HBW1341Remote control transmitter

"Smart" (learn) Button Indicator Light KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 © 1998, Chamberlain Group Inc. 114A2335All Rights ReservedPrinted in Mexico Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the wall push buttons or remote controls. A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door clearly, it is free of obstructions, and is properly adjusted. WARNING Figure 2 The Security:remote control works only with door openers and light controls having an orange "Smart" button and a yellow indicator light. Programming instructions are described and illustrated below. The additional push buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those accessories.) SECURITY:GARAGE DOOR OPENERS To Program the Opener to Accept the Remote Control Code Select a remote control push button to operate the opener. The largebutton is recommended for use with a garage door opener. 1. Press and hold the selected remote control push button. See Figure 1. 2. Press and release the “Smart” (learn) button on the opener panel. See Figure 2. The indicator light on the panel will begin to blink and the opener lights will flash once. 3. Release the remote push button. Now the opener will operate when that remote control button is pressed. Test it by pressing the remote button to see that the door goes up and down. Adding a remote can also be done from the door control, as follows: 1. With the door closed, press and hold a remote push button. 2. Press and hold the Light button on the door control. 3. Press and hold the door control push bar. 4. After the opener lights flash, release all buttons. Test by pressing the remote push button. To Erase All Remote Control Codes Press and hold the “Smart” button on the opener panel until the indicator light turns off (about 6 seconds). All transmitter codes are now erased. Then follow the steps above to re- program each remote control. To Control the Opener Lights With Security:transmitters, a remote push button can be programmed to operate the opener lights without opening the door. 1. With the door closed, press and hold the remote button that you want to control the light. 2. Press and hold the Light button on the door control. 3. Press and hold the Lock button on the door control. 4. After the opener lights flash, release all buttons. Test by pressing the remote push button. The opener lights should turn on or off but the door should not move. Open/Close/Stop Operation Your Security:remote control can be programmed to operate one door using all 3 buttons: the large button will only open the door, the middle button will only close the door, and the third button will stop the door’s movement. You may set up this feature as follows: 1. With the door closed, press and hold the large remote push button. 2. Press and hold the Lock button on the door control. 3. Press and hold the door control push bar. When the opener lights flash, release all buttons. Test by pressing the large (Open) button on the remote. The door should open. Press it again while the door is open and nothing should happen. Press the middle (Close) button and the door should close. Press the third (Stop) button while the door is moving and it should stop immediately. Open Close Stop NOTICE: To comply with FCC rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Figure 1 SECURITY: Remote Control The Remote Control Battery The lithium battery should produce power for up to 5 years. To replace battery, pry open case vith visor clip or screwdriver, as shown. Insert battery positive side up (+). Dispose of old battery properly. Keep batteries away from small children. If swallowed, promptly notify doctor. WARNING Replacement Parts 433MHz SECURITY:remote case (circuit board not included) – 41A5056-3; 3V2032 Lithium battery – 10A20; Visor clip – 29B137 FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 SECURITY: Garage Door Opener 433MHz 3 Channel Remote Control Les enfants qui utilisent ou qui jouent avec un ouvre-porte de garage risquent de se blesser et de blesser les autres. La porte risque de se fermer et de causer de graves blessures, voire la mort. Ne pas permettre aux enfants d’utiliser les télécommandes ou les boutons-poussoirs au mur. Une porte de garage en mouvement peut blesser ou tuer la personne qui se trouve dessous. N’actionner l’ouvre-porte de garage que si l’on peut bien voir la porte, s’il n’y a pas d’obstruction et si elle est bien réglée. AVERTISSEMENTAVERTISSEMENT AVIS: Conformément aux règles de la FCC/IC, il est interdit de régler ou de modifier ce récepteur et/ou émetteur, sauf pour modifier le code ou pour remplacer la pile. IL N’EXISTE AUCUNE AUTRE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. ©1998, The Chamberlain Group, Inc 114A2335Tous droits réservés.Imprimé au Mexique Pièces de rechange 433MHz Télécommande SECURITY:(sans fil) – 41A5056-3; Pile au lithium 3V2032 – 10A20; Pince de pare-soleil – 29B137 POUR LE SERVICE, PRIÈRE DE COMPOSER NOTRE NUMÉRO SANS FRAIS 1-800-654-4736 La télécommande SECURITY: fonctionne uniquement avec les ouvre-portes et commandes d’éclairage possédant un bouton “Smart” orange et un témoin lumineux jaune. Des instructions de programmation sont décrites et illustrées ci- après. Les boutons-poussoirs supplémentaires peuvent également actionner d’autres ouvre-portes de garage et/ou commandes d’éclairage. (Les instructions pour la programmation de l’éclairage sont fournies avec ces accessoires.) OUVRE-PORTES DE GARAGE SECURITY: Pour programmer l’ouvre-porte pour accepter le code de télécommande Sélectionner un bouton-poussoir de télécommande p…

Text truncated - open the document above for the full version.

"Smart" (learn) Button Indicator Light KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 © 1998, Chamberlain Group Inc. 114A2335All Rights ReservedPrinted in Mexico Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the wall push buttons or remote controls. A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door clearly, it is free of obstructions, and is properly adjusted. WARNING Figure 2 The Security:remote control works only with door openers and light controls having an orange "Smart" button and a yellow indicator light. Programming instructions are described and illustrated below. The additional push buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those accessories.) SECURITY:GARAGE DOOR OPENERS To Program the Opener to Accept the Remote Control Code Select a remote control push button to operate the opener. The largebutton is recommended for use with a garage door opener. 1. Press and hold the selected remote control push button. See Figure 1. 2. Press and release the “Smart” (learn) button on the opener panel. See Figure 2. The indicator light on the panel will begin to blink and the opener lights will flash once. 3. Release the remote push button. Now the opener will operate when that remote control button is pressed. Test it by pressing the remote button to see that the door goes up and down. Adding a remote can also be done from the door control, as follows: 1. With the door closed, press and hold a remote push button. 2. Press and hold the Light button on the door control. 3. Press and hold the door control push bar. 4. After the opener lights flash, release all buttons. Test by pressing the remote push button. To Erase All Remote Control Codes Press and hold the “Smart” button on the opener panel until the indicator light turns off (about 6 seconds). All transmitter codes are now erased. Then follow the steps above to re- program each remote control. To Control the Opener Lights With Security:transmitters, a remote push button can be programmed to operate the opener lights without opening the door. 1. With the door closed, press and hold the remote button that you want to control the light. 2. Press and hold the Light button on the door control. 3. Press and hold the Lock button on the door control. 4. After the opener lights flash, release all buttons. Test by pressing the remote push button. The opener lights should turn on or off but the door should not move. Open/Close/Stop Operation Your Security:remote control can be programmed to operate one door using all 3 buttons: the large button will only open the door, the middle button will only close the door, and the third button will stop the door’s movement. You may set up this feature as follows: 1. With the door closed, press and hold the large remote push button. 2. Press and hold the Lock button on the door control. 3. Press and hold the door control push bar. When the opener lights flash, release all buttons. Test by pressing the large (Open) button on the remote. The door should open. Press it again while the door is open and nothing should happen. Press the middle (Close) button and the door should close. Press the third (Stop) button while the door is moving and it should stop immediately. Open Close Stop NOTICE: To comply with FCC rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Figure 1 SECURITY: Remote Control The Remote Control Battery The lithium battery should produce power for up to 5 years. To replace battery, pry open case vith visor clip or screwdriver, as shown. Insert battery positive side up (+). Dispose of old battery properly. Keep batteries away from small children. If swallowed, promptly notify doctor. WARNING Replacement Parts 433MHz SECURITY:remote case (circuit board not included) – 41A5056-3; 3V2032 Lithium battery – 10A20; Visor clip – 29B137 FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 SECURITY: Garage Door Opener 433MHz 3 Channel Remote Control Les enfants qui utilisent ou qui jouent avec un ouvre-porte de garage risquent de se blesser et de blesser les autres. La porte risque de se fermer et de causer de graves blessures, voire la mort. Ne pas permettre aux enfants d’utiliser les télécommandes ou les boutons-poussoirs au mur. Une porte de garage en mouvement peut blesser ou tuer la personne qui se trouve dessous. N’actionner l’ouvre-porte de garage que si l’on peut bien voir la porte, s’il n’y a pas d’obstruction et si elle est bien réglée. AVERTISSEMENTAVERTISSEMENT AVIS: Conformément aux règles de la FCC/IC, il est interdit de régler ou de modifier ce récepteur et/ou émetteur, sauf pour modifier le code ou pour remplacer la pile. IL N’EXISTE AUCUNE AUTRE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. ©1998, The Chamberlain Group, Inc 114A2335Tous droits réservés.Imprimé au Mexique Pièces de rechange 433MHz Télécommande SECURITY:(sans fil) – 41A5056-3; Pile au lithium 3V2032 – 10A20; Pince de pare-soleil – 29B137 POUR LE SERVICE, PRIÈRE DE COMPOSER NOTRE NUMÉRO SANS FRAIS 1-800-654-4736 La télécommande SECURITY: fonctionne uniquement avec les ouvre-portes et commandes d’éclairage possédant un bouton “Smart” orange et un témoin lumineux jaune. Des instructions de programmation sont décrites et illustrées ci- après. Les boutons-poussoirs supplémentaires peuvent également actionner d’autres ouvre-portes de garage et/ou commandes d’éclairage. (Les instructions pour la programmation de l’éclairage sont fournies avec ces accessoires.) OUVRE-PORTES DE GARAGE SECURITY: Pour programmer l’ouvre-porte pour accepter le code de télécommande Sélectionner un bouton-poussoir de télécommande p…

Text truncated - open the document above for the full version.

845 Larch Ave. Elmhurst, IL 60126 phone 630.993.6306 fax 630.530.6140 email: [email protected] August 20, 1998 Federal Communications Commission EQUIPMENT APPROVAL SERVICES PO Box 358315 Pittsburgh, PA 15251-5315 Re: Request for Certification Enclosed is an application, fee in the amount of $895, and exhibits for Certification of a Remote Control Transmitter, Model 1A5235. The final instruction sheet is not available at this time, so I have included a typical instruction sheet indicating the FCC statement and important information. The FCC ID of this model, upon certification, will be HBW1341. We would appreciate your prompt attention to the submittal. Sincerely, THE CHAMBERLAIN GROUP, INC. Barbara P. Kelkhoff Manager, Product Safety LIST OF EXHIBITS 3 FUNCTION, REMOTE CONTROL TRANSMITTER MODEL 1A5235 1. Expository Statement 2. Theory of Operation 3. Schematic 4. Photographs 5. FCC Label Drawing 6. Operating Instructions 7. Test Report EXPOSITORY STATEMENT 3 FUNCTION, REMOTE CONTROL TRANSMITTER MODEL 1A5235 1. Since the final instruction sheet is not available at this time, a marked-up typical version has been included. The instructions include statements required to assure compliance with the Commission's Rules; Part 15. 2. Labeling is in accordance with the Commission's labeling requirements, Parts 2 and 15, Section 15.19. 3. This transmitter is intended for use with the certified receivers of our manufacture only. 4. The transmitter is equipped with an automatically releasing push-button switch. Transmission is terminated upon release of the push-button. 5. The 1A5235 is factory set to 433 ± 0.1% MHz. It is not intended to be readjusted in the field, and specific instruction prohibiting tampering are provided to the user. 6. Test data for the Model 1A5235 is part of this submission. No emissions were detected in the forbidden bands below 1.0 GHz. Certified by: Barbara P. Kelkhoff Manager, Product Safety THEORY OF OPERATION AND CIRCUIT DESCRIPTION MODEL 1A5235 3 FUNCTION, REMOTE CONTROL TRANSMITTER (Please refer to enclosed schematic drawing: 195D1341A) The 1A5235 transmitter consists of a low power RF oscillator (Q2 and associated components), a digital encoder (U1 and related components), and on/off switches. The RF oscillator, Q2, is of the grounded base type. C2, C3, C5, C8, and the copper loop, L2, set the center frequency of the oscillator at 433 MHz. C4 and C7, with the internal capacitance of Q2, establish feedback levels and harmonic suppression. R1, R2 and R5 establish dc operating conditions on Q2 and help improve temperature stability. U1 and related components generate a digital code. This code is used in the companion receiver to identify a particular transmitter or function. The 3V battery circuit is equipped with an automatically releasing (normally off) push-button switches that supply voltage to U1 when SW1, SW2 or SW3 are depressed. U1 contains a voltage switcher circuit that increases the 3V to 9V . A square wave output is applied to driver Q1 through R4. L1, D1 and C1 boost and filter the voltage to 9V. This is applied to Q2, regulated to 9V by U1, and monitored through pin 5. SW1-SW3 and U1 provide three input functions. The digital signal is randomly programmed and the code is stored within U1. 1. EXPOSITORY STATEMENT 2. THEORY OF OPERATION 3. SCHEMATIC 4. PHOTOGRAPHS 5. FCC LABEL DRAWING 6. OPERATING INSTRUCTIONS 7. TEST REPORT

845 Larch Ave. Elmhurst, IL 60126 phone 630.993.6306 fax 630.530.6140 email: [email protected] August 20, 1998 Federal Communications Commission EQUIPMENT APPROVAL SERVICES PO Box 358315 Pittsburgh, PA 15251-5315 Re: Request for Certification Enclosed is an application, fee in the amount of $895, and exhibits for Certification of a Remote Control Transmitter, Model 1A5235. The final instruction sheet is not available at this time, so I have included a typical instruction sheet indicating the FCC statement and important information. The FCC ID of this model, upon certification, will be HBW1341. We would appreciate your prompt attention to the submittal. Sincerely, THE CHAMBERLAIN GROUP, INC. Barbara P. Kelkhoff Manager, Product Safety LIST OF EXHIBITS 3 FUNCTION, REMOTE CONTROL TRANSMITTER MODEL 1A5235 1. Expository Statement 2. Theory of Operation 3. Schematic 4. Photographs 5. FCC Label Drawing 6. Operating Instructions 7. Test Report EXPOSITORY STATEMENT 3 FUNCTION, REMOTE CONTROL TRANSMITTER MODEL 1A5235 1. Since the final instruction sheet is not available at this time, a marked-up typical version has been included. The instructions include statements required to assure compliance with the Commission's Rules; Part 15. 2. Labeling is in accordance with the Commission's labeling requirements, Parts 2 and 15, Section 15.19. 3. This transmitter is intended for use with the certified receivers of our manufacture only. 4. The transmitter is equipped with an automatically releasing push-button switch. Transmission is terminated upon release of the push-button. 5. The 1A5235 is factory set to 433 ± 0.1% MHz. It is not intended to be readjusted in the field, and specific instruction prohibiting tampering are provided to the user. 6. Test data for the Model 1A5235 is part of this submission. No emissions were detected in the forbidden bands below 1.0 GHz. Certified by: Barbara P. Kelkhoff Manager, Product Safety THEORY OF OPERATION AND CIRCUIT DESCRIPTION MODEL 1A5235 3 FUNCTION, REMOTE CONTROL TRANSMITTER (Please refer to enclosed schematic drawing: 195D1341A) The 1A5235 transmitter consists of a low power RF oscillator (Q2 and associated components), a digital encoder (U1 and related components), and on/off switches. The RF oscillator, Q2, is of the grounded base type. C2, C3, C5, C8, and the copper loop, L2, set the center frequency of the oscillator at 433 MHz. C4 and C7, with the internal capacitance of Q2, establish feedback levels and harmonic suppression. R1, R2 and R5 establish dc operating conditions on Q2 and help improve temperature stability. U1 and related components generate a digital code. This code is used in the companion receiver to identify a particular transmitter or function. The 3V battery circuit is equipped with an automatically releasing (normally off) push-button switches that supply voltage to U1 when SW1, SW2 or SW3 are depressed. U1 contains a voltage switcher circuit that increases the 3V to 9V . A square wave output is applied to driver Q1 through R4. L1, D1 and C1 boost and filter the voltage to 9V. This is applied to Q2, regulated to 9V by U1, and monitored through pin 5. SW1-SW3 and U1 provide three input functions. The digital signal is randomly programmed and the code is stored within U1. 1. EXPOSITORY STATEMENT 2. THEORY OF OPERATION 3. SCHEMATIC 4. PHOTOGRAPHS 5. FCC LABEL DRAWING 6. OPERATING INSTRUCTIONS 7. TEST REPORT

1A5235 TRANSMITTER

1A5235 TRANSMITTER

1A5235 TRANSMITTER

1A5235 TRANSMITTER

1A5235 TRANSMITTER

1A5235 TRANSMITTER

%PDF-1.2 ̋%âãÏÓ ̋ ̋6 0 obj ̋<< ̋/Length 7 0 R ̋/Filter /LZWDecode ̋>> ̋stream ̋ ̆Ãqî ŒD ̄ ̈D(Õ ̊• ̊"1•‘-•7•‹†CÒ6.• ̊ °ˆØÊ5! $ˆ ̃dq&JCÔ²]••L¦Yh678™J¤3Ñ ̈Âh1‚ÊetJ0º •Œ†ó`m•™ÆFÕIü‚CY•VçμÙÈegG,rù=šÐ4μK¦•ñj ̈1ŒF£– •^3•Çèp‚œBƒÏ‡#Qpæ ̋3•Ð¤P ̃Äl.•G2•)îW/™ ̈ .Ö<^7¢°×4 ̧ê†F—„ÃA ÐØõz¡ `²8NÖÊ4•@†cq-Lb3ÏŒx±Ñ†^9H•B ̧•á`Ç •@†# ϙԕñàu¾ ̈ ‰Æñ ëc=ÀÒ·Ö†ú}}ÍÌç½Híw;Ü>Œ• §* ́»úêºèKÌ9J›øÄ ́‹|²!£êîÁ°{n“=Ð#`Þ¤Á«Öö²hJØËBíx•Â§Ápp 10ó•‚ ̧ŠÛxâ®ÑŠ©•5! ̧hš/±:•÷EJ„dÊC•• ̈ ̈¥j,M• M“•œ†ñR¾•J!²8ÞJ•’Ì•§kˆ•î Pô¶Œμ‰ìPû7,{²•Ë ìÒ ̈H ̋Š ̈•8-4àËÎIìé(μŠŠ ̄ÁËóst ̈Mt ̄P±ŠxfÚ¶Må• ̇3Ò ̋ƕɬ{- I$”¢ ̇Çщâ]DÓ‰3e3Gვä*•«¹• ̧•;ÖÊÎÌèr5zi2²•›•õÕT ̆Z•U ́zªLáª3T8 ́šk,XÖ ̃Ö•Ê, ̄ôœ×p £/'0•jæYTô¿fÙ ́...»b$Š”ÞöJ+-•sPn•iA¬o•••ÝöògeQAÍÓ@,òÛ}6Õ"}•ÎÈÛ/1QÑ& ÜÇ©›ÖàÚ«- >â•Þ%[« ́Æ•-Å ́›3•#–M–Êcñ]¬½5P’á“ÚI s•d7•jÎä¹Ç=‘zöÂQ#yœå ̊Ú ̄ÐOMD¬³ ̈••±£gyì{ 0 ́– x§c•*μ¦ê•f™¤iSšbÌ/zNÁ ̄BM ̇¥§NzÞϬç•~•®lyþÝ1mq#;±aZìÊo ̋Þ...±ÖP– é±hÛ#-PˆÈ`çáÇ_ó‘h ́<ŒrŠ@píO4ÌPÉ$-·íy5•Ñðh•¼’Ú»ÿV¶[}/WÔoÚM]¦á+ôIVéÛu{× k vé'...Ý«×]r'Þ?— GyÞˆ ̧ö<r߉ÕúW±ùÛ•½CàŠÆÝ•ôòŠ|}ŸÍŒë ̧ºk¿ð ̧•v³}>bø³s•Õ•:MýÌ¢ªØ‘ŒPmIe•Uâ] # ́$...ÔÔ¿ ä ́î•£HZè„©••*ÍÉs** ̈‰{B¾ š“"$n• ̧e•ØÊ’|7fR•¶ejX\á1~†\•C•¾ ́•Œ,l¥î•+„| ̃L„;i Õ•™ ̄ªØb#88e„½ƒ•”ââ,-‰±=ÐÄ ̊e •C?P°I”;...šø¡£ŒxÅþ ªâ ̧ ̊ÊŠ9K:3Æ ̃Á ̋ä_†qÂ/FF<@¡“§$ÆiˆC'p £Ü•&ièGcÂõ]ÄhR ̈6 ̋?ÅÛ#•ÂJ†¦...Z$8$„ hætà6ó*ÕÒ<LQ݈™I1%%,?XD ̋I±ç ̆%–••†R¹·É•e&Lû¼’ò²\8 ̈ (X18P® u¶efÌ#ѹú•£@–Bw-±R ̄äÔeÛÚ_ ̇•YúEFÉ ̋"s kÓ1ôLç¾Úü.›ÓB!°ÕRüÑQLVK• ¹)• ́Õ\êš.Ή ̃Ç™Ôã‘rVe ̃( ̋^Ð<„Gè8³P™àG ̈= sj²ƒ•š•Ì(-• ÄÑòP²¾¬•[ˆ¢•ZÑi¡Fˆú=¢ ̆¹*«âÑ`×3- (ð½Í8|G~¦Ëy“ŠY?RùÛ`«šI§ª„Ý)Js ̈íúNzg seŒSÄ“0ª*gE($Ê¢£•òÑW•Ü –f•Ÿ<d¢öš ̄ÙPïæ± ̄ ̧)[• ̧x°þ±!`pF]5fz¦F¼TêêT+» -ëF»•2Æ Œ½hcSŠÃ™s`dLd›tF0²Ù ̆½¡ªÌ/ƒçd]™&hæDÏ ̄É ́eì ̆†tUlÇØ•çZÖÑó$Ó>É›c#lÝ3N9M¼›•|É¥` 'ÕÂÀ$Ö•q •@·Õí ́@÷EnBvvQ ̊\ÒŸaè ºî‰eJÛ›Hm] ̈¹2ùæÖ{eˆ ̄-̼Ï0öLâ¾ h亽³Š|Pö œŸEñˆ¦•í_š,ÛU•~¾•™\à•Q>eQ ̧¿ ̧ Ä ]•oÓw%F²ÿ`ƒ"ï°••sˆ-÷Εe...ðê•Tmó ?H ̄Óðæ•...ñA»×Øæ¼0+Õ} •o1Óé ̄Ó!Wúð`âMŠŒcñs®ÄÒä+xªF'Hî:9âÆù/¢Q ̧FG(N[PÝñØ9+XnAštþ—-½P¾¹.î¡ é’Г•Ëù¡jÊK·ƒ¬ãô4>NÖ...̓Nê]P‹¦§•›Œâ^ªmÏåE•Ì¬êzËDÄÏ, ̈“ ôJ¬ÐðmcÓÉ;cê•Â;μâ -ƒ]1ËÄtGñ.Vê•‹ ̈á¡š;iÍ ̃©bU¦–•Z“ù_Q ̃ÅW£Yš•ÏÕîCÕ3» ̇Œ®"¥PŸ3Wˆ«®ëF½UŠÃLQËØÖ Š¾SM“(½9•“¼·•Gl§ ¹¶#b‹pS•wX-Ä›÷ ̇ÑÜ{sp°MO1u±š“¶Kx•μ•2Lì'”oS •ˆÚd•#OI•>NÕ‰ŠM7”¬Ì•nç9Õ†ëÝ*¿ ̃3ý «ø•03\]#¤ŠÑ”÷ô³Ö9:b-Ô!• ̧î ̇2 [|ðƒZ‘wÎk2•U§Í•Z’!‰*1ü{šå%_DLîÔãlª•œî7e•:æX<s ¿þOb\•)ãiEø±Òó(Ömeˆ ̋hÐ,,ç{:¹ë ̇Ôr©Þ >±Ñ» ́•ë *¼õ¶º°»eNìÊó ̧Ä^ªHQ/=u%rDzäVô8w ̄kkN¶e쬊àÇ Êo)AÞª©hnq•G ̆...ÞL§•• ׺³‹›,Íõòï{Ê=ùNÕà;bGîûŸÓ65••»×„H• ̊âQe•â<¢ãö÷¡woog ̃•Ô£ ™O®o( 5Þ»zÔïß ̈Ô^O{ÃPÇÀô©Âª¹ oî®o8y§è_ÿ3ãS„Oø ̇2cü ̄)ù< ̈ÇûþÛá ́ÿ5ÃeϪû-âe`6MHÖÚX- „Ée`„ÎþÆBšhòGð`0*hþ®•d*„hïôH¤v%Mèÿð•#°•— HшdvÖÄæÁ(x...|WCXGj0OEt4DA„ôÇμ ̄ìÞ. ̈ÿ ̃ ̄¼Kè@μ•N~±e·%1C/0+ ̄:fß ́¢V8 ̄ÈÆ° ̃ •`d¿`°„LGpœ-ª ́è QÈ<HKfŠ§Ðî£BDäQФ3Eš{P£ „<Ð(2ÞÐÏ ŠÃ %R·è) Îà°CH¥RÇåì7 ̄ú7IjeͶXM•4ˆ:Ó‘ ́•¢|°$å•è|#l&îè%Ñ é• ° ̧Jˆá •ìQp 5D:ð•&4‡-. R} ̈•†•WN ̊uñ H è+±• ŒG•+¤N•"- iîZÞae8û‚ ̧³mÛ•ðÒÚ ̄Û•íN(;ê[•ÍÍ••~ŒÑ9•«•S+ñs•¢×•±¢Á•`St_‹\ÛÊÍ‘ ̧WJÑ•±DsÄé •É=•°ê÷Ï`eÑ.O•ó•ñ–g •sÄ Uf~N¥• ̈ª9 ̊h5© ̃gñöUé^½’•5¥Þ–•`çr!’ ̋2•'!•*êG.› ̄Ô¬ç$ ̇Ë"B ”ië23B¤rê"*+Tˆ N]²Frð²Ïkz3®ÆÌR5&"Ñ•c m%(•¾P©$Cμ$‡æOÑ+%...*PŒºrò’× ...&¤Ô›Òi&"¢YPÙ%’Rkïμ'-e+R> 2«(ò ̊šR¤2’•)ÌÁ,âg&rÍ#... ̊Ïòi, ̄Ö›#‘'Í ̄,Ò‹'ä¬&MR‡/d«- òÅ"2•-‰.}e ̊ÃS`sÊ*s’ø¶Ê+*å ` ̇V} ̊‚†M2ÂÛ ̋,øÎDß •:} b~Ó( ̆« ̋ÓLÿÆ]4, ̇ÿ3V¤‹ˆ~3,i ̄ ̇4Œh‹’®É* ‹ ̆ømÌ‘ ̇s{ ȱ70ôc3k•ÇI6'V7 ̇é5©á7F#m× Þi•R4“B-m†ús8¤ˆz ̃“f*BT®s ‡ƒG-‚V*MÆÌ/3¶+³Ð51³<•Êuèx...Q ?/ •ÓÀ±ÑÀÓ‚¥$3܇Š ̃-(o@æ\ ́ˆÌö±v_T•@ ̃U4(pàÓ52³Â~Ò ̧•¤<G÷p ̧lÊN•jtôFQoûD'sDé:5‡ m î‡*éCn•V“ÅFƒZ½Ç’³ÃZê‹BÌJ•³ •éèØ°äÂçmº{N5® 'êkÈjBT6C6±‡Je9FÔ5HcZ¢(ô¼NyGo,V ̈ƒF•ÉKr»<ªÞμ... ̊çTÄ•ªb_”?N- ¿LÜÑQ•b ÞLæ ̊ef<H¤Ú¿S5;tùPFÝÍF|P=NªIPí}O³R¥Dv~0P4~Œ OG©:1TÓÍ^ÀHðÓÅÓS DKéŒ|U*;¦7R‰SUGIQÉ•SfÃTm ̄k&•Þ‚sPQcºc#••u 6•ªÒU ̄¹¬aTÇþl$þWÈ—3"òÇ£»TsÉ•5M ̈¢±XÊxÖ&üºÍ†ØT•:-†YKñ[ Xú4•™•4}sTÆ2(í‡\ÇY ̆¤v/öÓÏRu•Gï8,ÄÝ5ňYH ̈_ª- _bcBE ̃;Âc`êE`ƒ] ́„~PB±a¬ûa!ÖDõ•ˆ ̇„ó¶N’b ÐG_Gçd•Qaì]d[Œ(Ø...±•‚Ëd– ;•†ÌÖ6ZœÊ•b©”K‡ÞÙ}gS¢cÍÑ_V•š0¡aö`+•‰`r’,ñìU– ui•›c6>jU[cV²$ç`†¥k6†»¥±jÂÜÇêU•ˆ ,åD§–Ÿl4‹_Hð«Ê·RJ}lÓ '6l,õÄÒÖ-ÕVZvólÖrQ%_ öAd ̈~N— ÄY— •2•Ýc,Òèé ̈[éd5¥μm•Å!Q•cÍìßVÇ"hƒFDè&ºÖ)²N‰YI— u•ù] t’WUQ ̆ ̃p—=oæ²2 ̋ q—o%ö3t ¢¦WF“Â>àׂë¥ÍW— a%VÖP"ÿ$ÒWn“!yä©&M4H ̄IyL•'7 ̊#ên ‹FcÄçzÅ^ ...¦Œ2•ðijOÅahªè-–SÄ ÌÖ5P÷ÜU÷á3Þåöƒ•0''WØ#m'T,lM÷|...2.×q«šãë‚^Ï>ãr&Rp^æwú...$‚2•ò‚•*ä*¦*Höãx•}·÷,*• •8K$å&çWyu¦ÎÒW=þšnI†Igj“e-g ̧!‚³•+ƒÔöÊ+† ́•$PìRw+„Æ•úíÂkë...„ Íj”- ~Mªšeù‰...ƒw...2í’E#Ør2e5I ́™/^·¤°)®þ&‹XowW`` ́QÄWØß•”°m8ØñJyÄòfÓŒ„”Ãì ́òUJ=”š•y ̇4¤ !ìÀ|y•...d»¤árrÑ£•cÙ’‘0s‰Âð RHù•Nï‘m0Æ:ËOl5Å ̇nTuJªæ]ˆkp¬{‹{F( W9 ̋“¹•s& *ëæŠ ̆•\Åd'•H¹È”Ín6¶;O©#é¥Xæð ̈UÑÙYy© 9„m,õ•™•›4«Xù\çg|rFÜO£]•¹7qYbœ%•“¹k ̃¹1]Ù=’• pÃØè™–Ç¥‹ Ã-œ5ýq •7ÖÑ-ÙïtPÎCô c2*...÷³ åò_ÖÇ,`s...–³Ÿƒoœv¹¢õ©u”©¢z6‘J㣠̆¦(ZB ̈ ̄²Cú!|3•–W³• ̆ó¡60: {ºH6ú,Zj}’éSŸx2Àkh[ú$§6³"«ˆWÚ\μª}az, ́†²Y‡ˆ°•«c4 ̊²Ö¿ ‘äé ̈•¡G< ̈•ó«...•;V³ªbÙ}„é©ì Ãs d-—0°•?k2s«×&K:Âñ•T³T ̧wˆÞ·tÜ]h ̋®ÌJ,f¾±ëˆ›"Ï[ÊùZ› ̄l ̇^Û ̇3Oì+“•®$;±ÕÌ=Œ °Yå§LÞ&sî6îXzS³•aÇ=9...ìjѲ%ã¢Gçμ-•Áâ¹μCæëåã ̈› ̃ ́I<ÔT-¾\ºþ° Ó²[•®Qv{Dzõ±••<[-@/-\¶Ä ̧¤L,ےXãçS;të¦Ä_›iºJ¡¶ ¹ûg, -μ5~YT|@/èíÈ3dMkG¾ÇW·ÅŸ¾eÊ–C4‡•jkêѽ{Œ¹ ̃ë ̄T ̄Ài, Òÿ•“sh û•"Æ©¦‘’B|I ̇Ãà ̋ 8\($ˆN|ñÐa ̈NÉ••zlD|PñÅ {7EíĬ ̆6ü+‡Œ£ ̇<;=z=BÜ4™°v¤³+£Ç°Ïì-Ç\4»%Á|d¬"ÐoÑ•º lƒü9`I»ºö ̈UgÑÅ{ ̄zçé-û ̆E<·••äÈœ±º‚Û {•,ìM]väŠè_°Ü—Ƭ{nËQÈ{•À•y¿d^½ôÕ°K•Ç”,šsšO†•§l¢½†dÖì<징§¹ fš¦mÇ$9¥!œ½# ˆ^ÆIÑãœs²•Rf ̃ ̧6ð^f›+£RèºK°Ú<O¦ ́9} ̆Ô\À` ̆óÓcU|ÙeÓ ̃•ÖÝ)B}'r³°Í¹Ò4’ û ́•6pÝ••etU ̇ Ó«`ËdÒZÃg•lòÌ9ˆ&I©qaÈÙ‹,È] μ¼iÚiZ>”öTμ-A ̄ú– •L6B¥Ý9<2B¥×Ås?]ã••]eïkÝ@u©•Ì)ˆ&Ÿ£ÈoÖ™ƒÅ ̈q$Ã[g(¤]%ß÷rT ̈ñA ̧F¾kúS^ ̃Þˆ"V]ö ̇Ê'ãCl w-_œè ,§£Ëûr®<§ßxåÜçs®Þ••ÔW©¥JT ̈ñG†Šý ̈ð&Šþ‡s1^z`²k™>\ ̇Õ/è6^Y¦— çF¥I~rA›]cm-£6îLw7çñ/þ=eò¹“]÷1õ ̊Ý ̃RK •ÊØ ̃¡ò×\y š-Ê‚³èT+þ9Tªp‡s©*íB±îîIçIð ̆|Ô=Ùîÿ 2þ÷ï ̆/â·R ̈Ðáݾçpÿ•[~Ë핹ñnHLã³çfF>ëóÚ±í¾ÿˆþÉÎk3 ̆¤×ÊÒ@¼Šz ¿Z[ BŠñ÷ð$•u¿kð ́xw60¡tÙ÷Ÿ]í>íÜ*•ó2¹å"‘õ-x¡ v ́êyöæýè 4gs ̄*•®Þ ê_gîß– ̈8½æ ‘ûÿSùÿ•õ§âG ±ö*•úŸr½‹ˆgGÛCØÍ 5“^ãîíÞ=]î^Kÿeè ̆Â`6• ̊ ‚`hÌr1• ÆB ́Üd.@à°qÈÀ\4ÃÆpH0Ìp9• a±ÈÒ= ̈• "Pá ̧Ì\6”È ̇¢áÌ–_1™“©0ÊQ•LÒˆäî#•ˆD¢‘ñÄF•....@©•¹Ä`g2¡SÅѱ ́Š‹;¢Q«âá... ̇=™ S•h4§‹ÆkЩàÛr...Tm‘•m ̋•]‡ ¦ ̃•Õë ̆l ̃ ðñkÜ–Š.ˆLâø9 ̈ÒÑ*•ä²•[|Ò3dÏX¦:- V½=ÉÖê• ^6…

