFCoil RF(VCO) Z1032 7 X Smart Far REV PC Board Main (PGB-40017) LVR-850 P-41398 DESCRIIPTION MFG SYMBOL PARTS No. APPR. No. Q'ty X-tal X-tal DSGD. X-tal Filter DRWN No./SPECIFICATION REV RECORD DATE APPRD. DATE REV RECORD CHKD. APPRD. APPRD. DRWN No. PT-13 Ceramic FilterCeramic DiscriminatorPower ModuleICDiode MODEL No. LVR-850 Parts List (Electr) F103F104X301 TITLE CQCQCQ BOM_LVR-850-2(Final).xls 1/1 RE V 1 PCBA 1 PCBA 1 PCBA 1 PCBA 1 PCBA 1 PCBA 1 PCBA 5 PCBA 1 PCBA 4 PCBA 1 PCBA 5 PCBA 1 PCBA 1 PCBA RE V PAGE REV REV Electrolytic Cap. TITL E Electrolytic Cap.Electrolytic Cap.Electrolytic Cap.Electrolytic Cap.Electrolytic Cap. Parts List (Electr) PONY ELECTRIC DATE 10/27/04 2/10 DRWN No. PT-1341 MODEL No. APPRD. DSGD. CHKD. A PPRD. REV RECORD DATE APPRD. REV RECORD DATE Remarks DRWN No./SPECIFICATION SYMBOL Assy Carbon ResistorCarbon Resistor LVR-850 Carbon Resistor PARTS No. APPR. No. Q'ty MFG REV Carbon Resistor Z0 25 DESCRIIPTION R14101A HK Resistor 101 HK Resistor R14107B Electrolytic Cap.Electrolytic Cap.VolumeVolume CF25 47 JCF25 3.9K JCF100 15 J PR-M Type1C UTES 222M1C UTES 102M1C UTES 101MRD901S-20-15K-A10KRD901-20-15K-B20K1C UTES 470M1C UTES 330M E24013C 1C UTES 100M1E UTES 4R7M1H UTES 010M HK ResistorHK Resistor R14113AR14112AE24019CE24018CE24014C ToshinToshinToshin E24021C ToshinToshin 105220R403C406C140C142C133 242 308 330 402C306 E24020CE24022C E24006AP14438BP14437B 03800381 ToshinToshinToshinAlphaAlpha C217 316 334 409C315C132 134 135 319 236VR002VR001 BOM_LVR-850-2(Final).xls 1/1 RE V 1 PCBA 1 PCBA 2 PCBA 1 PCBA 1 PCBA 1 PCBA 1 PCBA 3 PCBA 3 PCBA 1 PCBA 4 PCBA 1 PCBA 1 PCBA 2 PCBA 1 PCBA 1 PCBA 2 PCBA 6 PCBAPCBA 1 (47k) PCBA 4 (4.7k) PCBA 1 PCBA RE V PAGE REV REV ICICFET TITL E FETTransistorTransistorTransistorTransistor Parts List (Electr) PONY ELECTRIC DATE 10/27/04 3/10 DRWN No. PT-1341 MODEL No. APPRD. DSGD. CHKD. A PPRD. REV RECORD DATE APPRD. REV RECORD DATE Remarks DRWN No./SPECIFICATION SYMBOL Assy ICIC LVR-850 IC PARTS No. APPR. No. Q'ty MFG REV IC TA31136FN DESCRIIPTION  U31010A Toshiba IC101 TransistorTransistorTransistorDiodeDiodeDiodeTrimmer Pot. MeterTrimmer Pot. MeterCeramic Trimmer M64082AGP-603CNJM4558MNJM567MNJM7805DL1AMSM7512BGS-KRD00HVS12SK882Y2SC2712Y2SC2714Y2  4713  2SA1162Y2SA1681RN2423RN1402HVU131HVU350B1SS352RH03ADCS4RH03ADCS3TZC03R-100A-110 U31007X U31002BU31008A  U31039A U31011A JRCMitsubishiJRCJRCOki T51003AT51001A MitsubishiToshiba T31002A T31007A T31003A ToshibaRohmToshiba IC203IC301 302IC202IC401IC303Q201Q101 102 204Q301 302 305Q205Q103 202 203 206 T11001AT11002AT61003AT61006A D11005AD41001AD11004A B21006AB21005AB11001A ToshibaToshibaToshibaToshibaHitachiHitachiToshibaAlpsAlpsMurata Q104Q303Q401 