GU69460IPLA41372.4GHz Wireless Printer w/ Internal DSSS LAN

TC9460IPAD Rev. AA 7/02 2002 Paxar Corporation. All rights reserved. MONARCH is a registered trademark of Monarch Marking Systems, Inc. Sierra Sport and 9460 are trademarks of Monarch Marking Systems, Inc. Paxar is a trademark of Paxar Corporation. CONFIGURING YOUR IP PRINTER Use these instructions to configure the radio inside your MONARCH Sierra Sport  2 IP Printer. The IP printer operates on any WiFi (Wireless Fidelity) compatible 802.11b RF network. Make sure your access point and network are correctly set up. Refer to your network manuals for more information. This manual does not include information about setting up your RF network. Refer to the printer’s Quick Reference for information about loading supplies, etc. Installing the Configuration Utility Download the Configuration Utility from our Web site (www.monarch.com/service/service_utilities.htm). This utility supports the following platforms: Microsoft  Windows 98/2000/ME and Windows NT (SP3+). If using WinPCap version 2.3 or greater, Microsoft Windows XP and 95 are supported. Follow the instructions provided. Read readme.txt for updates and more information. After installing the Configuration Utility, you can set up the printer using a serial cable or by using your network. For initial printer setup, you must use the serial interface. About the Configuration Utility This utility allows you to easily configure your IP printer. 1. Start the Configuration Utility. 2. Click Features List to see a list of supported radios. 3. Click Ok when finished. 4. Click About/Disclaimer to see the version number of the Utility. 5. Click Ok when finished. 6. Click Exit to exit the Utility. 2 Selecting the Printer Using a Serial Interface Before you can use the IP printer, you must configure it. All nodes of a wireless network need to have the same settings in order to communicate with each other. For initial printer setup, you must use the serial interface. 1. Connect a serial cable (DB9 female to DB9 female all lines wired straight through) from the host or PC to the printer’s radio harness. 2. Turn on the printer. 3. Start the Configuration Utility. Depending on the Configuration Utility’s version, the screens may appear differently. 4. Select Serial, direct to card. Radio Harness 3 5. Click Configure Interface. 6. Make sure you select the correct communication port and 19.2 Baud Rate (19.2 is the only supported baud rate). 7. Click Ok. 8. Click Discover. Since you are connected through a serial interface, only one printer appears. The Card History Window appears at the bottom of the screen to give a status of the connected printers. For example, you may see a message “Card Discovered” when an IP printer is discovered by the Configuration Utility. Messages also appear when printers are turned off or disconnected from the network. You can highlight a printer and Clear Current Card’s History or Clear All Card Histories. 4 9. Highlight the printer to configure and click Config. A CAUTION window appears. Read all the information. You can disable the CAUTION window for this session or permanently. Click Ok to continue. 10. Follow the steps in “Configuring the RF Interface.” Selecting the Printer Using a Network Interface Follow these steps to select a printer using a network interface or to verify printers on a network. 1. Turn on the printer. 2. Start the Configuration Utility. 3. Select Network. 4. Click Discover. Since you are connected through a network interface, multiple printers may appear. The Card History Window appears at the bottom of the screen to give a status of the connected printers. For example, you may see a message “Card Discovered” when an IP printer is discovered by the Configuration Utility. Messages also appear when printers are turned off or disconnected from the network. You can highlight a printer and Clear Current Card’s History or Clear All Card Histories. 5 5. If necessary, click Configure Interface to check the network devices available on the host. 6. Make any changes and click Ok when finished or click Cancel to exit without saving any changes. You return to the Main screen. 7. Highlight the printer you want to configure and click Config. A CAUTION window appears. Read all the information. You can disable the CAUTION window for this session or permanently. Click Ok to continue. 8. Follow the steps in “Configuring the RF Interface.” 6 Configuring the RF Interface Setting a Name and ESS ID 1. Enter a Unit Name. Use a meaningful name, for example, WHSEFLR. 2. Enter the 802.11b ESS ID. NOTE: The ESS ID address is case-sensitive. 3. Enter a valid address for the Remote IP (even if you are not using the remote IP). Setting the Protocol for Listen Mode Listen mode waits for a host to connect to the specified port and receives data. Listen mode can be used with TCP (select port number) or LPD (no need to specify port) protocols. 1. Select the Protocol as TCP or LPD. Do not use UDP. 2. Select the Connection Mode as Listen. 3. Select the Port. Setting the Protocol for Call Remote Mode Call remote mode initiates the data transfer. Call remote can be used for TCP (select port number) or Telnet (no need to specify port) protocols. 1. Select the Protocol as TCP or Telnet from the Card Configuration screen. Do not use UDP. 2. Select the Connection Mode as Call Remote. 3. Specify the Remote IP Address. 4. Select the Port. 5. Enter the amount of Retries in milliseconds after a failure before a connection is tried again. 7 Setting the Power Save Mode 1. Select the Power Save mode by checking the Enable box from the Card Configuration screen. 2. Set the Algorithm to a value between 1 and 10. 1 is the shortest sleep time (uses battery power quicker, but responds faster); 10 is the longest sleep time (optimal battery conservation, but responds slower). If the Power Save mode is not enabled, the device operates in CAM mode (constantly awake). CAM means the printer is continuously receiving and transmitting data. This mode uses b…

