HBW1614Superregenerative Receiver Model 412-315HM

TM Universal Receiver Model 412HM OWNERS MANUAL SPECIFICATIONS Output Rating........................5 Amps 28VAC or DC Max. Power ......................12VDC or 18 to 35VAC/DC, @ 30ma RF Frequency........................................................390MHz If the power is other than shown in specifications, Accessory Transformer Model 85 is required. Model 86 Coaxial Cable Kit is also available. Accessory Transmitters – Series 50, 60, 70, 80 and 90. The 412HM universal Receiver can be used with up to 15 rolling code transmitters or passwords in high security mode. Alternately, it can be used with up to 31 of any type transmitter in normal security mode, including any combination of rolling code, billion code, or code switch remotes. The receiver and antenna use TVType F coaxial connectors. The antenna can be plugged directly onto the receiver or mounted to a bracket and connected to the receiver with Model 86 Coaxial Cable Kit, depending on your requirements. Select a location for the receiver which allows access to the terminals and space for the antenna (as far from metal structures as possible and preferably with the antenna in an upright position). Fasten the receiver securely with screws through the two holes provided in the cover flanges. FIGURE 1 – WITHOUT TRANSFORMER:Connect bell wire (not supplied) to receiver terminals 1 and 2, and to opener radio power terminals. All receiver terminals are unpolarized. Also connect bell wire to receiver terminal 4 and opener terminal 2. Make a jumper wire connection to receiver terminals 1 and 3 as shown. FIGURE 2 – WITH TRANSFORMER MODEL 85:Receiver terminals 1 and 2 are not used. Connect bell wire to receiver terminals 3 and 4 and to opener terminals used for push button controls. The transformer plugs into a 120V outlet. Children operating or playing with a garage door opener can injure themselves and others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control push button or the remote control transmitters. Install the receiver (and all door control push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible. WARNING Disconnect power to opener before installing receiver or removing/replacing receiver cover. WARNING 1 2 3 1 2 3 RECEIVER (Bottom) FIGURE 1 OPENER 24 v TRANS PRIMARY 4 Common Relay RECEIVER (Top) Connect Antenna WALL BUTTON 1 2 3 1 3 RECEIVER (Bottom) WALL BUTTON OPENER 24 v TRANS PRIMARY 4 Common RECEIVER (Top) Connect Antenna Connect Transformer FIGURE 2 2 Relay To comply with FCC/IC rules, adjustment or modification of receiver and/or transmitter is prohibited, except for changing the code setting and replacing the transmitter battery. THERE ARE NO USER SERVICEABLE PARTS. Use a screwdriver to pry open the receiver cover as shown. Re-connect power to opener. 1. Press and HOLD the new remote control push button. 2. Then press the "Smart" button on the receiver. The adjacent indicator light will flash. Release the remote push button. The opener will now operate when the remote control push button is pressed. Return front panel to receiver. NOTE:If the remote control push button is not held down until the receiver indicator light flashes, the receiver will not learn the code. To Erase all Remote Control Codes: • Press and hold the "Smart" button on the receiver panel until the indicator light turns off (about 6 seconds). All the codes the receiver has learned will be erased. • Repeat Steps 1 and 2 to reprogram the receiver for each remote control transmitter in use. Side 2 contains instructions for changing output duration, voltage settings, and security mode. OPENING RECEIVER OPEN RECEIVER Smart Button Indicator Light Power Supply Jumper Security Mode Jumper Output Duration Jumper SET RECEIVER TO MATCH REMOTE CONTROL(S) CODE The receiver can be set for either constant or momentary closure on the output contacts. With the jumper in the “MOM” (Momentary) position, the contacts will close for 1/4 second regardless of the length of radio transmission. With the jumper in “CONST” (Constant) position, the contacts will stay closed as long as the radio continues transmitting. The receiver is factory set at M. TO SET OUTPUT DURATION The use of radios incorporating constant closure contacts on residential operators with fail-safe infra-red protectors is prohibited. WARNING The receiver can be powered with either 24V AC/DC or with 12V DC. The jumper must be in the 24V position for use with 24V, and in 12V position for use with 12 VDC. The jumper must be set to the proper voltage to avoid damage to the receiver. The receiver is factory set at 24V. The jumper must be set at the HIGH position for the receiver to operate in high security mode. It must be set at NORMAL position to operate at the normal mode. When changing from