H5OTR52Remote Control

1 Keypad Authentication Authenticating the ACM keypad Each ACM keypad must be authenticated daily to enable it’s use and upload it’s stored data. Authentication takes place automatically the first time the PWR (power) button is pressed, providing it is within the time slot for that particular keypad and within range of the ACM. 2 GREEN flashes, indicate the keypad is authenticated for use, 2 RED flashes indicate that the keypad is not authorized for use. Check your LMS settings to ensure the correct time of day is entered for the keypads user profile if the keypad does not authenticate. De-authenticating the ACM keypad De-authenticating the keypad will disable it’s use until it has been re-authenticated as mentioned above. If changes are made in LMS after a keypad has been authenticated it will be necessary to re-authenticate the keypad in order for those changes to take effect. To De-authenticate or “Zero out” the keypad press the power button then press and hold the 0 key for 10 seconds, the LED will flash 2 times indicating the keypad has been de-authenticated. Accessing Vehicles The keypad will access each vehicle individually based on the vehicle’s stock number. Access a vehicle by following the steps below. 1. Press the PWR button - if necessary enter your 4 digit PIN. 2. Enter the vehicle stock number. 3. Press the button of the function you wish to activate. (lock, unlock, etc..) Note: The 4 digit PIN mentioned in step 1 is only necessary if PIN Code has been enabled in the LMS website for your keypad. PROLMSTX - ACM Keypad Transitioning into No-Sale Mode - Yellow 1.Open a vehicle door. 2.Enter the vehicle number into an ACM keypad. 3.Press the UNLOCK button. 4.Press and release the TRANS button. 5.Press and release the “YELLOW” button. 6.Close the vehicle’s door. Note: The ACM keypad must be authorized for transitioning. Note: No-Sale mode disables all functionality of the unit, the unit will be inoperable until reprogrammed with the PROFLASH pro- gramming device. This mode is only used when there is a no-sale of the product and you are not removing the system from the vehicle. Transitioning into ITS Mode - Green 1.Open a vehicle door. 2.Enter the vehicle number into an ACM keypad. 3.Press the UNLOCK button. 4.Press and release the TRANS button. 5.Press and release the “GREEN” button. 6.Close the vehicle’s door. Note: The ACM keypad must be authorized for transitioning. Note: ITS mode enables the shock sensor only of this device for applications in a vehicle equipped with a factory security system. Lot Mode / Consumer Mode Transitioning 2 Transitioning into Factory Keyless Upgrade Mode - Blue 1.Open a vehicle door. 2.Enter the vehicle number into an ACM keypad. 3.Press the UNLOCK button. 4.Press and release the TRANS button. 5.Press and release the “BLUE” button. 6.The LED will flash blue 1 time and the system will chirp 3 times. 7.Close the vehicle’s door.. Note: The ACM keypad must be authorized for transitioning. Note: Factory Keyless Upgrade Mode enables all of the device’s security functionality by use of the factory transmitters. Transitioning into Security with Transmitters Mode - Red 1.Open a vehicle door. 2.Enter the vehicle number into an ACM keypad. 3.Press the UNLOCK button. 4.Press and release the TRANS button. 5.Press and release the “RED” button. 6.The LED will flash red 1 time and the system will chirp 3 times. 7.Within 5 seconds, program the aftermarket transmitter by pressing the lock button of each transmitter you wish to program. 8.Close the vehicle’s door.. Note: The ACM keypad must be authorized for transitioning. Note: If no remotes are programmed during step 7, the system will automatically transition into the Factory Keyless Upgrade Mode - BLUE Note: Security with Transmitters Mode enables all of the device’s security functionality by use of aftermarket transmitters. Transitioning into Lot Mode 1.Turn the ignition ON. 2.Press and release the override button 3 times. 3.The system will chirp 1 time. 4.Press button 1 of the short range transmitter. 5.The system will respond with 1 chirp. 6.Turn the ignition OFF to exit transmitter programming. 7.The system will chirp 2 times to confirm exit. Note: This system has 1 button programming which programs all channels of the transmitter to the system at once. When in lot mode, a consumer remote can not be programmed to the system until it is transitioned to consumer mode. All programming features will be defaulted to the factory default settings. 3 Lost or Forgotten Keypad Pin Codes Resetting a Keypad with an Unknown Pin Code The following procedure will take you through the process of resetting a PIN on a Keypad if the current PIN is unknown. 1.Login to the LMS website & locate the Keypad in question. 2.Deselect the “PIN REQUIRED” check box for that Keypad. 3.Select “SAVE”. Note: If the Keypad has already been authenticated for the day with the unknown PIN, you must wait until the keypad operating time has expired for the day before carrying out these next steps: 1.Authenticate the Keypad. 2.Press and hold the “*” button on the Keypad for 10 seconds until the light flashes green 4 times. 3.Enter in the new 4 digit PIN within 10 seconds, the light will flash back green 3 times. 4.Re-enter the new PIN again to confirm your entry, the light will flash back green 4 times. 5.Press and hold the “0” button on the Keypad for 10 seconds until the light flashes green 3 times. 6.Login to the LMS and locate the Keypad in question again. 7.Select the “PIN REQUIRED” check box for that Keypad. 8.Select “SAVE”. 9.Re-Authenticate the Keypad, it should now be operating with the new PIN number. Master Keypad A Master Keypad does has 24 access to vehicles without the need of authentication from the ACM. This is intended to be placed in a secured location such as a safe to be used in case of an outage. A master keypad will only work with the dealer it is registered with in the LMS website. Federal Communication Commission Interferenc…