Text truncated - open the document above for the full version.

845 Larch Ave. Elmhurst, IL 60126 phone 630.993.6306 fax 630.530.6140 email: [email protected] August 20, 1998 Federal Communications Commission EQUIPMENT APPROVAL SERVICES PO Box 358315 Pittsburgh, PA 15251-5315 Re: Request for Certification Enclosed is an application, fee in the amount of $895, and exhibits for Certification of a Remote Control Transmitter, Model 1A5235. The final instruction sheet is not available at this time, so I have included a typical instruction sheet indicating the FCC statement and important information. The FCC ID of this model, upon certification, will be HBW1341. We would appreciate your prompt attention to the submittal. Sincerely, THE CHAMBERLAIN GROUP, INC. Barbara P. Kelkhoff Manager, Product Safety LIST OF EXHIBITS 3 FUNCTION, REMOTE CONTROL TRANSMITTER MODEL 1A5235 1. Expository Statement 2. Theory of Operation 3. Schematic 4. Photographs 5. FCC Label Drawing 6. Operating Instructions 7. Test Report EXPOSITORY STATEMENT 3 FUNCTION, REMOTE CONTROL TRANSMITTER MODEL 1A5235 1. Since the final instruction sheet is not available at this time, a marked-up typical version has been included. The instructions include statements required to assure compliance with the Commission's Rules; Part 15. 2. Labeling is in accordance with the Commission's labeling requirements, Parts 2 and 15, Section 15.19. 3. This transmitter is intended for use with the certified receivers of our manufacture only. 4. The transmitter is equipped with an automatically releasing push-button switch. Transmission is terminated upon release of the push-button. 5. The 1A5235 is factory set to 433 ± 0.1% MHz. It is not intended to be readjusted in the field, and specific instruction prohibiting tampering are provided to the user. 6. Test data for the Model 1A5235 is part of this submission. No emissions were detected in the forbidden bands below 1.0 GHz. Certified by: Barbara P. Kelkhoff Manager, Product Safety THEORY OF OPERATION AND CIRCUIT DESCRIPTION MODEL 1A5235 3 FUNCTION, REMOTE CONTROL TRANSMITTER (Please refer to enclosed schematic drawing: 195D1341A) The 1A5235 transmitter consists of a low power RF oscillator (Q2 and associated components), a digital encoder (U1 and related components), and on/off switches. The RF oscillator, Q2, is of the grounded base type. C2, C3, C5, C8, and the copper loop, L2, set the center frequency of the oscillator at 433 MHz. C4 and C7, with the internal capacitance of Q2, establish feedback levels and harmonic suppression. R1, R2 and R5 establish dc operating conditions on Q2 and help improve temperature stability. U1 and related components generate a digital code. This code is used in the companion receiver to identify a particular transmitter or function. The 3V battery circuit is equipped with an automatically releasing (normally off) push-button switches that supply voltage to U1 when SW1, SW2 or SW3 are depressed. U1 contains a voltage switcher circuit that increases the 3V to 9V . A square wave output is applied to driver Q1 through R4. L1, D1 and C1 boost and filter the voltage to 9V. This is applied to Q2, regulated to 9V by U1, and monitored through pin 5. SW1-SW3 and U1 provide three input functions. The digital signal is randomly programmed and the code is stored within U1. 1. EXPOSITORY STATEMENT 2. THEORY OF OPERATION 3. SCHEMATIC 4. PHOTOGRAPHS 5. FCC LABEL DRAWING 6. OPERATING INSTRUCTIONS 7. TEST REPORT