normal to high security mode, any previous transmitter codes must be erased. Repeat Steps 1 and 2 on Side 1 to reprogram the receiver for each remote control transmitter in use. The receiver is factory set at HIGH. TO SET POWER SUPPLY VOLTAGE TO SET SECURITY MODE The use of 24V with the jumper in 12V position will cause permanent damage to the receiver. CAUTION © 1996, The Chamberlain Group, Inc. 114A2143All Rights ReservedPrinted in Mexico MOM. CONST. Output Duration Terminals Jumper MOMENTARY OPERATION MOM. CONST. Output Duration Terminals Jumper CONSTANT OPERATION 12V POSITION Circuit Board 24V 12V M C Jumper Power Supply Terminals N OR HIGH Circuit Board 24V 12V M C Jumper 24V POSITION Power Supply Terminals NO HIGH 24V 12V M C Jumper HIGH SECURITY MODE Security Mode Terminals NORM HIGH 24V 12V M C Jumper NORMAL SECURITY MODE Security Mode Terminals NORM HIGH

October 29, 2001 Chamberlain Group Inc. Attn:Mr. Hank Sieradzki 845 Larch Ave Elmhurst, IL 60126 UL Reference:File MC3181, Project 01NK44622 Subject:EMC Test and Measurement Report for Model G412-315LM Super-regenerative Receiver Dear Mr. Sieradzki: We have provided with this letter your EMC Test Report for the above referenced model. The product was determined to comply with the requirements noted in the report. Please review the attached report and direct any questions or comments to me. Samples were returned to your attention. We appreciate your interest in UL’s EMC Services, and encourage you to contact us in the future should you need EMC test services. This closes Project 01NK44622. Best regards,Reviewed by: Bart Mucha (Ext 41216)Jack Steiner Associate Project EngineerEngineering Group Leader International EMC ServicesInternational EMC Services UL International EMC Services 333 Pfingsten Road Northbrook, Illinois 60062-2096 (800) 873-8536 Fax No. (847) 272-8864 http://www.ul.com/emc/ File: MC3181 Project: 01NK44622 Page 1 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC EMC – TEST REPORT Issue Date: October 24, 2001 √EMISSIONS IMMUNITY Test Report File No.:MC3181 Project No.:01NK44622 Model / Type:G412-315LM Kind of Product:Super-regenerative Receiver Applicant:Chamberlain Group Inc. License Holder:Chamberlain Group Inc. Address:845 Larch Ave :Elmhurst, IL 60126 : Manufacturer:Same as Applicant : : : Test Result:COMPLIANT This report without appendices consists of 9 pages. Appendix A contains test photos, and Appendix B contains original test data. The data contained in this report reflects only the items tested in the configurations and mode of operations described. An attempt has been made to arrange the EUT, with the equipment provided, into a test configuration which maximizes the observed emissions of the EUT while simulating, as close as practical, a typical end-use installation. Underwriters Laboratories Inc. authorizes the above company to reproduce this report provided it is reproduced in its entirety. Underwriters Laboratories Inc.333 Pfingsten Rd. Northbrook, IL 60062 Fax: (847) 272-8864 File: MC3181 Project: 01NK44622 Page 2 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC REPORT DIRECTORY SECTIONTITLE GENERAL 1.0 General Product Description 1.1 Model Differences 1.2 Environmental Conditions in Test Lab 1.3 Calibration Details of Equipment Used for Measurement 1.4 EUT (Equipment Under Test) Configuration 1.5EUT Operating Mode 1.6Device Modifications EMISSIONS 2.0Emissions Test Regulations Conducted Voltage Radiated Electric Field Emissions IMMUNITY 3.0Immunity Test Regulations CONCLUSION 4.0General Remarks 4.1Summary APPENDICIES ATest Setups (Photos, Diagrams and Drawings) BTest Data File: MC3181 Project: 01NK44622 Page 3 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.0GENERAL PRODUCT DESCRIPTION The EUT (Equipment Under Test) was a super-regenerative receiver model: G412- 315LM for use with garage door openers. 1.0.1Equipment Mobility: Wall, Ceiling-mount 1.0.2Test Voltage and Frequency: Voltage (V)Frequency (Hz) 12060 1.1MODEL DIFFERENCES Any other model(s) represented by the models tested in this investigation will be documented by the manufacturer. 1.2ENVIRONMENTAL CONDITIONS IN TEST LAB Temperature:20-25 °C Relative Humidity:30-60% RH Atmospheric Pressure:860-1060 mbar 1.3CALIBRATION OF EQUIPMENT USED FOR MEASUREMENT All test equipment and test accessories are calibrated on a regular basis. The maximum time between calibrations is one year or what is recommended by the manufacturer, whichever is less. All test equipment calibrations are traceable to the National Institute of Standards and Technology (NIST), therefore, all test data recorded in this report is traceable to NIST. File: MC3181 Project: 01NK44622 Page 4 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.4EUT CONFIGURATION(s) See Appendix A for individual set-up configuration(s). In addition to the EUT, the following peripheral devices and/or cables were connected during the measurement: DeviceManufacturerModelSerial #FCC ID Super – regenerative Receiver ChamberlainG412-315LM (PCB assembly 1A5573) -- 24VAC AdapterLZR ElectronicsAA-2420-- GDO simulatorChamberlain1160LM2912C00774- CableManufacturerLengthTypeShield Type Shield Termination I/O-5MCL2XNonenone 1.5 EUT OPERATING MODE(s) The equipment under test was operated during the measurements under the following conditions: The Receiver was tested in two modes: IDLE – for Radiated Emissions and Conducted Emissions COHERED – for Radiated Emissions Only (there was no difference in conducted emissions when compared to IDLE mode) 1.6DEVICE MODIFICATIONS The following modifications were necessary for compliance: None. File: MC3181 Project: 01NK44622 Page 5 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 2.0EMISSIONS TEST REGULATIONS The EUT was considered to be a Class B device. Emissions testing was performed according to the following regulations: 47 CFR Part 15 Subpart B: 2000 + ANSI C63.4 - 1992 File: MC3181 Project: 01NK44622 Page 6 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC CONDUCTED VOLTAGE EMISSIONS Test Location Ground Plane (Test Station 3) UL Procedure 3014ANBK-LPG-001 Test Instruments Spectrum Analyzer / Quasi-peak Adapter Advantest Model 3261A Spectrum Analyzer No. EMC4084 Model R3551 Preselector No. EMC4088 Line Impedance Stabilization Networks (LISNs) SOLAR Model 8602-50-TS-50-N S/N 963903 No. EMC4064 SOLAR Model 8602-50-TS-50-N S/N 963904 No. EMC4065 Transient Limiter Electro – Metrics Model: EM-7600-2No. EMC4224 Frequency Range on each line 450 kHz to 30MHz Test Results The requirements are: MET Remarks See App. B for complete test results. File: MC3181 Project: 01NK44622 Page 7 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC RADIATED ELECTRIC FIELD EMISSIONS Test Location 10 Meter Semi-Anechoic Chamber UL Pr…

Text truncated - open the document above for the full version.

THEORY OF OPERATION AND CIRCUIT DESCRIPTION MODEL 412-315HM REMOTE CONTROL RADIO RECEIVER Please refer to enclosed schematic 195D1614 The radio uses the analog input into an external comparator, which converts the signal to digital for input to digital radio in. The radio signal comes in at any signal level from 10mV to approximately 3V of swing with a D.C. point of 2.5V. This input is avg. detected by R20 and C17 which is fed into one side of the comparator while the undetected signal is fed into the other. Diode D1 is used for overload protection of the comparator. R21 is used to compensate for the change in duty cycle of the radio signal due to different pulse widths. MOSFET Q3 provides extra noise immunity during the radio blank periods. Normally, the active clamp on the micro-controller turns on Q3, causing the MOSFET to appear as a small resistor to the rest of the circuit. When a valid radio code word is detected, the active clamp is set low, turning the MOSFET off. This causes the MOSFET to appear as an open circuit, and holds the voltage across C17 at a constant level. This ensures that the reference voltage does not drift toward the noise floor during a radio reception. The MOSFET is again turned on at the end of the radio word, when a radio error occurs, or when 500ms have passed without any radio signal. The learn switch is used to place the unit into learn mode by monitoring pin 6. When the switch is pressed, learn mode is set and the LED on pin 18 is turned on. If the switch is held active for more then 6 seconds the memory will be erased and the learn mode will be cleared. If while the unit is in learn mode a radio code is properly received twice then that code is placed in memory (if not already there), and the learn mode is cleared. If within 30 seconds the learn mode is not cleared the learn mode will time out and be cleared. The switch on pin 6 is the command input and acts like a radio code being received as long as the switch is held. This switch is debounced with a debounce time of 80mS±10mS. The switches are read by the micro-controller (U2) setting the input pins 6 and 8 into the input mode. R29 and R30 are needed to limit the current when S1 or S2 is active. R38 is for limiting the LED current. R31 and R32 are for limiting the ESD current. The active clamp signal is generated on pin 9. Upon receiving a valid Chamberlain code, the circuit “clamps” down on the signal, doing an average detection of the incoming signal. This improves the range of the radio reception, and allows better “filtering” of noise spikes to improve radio performance. The oscillator pins 15 and 16 are used for the main clock generation. These pins will have a ceramic resonator connected between them to generate the 4.0 MHz main clock frequency.

October 29, 2001 Chamberlain Group Inc. Attn:Mr. Hank Sieradzki 845 Larch Ave Elmhurst, IL 60126 UL Reference:File MC3181, Project 01NK44622 Subject:EMC Test and Measurement Report for Model G412-315LM Super-regenerative Receiver Dear Mr. Sieradzki: We have provided with this letter your EMC Test Report for the above referenced model. The product was determined to comply with the requirements noted in the report. Please review the attached report and direct any questions or comments to me. Samples were returned to your attention. We appreciate your interest in UL’s EMC Services, and encourage you to contact us in the future should you need EMC test services. This closes Project 01NK44622. Best regards,Reviewed by: Bart Mucha (Ext 41216)Jack Steiner Associate Project EngineerEngineering Group Leader International EMC ServicesInternational EMC Services UL International EMC Services 333 Pfingsten Road Northbrook, Illinois 60062-2096 (800) 873-8536 Fax No. (847) 272-8864 http://www.ul.com/emc/ File: MC3181 Project: 01NK44622 Page 1 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC EMC – TEST REPORT Issue Date: October 24, 2001 √EMISSIONS IMMUNITY Test Report File No.:MC3181 Project No.:01NK44622 Model / Type:G412-315LM Kind of Product:Super-regenerative Receiver Applicant:Chamberlain Group Inc. License Holder:Chamberlain Group Inc. Address:845 Larch Ave :Elmhurst, IL 60126 : Manufacturer:Same as Applicant : : : Test Result:COMPLIANT This report without appendices consists of 9 pages. Appendix A contains test photos, and Appendix B contains original test data. The data contained in this report reflects only the items tested in the configurations and mode of operations described. An attempt has been made to arrange the EUT, with the equipment provided, into a test configuration which maximizes the observed emissions of the EUT while simulating, as close as practical, a typical end-use installation. Underwriters Laboratories Inc. authorizes the above company to reproduce this report provided it is reproduced in its entirety. Underwriters Laboratories Inc.333 Pfingsten Rd. Northbrook, IL 60062 Fax: (847) 272-8864 File: MC3181 Project: 01NK44622 Page 2 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC REPORT DIRECTORY SECTIONTITLE GENERAL 1.0 General Product Description 1.1 Model Differences 1.2 Environmental Conditions in Test Lab 1.3 Calibration Details of Equipment Used for Measurement 1.4 EUT (Equipment Under Test) Configuration 1.5EUT Operating Mode 1.6Device Modifications EMISSIONS 2.0Emissions Test Regulations Conducted Voltage Radiated Electric Field Emissions IMMUNITY 3.0Immunity Test Regulations CONCLUSION 4.0General Remarks 4.1Summary APPENDICIES ATest Setups (Photos, Diagrams and Drawings) BTest Data File: MC3181 Project: 01NK44622 Page 3 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.0GENERAL PRODUCT DESCRIPTION The EUT (Equipment Under Test) was a super-regenerative receiver model: G412- 315LM for use with garage door openers. 1.0.1Equipment Mobility: Wall, Ceiling-mount 1.0.2Test Voltage and Frequency: Voltage (V)Frequency (Hz) 12060 1.1MODEL DIFFERENCES Any other model(s) represented by the models tested in this investigation will be documented by the manufacturer. 1.2ENVIRONMENTAL CONDITIONS IN TEST LAB Temperature:20-25 °C Relative Humidity:30-60% RH Atmospheric Pressure:860-1060 mbar 1.3CALIBRATION OF EQUIPMENT USED FOR MEASUREMENT All test equipment and test accessories are calibrated on a regular basis. The maximum time between calibrations is one year or what is recommended by the manufacturer, whichever is less. All test equipment calibrations are traceable to the National Institute of Standards and Technology (NIST), therefore, all test data recorded in this report is traceable to NIST. File: MC3181 Project: 01NK44622 Page 4 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.4EUT CONFIGURATION(s) See Appendix A for individual set-up configuration(s). In addition to the EUT, the following peripheral devices and/or cables were connected during the measurement: DeviceManufacturerModelSerial #FCC ID Super – regenerative Receiver ChamberlainG412-315LM (PCB assembly 1A5573) -- 24VAC AdapterLZR ElectronicsAA-2420-- GDO simulatorChamberlain1160LM2912C00774- CableManufacturerLengthTypeShield Type Shield Termination I/O-5MCL2XNonenone 1.5 EUT OPERATING MODE(s) The equipment under test was operated during the measurements under the following conditions: The Receiver was tested in two modes: IDLE – for Radiated Emissions and Conducted Emissions COHERED – for Radiated Emissions Only (there was no difference in conducted emissions when compared to IDLE mode) 1.6DEVICE MODIFICATIONS The following modifications were necessary for compliance: None. File: MC3181 Project: 01NK44622 Page 5 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 2.0EMISSIONS TEST REGULATIONS The EUT was considered to be a Class B device. Emissions testing was performed according to the following regulations: 47 CFR Part 15 Subpart B: 2000 + ANSI C63.4 - 1992 File: MC3181 Project: 01NK44622 Page 6 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC CONDUCTED VOLTAGE EMISSIONS Test Location Ground Plane (Test Station 3) UL Procedure 3014ANBK-LPG-001 Test Instruments Spectrum Analyzer / Quasi-peak Adapter Advantest Model 3261A Spectrum Analyzer No. EMC4084 Model R3551 Preselector No. EMC4088 Line Impedance Stabilization Networks (LISNs) SOLAR Model 8602-50-TS-50-N S/N 963903 No. EMC4064 SOLAR Model 8602-50-TS-50-N S/N 963904 No. EMC4065 Transient Limiter Electro – Metrics Model: EM-7600-2No. EMC4224 Frequency Range on each line 450 kHz to 30MHz Test Results The requirements are: MET Remarks See App. B for complete test results. File: MC3181 Project: 01NK44622 Page 7 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC RADIATED ELECTRIC FIELD EMISSIONS Test Location 10 Meter Semi-Anechoic Chamber UL Pr…

Text truncated - open the document above for the full version.

October 29, 2001 Chamberlain Group Inc. Attn:Mr. Hank Sieradzki 845 Larch Ave Elmhurst, IL 60126 UL Reference:File MC3181, Project 01NK44622 Subject:EMC Test and Measurement Report for Model G412-315LM Super-regenerative Receiver Dear Mr. Sieradzki: We have provided with this letter your EMC Test Report for the above referenced model. The product was determined to comply with the requirements noted in the report. Please review the attached report and direct any questions or comments to me. Samples were returned to your attention. We appreciate your interest in UL’s EMC Services, and encourage you to contact us in the future should you need EMC test services. This closes Project 01NK44622. Best regards,Reviewed by: Bart Mucha (Ext 41216)Jack Steiner Associate Project EngineerEngineering Group Leader International EMC ServicesInternational EMC Services UL International EMC Services 333 Pfingsten Road Northbrook, Illinois 60062-2096 (800) 873-8536 Fax No. (847) 272-8864 http://www.ul.com/emc/ File: MC3181 Project: 01NK44622 Page 1 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC EMC – TEST REPORT Issue Date: October 24, 2001 √EMISSIONS IMMUNITY Test Report File No.:MC3181 Project No.:01NK44622 Model / Type:G412-315LM Kind of Product:Super-regenerative Receiver Applicant:Chamberlain Group Inc. License Holder:Chamberlain Group Inc. Address:845 Larch Ave :Elmhurst, IL 60126 : Manufacturer:Same as Applicant : : : Test Result:COMPLIANT This report without appendices consists of 9 pages. Appendix A contains test photos, and Appendix B contains original test data. The data contained in this report reflects only the items tested in the configurations and mode of operations described. An attempt has been made to arrange the EUT, with the equipment provided, into a test configuration which maximizes the observed emissions of the EUT while simulating, as close as practical, a typical end-use installation. Underwriters Laboratories Inc. authorizes the above company to reproduce this report provided it is reproduced in its entirety. Underwriters