FHO-E1205E1205 ANSLUTA

Caution: This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD Authority to Act as Agent Date: __February 27,2014_____ _ American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: ______Intertek Testing Services Shanghai______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b) , to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, _____December 31,2014____

IKEA of Sweden AB Request for Confidentiality Date: ____February 27,2014____ Subject: Confidentiality Request for: ______FCC ID:FHO-E1205; IC:10912A-E1205_____ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ ______IKEA of Sweden AB_____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __________ __________ (Signature/Title 3 ) IVAN SUSAK (Print name) 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

FCC ID: FHO-E1205 IC:10912A-E1205 Page 1 of 2 External Picture FCC ID: FHO-E1205 IC:10912A-E1205 Page 2 of 2 EUT

Label location

FCC ID: FHO-E1205 IC:10912A-E1205 Page 1 of 2 Internal Picture FCC ID: FHO-E1205 IC:10912A-E1205 Page 2 of 2

FCC ID: FHO-E1205 IC: 10912A-E1205 Page 2 of 13 Description of Test Facility Name: Intertek Testing Services Ltd. Shanghai ETL Semko Address: Building No.86, 1198 Qinzhou Road(North), Shanghai 200233, P.R. China FCC Registration Number: 236597 IC Assigned Code: 2042B-1 Name of contact: Steve Li Tel: +86 21 64956565 ext. 214 Fax: +86 21 54262335 ext. 214 FCC ID: FHO-E1205 IC: 10912A-E1205 Page 3 of 13 Content SUMMARY .......................................................................................................................................................... 1 DESCRIPTION OF TEST FACILITY ......................................................................................................................... 2 1. GENERAL INFORMATION ............................................................................................................................ 4 1.1 Applicant Information ..................................................................................................... 4 1.2 Identification of the EUT ................................................................................................ 4 1.3 Technical specification ................................................................................................... 4 1.4 Mode of operation during the test / Test peripherals used .............................................. 5 2. TEST SPECIFICATION .................................................................................................................................. 5 2.1 Instrument list ................................................................................................................. 5 2.2 Test Standard .................................................................................................................. 5 3. RADIATED EMISSION ................................................................................................................................... 7 3.1 Test limit ......................................................................................................................... 7 3.2 Test Configuration .......................................................................................................... 7 3.3 Test procedure and test setup .......................................................................................... 8 3.4 Test protocol ................................................................................................................... 9 4. ASSIGNED BANDWIDTH (20DB BANDWIDTH) ............................................................................................ 10 4.1 Limit .............................................................................................................................. 10 4.2 Test Configuration ........................................................................................................ 10 4.3 Test procedure and test setup ........................................................................................ 10 4.4 Test protocol ................................................................................................................. 10 5. POWER LINE CONDUCTED EMISSION ........................................................................................................ 11 5.1 Limit .............................................................................................................................. 11 5.2 Test configuration ......................................................................................................... 11 EMI receiver ................................................................................................................... 11 5.3 Test procedure and test set up ....................................................................................... 12 5.4 Test protocol ................................................................................................................. 12 6. OCCUPIED BANDWIDTH ............................................................................................................................ 13 6.1 Test limit ....................................................................................................................... 13 6.2 Test Configuration ........................................................................................................ 13 6.3 Test procedure and test setup ........................................................................................ 13 6.4 Test protocol ................................................................................................................. 13 FCC ID: FHO-E1205 IC: 10912A-E1205 Page 4 of 13 1. General Information 1.1 Applicant Information Applicant: IKEA of Sweden AB P.O. Box 702, S-343 81 Älmhult, SWEDEN Name of contact: Raymond Zhang Tel: 021-54252345-4075 Fax: 021-54252345 Email: [email protected] Manufacturer: IKEA of Sweden AB P.O. Box 702, S-343 81 Älmhult, SWEDEN Sample received date : January 10, 2014 Date of test : January 10-February 25, 2014 1.2 Identification of the EUT Equipment: Remote controller Type/model: E1205 ANSLUTA FCC ID: FHO-E1205 IC: 10912A-E1205 1.3 Technical specification Operation Frequency Band: 2436.27 MHz Modulation: FSK Antenna Designation: Omnidirectional antenna Gain of Antenna: 0dBi Rating: 2x1.5VDC LR03 AAA Description of EUT: There is one model only. The EUT transmits RF signal to control the working condition of the corresponding receiver. Channel Description: There is one channel only FCC ID: FHO-E1205 IC: 10912A-E1205 Page 5 of 13 1.4 Mode of operation during the test / Test peripherals used Within this test report, EUT was tested with modulation and tested under its rating voltage and frequency. For the EUT is handheld device, it was set up and tested in three axes (X, Y and Z). The three axes were tested one by one while the test receiver worked as “max hold” continuously and the highest reading among the whole test procedur…

Text truncated - open the document above for the full version.

FCC ID: FHO-E1205 IC:10912A-E1205 Page 1 of 5 Test Data FCC ID: FHO-E1205 IC:10912A-E1205 Page 2 of 5 1. Radiated emission Horizontal 0 10 20 30 40 50 60 70 80 Level [dB礦/m] 30M50M70M100M200M300M500M 700M1G Frequency [Hz] x x x x x x x x x x x MES SG0318V1_red MES SG0318V1_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: FHO-E1205 IC:10912A-E1205 Page 3 of 5 Vertical 0 10 20 30 40 50 60 70 80 Level [dB礦/m] 30M50M70M100M200M300M500M700M1G Frequency [Hz] x x x x x x x x x x x MES SG0318H1_red MES SG0318H1_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: FHO-E1205 IC:10912A-E1205 Page 4 of 5 2. Occupied bandwidth 3. Assigned bandwidth (20dB bandwidth) FCC ID: FHO-E1205 IC:10912A-E1205 Page 5 of 5 4. Duty cycle: T on time max = 0.92ms * 36 = 33.12 ms PDCF = 20log (T on time/100ms) = -9.60

FCC ID: FHO-E1205 IC:10912A-E1205 Page 1 of 3 Test Setup FCC ID: FHO-E1205 IC:10912A-E1205 Page 2 of 3 Radiated Emission 30MHz-1000MHz X axis 30MHz-1000MHz Y axis 30MHz-1000MHz Z axis FCC ID: FHO-E1205 IC:10912A-E1205 Page 3 of 3 Higher than 1GHz X axis Higher than 1GHz Y axis Higher than 1GHz Z axis