402Q403D101 D202 203D201 301 302 402 403D303VR201VR202 301 302 303VC201 BOM_LVR-850-2(Final).xls 1/1 RE V 2 PCBA 2 PCBA 1 PCBA 2 PCBA 1 PCBA 1 PCBA 13 PCBAPCBAPCBA 2 PCBA 1 PCBA 18 PCBAPCBAPCBAPCBA 1 PCBA 35 PCBAPCBAPCBAPCBAPCBAPCBAPCBA RE V PAGE REV REV GRM188B11H102K E11201A Murata C421 422 204 247 248 C148 150 205 209 212C214 215 218 224 238C239 240 301 302 307C321 331 404 407 408 C326 332 333 C325 C410 411 418 419 420 C106 144 145 146 147 InductorInductorCeramic Cap. C241304 312 320 324 Ceramic Cap.Ceramic Cap.Ceramic Cap. TITL E Parts List (Electr) PONY ELECTRIC DATE 10/27/04 4/10 DRWN No. PT-1341 MODEL No. APPRD. DSGD. CHKD. A PPRD. REV RECORD DATE APPRD. REV RECORD DATE Remarks DRWN No./SPECIFICATION SYMBOL Assy Capacitor TantalumCapacitor Tantalum LVR-850 Capacitor Tantalum PARTS No. APPR. No. Q'ty MFG REV Capacitor Tantalum ECST1AY106R DESCRIIPTION E31305A Matsushita C123 226 Ceramic Cap.Ceramic Cap. ECST1CY225RECST1EY105RECST1VY224RLQH1N4R7K04LQH1N1R0K04GRM188B11E104KGRM188B11H333KGRM188B11H103KGRM188B11H223K E31204AE31102AE31003A C41001A E11401A C41002A GRM188B11H222K MatsushitaMatsushitaMatsushitaMurataMurataMurata E11303A Murata L208C120 122 124 127 128 C129 137 232 311 317 C318 401 403 C230 233C234C231 235L209C313 323 C322C107 114 115 118 119 MurataMurata E11302AE11301AE11203A C131 136 139 143 228 Murata BOM_LVR-850-2(Final).xls 1/1 RE V 1 PCBA 8 PCBAPCBA 1 PCBA 1 PCBA 2 PCBA 1 PCBA 1 PCBA 3 PCBA 1 PCBA 3 PCBA 5 PCBA 1 PCBA 4 PCBA 3 PCBA 1 PCBA 3 PCBA 2 PCBA 1 PCBA 2 PCBA 2 PCBA 1 PCBA RE V PAGE REV REV Ceramic Cap. TITL E Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap. Parts List (Electr) PONY ELECTRIC DATE 10/27/04 5/10 DRWN No. PT-1341 MODEL No. APPRD. DSGD. CHKD. A PPRD. REV RECORD DATE APPRD. REV RECORD DATE Remarks DRWN No./SPECIFICATION SYMBOL Assy Ceramic Cap.Ceramic Cap. LVR-850 PARTS No. APPR. No. Q'ty MFG REV DESCRIIPTION Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap. GRM1882C1H681JGRM1882C1H221JGRM1882C1H121J Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap.Ceramic Cap. GRM1882C1H180JGRM1882C1H100DGRM1882C1H101JGRM1882C1H470JGRM1882C1H330JGRM1882C1H270JGRM2162C1H8R0DGRM1882C1H2R0CGRM1882C1H1R0CGRM1882C1HR50CGRM216B11H102KGRM2162C1H220JGRM2162C1H150JGRM1882C1H7R0DGRM1882C1H6R0DGRM1882C1H5R0DGRM1882C1H220J E11111AE11105A Murata MurataMurataMurata E11018AE11016AE11015A MurataMurataMurata E11101AE11014AE11013AE11102A MurataMurataMurata C314C125 126 412 413 414 C415 416 417 C130C244C211 243C216 C101 C225 327 328C102C121 213 245 E11010AE11008AE11007AE11006AE11003AE11002AE11001AE12201AE12014AE12012AE12009A MurataMurataMurataMurataMurataMurataMur…

Text truncated - open the document above for the full version.

