HBW-GDOCAM3Hawkeye 3 Camera Module

Decorative Ring To prevent damage to the camera, push the camera lens closed when replacing, and hold it in place as you remove securing hardware. DO NOT touch the camera logic board during installation. ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment. Introduction Installation CAMERA SERVICE KIT REPLACEMENT Model 041-0041 Your camera is accessible at the opener’s bottom side. After installing the new camera, use your myQ ® app to connect your new camera to your myQ ® account. 1. Disconnect power to the garage door opener, and remove the backup battery, if used. To prevent possible SERIOUS INJURY or DEATH: • Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance. WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. 2. Remove the decorative ring at the opener’s bottom. 3. Unscrew the camera slowly from the opener housing. TIP: Use masking tape to hold the camera in place as you remove screws. 5. Plug in the new camera. 6. Align and screw in the new camera into the opener housing. 7. Attach the new decorative ring. 8. Reconnect power and battery, if used. 10. Follow the myQ ® App instructions to add the new camera to your myQ ® account. NOTE: Only the replacement camera needs to be provisioned (not the garage door opener) using myQ ® app. Camera LED Status Indicators WHAT YOU SEEWHAT IT MEANS Solid WhiteCamera is powering up. Flashing BlueReady to be set up in the myQ ® App. Solid BlueConnected to your mobile device. You are not yet connected to the Internet. If this persists after setup, check your home router and Internet. Connecting to Wi-Fi ® and connecting to the myQ ® App. Flashing Blue and GreenConnecting to Wi-Fi and connecting to the myQ ® App. Solid GreenConnected to the myQ ® App. Flashing PurpleReceiving fi rmware updates. Solid RedCamera thermal error state when the camera reaches high heat 60 °C temperature and cools down. Masking Tape 4. Lower the camera and unplug the wire harness. Decorative Ring 9. Locate the notch in the camera’s opener and pull down. Adjust the camera position as needed. Tools: • Philips Screwdriver • Ladder • Masking Tape (optional) Hardware: • Screw Qty. (3) • Decorative Ring • Camera NOTICE: This device complies with part 15 of the FCC rules and Innovation, Science and Economic Development Canada licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/bystanders and device. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. REVIEW COPY Anillo decorativo Para evitar daños a la cámara, cierre el lente de la cámara cuando la reemplace, y sosténgala en el lugar al retirar los herrajes de seguridad. NO toque el tablero lógico de la cámara durante la instalación. Use SIEMPRE guantes protectores y protección para la vista al cambiar la batería o al trabajar cerca del compartimiento de la batería. Introducción Instalación JUEGO DE SERVICIO DE LA CÁMARA DE REPUESTO Modelo 041-0041 Se puede acceder a la cámara desde el lado inferior del abre-puertas. Una vez instalada la cámara nueva, use la aplicación myQ ® para conectar la cámara a su cuenta myQ ® . 1. Desconecte la alimentación eléctrica al abre-puertas de garaje y retire la batería de reserva, si la usara. Para evitar posibles LESIONES GRAVES o la MUERTE: • Desconecte TOTALMENTE la corriente eléctrica y de la batería ANTES de realizar CUALQUIER servicio o mantenimiento. ADVERTENCIA: Este producto puede exponerle a productos químicos (incluido el plomo), que a consideración del estado de California causan cáncer, defectos congénitos u otros daños reproductivos. Para más información, visite www.P65Warnings.ca.gov 2. Retire el anillo decorativo en la parte inferior del abre- puertas. 3. Desatornille la cámara lentamente de la carcasa del abre-puertas. SUGERENCIA: Use cinta adhesiva de papel para sostener la cámara en el lugar mientras retira los tornillos. 5. Enchufe la cámara nueva. 6. Alinee y atornille la cámara nueva en la carcasa del abre- puertas. 7. Coloque el anillo decorativo nuevo. 8. Vuelva a conectar la alimentación eléctrica y la batería, si la usara. 10. Siga las instrucciones de la aplicación myQ ® para agr…

Text truncated - open the document above for the full version.

Date: February 17, 2022 We, The Chamberlain Group Inc. declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: HBW-GDOCAM3 If you have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- Barbara Kelkhoff / Regulatory Engineering Manager The Chamberlain Group Inc. Tel: 630-99-6306 Fax: 630-516-6863 E-mail: [email protected]

Date: 2022-02-17 FCC ID: HBW-GDOCAM3 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Barbara Kelkhoff / Regulatory Engineering Manager The Chamberlain Group Inc. Tel: 630-99-6306 Fax: 630-516-6863 E-mail: [email protected]

Date: 2022-02-17 FCC ID: HBW-GDOCAM3 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: The Chamberlain Group Inc. hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on The Chamberlain Group Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Barbara Kelkhoff / Regulatory Engineering Manager The Chamberlain Group Inc. Tel: 630-99-6306 Fax: 630-516-6863 E-mail: [email protected]

Reference No.: BIBJ-WTW-P22010311_EXT Page 1 / 4 CONSTRUCTION PHOTOS OF EUT Brand ：Chamberlain ／ Model：GDOCAM3 Reference No.: BIBJ-WTW-P22010311_EXT Page 2 / 4 Reference No.: BIBJ-WTW-P22010311_EXT Page 3 / 4 Reference No.: BIBJ-WTW-P22010311_EXT Page 4 / 4

2530A2007L-A05FX 1/1 see notes see notes DC-2007 DC-2007 (CHAMBERLAIN HAWKEYE 3.0) PRODUCT LABEL, HAWKEYE 3.0 2022/02/10 Teresa Model: GDOCAM3 FCC ID: HBW-GDOCAM3 IC: 2666A-GDOCAM3 CHAMBERLAIN GROUP, INC. OAK BROOK, IL 60523 Country of Origin: China Input/Maxpower :5V 1.5Amp/7.5W May be patent protected Peut être protégé par brevet Podria estar protegido por derechos patente See www.chamberlain.com/patents Label Position 1. Material: 50 ounce White PET Label 2. Color: Black 3. Size:54(L) x 18(W) mm 4. Finish: Glossy 5. Glue: Permanent glue 6. Tolerance: +0.05/-0.05mm 7. Unit:mm Notes: 100% 54 18 Model: GDOCAM3 FCC ID: HBW-GDOCAM3 IC: 2666A-GDOCAM3 CHAMBERLAIN GROUP, INC. OAK BROOK, IL 60523 Country of Origin: China Input/Maxpower :5V 1.5Amp/7.5W May be patent protected Peut être protégé par brevet Podria estar protegido por derechos patente See www.chamberlain.com/patents ESL Proto Factory printing Font: Arial, 5pt DVT : ESL2 Proto PVT : MSL Proto MP: MM/YEAR

Reference No.: BIBJ-WTW-P22010311_INT Page 1 / 9 CONSTRUCTION PHOTOS OF EUT Brand ：Chamberlain ／ Model：GDOCAM3 Reference No.: BIBJ-WTW-P22010311_INT Page 2 / 9 Reference No.: BIBJ-WTW-P22010311_INT Page 3 / 9 Reference No.: BIBJ-WTW-P22010311_INT Page 4 / 9 Reference No.: BIBJ-WTW-P22010311_INT Page 5 / 9 Reference No.: BIBJ-WTW-P22010311_INT Page 6 / 9 Reference No.: BIBJ-WTW-P22010311_INT Page 7 / 9 Reference No.: BIBJ-WTW-P22010311_INT Page 8 / 9 Reference No.: BIBJ-WTW-P22010311_INT Page 9 / 9

Report No.: SABIBJ-WTW-P22010311 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SABIBJ-WTW-P22010311 FCC ID: HBW-GDOCAM3 Test Model: GDOCAM3 Received Date: Jan. 10, 2022 Date of Evaluation: Feb. 10, 2022 Issued Date: Feb. 17, 2022 Applicant: The Chamberlain Group Inc. Address: 300 Windsor Drive Oak Brook, IL 60523 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SABIBJ-WTW-P22010311 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Calculation Result of Maximum Conducted Power ............................................................................. 6 Report No.: SABIBJ-WTW-P22010311 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SABIBJ-WTW-P22010311 Original Release Feb. 17, 2022 Report No.: SABIBJ-WTW-P22010311 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Hawkeye 3 Camera Module Brand: Chamberlain Test Model: GDOCAM3 Sample Status: Engineering Sample Applicant: The Chamberlain Group Inc. Date of Evaluation: Feb. 10, 2022 Standards: FCC Part 2 (Section 2.1091) References Test Guidance : KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Feb. 17, 2022 Gina Liu / Specialist Approved by : , Date: Feb. 17, 2022 Jeremy Lin / Project Engineer Report No.: SABIBJ-WTW-P22010311 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz ; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SABIBJ-WTW-P22010311 Page No. 6 / 6 Report Format Version: 6.1.1 2.4 Calculation Result of Maximum Conducted Power Band Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) WLAN 2412-2462 20.07 1.61 20 0.029 1.00 5180-5240 18.97 1.89 20 0.024 1.00 5745-5825 18.21 1.93 20 0.021 1.00 BT 2402-2480 7.10 1.61 20 0.001 1.00 Note: 1. The device WiFi 2.4GHz, 5GHz and BT modes doesn't support simultaneously transmit. 2. Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. 3. The above Antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible --- END ---

