HBW2555NHomelink Rptr MC

RATING: 120 Vac, 60Hz, 35mA INSTALL AND PROGRAM THE HOMELINK COMPATIBILITY BRIDGE To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. HOMELINK ® COMPATIBILITY BRIDGE™ INTRODUCTION The HomeLink Compatibility Bridge™ is designed to allow compatibility between a new Chamberlain, Sears Craftsman, or LiftMaster* garage door opener and the HomeLink ® system in your vehicle. Refer to the your vehicle owner’s manual for specific instructions on programming the HomeLink system. Your model may look different than illustrated in this programming guide. * Chamberlain and LiftMaster are Trademarks of Chamberlain Group. Sears is a Trademark of Sears Roebuck. NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The device shall be used in such a manner that the potential for human contact normal operation is minimized. This equipment complies with RSS-102 radiation exposure limits. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. ATTENTIONATTENTION WARNINGWARNING WARNINGWARNING WARNINGWARNING AntennaIndicator Light HomeLink Compatibility Bridge Be sure that your vehicle is parked outside of the garage before programming the HomeLink Compatibility Bridge. Two people may be needed to program the HomeLink system. 1. Program the new remote control included with the HomeLink Compatibility Bridge to the Homelink button in your vehicle. Refer to the owner’s manual for your vehicle for programming steps. 2. Plug the HomeLink Compatibility Bridge into a 120 Vac polarized outlet, located as close as possible to your garage door opener. 3. Straighten the antenna. 4. Press and release the YELLOW Learn button on the garage door opener. The Learn LED will glow steadily. 5. Within 30 seconds press and hold the programmed HomeLink button in your vehicle. 6. Release the HomeLink button when the garage door opener light blinks. If light bulbs are not installed in the garage door opener, two clicks will be heard. Programming is complete. 7. To ensure the garage door opener operates from the HomeLink button, press the programmed HomeLink button in the vehicle. If it does not operate the garage door opener, repeat the steps. Remote Control NOTES: • If you are using the HomeLink Compatibility Bridge with a garage door opener that has a Battery Backup system, ensure the original remote control is programmed to the garage door opener and place it in your glove box for use in the event of a power outage. • The remote control included with the Compatibility Bridge MUST be kept for future programming (i.e. a new vehicle, a new garage door opener, etc.). INDICE : 120 Vac, 60Hz, 35mA INSTALLER ET PROGRAMMER LE HOMELINK COMPATIBILITY BRIDGE Pour prévenir d’éventuelles BLESSURES GRAVES ou LA MORT à cause de la chute d’une porte en mouvement ou d’une porte de garage : • Ne laissez JAMAIS la télécommande à portée des enfants. Ne laissez aucun enfant faire fonctionner une télécommande ou jouer avec elle. • Actionner la porte ou le portail UNIQUEMENT lorsqu’ils sont bien visibles et bien ajustés et que rien ne fait obstacle à leur mouvement. • TOUJOURS surveiller du regard le portail ou la porte de garage jusqu’à sa fermeture complète. Ne JAMAIS laisser personne franchir une porte ou un portail en mouvement. HOMELINK ® COMPATIBILITY BRIDGE™ INTRODUCTION L’ensemble de HomeLink Compatibility Bridge™ a été conçu de façon à permettre la compatibilité entre un ouvre-porte de garage neuf de marque Chamberlain, Sears Craftsman ou LiftMaster* et le système HomeLink ® de votre véhicule. Reportez-vous au guide de l’utilisateur de votre véhicule pour obtenir des instructions spécifiques sur la programmation du système HomeLink. Votre modèle peut sembler différent de celui qui est illustré dans ce guide de programmation. * Chamberlain et LiftMaster sont des marques déposées de Chamberlain Group. Sears est une marque déposée de Sears Roebuck. AVIS : Afin de se conformer aux réglementations du FCC ou d’Industrie Canada (IC), tout réglage ou modification de ce récepteur ou cet émetteur est interdit, sauf pour modifier le réglage du code ou remplacer la pile. IL N’EXISTE AUCUNE AUTRE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement ATTENTIONATTENTION AVERTISSEMENTAVERTISSEMENT AVERTISSEMENTAVERTISSEMENT AVERTISSEMENTAVERTISSEMENT Antenne Télécommande Témoin lumineux HomeLink Compatibility Bridge Veillez à ce que votre véhicule soit garé à l’extérieur du garage avant de programmer l’ensemble de HomeLink Compatibility Bridge. Il faudrait peut-être deux personnes pour programmer le système HomeLink. 1. Programmez la n…

Text truncated - open the document above for the full version.