H/L BATT+ BEEP +12V SP H/L RD BEEP-C HI/LO UP DOWN H/L LOCK-P WX BEEP-C COM0 COM1 S19 S22 S23 UPH/LWX 16/9 SCAN MEMDISTCALL S10S11 S12 S13 S14 S15S16 S17 S18 S20 S21 S24 S25 S26 HI/LO MUTE-C TX/RX WX 16/9 SCAN MEM CALL DIST XD BEEP out S9S8 S7 S6 S5 S4 S3 S2 S1 S0 VCOM VTX VCC WX H/L DOWN DATA OUT NMEA IN MUTE BATT+ T/R PTT RS XD RD LOCK-P +5V VCOM VRX VRX SQ WX BEEP H/L VCC(+12V) SP LOCK-P XD VCOM(+5V) T/R MUTE NMEA- DATA+ S27 S9 S22 S10 S19 S14S11 S15 S21 S12 S13S4S27 S19 S14S21S22 S0 S26 S16 S20S7 S0 S1 S17S18 S23 S25 S24 COM0 COM1 S23S20S18S17 S12 S13 S11S10 S9 S1 S8S5S4S3S6S2 PTT NMEA+ DATA- SQ MUTE WX PTT RD H/L BEEP VRX VTX VTX VCOM VCOM XD RD SQ MIC T/R MUTE WX SQN SQN SQ LOCK-PMOD1/RS XD RD PTT VCOM VCOM MIC MOD1/RS MOD1/RS MOD1 MUTE-C TX/RX DATA CLOCK RESET RESETCLOCK DATA RESET CLOCK DATA RESET DATA CLOCK VTX VRX MOD CONT KEY MOD PLL CONT PLL MOD LCD LCD MOD KEY MOD PLL CONT PLL KEY CAP CONT CONT MOD PLL [RX Local Freq] TP-1 [ LO ][ HI ] [DEVIATION] BATT+ WHITE BLACK [WX ALERT] MAIN PCB P - 3 0 5 4 2 EXT Speaker LOWRANCE CPU PCB VHF DSC RADIO [KEY] W14212AW14212A W14213A SWITCH VOLUME SQUELCH [LCD] HI POWER [LO] UNLOCK [HI] LVR - 8 5 0 [VCO ] TP3 TP2 [IF OUT] [ch70 DEVIATION] MIC RX [HI] (PGB-40014) (PGB-40015) Oct.12,2004 (PGB-40016) BATT+ SW501 SW502 SW503 SW504 SW505 SW506 SW507 SW508 SW509 MIC GND PTT SP TP6 TP5 TP4 TP7 BATT- 1212 COM L105 R038 L104 R038 L103 R038 L101 R038 L102 R038 C124 104 IC102 LA4425A 1 IN+ 2 IN- 3 GND 4 OUT 5 Vcc T101Z-48 D101 HVU131 R231 1K R202 470 R230 680 C214 102 C222 1P C201 6P D201 1SS352 C205 102 C207 6P R206 47 C224 102 C228 103 R215 2.2K C221 2P C301 102 C302 102 R302 2.2K C307 102 VR301 5K 3 1 R304 470 R317 10K C311 104 C317 104 IC301A NJM4558M 2 3 4 1 8 C313 333 R307 2.7K VR302 5K 1 3 R306 33K R312 470 C312 103 IC504 PS2701 43 2 1 +12V +12V C103 1P C107 103 R104 100 C109 0.5P C110 0.5P C111 10P C114 103 R106 2.2K R118 2.2K C125 220P C126 220P R116 22K C127 104 C131 103 R121 22K R122 47K Q104 2SA1162Y R124 1.5K R125 1K R126 4.7K R127 390K C143 103 C209 102 R214 33K R218 3.9K C232 104 R225 1.8K VR202 5K 1 3 R227 150K R229 1.5K C238 102 R228 330 C240 102 C241 103 C243 47P C245 15P C211 47P R203 4.7 C212 102 Q201 RD00HVS1 C213 15P D302 1SS352 C304 103 R301 22K Q301 2SC2712Y Q302 2SC2712Y Q303 2SA1681Y C308 47uF/16 + R305 33K C306 33uF/16 + L210 R053 C226 10uF-T + C231 0.22uF-T + C242 47uF/16 + C142 100uF/16 + C140 1000uF/16 + C133 47uF/16 + R308 10K R309 10K IC301B NJM4558M 7 5 6 R310 8.2K R322 10K C322 223 R321 15K C324 103 VR303 5K 1 3 C327 22P C328 22P X301 3.579545MHz C331 102 R329 100K R514 10K R516 22K R512 470 D501 1SS352 C513 100P R508 2.2K R509 1K R510 10K Q505 2SA1162Y D502 1SS352 R511 470 C501 22P C502 22P C503 104 C508 104 R501 10K C510 104 R504 10K R502 10K R503 10K C505 103 C506 103 R123 5.6K C239 102 R119 22K R114 3.3K R115 10K IC401 NJM7805DL1A 3 O 2 G 1 I C132 1uF/50 + C134 1uF/50 + C135 1uF/50 + C315 4.7uF/25 + VC201 10P C314 