Text truncated - open the document above for the full version.

Symbol Technologies, Inc. 5 August 2002 Jim Bacher PAXAR Corporation 170 Monarch Lane Miamisburg, OH 45342 RE: Authorization for PAXAR Corporation to apply for Regulatory Approvals for PAXAR products that include the Symbol Technologies Inc. radio card Model number CC-4137-1000- WW. Dear Mr. Bacher, This letter grants authorization for PAXAR to apply for Regulatory Approvals for PAXAR products that include the Symbol Technologies Inc. radio card: Model number CC-4137-1000-WW This letter grants authorization for PAXAR to apply to the Federal Communications Commission, Industry Canada, and other International Regulatory Agencies for a Grant under PAXAR’s Grantee Code or the equivalent, for PAXAR products that include the Symbol Technologies Inc. radio card: Model number CC-4137-1000-WW This letter grants authorization for PAXAR to pursue Test Reports that are for the single purpose of gaining International Regulatory Approvals for PAXAR products that include the Symbol Technologies Inc. radio card: Model number CC-4137-1000-WW No other changes or modifications are authorized; all of Symbol Technologies Inc. Regulatory Approvals for the radio card Model number CC-4137-1000-WW are to remain in effect and on file. This letter of authorization to remain in effect until notified or 3 years, which ever comes first. Respectfully Marks S. Luksich Senior Manager, Regulatory Symbol Technologies Inc. SYMBOL TECHNOLOGIES INC. One Symbol Plaza. (561) 487-1718 . Fax (561) 483-3922

October 31, 2002 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Attention: Martin Perrine In re: Monarch Marking Systems, Inc. FCC ID: GU69460IPLA4137 731 Confirmation No.: TC200548 Request for Tech. Info.: 11/04/2002 Correspondence Number: 5693 Dear Martin: Transmitted herewith, on behalf of Monarch Marking Systems, Inc., is an amendment provided in response to the request for technical information dated October 2, 2002 (FCC ID: GU69460IPL4137 TC737391 CRN: 5332 - incorrect FCC ID). 1. Under the correct FCC ID above, the FCC ID on the label is consistent. 2. Please find attached the EMC report data sheets showing the detector bandwidth. 3. Please find attached the EMC report data sheets showing the peak conducted power, power spectral density, and the conducted spurious emission data. 4. Please find attached the EMC report data sheets showing the band edge compliance data. 5. Please find attached the EMC report data sheet showing the bandwidth measurement data. 6. The EUT was controlled using the manufacturer’s software codes set at maximum power. 7. The EMC test report and the revised SAR report show the correct tested frequencies of 2412, 2437 and 2462 MHz. 8. The device will be typically held by hand. The device was tested in both the LCD side and the printer side (in touch mode) and shows compliance with FCC RF exposure requirements. Please find attached the picture of the device. If you have any further questions, please do not hesitate to contact us. Cc: Monarch Marking Systems, Inc.

December 17, 2002 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Attention: Martin Perrine In re: Monarch Marking Systems, Inc. FCC ID: GU69460IPLA4137 731 Confirmation No.: TC200548 Request for Tech. Info.: 12/06/2002 Correspondence Number: 6104 Dear Martin: Transmitted herewith, on behalf of Monarch Marking Systems, Inc., is an amendment provided in response to the request for technical information dated December 6, 2002 (FCC ID: GU69460IPLA4137 TC200548 CRN: 6104 — Technical Information). 1. Please find the attached revised sample label that complies with Part 15.19 (a)(3). 2. Conducted power measurements were taken with a peak power meter and the results are attached. Spectrum analyzer plots are also submitted (for reference only because of bandwidth limitations). 3. Conducted power spectral density measurements are attached. 4. Please find the attached band edge plots. If you have any further questions, please do not hesitate to contact us. Cc: Monarch Marking Systems, Inc.