Text truncated - open the document above for the full version.

Advance Security Inc. 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2012-12-11 To whom it may concern: We, the undersigned, hereby authorize Worldwide Testing Services (Taiwan) Co., Ltd to act on our behalf in all matters relating to applications for equipment authorization FCC ID: H5OTR52 including the signing of all documents related to these matters. Any and all acts carried out by Worldwide Testing Services (Taiwan) Co., Ltd on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Signature Name: Ted Lin Title: VICE PRESIDENT MARKETING & SALES Company: Advance Security Inc.

Advance Security Inc. 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2012-12-11 Request for Confidentiality Company name: Advance Security Inc. FCC ID: H5OTR52 FCC Part 15 Certification To whom it may concern: In accordance with 0.459 of CFR 47, Advance Security Inc. hereby requests confidentiality of all Block Diagrams, Schematics, Operational Description attachments for the subject application. These documents contain detailed system and equipment description and related information about the product which Advance Security Inc. considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, Advance Security Inc. considers that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Signature Name: Ted Lin Title: VICE PRESIDENT MARKETING & SALES Company: Advance Security Inc.

Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 2 of 17 External Photos Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 3 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 4 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 5 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 6 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 7 of 17

Model no.: PROLMSTX FCC ID: H5OTR52

Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 8 of 17 Internal Photos Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 9 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 10 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 11 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 12 of 17 Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 13 of 17

Advance Security Inc. 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Applicant’s declaration concerning RF Radiation Exposure We hereby indicate that the product Product description: Remote Control Model No: PROLMSTX The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The integral antennas used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter within the host device. A safety statement concerning minimum separation distances from enclosure of the Product : Remote Control will be integrated in the user’s manual to provide end-users with transmitter operating conditions for satisfying RF exposure compliance. The appropriate information can be drawn from the test report no: W6M21212-12925-C-1 and the accompanying calculations. Company: Advance Security Inc. Address: 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Date: 2012-12-11 Signature Registration number: W6M21212-12925-C-1 FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Page 17 of 35 3.2 Equivalent isotropic radiated power FCC Rule: 15.247(b)(3) EIRP = max. conducted output power + antenna gain EIRP = 11.19 dBm + 1 dBi = 12.19 dBm Limit: EIRP = +36 dBm for Antenna gain <6dBi Test equipment used: ETSTW-RE 055 3.3 RF Exposure Compliance Requirements FCC OET Bulletin 65 Edition 97.01 determines the equations for predicting RF fields and applicable limits. The prediction for power density in the far-field but will over-predict power density in the near field, where it could be used for walking a “worst case” or conservative prediction. PG S = --------- 4πR 2 S – Power Density P – Output power ERP R – Distance D – Cable Loss AG – Antenna Gain Item Unit Value Remarks P mW 13.152 Peak value D dB AG dBi 1 G 1.26 Calculated Value R cm 20 Assumed value S mW/cm 2 0.0033 Calculated value Limits: Limit for General Population / Uncontrolled Exposure Frequency (MHz) Power Density (mW/cm 2 ) 1500 – 100.000 1.0

of Applicant: Advance Security Inc. Address: 3F, 48 Ta-An Street, Hsi-Chih Taipei Hsien, Taiwan R.O.C. Tested and Prepared by Worldwide Testing Services (Taiwan) Co., Ltd. FCC Registration No.: 930600 Industry Canada filed test laboratory Reg. No. IC 5679A-1 A2LA Accredited No.: 2732.01 Report No.: W6M21212-12925-C-1 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC PART 15 SUBPART C TEST REPORT for Remote Control Model No.: PROLMSTX FCC ID: H5OTR52 Registration number: W6M21212-12925-C-1 FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Page 1 of 35 TABLE OF CONTENTS 1 GENERAL INFORMATION ..........................................................................................................2 1.1 NOTES..........................................................................................................................................2 1.2 T ESTING LABORATORY................................................................................................................3 1.2.1 Location ..................................................................................................................................3 1.2.2 Details of accreditation status ................................................................................................3 1.3 D ETAILS OF APPROVAL HOLDER...................................................................................................3 1.4 A PPLICATION DETAILS.................................................................................................................4 1.5 G ENERAL INFORMATION OF TEST ITEM........................................................................................4 1.6 TEST STANDARDS.........................................................................................................................5 2 TECHNICAL TEST .........................................................................................................................6 2.1 S UMMARY OF TEST RESULTS........................................................................................................6 2.2 TEST ENVIRONMENT....................................................................................................................6 2.3 TEST EQUIPMENT LIST.................................................................................................................7 2.4 G ENERAL TEST PROCEDURE......................................................................................................11 3 TEST RESULTS (ENCLOSURE) ................................................................................................13 3.1 PEAK OUTPUT POWER (TRANSMITTER) ......................................................................................14 3.2 EQUIVALENT ISOTROPIC RADIATED POWER................................................................................17 3.3 RF EXPOSURE COMPLIANCE REQUIREMENTS............................................................................17 3.4 T RANSMITTER RADIATED EMISSIONS IN RESTRICTED BANDS....................................................18 3.5 SPURIOUS EMISSIONS (TX) .........................................................................................................19 3.6 RADIATED EMISSION ON THE BAND EDGE..................................................................................23 3.7 MINIMUM 6 DB BANDWIDTH.....................................................................................................25 3.8 P EAK POWER SPECTRAL DENSITY.............................................................................................28 3.9 R ADIATED EMISSION FROM DIGITAL PART................................................................................31 3.10 P OWER LINE CONDUCTED EMISSION.........................................................................................32 Registration number: W6M21212-12925-C-1 FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Page 2 of 35 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the Worldwide Testing Services(Taiwan) Co., Ltd. Specific Conditions: Usage of the hereunder tested device in combination with other integrated or external antennas requires at least additional output power measurements, spurious emission measurements, conducted emission measurements (AC supply lines) and radio frequency exposure evaluations for each individual configuration performed, for certification by FCC. The test sample is able to work according Zigbee. This report is related to FCC Part 15 C (OQPSK device). Tester: December 18, 2012 Spencer Yang Date WTS-Lab. Name Signature Technical responsibility for area of testing: December 18, 2012 Danny Sung Date WTS Name Signature Registration number: W6M21212-12925-C-1 FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Page 3 of 35 1.2 Testing laboratory 1.2.1 Location OATS No.5-1, Lishui, Shuang Sing Village, Wanli …

Text truncated - open the document above for the full version.

Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 14 of 17 Set Up Photo of Radiated Emission EMI Below 1GHz Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 15 of 17 Above 1GHz Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 16 of 17 RF Registration number: W6M21212-12925-FCC FCC ID: H5OTR52 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 17 of 17 Set Up Photo of Conducted Emission