680P D402 1SS352 D403 1SS352 R402 10K C404 102 Q401 RN2423 C150 102 C234 1uF-T + R120 120K R505 10K R507 10K R506 10K R108 100 L106 I-023 Q103 2SC2714Y R111 680K L107 I-023 R112 330 C118 103 C119 103 C115 103 C116 6P C139 103 C136 103 C419 C420 D202 HVU350B D203 HVU350B X501 4.91520MHz IC503 PST600CM 3 O 2 G 1 Vcc C512 104 J102 123456789 L202 C-029 L205 C-027 L201 C-030 L203 C-030 L204 C-030 L206 C-028 L207 C-028 F103 LTWM450E 1 3 4 5 2 F104 JTBM450C24 R518 2.2K R519 2.2K VR201 50K 3 1 R326 10K C507 10uF-T + C511 10uF-T + C517 10uF-T + C147 102 IC502 S-93C56BD01-T8T1 1 CS 2 SK 3 DI 4 DO 5 GND 6 NC 7 NC 8 Vcc C515 102 C401 104 C403 104 D401 RL252 C406 2200uF/16 + C407 102 J505 B4B-ZR 1234 C514 100P C518 100P IC202 NJM567M 1 Fout 2 LPF 3 IN 4 V+ 5 TIM R 6 TIM C 7 GND 8 OUT C235 0.22uF-T + R226 22K C236 1uF/50 + C421 C422 102 C148 102 VR002 10KA 4135 VR001 20KB 13 C146 102 J103 87654321 C145 102 C144 102 C219 10P L209 4R7 C248 102 J001 ANTENNA R403 CF100-15 P103 12345 P104 123 C504 104 C509 104 C113 10P Q102 2SK882Y C106 102 R103 680 Q101 2SK882Y C102 18P C105 6P C108 10P C112 10P R110 1K C121 15P C128 104 C122 104 C123 10uF-T + R117 150 C120 104 R113 220K C216 33P C217 10uF/16 + R207 8.2K C215 102 R209 330 C206 22P-40 R201 10K IC201 S-AV35 4 3 5 2 1 OUT IN VCC VCON GND Q202 2SC2714Y Q2032SC2714Y Q204 2SK882Y Q205 2SC4713K Q206 2SC2714Y R204 3.3K R205 2.2K R208 3.3K R210 100K R221 47K C233 2.2uF-T + R223 4.7K R222 22K C225 22P R213 100 R217 47K Q403 RN1402 C418 C410 102 R401 1K C402 47uF/16 + R404 680 C408 102 C409 10uF/16 + R517 2.2K Q305 2SC2712Y R515 1K R522 22K Q506 2SC2712Y R513 10K D504D503 FA1101F R520 2.2K D505 SML-310MT D506 D507 SML-310MT D508 C001 15P-40 C202 22P-40 C208 1P C210 15P-40 C237 8P-40 C203 102-40 C130 120P D301 1SS352 D303 1SS352 C247 102 R211 330 C218 102 L208 1R0 Q501 RN1411 Q502 RN1411 Q503 RN1411 Q504 RN1411 SP1 F17M-4961 LCD1 TCM-4215 26 ***/DISTRESS 27 ***/LAST 28 ***/NEW 29 ***/GEO 30 1E/DIR 31 1D/ALLSHIP 32 COM0/+++ 33 ***/COM1 34 NC 35 NC 36 1C/+++ 37 2G/+++ 38 2E/+++ 39 2D/+++ 40 3F/+++ 41 3G/+++ 42 3E/+++ 43 3D/+++ 44 3C/+++ 45 3B/+++ 46 4F/+++ 47 4E/+++ 48 4D/+++ 49 4C/PRI 50 4G/ID 25 4B/+++ 24 4A/+++ 23 3A/ACK 22 ***/MON 21 2C/DSC 20 NC 19 NC 18 2B/A 17 ***/CNA 16 2A/+++ 15 2F/+++ 14 ***/INT 13 IB/+++ 12 ***/USA 11 1A/+++ 10 1F/SCN 9 GPS 8 1G/WAIT 7 ***/P 6 ***/ALERT 5 ***/MEM 4 ***/Lo 3 ***/Wx 2 ***/TX 1 ***/ALL C204 102 R105 47(A) C230 2.2uF-T + R220 3.9K(A) C137 104 C129 104 J101 123456789 P501 987654321 P502 987654321 R101 0(A) IC101 TA31136FN 1 Xtal 2 Xtal 3 MIXo 4 V+ 5 LIMi 6 DEC 7 FILo 8 FILi 9 AFo 10 Quad 11 IFo 12 RSSI 13 Ndet 14 Nrec 15 GND 16 MIXi R316 22K C325 222 C333 103 C323 333 IC302B NJM4558M 6 5 7 R314 22K R313 22K R320 2.2K R319 10K C316 10uF/16 + C321 102 C320 103 C319 1uF/50 + R315 56K C318 104 IC302A NJM4558M 1 4 3 2 8 C332 103 R311 220K R318 100K R109 1K F101 21M15B *C413 *C414 *C415 *C416 *C417 IC501 uPD780308GC-8EU 26 COM3 27 BIAS 28 VLC0 29 VLC1 30 VLC2 31 VSS0 32 S0 33 S1 34 S2 35 S3 36 S4 37 S5 38 S6 39 S7 40 S8 41 S9 42 S10 43 S11 44 S12 45 S…