© 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP

Page 1 of 1 11/1/02file://C:\WINDOWS\Desktop\9460pr.jpg

© 2002PCTEST Lab SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. (SEE NEXT PAGE)

© 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP

2450MHz Brain Dipole Validation SAM Phantom; Flat Section; Probe:ET3DV6 - SN1677; ConvF(4.40,4.40,4.40) Med. Parameters 2450MHz Brain: σ = 1.79 mho/m ε r = 40.1 ρ = 1.00 g/cm 3 ; Antenna Position -- Out; Crest Factor 1.0 SAR (1g): 13.0 mW/g, SAR (10g): 7.60 mW/g 2450MHz Brain Dipole Validation (D-2450S, S/N: 105 ) Frequency: 2450MHz; Antenna Input Power: 250 [mW]; Ambient Temp. = 22.3°C / Meas. Tissue Temp. = 22.2°C PCTEST Brain Tissue Simulating Liquid [05/21/2002] SAR Tot [mW/g] 9.87E-1 3.84E+0 6.40E+0 8.98E+0 1.14E+1 PCTEST Engineering Laboratory, Inc.

PCTEST ENGINEERING LABORATORY, INC. 6660 — B Dobbin Road • Columbia, MD 21045 • USA Telephone 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com (email: [email protected]) CERTIFICATE OF COMPLIANCE (SAR EVALUATION) PCTEST SAR REPORT FCC CERTIFICATION Reviewed by: Quality Manager SAR Filename: SAR-220520310.GU6 Test Dates: May 21, 2002 Equipment Type: Wireless Printer FCC ID: GU69460IPLA4137 Page 1 of 22 © 2002 PCTEST Engineering Laboratory, Inc APPLICANT NAME & ADDRESS: DATE & LOCATION OF TESTING: Monarch Marking Systems Inc. Dates of Tests: May 21, 2002 170 Monarch Lane Test Report S/N: SAR.220520310.GU6 Miamisburg, Ohio 45342 Test Site: PCTEST Lab, Columbia, MD USA Attn: James A. Bacher, Senior Engineer FCC ID: GU69460IPLA4137 APPLICANT: MONARCH MARKING SYSTEMS, INC. EUT Type: 2.4 GHz Wireless Printer (DSSS) Tx Frequency: 2402 — 2480 MHz Rx Frequency: 2402 — 2480 MHz Max. RF Output Power: 23 mW Max. SAR Measurement: 0.0132W/kg Body SAR; Trade Name/Model(s): PAXAR Model: 9460IP W/ Symbol PCMCIA Card Model: #LA-4137 FCC Classification: Part 15 Spread Spectrum Transmitter (DSSS) FCC Rule Part(s): §2.1093; ET Docket 96.326 Application Type: Certification Test Device Serial No.: identical prototype This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE Std. 1528-200X (Draft 6.4, July 2001). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. 220520310.GU6 PCTEST SAR REPORT FCC CERTIFICATION Reviewed by: Quality Manager SAR Filename: SAR-220520310.GU6 Test Dates: May 21, 2002 Equipment Type: Wireless Printer FCC ID: GU69460IPLA4137 Page 2 of 22 © 2002 PCTEST Engineering Laboratory, Inc 1. INTRODUCTION .................................................................................................. 3 SAR DEFINITION ................................................................................................. 3 2. SAR MEASUREMENT SETUP .................................................................................. 4 Robotic System ....................................................................................................... 4 System Hardware ................................................................................................... 4 System Electronics .................................................................................................. 4 3. DASY3 E-FIELD PROBE SYSTEM ............................................................................ 5 Probe Measurement System.................................................................................... 5 Probe Specifications ............................................................................................... 5 4. Probe Calibration Process....................................................................................... 6 Dosimetric Assessment Procedure .......................................................................... 6 Free Space Assessment ........................................................................................... 6 Temperature Assessment ........................................................................................ 6 5. PHANTOM & EQUIVALENT TISSUES .................................................................... 7 SAM Phantom ........................................................................................................ 7 Brain & Muscle Simulating Mixture Characterization ............................................. 7 Device Holder for Transmitters............................................................................... 7 6. TEST SYSTEM SPECIFICATIONS ............................................................................. 8 Automated Test System Specifications .................................................................... 8 7. DOSIMETRIC ASSESSMENT & PHANTOM SPECS................................................. 9 Measurement Procedure......................................................................................... 9 Specific Anthropomorphic Mannequin (SAM) Specifications.................................. 9 8. DEFINITION OF REFERENCE POINTS ................................................................. 10 EAR Reference Point............................................................................................. 10 Handset Reference Points ..................................................................................... 10 9. TEST CONFIGURATION POSITIONS .................................................................. 11 Positioning for Cheek/Touch ................................................................................ 11 Positioning for Ear / 15° Tilt .................................................................................. 12 Body Holster /Belt Clip Configurations ................................................................. 13 10. ANSI/IEEE C95.1 - 1992 RF EXPOSURE LIMITS ................................................... 14 Uncontrolled Environment ................................................................................... 14 Controlled Environment........................................................................................ 14 11. MEASUREMENT UNCERTAINTIES ....................................................................... 15 SAR Measurement Unc…

Text truncated - open the document above for the full version.

MONARCH Model: 9460IP -- 2.4GHz Body SAR SAM Phantom; Flat Section; Probe:ET3DV6 - SN1677; ConvF(4.00,4.00,4.00) Med. Parameters 2450 MHz Muscle: σ = 1.98 mho/m ε r = 52.2 ρ = 1.00 g/cm 3 ; Antenna Position -- Out; Crest Factor 1.0 SAR (1g): 0.0120 mW/g, SAR (10g): 0.0042 mW/g Monarch 2.4GHz DSSS Wireless Printer Model: 9460IP Low Channel, 2412MHz [CW Mode]; Standard Battery; Ambient Temp. = 22.2°C / Meas. Tissue Temp. = 22.1°C Conducted Power = 23mW; Spacing = Touch LCD side of EUT to flat phantom, No Holster/No BeltClip Test Date -- 05/21/2002 [FCC/OET Bulletin 65 - Supplement C, July 2001] SAR Tot [mW/g] 9.00E-4 2.70E-3 4.50E-3 6.30E-3 8.10E-3 PCTEST Engineering Laboratory, Inc. MONARCH Model: 9460IP -- 2.4GHz Body SAR SAM Phantom; Flat Section; Probe:ET3DV6 - SN1677; ConvF(4.00,4.00,4.00) Med. Parameters 2450 MHz Muscle: σ = 1.98 mho/m ε r = 52.2 ρ = 1.00 g/cm 3 ; Antenna Position -- Out; Crest Factor 1.0 SAR (1g): 0.0132 mW/g, SAR (10g): 0.0047 mW/g Monarch 2.4GHz DSSS Wireless Printer Model: 9460IP Mid Channel, 2437MHz [CW Mode]; Standard Battery; Ambient Temp. = 22.2°C / Meas. Tissue Temp. = 22.1°C Conducted Power = 23mW; Spacing = Touch LCD side of EUT to flat phantom, No Holster/No BeltClip Test Date -- 05/21/2002 [FCC/OET Bulletin 65 - Supplement C, July 2001] SAR Tot [mW/g] 1.10E-3 3.30E-3 5.50E-3 7.70E-3 9.90E-3 PCTEST Engineering Laboratory, Inc. MONARCH Model: 9460IP -- 2.4GHz Body SAR SAM Phantom; Flat Section; Probe:ET3DV6 - SN1677; ConvF(4.00,4.00,4.00) Med. Parameters 2450 MHz Muscle: σ = 1.98 mho/m ε r = 52.2 ρ = 1.00 g/cm 3 ; Antenna Position -- Out; Crest Factor 1.0 SAR (1g): 0.0131 mW/g, SAR (10g): 0.0042 mW/g Monarch 2.4GHz DSSS Wireless Printer Model: 9460IP High Channel, 2462MHz [CW Mode]; Standard Battery; Ambient Temp. = 22.2°C / Meas. Tissue Temp. = 22.1°C Conducted Power = 23mW; Spacing = Touch LCD side of EUT to flat phantom, No Holster/No BeltClip Test Date -- 05/21/2002 [FCC/OET Bulletin 65 - Supplement C, July 2001] SAR Tot [mW/g] 1.10E-3 3.30E-3 5.50E-3 7.70E-3 9.90E-3 PCTEST Engineering Laboratory, Inc. MONARCH Model: 9460IP -- 2.4GHz Body SAR SAM Phantom; Flat Section; Probe:ET3DV6 - SN1677; ConvF(4.00,4.00,4.00) Med. Parameters 2450 MHz Muscle: σ = 1.98 mho/m ε r = 52.2 ρ = 1.00 g/cm 3 ; Antenna Position -- Out; Crest Factor 1.0 SAR (1g): 0.0008 mW/g, SAR (10g): -0.00 mW/g Monarch 2.4GHz DSSS Wireless Printer Model: 9460IP Low Channel, 2412MHz [CW Mode]; Standard Battery; Ambient Temp. = 22.2°C / Meas. Tissue Temp. = 22.1°C Conducted Power = 23mW; Spacing = Touch printer side of EUT to flat phantom, No Holster/No BeltClip Test Date -- 05/21/2002 [FCC/OET Bulletin 65 - Supplement C, July 2001] SAR Tot [mW/g] 1.00E-4 3.00E-4 5.00E-4 7.00E-4 9.00E-4 PCTEST Engineering Laboratory, Inc. MONARCH Model: 9460IP -- 2.4GHz Body SAR SAM Phantom; Flat Section; Probe:ET3DV6 - SN1677; ConvF(4.00,4.00,4.00) Med. Parameters 2450 MHz Muscle: σ = 1.98 mho/m ε r = 52.2 ρ = 1.00 g/cm 3 ; Antenna Position -- Out; Crest Factor 1.0 SAR (1g): 0.0011 mW/g, SAR (10g): 0.0000 mW/g Monarch 2.4GHz DSSS Wireless Printer Model: 9460IP Mid Channel, 2437MHz [CW Mode]; Standard Battery; Ambient Temp. = 22.2°C / Meas. Tissue Temp. = 22.1°C Conducted Power = 23mW; Spacing = Touch printer side of EUT to flat phantom, No Holster/No BeltClip Test Date -- 05/21/2002 [FCC/OET Bulletin 65 - Supplement C, July 2001] SAR Tot [mW/g] 1.00E-4 3.00E-4 5.00E-4 7.00E-4 9.00E-4 PCTEST Engineering Laboratory, Inc. MONARCH Model: 9460IP -- 2.4GHz Body SAR SAM Phantom; Flat Section; Probe:ET3DV6 - SN1677; ConvF(4.00,4.00,4.00) Med. Parameters 2450 MHz Muscle: σ = 1.98 mho/m ε r = 52.2 ρ = 1.00 g/cm 3 ; Antenna Position -- Out; Crest Factor 1.0 SAR (1g): 0.0013 mW/g, SAR (10g): 0.0002 mW/g Monarch 2.4GHz DSSS Wireless Printer Model: 9460IP High Channel, 2462MHz [CW Mode]; Standard Battery; Ambient Temp. = 22.2°C / Meas. Tissue Temp. = 22.1°C Conducted Power = 23mW; Spacing = Touch printer side of EUT to flat phantom, No Holster/No BeltClip Test Date -- 05/21/2002 [FCC/OET Bulletin 65 - Supplement C, July 2001] SAR Tot [mW/g] 1.00E-4 3.00E-4 5.00E-4 7.00E-4 9.00E-4 PCTEST Engineering Laboratory, Inc.

© 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP © 2002 PCTEST Lab MONARCH FCC ID: GU69460IPLA4137 2.4 GHz Wireless Printer (FHSS) Model: PAXAR 9460IP

PCTEST ENGINEERING LABORATORY, INC. 6660 — B Dobbin Road • Columbia, MD 21045 • USA Telephone 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com (email: [email protected]) CERTIFICATE OF COMPLIANCE (SAR EVALUATION) PCTEST SAR REPORT FCC CERTIFICATION Reviewed by: Quality Manager SAR Filename: SAR-220520310.GU6 Test Dates: May 21, 2002 Equipment Type: Wireless Printer FCC ID: GU69460IPLA4137 Page 1 of 22 © 2002 PCTEST Engineering Laboratory, Inc APPLICANT NAME & ADDRESS: DATE & LOCATION OF TESTING: Monarch Marking Systems Inc. Dates of Tests: May 21, 2002 170 Monarch Lane Test Report S/N: SAR.220520310.GU6 Miamisburg, Ohio 45342 Test Site: PCTEST Lab, Columbia, MD USA Attn: James A. Bacher, Senior Engineer FCC ID: GU69460IPLA4137 APPLICANT: MONARCH MARKING SYSTEMS, INC. EUT Type: 2.4 GHz Wireless Printer (DSSS) Tx Frequency: 2412 — 2462 MHz Rx Frequency: 2412 — 2462 MHz Max. RF Output Power: 23 mW Max. SAR Measurement: 0.0132W/kg Body SAR; Trade Name/Model(s): PAXAR Model: 9460IP W/ Symbol PCMCIA Card Model: #LA-4137 FCC Classification: Part 15 Spread Spectrum Transmitter (DSSS) FCC Rule Part(s): §2.1093; ET Docket 96.326 Application Type: Certification Test Device Serial No.: identical prototype This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE Std. 1528-200X (Draft 6.4, July 2001). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. 220520310.GU6 PCTEST SAR REPORT FCC CERTIFICATION Reviewed by: Quality Manager SAR Filename: SAR-220520310.GU6 Test Dates: May 21, 2002 Equipment Type: Wireless Printer FCC ID: GU69460IPLA4137 Page 2 of 22 © 2002 PCTEST Engineering Laboratory, Inc 1. INTRODUCTION .................................................................................................. 3 SAR DEFINITION ................................................................................................. 3 2. SAR MEASUREMENT SETUP .................................................................................. 4 Robotic System ....................................................................................................... 4 System Hardware ................................................................................................... 4 System Electronics .................................................................................................. 4 3. DASY3 E-FIELD PROBE SYSTEM ............................................................................ 5 Probe Measurement System.................................................................................... 5 Probe Specifications ............................................................................................... 5 4. Probe Calibration Process....................................................................................... 6 Dosimetric Assessment Procedure .......................................................................... 6 Free Space Assessment ........................................................................................... 6 Temperature Assessment ........................................................................................ 6 5. PHANTOM & EQUIVALENT TISSUES .................................................................... 7 SAM Phantom ........................................................................................................ 7 Brain & Muscle Simulating Mixture Characterization ............................................. 7 Device Holder for Transmitters............................................................................... 7 6. TEST SYSTEM SPECIFICATIONS ............................................................................. 8 Automated Test System Specifications .................................................................... 8 7. DOSIMETRIC ASSESSMENT & PHANTOM SPECS................................................. 9 Measurement Procedure......................................................................................... 9 Specific Anthropomorphic Mannequin (SAM) Specifications.................................. 9 8. DEFINITION OF REFERENCE POINTS ................................................................. 10 EAR Reference Point............................................................................................. 10 Handset Reference Points ..................................................................................... 10 9. TEST CONFIGURATION POSITIONS .................................................................. 11 Positioning for Cheek/Touch ................................................................................ 11 Positioning for Ear / 15° Tilt .................................................................................. 12 Body Holster /Belt Clip Configurations ................................................................. 13 10. ANSI/IEEE C95.1 - 1992 RF EXPOSURE LIMITS ................................................... 14 Uncontrolled Environment ................................................................................... 14 Controlled Environment........................................................................................ 14 11. MEASUREMENT UNCERTAINTIES ....................................................................... 15 SAR Measurement Unc…

Text truncated - open the document above for the full version.

PCTEST PT. 15.247 REPORT EVALUATION REPORT Reviewed By: Quality Manager Test Report S/N: 15.220520554.GU6 Test Dates: MAY 21, 2002 EUT Type: WIRELESS PRINTER (DSSS) FCC ID: GU69460IPLA4137 Page 1 of 28 PCTEST Engineering Laboratory, Inc. 6660-B Dobbin Road • Columbia, MD 21045 • U.S.A. TEL (410) 290-6652 • FAX (410) 290-6654 http://www.pctestlab.com CERTIFICATE OF COMPLIANCE Monarch Marketing Systems Inc. Dates of Tests: May 21, 2002 170 Monarch Lane Test Report S/N: 15.220730554.GU6 Miamisburg, Ohio 45342 Test Site: PCTEST Lab, Columbia MD Attn: James A. Bacher, Senior Engineer FCC ID GU69460IPLA4137 APPLICANT Monarch Marketing Systems Inc. FCC Rule Part(s): § 15.247; ANSI C-63.4 (1992) Classification: Spread Spectrum Transceiver (DSSS) Max Output Power: 0.022757W Conducted Method/System: Direct Sequence System (DSSS) Equipment Type: 2.4 GHz Wireless Printer (DSSS) Frequency Range: 2412 — 2462 MHz Model No(s).: 9460IP This equipment…

Text truncated - open the document above for the full version.