
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
MODEL X11RF-LCD REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5. Always apply the parking brake and lock the vehicle as you exit the vehicle. 6. The vehicle windows must be rolled up. 7. Should the unit malfunction, disconnect the fuse until the problem is corrected. 8. The use and operations of this system is the sole responsibility of the operator. 9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets. 10. Do not start the vehicle by remote while the standard transmission vehicle is parked at a steep place. 1 TABLE OF CONTENTS: A. REMOTE TRANSMITTER OPERATION ................................................................................................. 4 B. 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION ................................................................. 4 C. LED DISPLAY .................................................................................................................................... 4 D. CHIRP INDICATOR .............................................................................................................................. 4 E. PARKING LIGHT ................................................................................................................................. 4 F. ACTIVE ARMING – ARM & LOCK .......................................................................................................... 4 Ajar Warning / Silent Arming / Disarming / Sensor By-Pass / Hidden Alarm Mode G. PASSIVE ARMING .............................................................................................................................. 5 Passive Arming with Passive Door Locking / Passive Arming By-Pass H. ACTIVE DISARMING – UNLOCK & DISARM ........................................................................................... 5 Tamper Disarming / Pathway Illumination / Two Steps Door Unlock / Automatic Re-Arm I. DISARMING WITHOUT A TRANSMITTER ................................................................................................ 6 Overrides the Alarm without Password Pin Code / Overrides the Alarm With Password Pin Code J. VALET MODE ..................................................................................................................................... 6 K. CAR LOCATOR .................................................................................................................................. 7 L. PANIC FUNCTION ............................................................................................................................... 7 M. TRIGGER THE SYSTEM ....................................................................................................................... 7 Stop The Melody Sound / Noise Abatement Circuit N. ANTI CAR- JACKING ........................................................................................................................... 7 O. SYSTEM’S TRIGGER CHECK ............................................................................................................... 8 P. SYSTEM’S STATUS CHECK ................................................................................................................. 8 Q. DRIVER PAGING / LOSE AND FOUND ................................................................................................... 8 R. DOME LIGHT CONVENIENCE DELAY & SUPERVISION ........................................................................... 8 S. IGNITION CONTROL THE DOOR LOCK/UNLOCK. ................................................................................... 9 T. TRUNK RELEASE (CHANNEL 3) OUTPUT .............................................................................................. 9 U. CHANNEL 4 / 5 / 6 / 7 TIMER CONTROL OUTPUT .................................................................................... 9 V. POWER ON MEMONRY: ....................................................................................................................... 9 REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE ....................................................................................................... 9 B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START .................................................. 9 C. TEMPORARY STOP FEATURE ............................................................................................................. 9 D. TURBO TIMER MODE ......................................................................................................................... 10 E. TIMER / TEMPERATURE START .......................................................................................................... 10 3 (2 or 1) Hours Timer Start / Daily Timer Start / Cancel the Timer Start F. TEMPERATURE CHECK .................................................................................................................... 10 G. TO TURN OFF THE REMOTE START ......................................................................................................11 H. SHUT-DOWN INPUT FOR REMOTE STARTER ....................................................................................... 11 I. DISABLING THE REMOTE START SYSTEM ............................................................................................ 11 LCD REMOTE TRANSCEIVER: A. BATTERY REPLACEMENT ................................................................................................................... 11 B. THE REMOTE LCD ICONS WITH FUNCTION .................................................…
Text truncated - open the document above for the full version.
ADVANCE SECURITY INC. 3F, 48 Ta An Street, Hsi Chih, Phone : (886-2) 8648-1688 E-mail : adv4758 @ms11.hinet.net Taipei Hsien, TAIWAN R.O.C. Te l e x f a x : (886-2) 8648-1689 01/14/2008 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, the undersigned, hereby authorize ETS Product Service (Taiwan) Co., Ltd. to act on our behalf in all matters relating to applications for“Remote Control” (Model No.: X11RF-LCD, FCC ID: H5OTR26)" authorization, including the signing of all documents relating to these matters. Any and all acts carried out by ETS Product Service (Taiwan) Co., Ltd. on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Signature: Name: Ted Lin Title: SALES MANAGER Company: Advance Security Inc.