Text truncated - open the document above for the full version.

TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: [email protected] APPLICANT: PONY ELECTRIC CORPORATION FCC ID: EP78TQLVR-850 REPORT #: P\PONY_EP7\2054AUT4\2054AUT4TestReport.doc COVER SHEET Test Report Product Name: MARINE TRANSCEIVER FCC ID: EP78TQLVR-850 Applicant: PONY ELECTRIC CORPORATION NO. 202, 6-28, AKASAKA 9-CHOME MINATO-KU, TOKYO 107 JAPAN Date Receipt: DECEMBER 7, 2004 Date Tested: JANUARY 11, 2005 TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: [email protected] APPLICANT: PONY ELECTRIC CORPORATION FCC ID: EP78TQLVR-850 REPORT #: P\PONY_EP7\2054AUT4\2054AUT4TestReport.doc TABLE OF CONTENTS TABLE OF CONTENTS LIST APPLICANT: PONY ELECTRIC CORPORATION FCC ID: EP78TQLVR-850 TEST REPORT: PAGE 1............GENERAL INFORMATION & TECHNICAL DESCRIPTION PAGE 2............TECHNICAL DESCRIPTION CONTINUED RF OUTPUT POWER PAGE 3............TECHNICAL DATA PAGE 4............VOICE MODULATION CHARACTERISITICS AUDIO FREQUENCY RESPONSE PAGE 5............AUDIO LOW PASS FILTER PAGE 6............MODULATION LIMITING PAGE 7............OCCUPIED BANDWIDTH PAGE 8............OCCUPIED BANDWIDTH PLOT PAGE 9............SPURIOUS EMISSIONS AT ANTENNA TERMINALS PAGE 10...........METHOD OF MEASURING CONDUCTED EMISSIONS PAGE 11-12........FIELD STRENGTH OF SPURIOUS EMISSIONS PAGE 13...........METHOD OF MEASURING RADIATED SPURIOUS EMISSIONS PAGE 14...........FREQUENCY STABILITY PAGE 15-16........RF EXPOSURE REQUIREMENTS PAGE 17-22........LIST OF TEST EQUIPMENT EXHIBITS INCLUDING: BLOCK DIAGRAM SCHEMATIC PARTS LIST USERS MANUAL LABEL SAMPLE LABEL LOCATION EXTERNAL PHOTOGRAPHS INTERNAL PHOTOGRAPHS OPERATIONAL DESCRIPTION TUNING PROCEDURE TEST SET UP PHOTOGRAPHS TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: [email protected] APPLICANT: PONY ELECTRIC CORPORATION FCC ID: EP78TQLVR-850 REPORT #: P\PONY_EP7\2054AUT4\2054AUT4TestReport.doc Page 1 of 22 GENERAL_INFORMATION 2.1033(c) PONY ELECTRIC CORPORATION will sell the FCC ID: EP78TQLVR-850 VHF Marine transmitter in quantity, for use under FCC RULES PART 80. 2.1033(c) TECHNICAL_DESCRIPTION (4) Type of Emission: 16K0G3E/16K0F3E Bn = 2M + 2DK M = 3000 D = 5KHz (Peak Deviation) K = 1 Bn = 2(3.0K) + 2(5K)(1) = 16.0K 80.205 (a) ALLOWED AUTHORIZED BANDWIDTH = 20.00KHz. 2.1033(c)(6) Frequency Range: 156.025 – 157.425 MHz 2.1033(c)(7) Power Range and Controls: There is a user Power switch for High/Low Power. Maximum Output Power Rating: High 25 Watts, 1 Watt into a 50 ohm resistive load. 2.1033(c)(8) DC Voltages and Current into Final Amplifier: POWER INPUT FINAL AMPLIFIER ONLY High Low Vce = 13.8 Volts Vce = 13.8 VDC Ice = 5.0 A. Ice = 2.15 Pin = 69.00 Watts Pin = 29.67 Watts Function of each electron tube or semiconductor device or other active circuit device is included in the parts list exhibit. 2.1033(c)(9) Complete Circuit Diagrams: The circuit diagrams and block diagrams are included. 2.1033(c)(10) Instruction book. The instruction manual is included. TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: [email protected] APPLICANT: PONY ELECTRIC CORPORATION FCC ID: EP78TQLVR-850 REPORT #: P\PONY_EP7\2054AUT4\2054AUT4TestReport.doc Page 2 of 22 2.1033(c)(11) Tune-up procedure. The tune-up procedure is included. Description of all circuitry and devices provided for determining and stabilizing frequency is included in the circuit description 2.1033(c)(11) Digital modulation. This unit does NOT use digital modulation. The data required by 2.1046 through 2.1055 is submitted below. 2.1046(a) RF_power_output . 80.215 (e)(1) RF power is measured by connecting a 50 ohm, re- sistive wattmeter to the RF output connector. With a nominal battery voltage, and the transmitter properly adjusted the RF output measures: OUTPUT POWER: HIGH: 25 W CONDUCTED LOW: 1 W CONDUCTED 80.911 (d)(5) For primary supply voltages, measured in accordance with the procedures in this paragraph, greater than 11.5 volts, but less than 12.6 volts, the required transmitter output power shall be equal or greater than the value calculated below P = 4.375(v) – 35.313 (For 12V this equals 17.2W) METHOD OF MEASURING RF POWER OUTPUT Transmitter 50 ohm under test Resistive Wattmeter Power Supply TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: [email protected] APPLICANT: PONY ELECTRIC CORPORATION FCC ID: EP78TQLVR-850 REPORT #: P\PONY_EP7\2054AUT4\2054AUT4TestReport.doc Page 3 of 22 TECHNICAL DATA: 80.203 (b) External Controls: The transmitter is capable of changing frequency between 156.05 – 157.425 MHz by external control. The available channels are shown in the User Manual description Channel List. These channels are preprogrammed by the manufacturer and change of frequency is inaccessible to the station operator. 80.203 (c) Five minutes continuous transmission test. The antenna was connected to a dummy load and the radio was locked in a transmit PTT mode. An external timer digital clock was used to observe the duration of the un-modulated transmission. The transmitter turned off and the radio went to receive mode at 4 minutes, 58 seconds as displayed by the external digital clock. 80.203 (n) This radio complies with the requirement for DSC capability in the 156 – 162 MHz band and in accordance with 80.225. 80.873; 80.956 Transmitter G3E emission capability: The transmitter was connected to 50 ohm resistive wattmeter and the frequency was set to 156.300 and to 156.800 MHz. With normal modulation, the output power displayed was 25 Watts at the high power setting and 1 watt at low power setting, consistent with previous measurements. The transmitter has been demonstrated to be capable, with normal operating voltages applied, of…

Text truncated - open the document above for the full version.