G95TWTG001WiFi Photo Frame

1 PoMMeS Multi-media Device User’s guide 2 Contents Getting Started X Introduction X PoMMeS Layout and Key Definition X Before you Begin X Parts Checklist X Important Installation Information X Important Installation Guidelines X Set Up PoMMeS Basics X PoMMeS Multi-Media Device Applications X View Useful Information Appendix 1: Important Safety Instructions Appendix 2: Troubleshooting Appendix 3: Qualifications 3 Getting Started INTRODUCTION CAUTION: When using PoMMeS, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. WARNING: To prevent fire or electrical shock hazard, do not expose this product to rain or moisture. Your PoMMeS is designed to access to a wide variety of content and applications from your service center. To get the most from your new PoMMeS, we suggest that you take a few minutes right now to read through this user’s guide. Your PoMMeS provides with the following main features: • TV programs • VoIP Video calls • Weather services • Online services • Web services IMPORTANT: Please check with your service center for service availability and compatibility with this device. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 4 Changing the Battery CAUTION: 1. Make sure the tablet is OFF. 2. Remove the battery compartment door. 3. Plug the battery pack cord into the jack inside the compartment. NOTE: To ensure proper battery installation, the connector is keyed and can be inserted only in one way. Important: Battery to properly charge (for 6 hours) prior to first use or when you install a new battery pack. If you do not properly charge the phone, battery performance will be compromised. 4. Put the battery compartment door back on. Red wire Black wire 5 PoMMeS LAYOUT AND KEY DEFINITION Base Layout Audio in Audio out Socket USB Power Speaker Speaker Command keys Home screen button On/Off Camera Jog wheel 6 BEFORE YOU BEGIN PARTS CHECKLIST Make sure your package includes the items shown here. • User’s guide • Main unit • Charging cradle • AC/ DC power adaptor • Li-ion Battery • Stylus • Service Tips and T&C sheet IMPORTANT INSTALLATION INFORMATION • Installation of PoMMeS require proper setup of BRM for the connection to your service center, please consult your service hotline for details. • Never install PoMMeS jacks in wet locations unless the jack is specifically designed for wet locations. • Use with care, never drop the main unit to the floor as it would cause hazardous damage to the LCD and the main units. • User has to take care well to the LCD touch screen as LCD will damage if user is improperly using the touch screen. • Never touch non-insulated wires or terminal, unless the line has been disconnected at the network interface. • Use caution when installing or modifying PoMMeS network setting. • Your services center will not be responsible for damages not caused by component defect. IMPORTANT INSTALLATION GUIDELINES • Properly charge up the main unit for 6 hours. Charge LED would change from orange to green. • Install PoMMeS near both BRM. • Avoid sources of noise, such as a window by a busy street, and electrical noise, such motors, microwave ovens, and fluorescent lighting. • Avoid heat sources, such as heating air ducts, heating appliances, radiators, and direct sunlight. • Avoid areas of excessive moisture or extremely low temperature. • Avoid dusty locations. • Avoid other cordless telephones or personal computers. • Choose the best location to install your PoMMeS multimedia device. Your PoMMeS should be placed on a level surface, such as a desk or table top. • Wait approximately 60-90 seconds for LCD to display the standby screen. Start-up and initial configuration of the device is automatic. No action on your part is required. If the standby screen does not appear, or if an error message is displayed, turn AC power off and on again. • If failure to start up persists, contact your service’s 24-hour fault reporting hotline for assistance. 7 SET UP Before using the PoMMeS multi-media device, you need to set up the proper operation conditions. • Please consult your service center hotline for network setup procedure. 8 Appendix 1: Important Safety Instructions 1. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 2. Place on firm stable surface. For optimal performance, avoid placing on metallic or reflective surface. 3. Do not expose to direct sunlight. 4. Do not attempt repairs. Contact your service center’s fault reporting hotline for assistance. 5. Avoid spillage of liquids onto the device. In the event of spillage, contact your service center. 6. To clean the device, wipe with damp cloth. Do not use soap or other cleansers. 7. The battery cover on the rear is an important safety component. Please do not use the product when the cover is not well positioned. Please contact your dealer if the cover is missing. 8. This device can only be used in a distance over 20cm between the bodies and this is not a handheld device. Appendix 2: Troubleshooting 1. Check the item first! a. Make sure power adapter is plugged securely into the power source. b. Make sure DC jack is plugged to the Docking. c. Make sure Main unit is properly charged. 2. Log-on failure? Cannot use Internet TV services? a. Make sure BRM is powered on. b. Make sure connection is properly setup. c. Stay at 1.5 meter distance from the BRM. d. Power off the unit and power ON again. e. If problem persist, call service provider hotline for network setup properly. 3. Speaker is muffled? a. Place unit on flat surface. b. Place unit around 1.5m from the BRM and away from other electronics devices. 4. Slow response? a. Delete on messages and memories and reboot the unit again. 5. No response? a. Reset the unit by unplugging the battery and rep…

Text truncated - open the document above for the full version.

Thomson Inc. 101 West 103rd Street Indianapolis Indiana United States TEL:+1(317)587 4086 FAX:+1(317)587 9522 Date: 2009-12-15 General Declaration FCC ID: G95TWTG001 We, Thomson Inc., declares that the device does not have “Ad Hoc on non-US frequencies” and/or “on DFS frequencies” . If you have any questions regarding the declaration, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------- Michel GROSSIER /Safety & Compliance Thomson Inc. E-mail: [email protected]

Thomson Inc. 101 West 103rd Street Indianapolis Indiana United States TEL:+1(317)587 4086 FAX:+1(317)587 9522 Date:2009-12-15 FCC ID: G95TWTG001 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ___________________________________ Michel GROSSIER / Safety & Compliance Thomson Inc. E-mail: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Docking Page 4

101.00 mm Modelname: Wifi Tablet Date: MM/DD/YY Time: HH/MM/SS Serial Numbers : Q'TY : 5 PCS Carton ID: XXXXX OF XXXXX Part No.:DSLXXXXXXXXXX MADE IN PRC #$%& '( )*+, )*-. /0&1 234 564 78 2008.6.5 POMMES Karen Lo 7332POMMES*0EA1 **Av:**!" Gloria Tang THOMSON **Attention ** Carton Label Remark: 1.LOGO: Black color 2.MAC.S/N.provided by Thomson 3 --- .S/N format refer to P7 DDD:Manufacture Date --- YY: Manufacture Year ---20:S/N version ---UUUUUU:unique part of the serial number ---CC:S/N Checksum 5.Barcode:Code39(barcode height4mm) 6.Font: Arial DYDYD20UUUUUUCC DYDYD20UUUUUUCC DYDYD20UUUUUUCC DYDYD20UUUUUUCC DYDYD20UUUUUUCC #$%& '( )*+, )*-. /0&1 234 564 78 1. CharacterArial bold, font 2. Label dimension: 40*40mm **Attention** ： AV:ETSI!"#$: Label -1 -Product label WiFi Tablet S/N: DYDYD20UUUUUUCC MAC: XXXXXXXXXXXX Designed in France Assembled in China 40.00 m m 40.00 mm 2008.6.5 POMMES Karen Lo 7332POMMES*0EA1 Gloria Tang THOMSON Remark: 1.LOGO: Black color 2.MAC.S/N.provided by Thomson 3 --- .S/N format refer to P7 DDD:Manufacture Date --- YY: Manufacture Year ---20:S/N version ---UUUUUU:unique part of the serial number ---CC:S/N Checksum 5.Barcode:Code39(barcode height4mm) 6.Font: Arial 1.2A15V 0560 FCC ID: G95TWTG001 #$%& '( )*+, )*-. /0&1 234 564 78 1. CharacterArial bold, font 2. Label dimension: 30*20mm **Attention** ： AV:ETSI!"#$: Label -2-Cradle label WiFi Tablet Cradle 20.0 0 m m 30.00 mm 2008.6.5 POMMES Karen Lo 7332POMMES*0EA1 Gloria Tang THOMSON 1.2A15V Designed in France Assembled in China 0560 FCC ID: G95TWTG001 #$%& '( )*+, )*-. /0&1 234 564 78 1. CharacterArial bold, font 2. Label dimension64*28mm **Attention** ： ： AV:ETSI!"#$: White Box label S/N: DYDYD20UUUUUUCC MAC: XXXXXXXXXXXX Designed in France Assembled in China 28.00 m m 64.00 mm WiFi Tablet 2008.6.5 POMMES Karen Lo 7332POMMES*0EA1 Gloria Tang THOMSON Remark: 1.LOGO: Black color 2.MAC.S/N.provided by Thomson 3 --- .S/N format refer to P7 DDD:Manufacture Date --- YY: Manufacture Year ---20:S/N version ---UUUUUU:unique part of the serial number ---CC:S/N Checksum 5.Barcode:Code39(barcode height4mm) 6.Font: Arial #$%& '( )*+, )*-. /0&1 234 564 78 AV:ETSI!"#$: Label -1 -Product label 2008.6.5 POMMES Karen Lo 7332POMMES*0EA1 Gloria Tang THOMSON WiFi Tablet S/N: DYDYD20UUUUUUCC MAC: XXXXXXXXXXXX 9V2A Designed in France Assembled in China WiFi Tablet S/N: DYDYD20UUUUUUCC MAC: XXXXXXXXXXXX Designed in France Assembled in China 1.2A15V 0560 FCC ID: G95TWTG001 WiFi Tablet S/N: DYDYD20UUUUUUCC MAC: XXXXXXXXXXXX Designed in France Assembled in China 1.2A15V 0560 FCC ID: G95TWTG001 #$%& '( )*+, )*-. /0&1 234 564 78 AV:ETSI!"#$: Label -2-Cradle label 2008.6.5 POMMES Karen Lo 7332POMMES*0EA1 Gloria Tang THOMSON W i F i Ta b le t C r a d l e 1 .2 A 1 5 V Designed in France Assembled in China 0 5 6 0 F C C I D : G 95T W T G 001 WiFi Tablet Cradle 1.2A15V Designed in France Assembled in China 0560 FCC ID: G95TWTG001 !" #$%& '( )*+, )*-. /0&1 234 564 78 Av%!" 2008.6.5 POMMES Karen Lo 7332POMMES*0EA1 Gloria Tang THOMSON