ADVANCE SECURITY INC. 3F, 48 Ta An Street, Hsi Chih, Phone : (886-2) 8648-1688 E-mail : adv4758 @ms11.hinet.net Taipei Hsien, TAIWAN R.O.C. Te l e x f a x : (886-2) 8648-1689 Federal Communications Commission FCC ID: H5OTR26 Dear Sir: This is to request confidentiality on information submitted for above application. We would like to request confidentiality on some exhibits we submitted for above original application for the reason of trade secret. If those exhibits are available for public inspection, any person who once gets the information contained in those exhibits will be able to design and to make the same products very easily. This is a very serious problem and huge loss for us, because we did invest so much on it. Please be not made the Exhibit Types listed below routinely available for public inspection. Confidentiality Request regarding application for certification of FCC ID: H5OTR26 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Block diagram, schematics, operational description By: By: (Signature) (Printed) Title : SALES MANAGER Applicant : Advance Security Inc. Address : 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Tel : +886-2-86481688 Fax:+886-2-86481689 Date : January 14, 2008
Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 51 of 60 External Photos Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 52 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 53 of 60
FCC ID LABEL AND LOCATION FCC ID: H5OTR26 Model No.: X11RF-LCD This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 21 mm 10 mm
Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 54 of 60 Internal Photos Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 55 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 56 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 57 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 58 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 59 of 60
MPE Prediction FCC Rule: 15.247(b)(5) Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. See §1.1307(b)(1) of this Chapter. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average time (minutes) (A)Limits For Occupational / Control Exposures 30-300 61.4 0.613 1.0 6 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 30-300 27.5 0.073 0.2 30 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 PG S = -------------- 4πR² where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Maximum peak output power at antenna input terminal: 18.85 (dBm) Maximum peak output power at antenna input terminal: 78.52356 (mW) Antenna gain(maximal): 5.0 (dBi) Prediction distance: 20 (cm) Prediction frequency: 915.5 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 1.0 (mW/cm²) Power density at prediction frequency: 0.078 (mW/cm²) The manual instruct the user to install and operate the device in a minimum distance of 20 cm between antenna and the user’s body.
of Applicant: Advance Security Inc. Address: 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Tested and Prepared by Taiwan ETS Product Service Co., Ltd. FCC Registration No.: 930600 Industry Canada filed test laboratory Reg. No. IC 5679A-1 A2LA Accredited No.: 1983.02 PTCRB Accredited Type Certification Test House Report No.: W6M20801-8817-P-15 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC PART 15 SUBPART C TEST REPORT for Remote Control Model No.: X11RF-LCD FCC ID: H5OTR26 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Page 1 of 30 TABLE OF CONTENTS 1 GENERAL INFORMATION ...................................................................................................... 2 1.1 Notes .................................................................................................................................... 2 1.2 Testing laboratory ................................................................................................................ 3 1.2.1 Location .......................................................................................................................3 1.2.2 Details of accreditation status ..................................................................................... 3 1.3 Details of approval holder.................................................................................................... 3 1.4 Application details ............................................................................................................... 4 1.5 General information of Test item......................................................................................... 4 1.6 Test standards....................................................................................................................... 5 2 TECHNICAL TEST .................................................................................................................... 6 2.1 Summary of test results........................................................................................................ 6 2.2 Test environment.................................................................................................................. 6 2.3 Test Equipment List ............................................................................................................. 7 2.4 General Test Procedure ........................................................................................................ 9 3 TEST RESULTS (ENCLOSURE)............................................................................................. 11 3.1 Peak Output Power (transmitter)........................................................................................ 12 3.2 RF Exposure Compliance Requirements ........................................................................... 14 3.3 Out of Band Radiated Emissions ....................................................................................... 14 3.4 Transmitter Radiated Emissions in restricted Bands ......................................................... 15 3.5 Spurious emissions (tx) ...................................................................................................... 16 3.6 Carrier Frequency Separation ............................................................................................ 20 3.7 Number of Hopping Frequencies ....................................................................................... 21 3.7.1 Pseudorandom Frequency Hopping Sequence ......................................................... 22 3.7.2 Coordination of hopping sequences to other transmitters......................................... 22 3.7.3 System Receiver Hopping Capability......................................................................... 22 3.7.4 Equal Hopping Frequency Use.................................................................................. 22 3.8 Time of Occupancy (Dwell Time) ..................................................................................... 23 3.9 20dB Bandwidth ................................................................................................................ 24 3.9.1 System Receiver Input Bandwidth.............................................................................. 24 3.10 Band-edge Compliance of RF Emissions .......................................................................... 25 3.11 Radiated Emissions from Receiver Section of Transceiver............................................... 26 3.12 Power Line Conducted Emission ....................................................................................... 29 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Page 2 of 30 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the Taiwan ETS Product Service Co., Ltd. Tester: January 25, 2008 Jay Chaing Da…
Text truncated - open the document above for the full version.
Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 35 of 60 Band-edge Compliance of RF Conducted Emissions Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 36 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 37 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 38 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 39 of 60 Radiated Emissions from Receiver Section of Transceiver ch 1 Antenna Polarization H Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 40 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 41 of 60 Antenna Polarization V Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 42 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 43 of 60 ch 13 Antenna Polarization H Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 44 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 45 of 60 Antenna Polarization V Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 46 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 47 of 60 ch 25 Antenna Polarization H Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 48 of 60 Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 49 of 60 Antenna Polarization V Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 50 of 60
Registration number: W6M20801-8817-P-15 FCC ID: H5OTR26 Taiwan ETS Product Service Co., Ltd. Appendix page 60 of 60 Set Up Photo of Radiated Emission
6F., No. 58, Lane 188, Ruey Kuand Rd., Neihu · Taipei · Taiwan
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 909 MHz - 921.778 MHz | 78.52 mW |

Remote Control
Equipment Class
DSC - Part 15 Security/Remote Control Transmitter
Remote Control
Equipment Class
CYY - Communications Receiver used w/Pt 15 Transmitter
Remote Control
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter
Remote Control
Equipment Class
CYY - Communications Receiver used w/Pt 15 Transmitter
Remote Control
Equipment Class
DSC - Part 15 Security/Remote Control Transmitter