H5OTR48Remote Control

Page 1 128-9103 1 of 26 ARMING THE SYSTEM - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid and trunk lid. 2. Press and release Lock/Arm button on the keychain trans- mitter. The dash mounted LED begins to flash slowly. Parking Lights flash one time. Siren sounds one chirp. If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. Simply close the opened entry point to provide full pro- tection. If the siren "chirped" three times, sometime after arming, the exclusive, patented, delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Again, closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. If the siren/horn did not sound when arming, then the chirps have been turned off and you should refer to the section titled "ELIMINATING THE ARM/ DISARM CHIRPS" in this manual. NOTE: If selectable feature 9, Chirp Delete From Transmitter, was set to the on position during installation, then you can selectively defeat the arm & disarm chirps by holding the transmitters Lock or Unlock button for about 2 seconds. NOTE: If Passive Arm Mode was selected on during installation, then 30 seconds after the last vehicle door is closed, the unit will arm automatically. PROTECTION WHILE THE SYSTEM IS ARMED Opening any protected door, hood or trunk lid will cause the alarm to immediately sound. The alarm will continue to sound for 30 seconds, then stop and continue to monitor all protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone. Whenever the system is armed, the LED indicator will slowly flash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle’s battery to drain, even when left unattended for extended periods. Whenever the system is triggered, the vehicle’s parking lights will flash for the full 30 second alarm cycle, attracting visual attention to the vehicle. Optional - Whenever the system is armed, the vehicle’s starting circuit will be prevented. If the thief should choose to ignore the siren, the vehicle can not be started. Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE:If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle. DISARMING THE SYSTEM 1. As you approach the vehicle, press and release the Unlock/Disarm button on the keychain transmitter. The siren or horn chirps twice, the parking lights flash twice, and the LED turns off. Model PA-920C Owners Manual 128-9103 2 of 26 Page 2 If passive arming is selected on, the LED will start flashing rapidly, indicating that the system is re-arming automatically. Open any door to suspend the automatic arming. If the siren chirps 4 times and the parking lights flashed three times, then the alarm was triggered in your absence. If the siren did not sound when disarming, then the chirps have been turned off and you should refer to the section titled “ELIMINATING THE ARM / DISARM CHIRPS“ in this manual.    Doors Unlock - Optional NOTE:If the optional Interior illumination feature has been added as an added convenience, the system will turn on the interior lights when the system is disarmed. WHILE THE SYSTEM IS SOUNDING If during a triggered state, you wish to shut off the siren without disarming your security system, simply press and release any transmitter button other than the Unlock/Disarm button. This action will turn off the siren yet leave the vehicle fully armed and protected. This feature is particularly useful if you are aware of children playing near your vehicle that may accidently trigger your security system. In this case you can cancel the siren sounding without disarming your alarm. INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle and observe the red LED to identify which zone was triggered.   If the LED is flashing one time...pause...one time...pause...etc., then an intrusion attempt was made to the shock sensor, or an accessory triggering device that may have been added to the system.    If the LED is flashing two times...pause...two times...pause...etc., then an intrusion attempt was made to a hood or trunk pin switch that was added to the system.    If the LED is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors. These intrusion warning indicators are stored in the system’s memory and will only be erased when the ignition key is turned on. VALET SWITCH The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational. In addition, the parking lights will flash to indicate locking and unlocking. To use the valet mode, the system must first be disarmed either by using your keychain transmitter or by use of the the manual override switch. 1. Enter the vehicle and turn the ignition key to the on position. 2. Press and hold the valet pushbutton switch until the LED turns on solid. 3. To return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE:Always remember to return the system to normal operation. This will ensure that the…

Text truncated - open the document above for the full version.

Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 2 of 14 External Photos Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 3 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 4 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 5 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 6 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 7 of 14

FCC ID label & location www.PS-TRANS.com PA92 FCC ID: H5OTR48

Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 8 of 14 Internal Photos Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 9 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 10 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 11 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 12 of 14 Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 13 of 14

of Applicant: Advance Security Inc. Address: 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Tested and Prepared by Worldwide Testing Services (Taiwan) Co., Ltd. FCC Registration No.: 930600 Industry Canada filed test laboratory Reg. No. IC 5679A-1 A2LA Accredited No.: 2732.01 Report No.: W6M21208-12661-C-1 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC PART 15 SUBPART C TEST REPORT for Remote Control Model No.: PA92 FCC ID: H5OTR48 Registration number: W6M21208-12661-C-1 FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Page 1 of 22 TABLE OF CONTENTS 1 General Information........................................................................................................................2 1.1 Notes ..........................................................................................................................................2 1.2 Testing laboratory .......................................................................................................................3 1.2.1 Location ..................................................................................................................................3 1.2.2 Details of accreditation status ................................................................................................3 1.3 Details of approval holder...........................................................................................................3 1.4 Application details ......................................................................................................................4 1.5 Test item .....................................................................................................................................4 1.6 Test standards .............................................................................................................................4 2 Technical test ..................................................................................................................................5 2.1 Summary of test results...............................................................................................................5 2.2 Test environment ........................................................................................................................5 2.3 Test Mode ...................................................................................................................................5 2.4 Test equipment utilized...............................................................................................................6 2.5 General Test Procedure.............................................................................................................10 3 Test results (enclosure) .................................................................................................................11 3.1 Transmission Requirements......................................................................................................12 3.1.1 Limit of Transmission Time ..................................................................................................12 3.1.2 Active Time ...........................................................................................................................12 3.2 Output Power (Field Strength)..................................................................................................13 3.3 Out of Band Radiated Emissions ..............................................................................................14 3.4 Transmitter Radiated Emissions in restricted Bands ................................................................15 3.5 Spurious Emission radiated, Transmitter ..................................................................................16 3.6 Channel Bandwidth...................................................................................................................18 3.7 Antenna requirement.................................................................................................................19 3.8 Duty Cycle ................................................................................................................................20 3.9 Conducted Measurement at (AC) Power Line..........................................................................21 Appendix: Diagrams Registration number: W6M21208-12661-C-1 FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Page 2 of 22 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the Worldwide Testing Services(Taiwan) Co., Ltd. Tester: August 29, 2012 Leon Chueh Date WTS-Lab. Name Signature Technical responsibility for area of testing: August 29, 2012 Danny Sung Date WTS Name Signature Registration number: W6M21208-12661-C-1 FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Page 3 of 22 1.2 Testing laboratory 1.2.1 Location OATS No.5-1, Lishui, Shuang…

Text truncated - open the document above for the full version.

Registration number: W6M21208-12661-FCC FCC ID: H5OTR48 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 14 of 14 Set Up Photo of Radiated Emission RF mode