FCC ID .: G95TWTG001 Label Location

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Docking

FCC ID: G95TWTG001 Report No.: RF980812L01 OPERATIONAL DESCRIPTION This device is a WiFi Photo Frame, which operates in the 2.4GHz frequency spectrum with throughput of up to 54Mbps which OFDM technique will be applied. If the signal to noise ratio is too poor which could not support 54Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by AC adapter or battery. The antennas are Wire antenna and Printed antenna without antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No.: SA980812L01-1 1 Report Format Version 3.0.1 SAR TEST REPORT REPORT NO.: SA980812L01-1 MODEL NO.: PoMMeS RECEIVED: Aug. 12, 2009 TESTED: Jan. 06, 2010 ISSUED: Jan. 08, 2010 APPLICANT: Thomson Inc ADDRESS: 101 West 103rd Street, Indianapolis, Indiana 46290, United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch AB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 34 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: SA980812L01-1 2 Report Format Version 3.0.1 TABLE OF CONTENTS 1. CERTIFICATION................................................................................................................3 2. GENERAL INFORMATION.................................................................................................4 2.1 GENERAL DESCRIPTION OF EUT...................................................................................4 2.2 GENERAL DESCRIPTION OF APPLIED STANDARDS.....................................................5 2.3 GENERAL INOFRMATION OF THE SAR SYSTEM...........................................................6 2.4 TEST EQUIPMENT............................................................................................................9 2.5 GENERAL DESCRIPTION OF THE SPATIAL PEAK SAR EVALUATION.........................10 3. DESCRIPTION OF SUPPORT UNITS.............................................................................13 4. DESCRIPTION OF TEST MODES AND CONFIGURATIONS..........................................14 4.1. DESCRIPTION OF TEST CONDITION............................................................................14 4.2. ENHANCED ENERGY COUPLING AT INCREASED SEPARATION DISTANCES..........14 4.3. DESCRIPTION OF TEST MODE.....................................................................................15 4.4. SUMMARY OF TEST RESULTS......................................................................................16 5. TEST RESULTS...............................................................................................................17 5.1 TEST PROCEDURES......................................................................................................17 5.2 SAR LIMITS.....................................................................................................................18 5.3 MEASURED SAR RESULTS...........................................................................................19 5.4 RECIPES FOR TISSUE SIMULATING LIQUIDS..............................................................20 6. SYSTEM VALIDATION.....................................................................................................23 6.1 TEST PROCEDURE........................................................................................................23 6.2 VALIDATION RESULTS...................................................................................................25 6.3 SYSTEM VALIDATION UNCERTAINTIES........................................................................26 7. MEASUREMENT SAR PROCEDURE UNCERTAINTIES................................................27 7.1. PROBE CALIBRATION UNCERTAINTY..........................................................................27 7.2. ISOTROPY UNCERTAINTY............................................................................................28 7.3. BOUNDARY EFFECT UNCERTAINTY............................................................................28 7.4. PROBE LINEARITY UNCERTAINTY...............................................................................29 7.5. READOUT ELECTRONICS UNCERTAINTY...................................................................29 7.6. RESPONSE TIME UNCERTAINTY..................................................................................29 7.7. INTEGRATION TIME UNCERTAINTY.............................................................................30 7.8. PROBE POSITIONER MECHANICAL TOLERANCE.......................................................31 7.9. PROBE POSITIONING....................................................................................................31 7.10. PHANTOM UNCERTAINTY.............................................................................................32 7.11. DASY5 UNCERTAINTY BUDGET...................................................................................33 8. INFORMATION ON THE TESTING LABORATORIES......................................................34 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION Report No.: SA980812L01-1 3 Report Format Version 3.0.1 1. CERTIFICATION PRODUCT: WiFi Photo Frame MODEL: PoMMeS BRAND: THOMSON APPLICANT: Thomson Inc TESTED: Jan. 06, 2010 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) RSS-102 The above equipment (model: PoMMeS) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Jan. 08, 2010 Joanna Wang / Senior Specialist TECHNICAL ACCEPTANCE : , DATE : Jan. 08, 2010 Responsible for …