Report No.: RFBIBJ-WTW-P22010311 Page No. 1 / 37 Report Format Version: 6.1.1 FCC Test Report Report No.: RFBIBJ-WTW-P22010311 FCC ID: HBW-GDOCAM3 Test Model: GDOCAM3 Received Date: Jan. 10, 2022 Test Date: Jan. 18 ~ Jan. 25, 2022 Issued Date: Feb. 17, 2022 Applicant: The Chamberlain Group Inc. Address: 300 Windsor Drive Oak Brook, IL 60523 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan Test Location (2): No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan FCC Registration / Designation Number: 788550 / TW0003 281270 / TW0032 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RFBIBJ-WTW-P22010311 Page No. 2 / 37 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Modification Record .............................................................................................................................. 6 3 General Information ................................................................................................................................... 7 3.1 General Description of EUT .................................................................................................................. 7 3.2 Description of Test Modes ..................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 9 3.3 Duty Cycle of Test Signal .................................................................................................................... 10 3.4 Description of Support Units ................................................................................................................ 11 3.4.1 Configuration of System under Test .......................................................................................... 11 3.5 General Description of Applied Standards and References ................................................................ 11 4 Test Types and Results ............................................................................................................................ 12 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 12 4.1.2 Test Instruments ....................................................................................................................... 13 4.1.3 Test Procedures ........................................................................................................................ 14 4.1.4 Deviation from Test Standard ................................................................................................... 14 4.1.5 Test Set Up ............................................................................................................................... 15 4.1.6 EUT Operating Conditions ........................................................................................................ 16 4.1.7 Test Results .............................................................................................................................. 17 4.2 Conducted Emission Measurement .................................................................................................... 22 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 22 4.2.2 Test Instruments ....................................................................................................................... 22 4.2.3 Test Procedures ........................................................................................................................ 22 4.2.4 Deviation from Test Standard ..........................................................................................…

Text truncated - open the document above for the full version.

Report No.: RFBIBJ-WTW-P22010311-1 Page No. 1 / 53 Report Format Version: 6.1.1 FCC Test Report Report No.: RFBIBJ-WTW-P22010311-1 FCC ID: HBW-GDOCAM3 Test Model: GDOCAM3 Received Date: Jan. 10, 2022 Test Date: Jan. 14 ~ Jan. 24, 2022 Issued Date: Feb. 17, 2022 Applicant: The Chamberlain Group Inc. Address: 300 Windsor Drive Oak Brook, IL 60523 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan Test Location (2): No. 70, Wenming Rd., Guishan Dist., Taoyuan City 333, Taiwan FCC Registration / Designation Number: 788550 / TW0003 281270 / TW0032 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RFBIBJ-WTW-P22010311-1 Page No. 2 / 53 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Modification Record .............................................................................................................................. 6 3 General Information ................................................................................................................................... 7 3.1 General Description of EUT .................................................................................................................. 7 3.2 Description of Test Modes ..................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 9 3.3 Duty Cycle of Test Signal ..................................................................................................................... 11 3.4 Description of Support Units ............................................................................................................... 12 3.4.1 Configuration of System under Test ......................................................................................... 12 3.5 General Description of Applied Standards and References ............................................................... 12 4 Test Types and Results ............................................................................................................................ 13 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 13 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 13 4.1.2 Test Instruments ....................................................................................................................... 14 4.1.3 Test Procedures ........................................................................................................................ 15 4.1.4 Deviation from Test Standard ................................................................................................... 15 4.1.5 Test Set Up ............................................................................................................................... 16 4.1.6 EUT Operating Conditions ........................................................................................................ 17 4.1.7 Test Results .............................................................................................................................. 18 4.2 Conducted Emission Measurement .................................................................................................... 29 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 29 4.2.2 Test Instruments ....................................................................................................................... 29 4.2.3 Test Procedures ........................................................................................................................ 30 4.2.4 Deviation from Test Standard ......................................................................................…

Text truncated - open the document above for the full version.

Reference No.: RFBIBJ-WTW-P22010311_TSup 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Reference No.: RFBIBJ-WTW-P22010311_TSup 2 RADIATED EMISSION TEST BELOW 1GHz (X-Plane) Reference No.: RFBIBJ-WTW-P22010311_TSup 3 RADIATED EMISSION TEST ABOVE 1GHz (X-Plane)