H52PT-3029Modem Card

UserUser UserUser User ’’ ’’ ’ s Manuals Manual s Manuals Manual s Manual VV VV V erer erer er . A 3029-0008. A 3029-0008 . A 3029-0008. A 3029-0008 . A 3029-0008 56K PCI 56K PCI 56K PCI 56K PCI 56K PCI MM MM M odemodem odemodem odem FCC Part 15FCC Part 15 FCC Part 15FCC Part 15 FCC Part 15 Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interfer- ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: § Reorient or relocate the receiving antenna. § Increase the separation between the equipment and receiver. § Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. § Consult the dealer or an experienced radio/ TV technician for help. Any changes or modifications not expressly approved by the grantee of this device could void the user authority to operate the equipment. FCC Part 68 NoticeFCC Part 68 Notice FCC Part 68 NoticeFCC Part 68 Notice FCC Part 68 Notice This equipment complies with Part 68 of the FCC rules. On the base of this unit is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be given to your telephone company. The REN is used to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. In most, but not all areas, the sum of the RENs of all devices should not exceed five (5.0). To be certain of the number of devices you may connect to your line, as determined by the total RENs, you should call your local tel- ephone company to determine the maximum RENs for your calling area. If the telephone company suspects a problem with your telephone line is related to an add-on Caution electronic device, such as your modem, they have the right to temporarily suspend your service. It is your responsibility to remove from the telephone line any malfunctioning electronic communications equipment to avoid damage to the telephone system. If your equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a com- plaint with the FCC. Your telephone company may make changes to its facilities, equipment, opera- tions, or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. The telephone company may ask that you discon- nect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subjected to state tariffs. If you experience trouble with this telephone equipment, please contact your place of purchase for information on obtaining service or repairs. TT TT T able of Contentsable of Contents able of Contentsable of Contents able of Contents Chapter 1 IntroductionChapter 1 Introduction Chapter 1 IntroductionChapter 1 Introduction Chapter 1 Introduction Your Modem ..................................... 1 Features............................................... 2 System Requirements......................... 2 Package Checklist .............................. 3 Chapter 2 InstallationsChapter 2 Installations Chapter 2 InstallationsChapter 2 Installations Chapter 2 Installations Hardware Installation .............. ........... 4 Installation Procedures for Windows NT4.0 driver ............ .......... 5 Installation Procedures for Windows 98 driver ................. ......... 6 Installation of Procedures for Windows 2000 driver ...................... 10 AT Command .................................... 11 Chapter 1 IntroductionIntroduction IntroductionIntroduction Introduction The Voice/Fax/Data Modem connects your computer to Internet, and all kinds of BBS, and other popular Fax / Modems. This manual describes the features, procedures of installations, and AT command set... etc. of this modem. YY YY Y our modem...our modem... our modem...our modem... our modem... There are indicator lights and connectors on the front and back side of this modem. Following is the meaning of these light and connectors for your reference: 1. External Front Panel 1. External Front Panel 1. External Front Panel 1. External Front Panel 1. External Front Panel RD : Received Data indicator. TD : Transmitted Data indicator. CD : Carrier Detect indicator. OH : Off Hook. MR : Modem Ready. PHONE : Phone jack. LINE : Telephone line jack. RS232 : RS232 cable socket. AC-IN : AC adapter input. ON/OFF : Power switch. 2. External Rear Panel2. External Rear Panel 2. External Rear Panel2. External Rear Panel 2. External Rear Panel 1 2 Chapter 1 FeaturesFeatures FeaturesFeatures Features This modem supports the following communica- tion standards. ITU-T is known as CCITT. DataData DataData Data ITU-T V.90 z ITU-T V.34, V.32bis, V.32, V.22bis, V.22 Bell …

Text truncated - open the document above for the full version.

FCC ID : H52PT-3029

FCC ID : H52PT-3029Front side of EUT Number 1 071801-01.jpg FCC ID : H52PT-3029Rear side of EUT Number 2 071801-03.jpg

EXHIBIT A. FCC ID LABEL FCC ID:H52PT-3029 The next page shows the location of FCC ID on EUT. FCC ID: H52PT-3029 0.5CM 4CM The following statement will be placed in the User’s Manual. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID : H52PT-3029Front side of EUT Number 1 071801-01.jpg FCC ID : H52PT-3029Rear side of EUT Number 2 071801-03.jpg

FCC TEST REPORT Report No. : F071801 SPORTON International Inc. FCC ID: H52PT-3029 TEL : 886-2-2696-2468Page No.: 1 of 22 FAX : 886-2-2696-2255Issued Date : Aug. 9, 2000 FCC TEST REPORT for CISPR PUB. 22 Class B Equipment: MODEM CARD Model No.: PT-3029 FCC ID: H52PT-3029 Filing Type: Original Grant Applicant: PURETEK INDUSTRIAL CO., LTD. 4F, NO. 12, LANE 235, PAO-CHIAO RD., HSINTIEN CITY, TAIPEI, TAIWAN, R.O.C. ! The test result refers exclusively to the test presented test model / sample. ! Without the written authorization of the test lab., the Test Report may not be copied. ! Certificate or Test Report must not be used by the applicant to claim the product in this test report endorsement by NVLAP or any agency of U.S. government. SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. FCC TEST REPORT Report No. : F071801 SPORTON International Inc. FCC ID: H52PT-3029 TEL : 886-2-2696-2468Page No.: 2 of 22 FAX : 886-2-2696-2255Issued Date : Aug. 9, 2000 Table of Contents CERTIFICATE OF COMPLIANCE .............................................................................................................. 3 1. General Description of Equipment under Test..................................................................................... 4 1.1. Applicant .............................................................................................................................................................................................................. 4 1.2. Manufac turer ....................................................................................................................................................................................................... 4 1.3. Basic Description of Equipme nt under Test................................................................................................................................................... 4 1.4. Feature of Eq uipment under Tes t.................................................................................................................................................................... 4 2. Test Configuration of Equipment under Test....................................................................................... 5 2.1. Test Ma nner ........................................................................................................................................................................................................ 5 2.2. Description of Test S ystem............................................................................................................................................................................... 5 2.3. Connec tion Diagram o f Test Sys tem .............................................................................................................................................................. 7 3. Test Software ....................................................................................................................................... 8 4. General Information of Test ................................................................................................................. 9 4.1. Test Facility ......................................................................................................................................................................................................... 9 4.2. Standard for Methods o f Meas ure ment .......................................................................................................................................................... 9 4.3. Test in Comp liance with .................................................................................................................................................................................... 9 4.4. Freque nc y Range Investigated ........................................................................................................................................................................ 9 4.5. Test Distance ...................................................................................................................................................................................................... 9 5. Test of Conducted Powerline............................................................................................................. 10 5.1. Major Measuring Instrume nts .........................................................................................................................................................................10 5.2. Test Procedures ...............................................................................................................................................................................................11 5.3. Typical Test Setup La yo ut o f Co nduc ted Powerline ...................................................................................................................................12 5.4. Test Res ult o f AC Powerline Cond ucted Emission.....................................................................................................................................13 5.5. Photograp hs o f Cond uc ted Powerline Tes t Configuration.........................................................................................................................14 6. Test of Radiated Emission.................................................................................................................. 16 6.1. Major Measuring Instrume nts .........................................................................................................................................................................16 6.2. Test Procedures ...............................................................................................................................................................................................17 6.3. Typic…

Text truncated - open the document above for the full version.

1.1. Photographs of Conducted Powerline Test Configuration ! The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW SIDE VIEW 1.2. Photographs of Radiated Emission Test Configuration ! The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW