GU6WJSX2000RFID Printer Transmitter Module

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 45 of 64 APPENDIX I: MANUAL Please refer to the following pages. Monarch  9855  RFID Printer TC9855RFIDQR Rev. AA 3/04 ©2004 Paxar Americas, Inc. All rights reserved. BETA Each product and program carries a respecti ve written warranty, the only warranty on which the customer can rely. Paxar re serves the right to make changes in the product, the programs, and their availabilit y at any time and without notice. Although Paxar has made every effort to provide complete and accurate information in this manual, Paxar shall not be liable for any omissions or inaccuracies. Any update will be incorporated in a later edition of this manual.  2004 Paxar Americas, Inc. All rights reserv ed. No part of this publication may be reproduced, transmitted, stored in a retr ieval system, or translated into any language in any form by any means, without the prior written permission of Paxar Americas, Inc. WARNING This equipment has been tested and found to comply wi th the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to prov ide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can r adiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful in terference in which case the user will be required to correct the interference at his own expense. CANADIAN D.O.C. WARNING This digital apparatus does not exceed the Class A limits for radio noise em issions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n'ém et pas de bruits radioélectr iques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Réglement sur le brouillage radioélectrique édicte par le mini stère des Communications du Canada. Regulatory Compliance Paxar RF products are designed to be compliant with the rules and regulations in the locations into which they are sold and will be labeled as required. The majority of Paxar RF devices are type approved and do not require the user to obtain license or authorization before using the equipment. Any changes or modifications to Paxar equipment not expressly approved by Paxar could void the user authority to operate the equipment. FCC RF Exposure Guidelines To comply with FCC exposure requirement s, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimu m separation distance of 20 cm from all persons. Declaration of Conformity for RF Exposure: The radio module has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as set fo rth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. Radio Frequency Interference Requirements This device complies with Part 15 of the F CC Rules. Operation is subject to the following two conditions: 1) this device ma y not cause harmful interference, and 2) this device must accept any interfer ence that may cause undesired operations. CAUTION: The Part 15 radio device operates on a non-i nterference basis with other devices operating at this frequency when using the listed antenna. Collocation Statement: This device must not be collocated wi th any other antenna or transmitters. Radio Frequency Interference Requirements - Canada This device complies with RSS 210 of Industr y Canada. Operation is subject to the following two conditions: (1) this device ma y not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus meet s the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe A especte toutes les exigencies du Reglement sur le Materiél Brouilleur du Canada. Trademarks Monarch  is a registered trademark of Paxar Americas, Inc. 9855 is a trademark of Paxar Americas, Inc. Paxar  is a trademark of Paxar Corporation. Paxar Americas, Inc. 170 Monarch Lane Miamisburg, OH 45342 Visit www.paxar.com for sales, service, supplies, information, and telephone numbers for our locations throughout the world. TOLL FREE: 1-800-543-6650 (U.S.A.) 1-800-363-7525 (Canada) 1 This Quick Reference contains supply loading and general care and maintenance procedures. For more detailed information, the Operator’s Handbook is on the optional Tabletops Documentation CD-ROM or can be downloaded from our Web site. Check the Web site for the latest release/addendum information. Connecting the Cables The power supply automatically switc hes between 115V or 230V. There are no operator settings required. 1. Plug the power cable into the socket. Plug the other end of the cable into a grounded electrical outlet. 2. Connect the communication cable into the appropriate port. Secure the cable with the connecting screws (serial) or spring clips (parallel). If you are communicating with the host through the serial port, make sure the printer's communication values match those at the host. The factory default values are 9600 Baud, 8 bit data frame, 1 stop bit, no parity, and DTR flow control. Set the communication values on the printer to match those at the host. The printer also has a USB (Universal Serial Bus) Version 1.1 communications port. Drivers are available on our Web site for a variety of operating systems. 3. Turn on the printer. Press ( I ) to turn on and ( O ) to turn off the printer…

Text truncated - open the document above for the full version.

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 38 of 64 APPENDIX B: ATTESTATION – DA 00-1407 MODULAR APPROVAL Please refer to the following page. Paxar Americas, Inc. 170 Monarch Lane Miamisburg, OH 45342 800 543-6650 FAX 937-865-2048 March 15, 2004 Reference: DA 00-1407 Released: June 26, 2000 PART 15 UNLICENSED MODULAR TRANSMITTER APPROVAL American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Below are the eight elements a module is required to meet to comply with Part 15, Unlicensed Modular Approval notice, DA 00-1407, Dated June 26, 2000. Also included are my arguments on why our module meets the requirements. 1. The modular transmitter must have its own RF shielding. This is intended to ensure that the module does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with Part 15 limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. a. The Transmitter provided by Watkins Johnson is provided with an enclosure that provides the required shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. a. The inputs are buffered RS232 and the data is processed by a microprocessor in the Watkins Johnson module, thereby eliminating excessive data rates or over modulation. 3. The modular transmitter must have its own power supply regulation. This is intended to ensure that the module will comply with Part 15 requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. a. We provide an I/O board that regulates the supply voltage from 24 volts down to the 6 volts the Watkins Johnson transmitter needs. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). Any antenna used with the module must be approved with the module, either at the time of initial authorization or through a Class II permissive change. The “professional installation” provision of Section 15.203 may not be applied to modules. a. The antenna uses MMCX connectors. In this application the customer will never change the antenna. The reason is, if they change it to a higher gain antenna, they will program more than one tag at a time, which will prevent their RFID tags from working properly. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). a. Paxar tested the RFID module outside of our printer during the tests at Rhein Tech. During the tests it was powered by the printers 24VDC power supply, using the Paxar I/O board to further reduce the supply voltage to 6VDC (see note in item 3 above). 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. a. This module will only be used in Paxar printers and will be under Paxar control. We will include the required external label as well as label the module. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. a. All of the timing is controlled by software in the Watkins Johnson unit and is not adjustabl…

Text truncated - open the document above for the full version.

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 39 of 64 APPENDIX C: AGENCY AUTHORIZATION LETTER Please refer to the following page. Paxar Americas, Inc. 170 Monarch Lane Miamisburg, OH 45342 800 543-6650 FAX 937-865-2048 February 26, 2004 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 Re: Agent Authorization To Whom It May Concern: Paxar Americas, Inc. hereby authorizes Rhein Tech Laboratories, Inc. (RTL), 360 Herndon Parkway, Suite 1400, Herndon, VA 20170 to act as agent. APPLICANT ANTI-DRUG ABUSE CERTIFICATION: In signing this letter, Applicant certifies that, in the case of an individual applicant, he or she is not subject to a denial of federal benefits, that includes: FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a), or, in the case of a non-individual applicant. No party to the application is subject to a denial of federal benefits that includes FCC benefits, pursuant to that section. For the definition of a “party” for these purposes, see 47 CFR 1.2002(b). If you have any questions or concerns, please contact me by email at [email protected]; phone at 1-937-865-2020; or by fax at 1-937-865-2048. Sincerely, James A. Bacher Senior Engineer Paxar Americas, Inc. A division of Paxar Corp. cc: H. Dayton J. Duckett L. Neuhard

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 40 of 64 APPENDIX D: CONFIDENTIALITY REQUEST LETTER Please refer to the following page. Paxar Americas, Inc. 170 Monarch Lane Miamisburg, OH 45342 800 543-6650 FAX 937-865-2048 March 04, 2004 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: The following information is to be held confidential pursuant of 47 CFR Part 0 §0.459 and Section 552(b)(4) of the Freedom of Information Act, because the information provided contains trade secrets and is proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. • Schematics • Technical Product Description • Block Diagram If you have any questions or concerns, please contact me by email at [email protected]; phone at 1-937-865-2020; or by fax at 1-937-865-2048. Sincerely, James A. Bacher Senior Engineer Paxar Americas, Inc. A division of Paxar Corp. cc: H. Dayton J. Duckett L. Neuhard

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 51 of 64 APPENDIX K: EXTERNAL PHOTOGRAPHS PHOTOGRAPH 7: EUT FRONT VIEW Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 52 of 64 PHOTOGRAPH 8: EUT REAR VIEW Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 53 of 64 PHOTOGRAPH 9: EUT WITH BRACKET

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 42 of 64 APPENDIX F: LABEL AND LABEL LOCATION PHOTOGRAPH 1: FCC ID LABEL LOCATION Please see the following page for a sample of the FCC ID label. FCC ID LABEL HERE Paxar Americas, Inc. FCC ID: GU6WJSX2000 IC: 1502A-WJSX2000 Trade Name: ALIENC1915 RFID: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference that may cause undesired operations. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le material broilleur du Canada. 0681 Paxar Americas, Inc. FCC ID: GU67410 IC: 1502A-741001 Trade Name 7410-01 Rlan: XI-325 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference that may cause undesired operations. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le material broilleur du Canada. 0681 VARIABLE FIELD VARIABLE RFID FCC Label Tom Keller AW-09514 Notes: 1- Outline for location on part only. Do not print. Please see part drawing for details. Graphic Number Rev Rev Dwg Size Scale Designer Client Name Date Ref. Number GB Arnold LocSymChangeEn No.DateByChk A B C D 23 6 4 5 7 236 4 5 7 A B C D Paxar Americas, Inc. 170 Monarch Lane Miamisburg, OH 45342 937 865-8025 FAX 937 865-2048 ID Artmaster 1:1 8.5 x 11 D e si g n N otes: 1. Artwork shown represents size and style of finished product only. 2. Artwork does not necessarily reflect manufacturing process and/or tooling requirements. 3. Please refer to product drawing for location on part and color. 4. Dimensions are for reference only. This information is the confidential, restricted, and sole property of Paxar Corporation. It should be used by the recipient only for the purposes benefiting Paxar, and shall not be disclosed, reproduced, or used by others without prior written approval. N oti ce : 2/5/04 ~~1:1 Color Sample~~ pn-124956-05 35mm 25mm R2.5mm This is designed as a make label on Monarch® TuffMark permanent adhesive material. Background- silver Graphics- black

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 54 of 64 APPENDIX L: INTERNAL PHOTOGRAPHS PHOTOGRAPH 10: PRINTER BEFORE EUT INSTALLED Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 55 of 64 PHOTOGRAPH 11: EUT INSTALLED IN PRINTER Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 56 of 64 PHOTOGRAPH 12: EUT INSTALLED IN PRINTER 2 Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 57 of 64 PHOTOGRAPH 13: RFID INTERFACE SIDE 1 Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 58 of 64 PHOTOGRAPH 14: RFID INTERFACE SIDE 2 Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 59 of 64 PHOTOGRAPH 15: ANTENNA LOCATION Antenna Location Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 60 of 64 PHOTOGRAPH 16: ANTENNA CONNECTION LOCATION Antenna Connection Location Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 61 of 64 PHOTOGRAPH 17: ALIEN RFID CARD FRONT VIEW Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 62 of 64 PHOTOGRAPH 18: ALIEN RFID CARD REAR VIEW Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 63 of 64 PHOTOGRAPH 19: ALIEN RFID CARD SIDE 1 Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 64 of 64 PHOTOGRAPH 20: ALIEN RFID CARD SIDE 2

Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 35 of 64 APPENDIX A: RF EXPOSURE COMPLIANCE FCC Rules and Regulations Part 1.1307, 1.1310, 2.1091, 2.1093: 1. General Information: FCCID: GU6WJSX2000 Environment: General Population/Uncontrolled Exposure Device category: Mobile per Part 2.1091 Modulation Type/Mode: FHSS 2. Operating Configurations and Test Conditions: 2.1 Antenna Type(s): Antenna Type Gain (dBi) Numeric Gain Dipole Dipole -12 0.06 Frequency Range Frequency Tolerance (ppm) Emission Designator 902-928 N/A N/A Duty Cycle Calculation: 0.062ms (pulse width) / 100 ms = 0.62 and 10 log (62%) = -2.1 dB Output Power (Worst Case) Time averaging as an inherent property (100 % Duty Cycle) (W) Time averaging as an inherent property (62 % Duty Cycle, -2.1 dB) (W) EIRP 0.002 (2.5 dBm) 0.001 (0.4 dBm) Conducted 0.028 (14.5 dBm) 0.017 (12.4 dBm) 3. MPE Calculation: The maximum distance from the antenna at which MPE is met or exceeded, is calculated from the equation relating field strength E in V/m, transmit power P in Watts, transmit antenna numeric gain G, and separation distance in meters: The Electric field generated for a 1mW/cm 2 exposure (S) is calculated as follows: Z E S 2 = where: S = Power density E = Electric field Z = Impedance. ZSmVE×=)/( 1 mW/cm 2 = 10 W/m 2 Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 36 of 64 The impedance of free space is 337 ohms, where E and H fields are perpendicular. Thus: 37710)/(×=mVE = 61.4 V/m MPE Calculation: The maximum distance, from the antenna at which MPE is met or exceeded, is calculated from the equation relating field strength E in V/m, transmit power P in Watts, transmit antenna numeric gain G, and separation distance in meters above and solving for d below: d GP mVE ×× = 30 )/( and )/( 30 mVE GP d ×× = Power density: 3770 )/( 2 2 E cmmWP d = The limit for general population/uncontrolled exposure environment above 1500MHz is 1 2 /cmmW. SEPARATION DISTANCE: Antenna Gain (-12 dBi) Separation Distance Numeric gain 0.06 Conducted Power (Watt, worst case) (cm) Duty Cycle (%) 0.017 0.3 62 0.028 0.4 100.0 Calculations: 100% duty cycle = 4.61 06.0028.030 4.0 ×× = cm 62% duty cycle = 4.61 06.0017.030 3.0 ×× = cm Where: S= Power density P=Transmitter conducted power in watts G=Numeric gain D=distance to radiation center Fundamental Operating Frequency: 902-928 MHz Measured conducted power: 0.028W (14.5 dBm) Antenna Gain = -12 dBi; Numeric Gain = 0.06 2 4d GP S ×× × = π Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 RFID Module Page 37 of 64 At 100% Duty Cycle (conducted power worst case) S = 28 x 0.06/4 x π x 20 2 = 0.0003 mW/ cm 2 at 20 cm At 62 % Duty Cycle (conducted power worst case) S= 17 x 0.06/4 x π x 20 2 = 0.0002 mW/ cm 2 at 20 cm Antenna Gain = -12 dBi Conducted Power (mW) = 28 Separation Distance Power Density Limit Calculated Power density at 20 cm distance 1 mW/cm 2 0.0003 mW/ cm 2 C ONCLUSION: The device complies with the MPE requirements by providing a safe separation distance between the antenna, including any radiating structure, and any persons. Proposed RF exposure safety information to include in User’s Manual: CAUTION: Antenna Installation Requirement The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Engineering and Testing for EMC and Safety Compliance 360 Herndon Parkway, Suite 1400 Herndon, VA 20170 Phone: 703-689-0368; Fax: 703-689-2056; Metro: 703-471-6441 CERTIFICATION APPLICATION REPORT FCC PART 15.247 CERTIFICATION Test Lab: Rhein Tech Laboratories, Inc. Phone: 703-689-0368 360 Herndon Parkway Fax: 703-689-2056 Suite 1400 Web Site: www.rheintech.com Herndon, VA 20170 E-Mail: [email protected] Applicant Information: Paxar Americas, Inc. Phone: 937-865-2123 x2020 170 Monarch Lane Fax: 937-865-2048 Miamisburg, OH 45342 Email: [email protected] Contact: James A. Bacher FCC ID: GU6WJSX2000 GRANTEE FRN NUMBER: 0003583150 PLAT FORM: N/A RTL WORK ORDER NUMBER: 2004024 MODEL: AlienC1915 RTL QUOTE NUMBER: QRTL04-214 DATE OF TEST REPORT: March 26, 2004 American National Standard Institute: ANSI C63.4: Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz FCC Classification: DSS – Part 15 Spread Spectrum Transmitter Frequency Hopping FCC Rule Part(s): Part 15.247: Operation within the bands 920-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz Frequency Hopping System Industry Canada Standard: RSS-210: Low Power License-Exempt Radio Communication Devices (All Frequency Bands) Digital Interface Information Digital Interface was found to be compliant Receiver Information Receiver was found to be compliant Frequency Range (MHz) Output Power* (W) Frequency Tolerance Emission Designator 902.8-927.6 0.028 N/A N/A * output power is maximum peak conducted We, the undersigned, hereby declare that the equipment tested and referenced in this report conforms to the identified standard(s) as described in this test report. Furthermore, there was no deviation from, additions to, or exclusions from the FCC Part 2, FCC Part 15, Industry Canada RSS-210 and ANSI C63.4. Signature: Date: March 26, 2004 Typed/Printed Name: Desmond A. Fraser Position: President Rhein Tech Laboratories Client: Paxar Americas, Inc. 360 Herndon Parkway FCC: Part 15.247 Suite 1400 IC: RSS-210 FCC ID: GU6WJSX2000 Herndon, VA 20170 http://www.rheintech.com Model : AlienC1915 Page 2 of 65 TABLE OF CONTENTS 1 GENERAL INFORMATION ........................................................................................................................................................................................... 5 1.1 SCOPE ........................................................................................................................................................................................5 1.2 TEST FACILITY ........................................................................................................................................................................5 1.3 RELATED SUBMITTAL(S)/GRANT(S)...................................................................................................................................5 1.4 MODIFICATIONS .....................................................................................................................................................................5 2 TEST INFORMATION.................................................................................................................................................................................................... 6 2.1 TEST JUSTIFICATION .............................................................................................................................................................6 2.2 EXERCISING THE EUT ............................................................................................................................................................6 2.3 TEST RESULT SUMMARY ......................................................................................................................................................6 2.4 TEST SYSTEM DETAILS .........................................................................................................................................................7 2.5 CONFIGURATION OF TESTED SYSTEM ..............................................................................................................................7 3 COMPLIANCE WITH THE RESTRICTED BAND EDGE – FCC §15.205; IC RSS-210 §6.3....................................................................................... 8 3.1 TEST PROCEDURE...................................................................................................................................................................8 3.2 BAND EDGE TEST EQUIPMENT............................................................................................................................................8 3.3 COMPLIANCE WITH THE RESTRICTED BAND EDGE TEST DATA ................................................................................8 4 CONDUCTED LIMITS – FCC §15.207; IC RSS-210 §6.6 AND 7.4 ........................................................................................................................... 11 4.1 CONDUCTED TEST DATA .........................................…

Text truncated - open the document above for the full version.