Laboratories Inc.333 Pfingsten Rd. Northbrook, IL 60062 Fax: (847) 272-8864 File: MC3181 Project: 01NK44622 Page 2 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC REPORT DIRECTORY SECTIONTITLE GENERAL 1.0 General Product Description 1.1 Model Differences 1.2 Environmental Conditions in Test Lab 1.3 Calibration Details of Equipment Used for Measurement 1.4 EUT (Equipment Under Test) Configuration 1.5EUT Operating Mode 1.6Device Modifications EMISSIONS 2.0Emissions Test Regulations Conducted Voltage Radiated Electric Field Emissions IMMUNITY 3.0Immunity Test Regulations CONCLUSION 4.0General Remarks 4.1Summary APPENDICIES ATest Setups (Photos, Diagrams and Drawings) BTest Data File: MC3181 Project: 01NK44622 Page 3 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.0GENERAL PRODUCT DESCRIPTION The EUT (Equipment Under Test) was a super-regenerative receiver model: G412- 315LM for use with garage door openers. 1.0.1Equipment Mobility: Wall, Ceiling-mount 1.0.2Test Voltage and Frequency: Voltage (V)Frequency (Hz) 12060 1.1MODEL DIFFERENCES Any other model(s) represented by the models tested in this investigation will be documented by the manufacturer. 1.2ENVIRONMENTAL CONDITIONS IN TEST LAB Temperature:20-25 °C Relative Humidity:30-60% RH Atmospheric Pressure:860-1060 mbar 1.3CALIBRATION OF EQUIPMENT USED FOR MEASUREMENT All test equipment and test accessories are calibrated on a regular basis. The maximum time between calibrations is one year or what is recommended by the manufacturer, whichever is less. All test equipment calibrations are traceable to the National Institute of Standards and Technology (NIST), therefore, all test data recorded in this report is traceable to NIST. File: MC3181 Project: 01NK44622 Page 4 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.4EUT CONFIGURATION(s) See Appendix A for individual set-up configuration(s). In addition to the EUT, the following peripheral devices and/or cables were connected during the measurement: DeviceManufacturerModelSerial #FCC ID Super – regenerative Receiver ChamberlainG412-315LM (PCB assembly 1A5573) -- 24VAC AdapterLZR ElectronicsAA-2420-- GDO simulatorChamberlain1160LM2912C00774- CableManufacturerLengthTypeShield Type Shield Termination I/O-5MCL2XNonenone 1.5 EUT OPERATING MODE(s) The equipment under test was operated during the measurements under the following conditions: The Receiver was tested in two modes: IDLE – for Radiated Emissions and Conducted Emissions COHERED – for Radiated Emissions Only (there was no difference in conducted emissions when compared to IDLE mode) 1.6DEVICE MODIFICATIONS The following modifications were necessary for compliance: None. File: MC3181 Project: 01NK44622 Page 5 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC 2.0EMISSIONS TEST REGULATIONS The EUT was considered to be a Class B device. Emissions testing was performed according to the following regulations: 47 CFR Part 15 Subpart B: 2000 + ANSI C63.4 - 1992 File: MC3181 Project: 01NK44622 Page 6 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC CONDUCTED VOLTAGE EMISSIONS Test Location Ground Plane (Test Station 3) UL Procedure 3014ANBK-LPG-001 Test Instruments Spectrum Analyzer / Quasi-peak Adapter Advantest Model 3261A Spectrum Analyzer No. EMC4084 Model R3551 Preselector No. EMC4088 Line Impedance Stabilization Networks (LISNs) SOLAR Model 8602-50-TS-50-N S/N 963903 No. EMC4064 SOLAR Model 8602-50-TS-50-N S/N 963904 No. EMC4065 Transient Limiter Electro – Metrics Model: EM-7600-2No. EMC4224 Frequency Range on each line 450 kHz to 30MHz Test Results The requirements are: MET Remarks See App. B for complete test results. File: MC3181 Project: 01NK44622 Page 7 of 9 UL International EMC Services www.ul.com/emc (800) USE UL EMC RADIATED ELECTRIC FIELD EMISSIONS Test Location 10 Meter Semi-Anechoic Chamber UL Pr…

Text truncated - open the document above for the full version.

Concucted Voltage Test Setup Photos of - 535-315LM Radiated Emissions Test Setup Photos for 535-315LM