RATING: 120 Vac, 60Hz, 35mA INSTALL AND PROGRAM THE HOMELINK COMPATIBILITY BRIDGE To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. HOMELINK ® COMPATIBILITY BRIDGE™ INTRODUCTION The HomeLink Compatibility Bridge™ is designed to allow compatibility between a new Chamberlain, Sears Craftsman, or LiftMaster* garage door opener and the HomeLink ® system in your vehicle. Refer to the your vehicle owner’s manual for specific instructions on programming the HomeLink system. Your model may look different than illustrated in this programming guide. * Chamberlain and LiftMaster are Trademarks of Chamberlain Group. Sears is a Trademark of Sears Roebuck. NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. AntennaIndicator Light HomeLink Compatibility Bridge Be sure that your vehicle is parked outside of the garage before programming the HomeLink Compatibility Bridge. Two people may be needed to program the HomeLink system. 1. Program the new remote control included with the HomeLink Compatibility Bridge to the Homelink button in your vehicle. Refer to the owner’s manual for your vehicle for programming steps. 2. Plug the HomeLink Compatibility Bridge into a 120 Vac polarized outlet, located as close as possible to your garage door opener. 3. Straighten the antenna. 4. Press and release the YELLOW Learn button on the garage door opener. The Learn LED will glow steadily. 5. Within 30 seconds press and hold the programmed HomeLink button in your vehicle. 6. Release the HomeLink button when the garage door opener light blinks. If light bulbs are not installed in the garage door opener, two clicks will be heard. Programming is complete. 7. To ensure the garage door opener operates from the HomeLink button, press the programmed HomeLink button in the vehicle. If it does not operate the garage door opener, repeat the steps. Remote Control NOTES: • If you are using the HomeLink Compatibility Bridge with a garage door opener that has a Battery Backup system, ensure the original remote control is programmed to the garage door opener and place it in your glove box for use in the event of a power outage. • The remote control included with the Compatibility Bridge MUST be kept for future programming (i.e. a new vehicle, a new garage door opener, etc.). INDICE : 120 Vac, 60Hz, 35mA INSTALLER ET PROGRAMMER LE HOMELINK COMPATIBILITY BRIDGE Pour prévenir d’éventuelles BLESSURES GRAVES ou LA MORT à cause de la chute d’une porte en mouvement ou d’une porte de garage : • Ne laissez JAMAIS la télécommande à portée des enfants. Ne laissez aucun enfant faire fonctionner une télécommande ou jouer avec elle. • Actionner la porte ou le portail UNIQUEMENT lorsqu’ils sont bien visibles et bien ajustés et que rien ne fait obstacle à leur mouvement. • TOUJOURS surveiller du regard le portail ou la porte de garage jusqu’à sa fermeture complète. Ne JAMAIS laisser personne franchir une porte ou un portail en mouvement. HOMELINK ® COMPATIBILITY BRIDGE™ INTRODUCTION L’ensemble de HomeLink Compatibility Bridge™ a été conçu de façon à permettre la compatibilité entre un ouvre-porte de garage neuf de marque Chamberlain, Sears Craftsman ou LiftMaster* et le système HomeLink ® de votre véhicule. Reportez-vous au guide de l’utilisateur de votre véhicule pour obtenir des instructions spécifiques sur la programmation du système HomeLink. Votre modèle peut sembler différent de celui qui est illustré dans ce guide de programmation. * Chamberlain et LiftMaster sont des marques déposées de Chamberlain Group. Sears est une marque déposée de Sears Roebuck. AVIS : Afin de se conformer aux réglementations du FCC ou d’Industrie Canada (IC), tout réglage ou modification de ce récepteur ou cet émetteur est interdit, sauf pour modifier le réglage du code ou remplacer la pile. IL N’EXISTE AUCUNE AUTRE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. Conformité vérifiée pour répondre aux normes de la FCC DANS LE CADRE D’UNE UTILISATION DOMESTIQUE OU AU BUREAU. L’utilisation est sujette aux deux conditions suivantes : (1) ce dispositif ne peut causer des interférences nuisibles ; (2) ce dispositif doit accepter toute interférence reçue, y compris une interférence pouvant causer un fonctionnement non désiré. ATTENTION AVERTISSEMENT AVERTISSEMENT AVERTISSEMENT Antenne Télécommande Témoin lumineux HomeLink Compatibility Bridge Veillez à ce que votre véhicule soit garé à l’extérieur du garage avant de programmer l’ensemble de HomeLink Compatibility Bridge. Il faudrait peut-être deux personnes pour programmer le système HomeLink. 1. Programmez la nouvelle télécommande incluse avec la trousse du HomeLink Compatibility Bridge au bouton HomeLink dans votre véhicule. Reportez-vous au guide de l’utilisateur de votre véhicule pour connaître les étapes de la programmation. 2. Branchez le HomeLink Compatibility Bridge dans une prise polarisée de 120 Vac, situé aussi près que possible de votre louvre-porte de garage. 3. Redressez l’antenne. 4. Appuyez sur le bouton de programmation JAUNE de l’ouvre-porte de garage, puis relâchez-le. Le témoin DEL de programmation s’allumera de façon conti…

Text truncated - open the document above for the full version.

Thank you. Regards, Signature: Thomas DeSilvia Date: May 30, 2023 Signed by: Thomas DeSilvia applicant is not identified on the covered list as an entity producing covered equipment. The ChamberlainGroupLLC(“theapplicant”) certifies that as of the date of the filing of the application, the authorization pursuant to section 2.903 of the FCC rules. sought is not “covered” equipment prohibited from receiving an equipment The Chamberlain Group LLC (“the applicant”) certifies that the equipment for which authorization is Covered List. equipment and video surveillance equipment produced by entities identified on the Commission’s the Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment that poses an unacceptable risk to national security or the safety of U.S. persons. Specifically, Commission adopted new FCC requirements to protect the nation’s networks and supply chains from Pursuant to FCC 22-84 Report and Order and KDB 986446 D01 Covered Equipment v01, the Date: May 30, 2023 Columbia, MD 21046 7435 Oakland Mills Rd Application Processing Branch Equipment Authorization Division TO: Federal Communication Commission Certifications FCC ID: HBW2555N concerning “covered” equipment. Section 2.911(d)(5)(i)-(ii).

Regards, Signature: Thomas DeSilvia Date: May 30, 2023 Signed by: Thomas DeSilvia This Agreement is valid until rescinded by the Applicant FRN: 004301545 Email: [email protected] Telephone No: 1-630-993-8618 Oak Brook, IL. 60523 Address: 300 Windsor Drive Contact Name: Tom DeSilvia, Director Corporate Compliance The Chamberlain Group LLC (“the applicant”) consent to accept the service of process. An applicant located in the United States may designate itself as the agent for service of process. agent for service of process, regardless of whether the applicant is a domestic or foreign entity. applicant must designate a contact located in the United States for purposes of acting as the applicant’s Certification designating a U.S. agent for service of process. As required by section 2.911(d)(7), the Covered List. equipment and video surveillance equipment produced by entities identified on the Commission’s the Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment that poses an unacceptable risk to national security or the safety of U.S. persons. Specifically, Commission adopted new FCC requirements to protect the nation’s networks and supply chains from Pursuant to FCC 22-84 Report and Order and KDB 986446 D01 Covered Equipment v01, the Date: May 30, 2023 Columbia, MD 21046 7435 Oakland Mills Rd Application Processing Branch Equipment Authorization Division TO: Federal Communication Commission

Page 1 of 1 Date: May 30, 2023 The Chamberlain Group LLC 300 Windsor Dr Oak Brook, IL 60523 Tel: 630.993.6306 Fax: 630.516.6863 Email: [email protected] To: Federal Communication Commis sion Equipment Authorization Division Application Processing Branc h 7435 Oakland Mills Rd Columbia, MD 21046 New Product Submittal: FCC ID: HBW2555N for RF compatibility bridge model Homelink Rptr MC Letter of Changes: To whom it may concern, We would like to submit for a new transmitter , Homelink Rptr MC, with FCC ID: HBW2555N. This unit is identical to the Homelink Rptr MC (FCC ID: HBW2555MC) with the exception that the 343 MHz frequency has been removed via a hardware component change. We would appr eciate your prompt attention to the submittal. If there are any questions, please call me at 630-993-8618 or send a fax to 630-516-6863. Sincerely, Thomas DeSilvia Director Corporate Compliance The Chamberlain Group LLC 300 Windsor Dr, Oak Brook, IL 60523

Page 1 of 1 Date: May 30, 2023 The Chamberlain Group LLC 300 Windsor Dr Oak Brook, IL 60523 Tel: 630.993.6306 Fax: 630.516.6863 Email: [email protected] To: Federal Communication Commission Equipment Authorization Division Application Proc essing Branch 7435 Oakland Mills Rd Columbia, MD 21046 FCC ID: HBW2555N for circuit assembly 195D2555N Request for Confidentiality In accordance with 47 C.F.R. Section 0.457 and 0.459, we, Chamberlain Group, hereby request confidentiality for the Schematics, BOM / Parts List, Component Layout, Theory of Operation and Block Diagram presented for certification. In support of the Request for Confidentiality, the following is stated: Enclosed within this application is technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to our disadvantage. To assist in a ssuring that we receive the full value of our product and protect its competitive posture, we respectfully request this grant of confidentiality. I would appreciate your prompt attention to the submittal. If there are any questions, please call me at 630-993-6306 or send a fax to 630-516-6863. Sincere ly, Thomas DeSilvia Director Corporate Compliance The Chamberlain Group LLC 300 Windsor Dr, Oak Brook, IL 60523

This device complies with Part 15 of the FCC rules and Innovation, Science, and Economic Development Canada license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B) / NMB-3 (B) 132B2475-3 Input Rating/Courant: 120V, 60Hz, 35mA 74N3 APPLIANCE CONTROL Country of Origin: Mexico MODEL CHAMBERLAIN IC: 2666A-2555N FCC ID: HBW2555N 195D2555N HOMELINK RPTR MC

1516 Centre Circle, Downers Grove IL 60515 RF EXPOSURE EXHIBIT Manufacturer Name The Chamberlain Group, Inc. Manufacturer Address 300Winsor Oak Brook,IL 60523 Model No. HomelinkRptr MC HVIN 195D2555N Specifications FCC “Code of Federal Regulations” Title 47 Part 1.1307(b) FCC “Code of Federal Regulations” Title 47 Part 2.1093 Industry Canada RSS-102 Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 FCC Reg. Number: 269750 IC Reg. Number: 2987A CAB Identifier: US0107 Test Procedure FCC KDB 447498 D01 General RF Exposure Guidance v06 RSS-102, Issue 5 Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands ANSI/IEEE C95.1-1992, "Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz," Evaluation Distance 20 cm FCC RF Exposure Radio Access Technology ƒ Transmit Frequency (MHz) ERP/P (dBm) ERP/P (mW) ERP/P Exemption Threshold (mW) Exempt /Not Exempt 15.231 315 -26.3 0.002344229 643 Exempt - (B) ISED RF Exposure Radio Access Technology ƒ Transmit Frequency (MHz) EIRP (dBm) EIRP (W) EIRP Exemption Threshold (W) Exempt /Not Exempt Periodic 315 -26.8 0.000 0.668 Exempt

1516 Centre Circle, Downers Grove IL 60515 ANTENNA EXHIBIT Manufacturer Name The Chamberlain Group, Inc. Manufacturer Address 300 Windsor Dr. Oak Brook, IL 60523 Model No. HOMELINK RPTR Specifications FCC “Code of Federal Regulations” Title 47 Part 2.1033(b)(4), 15.203, 15.212, 15.217, 15.219, 15.255 and 15.256 KDB 353028 D01 v01 f01 Industry Canada RSS-GEN Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 FCC Reg. Number: 269750 IC Reg. Number: 2987A CAB Identifier: US0107 Requirement All part 15 applications will need to show how the antenna gain was derived either from a manufacturer data sheet or a measurement. Where the gain of the antenna is inherently accounted for as a result of the measurement, such as field strength measurements on a part 15.249 or 15.231 device, so the gain does not necessarily need to be verified. However, enough information regarding the construction of the antenna shall be provided. Such information maybe photographs, length of wire antenna etc. The antenna gain information shall be made public (not confidential). Any proprietary information such as construction maybe stripped from the gain information report and held confidential. The main antenna information we require is the maximum gain of the antenna for the band of operation. This information must be provided as a data sheet or a measurement report. 8 inch 18 gauge dipole wire antenna.

Engineering Test Report No. 2300855-01 Report Date April 21, 2023 Manufacturer Name The Chamberlain Group LLC Manufacturer Address 300 Windsor Dr Oak Brook, IL 60523 Model No. HOMELINK RPTR Date Received April 20, 2023 Test Dates April 20, 2023 to April 21, 2023 Specifications FCC "Code of Federal Regulations" Title 47 Part 15, Subpart C, Section 15.231(b) Innovation, Science, and Economic Development Canada, RSS-210 Innovation, Science, and Economic Development Canada, RSS-GEN Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 FCC Reg. Number: 269750 IC Reg. Number: 2987A CAB Identifier: US0107 Signature Tested by Javier Cardenas Signature Approved by Raymond J. Klouda, Registered Professional Engineer of Illinois – 44894 PO Number 4900090196 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Elite Electronic Engineering Incorporated certifies that the information contained in this report was obtained under conditions which meet or exceed those specified in the FCC "Code of Federal Regulations" Title 47 Part 15, Subpart C, Section 15.231 and Innovation, Science, and Economic Development Canada, RSS-210 and RSS-Gen test specification(s). The data presented in this test report pertains to the EUT on the test date(s) specified. Any electrical or mechanical modifications made to the EUT subsequent to the specified test date will serve to invalidate the data and void this certification. This report must not be used to claim product certification, approval, or endorsement by A2LA, NIST, or any agency of the Federal Government. Engineering Test Report No. 2300855-01 This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Page 2 of 38 Table of Contents 1. Report Revision History ............................................................................................................................ 3 2. Introduction ............................................................................................................................................... 4 2.1. Scope of Tests .......................................................................................................................................... 4 2.2. Purpose ..................................................................................................................................................... 4 2.3. Identification of the EUT ............................................................................................................................ 4 3. Power Input ............................................................................................................................................... 4 4. Grounding ................................................................................................................................................. 4 5. Support Equipment ................................................................................................................................... 4 6. Interconnect Leads .................................................................................................................................... 4 7. Modifications Made to the EUT ................................................................................................................. 5 8. Modes of Operation ................................................................................................................................... 5 9. Test Specifications .................................................................................................................................... 5 10. Test Plan ................................................................................................................................................... 5 11. Deviation, Additions to, or Exclusions from Test Specifications ............................................................... 5 12. Laboratory Conditions ............................................................................................................................... 5 13. Summary ................................................................................................................................................... 6 14. Sample Calculations ................................................................................................................................. 6 15. Statement of Conformity ........................................................................................................................... 6 16. Certification ............................................................................................................................................... 6 17. Photographs of EUT .....................................…

Text truncated - open the document above for the full version.

Engineering Test Report No. 2104472-02 Rev. A Page 27 of 41 Test Setup for Spurious Radiated Emissions, 30-1000MHz – Antenna Polarization Horizontal Test Setup for Spurious Radiated Emissions, 30-1000MHz – Antenna Polarization Vertical Engineering Test Report No. 2104472-02 Rev. A Page 28 of 41 Test Setup for Spurious Radiated Emissions, Above 1GHz – Antenna Polarization Horizontal Test Setup for Spurious Radiated Emissions, Above 1GHz – Antenna Polarization Vertical