Text truncated - open the document above for the full version.

D2: DOSIMETRIC E-FIELD PROBE D3: DAE

D4: SYSTEM VALIDATION DIPOLE

Report No.: RF980812L01 1 Report Format Version 3.0.0 FCC TEST REPORT REPORT NO.: RF980812L01 MODEL NO.: PoMMeS RECEIVED: Aug. 12, 2009 TESTED: Aug. 12 ~ Oct. 27, 2009 ISSUED: Oct. 29, 2009 APPLICANT: Thomson Inc ADDRESS: 101 West 103rd Street, Indianapolis, Indiana 46290, United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 58 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF980812L01 2 Report Format Version 3.0.0 TABLE OF CONTENTS 1. CERTIFICATION ......................................................................................................... 4 2. SUMMARY OF TEST RESULTS................................................................................. 5 2.1 MEASUREMENT UNCERTAINTY .............................................................................. 5 3. GENERAL INFORMATION ......................................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT............................................................................ 6 3.2 DESCRIPTION OF TEST MODES.............................................................................. 7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST......................................................... 7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL.............................. 8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................... 10 3.4 DESCRIPTION OF SUPPORT UNITS...................................................................... 10 4. TEST TYPES AND RESULTS ................................................................................... 10 4.1 RADIATED EMISSION MEASUREMENT ................................................................. 10 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT .............................................. 10 4.1.2 TEST INSTRUMENTS .............................................................................................. 12 4.1.3 TEST PROCEDURES ............................................................................................... 13 4.1.4 DEVIATION FROM TEST STANDARD ..................................................................... 13 4.1.5 TEST SETUP ............................................................................................................ 14 4.1.6 EUT OPERATING CONDITIONS.............................................................................. 14 4.1.7 TEST RESULTS ........................................................................................................ 15 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................ 29 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ......................................... 29 4.2.2 TEST INSTRUMENTS .............................................................................................. 29 4.2.3 TEST PROCEDURES ............................................................................................... 30 4.2.4 DEVIATION FROM TEST STANDARD ..................................................................... 30 4.2.5 TEST SETUP ............................................................................................................ 31 4.2.6 EUT OPERATING CONDITIONS.............................................................................. 31 4.2.7 TEST RESULTS ........................................................................................................ 32 4.3 6dB BANDWIDTH MEASUREMENT ........................................................................ 36 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT...................................................... 36 4.3.2 TEST INSTRUMENTS .............................................................................................. 36 4.3.3 TEST PROCEDURE ................................................................................................. 36 4.3.4 DEVIATION FROM TEST STANDARD ..................................................................... 36 4.3.5 TEST SETUP ............................................................................................................ 37 4.3.6 EUT OPERATING CONDITIONS.............................................................................. 37 4.3.7 TEST RESULTS ........................................................................................................ 38 4.4 MAXIMUM OUTPUT POWER................................................................................... 40 4.4.1 LIMITS OF MAXIMUM OUTPUT POWER MEASUREMENT ................................... 40 4.4.2 INSTRUMENTS ........................................................................................................ 40 4.4.3 TEST PROCEDURES ............................................................................................... 40 4.4.4 DEVIATION FROM TEST STANDARD ..................................................................... 40 4.4.5 TEST SETUP ............................................................................................................ 41 4.4.6 EUT OPERATING CONDITIONS.............................................................................. 41 4.4.7 TEST RESULTS ........................................................................................................ 42 4.5 POWER SPECTRAL DENSITY MEASUREMENT ................................................... 43 4.5.1 LIMITS OF POWER SPECTRAL DENS…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST

1 PHOTOGRAPHS OF THE TEST CONFIGURATION BODY POSITION TIP BOTTOM TEST SETUP PHOTO 2 DESCRIPTION OF ANTENNA LOCATION: