HBW7356Transceiver

                                          !               " #        #$                             #           #   %                &                      '               !"  #$               ( %  ) *+   #          ,          %# $               ( %  ) * & $              +     ,        ' -   '   .,$/.$01,2 +3   4 5 $             /02   "/. ##           6 %    5 07,                 5 07,     $  #        #   (  "$        &              (  " #    '            $          #(     *             &    #                 % / 0              NOTICE NOTICE  )' ' ' % " (5 8   $         " #       +&     (  +&     *,     '   8#     &   (  +&     * % " " 5 /          9          # % " *  (  " 5      %        ,                         5                            0/$"     :""$  "  ($"*&        ' 6     %          3,+,0//3,.,.,7$" +;+,.     "   :"".  3    /  &       4(<*  '         (=*  '          '              (    + "   '   .,$/.$01,2+34507,    5$            #   %  45,  /02 7=!<)  5/0/      ' =<=>:(<!!>"*         '                   '$          '   (?*,       7=!<)            Batteries Screws (2)   '    ', 

845 Larch Ave. Elmhurst, IL 60126 Phone 630.993.6306 Fax 630.530.6140 Email: [email protected] May 6, 2011 Federal Communications Commission EQUIPMENT APPROVAL SERVICES PO Box 358315 Pittsburgh, PA 15251-5315 Re: FCC ID: HBW7356 Request for Confidentiality In accordance with 47 C.F.R. Section 0.459, we, The Chamberlain Group, Inc., hereby request confidentiality for the block diagram, schematic and product description presented for certification. In support of the Request for Confidentiality, the following is stated: Enclosed within this application is technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to our disadvantage. To assist in assuring that we receive the full value of our product and protect its competitive posture, we respectfully request this grant of confidentiality. Sincerely, THE CHAMBERLAIN GROUP, INC. Barbara Kelkhoff Manager, Regulatory Affairs

100W Max26W Max WARNING • AVERTISSEMENT WARNING: To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric and battery power BEFORE performing ANY maintenance. AVERTISSEMENT: Pour éviter des BLESSURES GRAVES ou la MORT par électrocution, débrancher l’alimentation électrique et de batterie AVANT TOUTE intervention de maintenance. PART NO.: ASSEMBLED IN MEXICO CHAMBERLAIN GROUP INC. ELMHURST IL, 60126, USA DATE: IC: 2666A - FCC ID: Artwork: 132LA2759-00-A 6.2" x 1.85" x 0.12" (W x H x R) Shown at 100% ECN: 05783 22 March 2011 132B2759 TO PROGRAM REMOTE CONTROL 1. Press and release the LEARN button. 2. Within 30 seconds, press and HOLD remote control button. 3. When garage door opener light flashes, release remote control button. TO ERASE ALL CODES 1. Press and HOLD the LEARN button for 6 seconds. The LED will turn ON. 2. Release the LEARN button when LED turns OFF. PROGRAMMATION POUR CHAQUE TÉLÉCOMMANDE 1. Appuyez sur le bouton APPRENTISSAGE et relâchez. 2. Dans les 30 secondes, pesez sur le bouton-poussoir de la télécommande. 3. Dès que la lampe de l’ouvre-porte de garage clignote, relâchez le bouton de la télécommande. POUR EFFACER TOUS LES CODES 1. Pesez sur le bouton APPRENTISSAGE pendant au moins 6 secondes. La lampe-témoin s’allumera. 2. Relâchez le bouton APPRENTISSAGE dès que la lampe-témoin s’éteint. Learn Button Bouton Apprentissage Learn LED lampe-témoin 100W Max26W Max WARNING • AVERTISSEMENT WARNING: To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric and battery power BEFORE performing ANY maintenance. AVERTISSEMENT: Pour éviter des BLESSURES GRAVES ou la MORT par électrocution, débrancher l’alimentation électrique et de batterie AVANT TOUTE intervention de maintenance. PART NO.: ASSEMBLED IN MEXICO CHAMBERLAIN GROUP INC. ELMHURST IL, 60126, USA DATE: IC: 2666A - FCC ID: Artwork: 132LA2759-00-A 6.2" x 1.85" x 0.12" (W x H x R) Shown at 100% ECN: 05783 22 March 2011 132B2759 TO PROGRAM REMOTE CONTROL 1. Press and release the LEARN button. 2. Within 30 seconds, press and HOLD remote control button. 3. When garage door opener light flashes, release remote control button. TO ERASE ALL CODES 1. Press and HOLD the LEARN button for 6 seconds. The LED will turn ON. 2. Release the LEARN button when LED turns OFF. PROGRAMMATION POUR CHAQUE TÉLÉCOMMANDE 1. Appuyez sur le bouton APPRENTISSAGE et relâchez. 2. Dans les 30 secondes, pesez sur le bouton-poussoir de la télécommande. 3. Dès que la lampe de l’ouvre-porte de garage clignote, relâchez le bouton de la télécommande. POUR EFFACER TOUS LES CODES 1. Pesez sur le bouton APPRENTISSAGE pendant au moins 6 secondes. La lampe-témoin s’allumera. 2. Relâchez le bouton APPRENTISSAGE dès que la lampe-témoin s’éteint. Learn Button Bouton Apprentissage Learn LED lampe-témoin 100W Max26W Max WARNING • AVERTISSEMENT WARNING: To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric and battery power BEFORE performing ANY maintenance. AVERTISSEMENT: Pour éviter des BLESSURES GRAVES ou la MORT par électrocution, débrancher l’alimentation électrique et de batterie AVANT TOUTE intervention de maintenance. PART NO.: ASSEMBLED IN MEXICO CHAMBERLAIN GROUP INC. ELMHURST IL, 60126, USA DATE: IC: 2666A - FCC ID: Artwork: 132LA2759-00-A 6.2" x 1.85" x 0.12" (W x H x R) Shown at 100% ECN: 05783 22 March 2011 132B2759 TO PROGRAM REMOTE CONTROL 1. Press and release the LEARN button. 2. Within 30 seconds, press and HOLD remote control button. 3. When garage door opener light flashes, release remote control button. TO ERASE ALL CODES 1. Press and HOLD the LEARN button for 6 seconds. The LED will turn ON. 2. Release the LEARN button when LED turns OFF. PROGRAMMATION POUR CHAQUE TÉLÉCOMMANDE 1. Appuyez sur le bouton APPRENTISSAGE et relâchez. 2. Dans les 30 secondes, pesez sur le bouton-poussoir de la télécommande. 3. Dès que la lampe de l’ouvre-porte de garage clignote, relâchez le bouton de la télécommande. POUR EFFACER TOUS LES CODES 1. Pesez sur le bouton APPRENTISSAGE pendant au moins 6 secondes. La lampe-témoin s’allumera. 2. Relâchez le bouton APPRENTISSAGE dès que la lampe-témoin s’éteint. Learn Button Bouton Apprentissage Learn LED lampe-témoin

For The Chamberlain Group, Inc. 845 Larch Ave. Elmhurst, IL 60126 P.O. Number 868590 Date Received October 8, 2010 Date Tested October 11, 2010 through October 14, 2010 Test Personnel Mark E. Longinotti Specification FCC "Code of Federal Regulations" Title 47, Part 15, Subpart C, Sections 15.207 and 15.247 for Frequency Hopping Spread Spectrum Intentional Radiators Operating within the bands 902-928MHz FCC “Code of Federal Regulations” Title 47, Part15, Subpart 15B, Section 15.107 and 15.109 for Receivers Industry Canada RSS-210 Industry Canada RSS-GEN Test Report By: Mark E. Longinotti EMC Engineer Requested By: Hank Sieradzki The Chamberlain Group, Inc. Approved By: Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Engineering Test Report No. 1003199-01 Measurement of RF Interference from an ID 7356 Transceiver Logic Board Assembly Transceiver Elite Electronic Engineering Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 1003199-01 THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 82 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. TABLE OF CONTENTS .............................................................................................................................................. 2 1 INTRODUCTION ............................................................................................................................................... 5 1.1 Scope of Tests .......................................................................................................................................... 5 1.2 Purpose ..................................................................................................................................................... 5 1.3 Deviations, Additions and Exclusions ....................................................................................................... 5 1.4 EMC Laboratory Identification .................................................................................................................. 5 1.5 Laboratory Conditions ............................................................................................................................... 5 2 APPLICABLE DOCUMENTS ............................................................................................................................ 5 3 EUT SET-UP AND OPERATION ...................................................................................................................... 6 3.1 General Description .................................................................................................................................. 6 3.1.1 Power Input .......................................................................................................................................... 6 3.1.2 Peripheral Equipment ........................................................................................................................... 6 3.1.3 Interconnect Cables ............................................................................................................................. 6 3.1.4 Grounding ............................................................................................................................................. 6 3.2 Operational Mode ..................................................................................................................................... 6 3.3 EUT Modifications ..................................................................................................................................... 6 4 TEST FACILITY AND TEST INSTRUMENTATION .......................................................................................... 6 4.1 Shielded Enclosure ................................................................................................................................... 6 4.2 Test Instrumentation ................................................................................................................................. 6 4.3 Calibration Traceability ............................................................................................................................. 7 4.4 Measurement Uncertainty ......................................................................................................................... 7 5 TEST PROCEDURES ....................................................................................................................................... 7 5.1 Receiver .................................................................................................................................................... 7 5.1.1 Powerline Conducted Emissions .......................................................................................................... 7 5.1.1.1 Requirements .............................................................................................................................. 7 5.1.1.2 Procedures .................................................................................................................................. 7 5.1.1.3 Results ......................................................................................................................................... 8 5.1.2 Radiated Measurements ...................................................................................................................... 8 5.1.2.1 Requirements .............................................................................................................................. 8 5.1.2.2 Procedures .................................................................................................................................. 8 5.1.2.3 Results ...................................................................................................…

Text truncated - open the document above for the full version.

Engineering Test Report No. 1003199-01 Page 19 of 82 Figure 2 Test Setup for Conducted Emissions Engineering Test Report No. 1003199-01 Page 20 of 82 Figure 3 Test Setup for Radiated Emissions – 30MHz to 1GHz, Horizontal Polarization Test Setup for Radiated Emissions – 30MHz to 1GHz, Vertical Polarization Engineering Test Report No. 1003199-01 Page 21 of 82 Figure 4 Test Setup for Radiated Emissions – 1GHz to 10GHz, Horizontal Polarization Test Setup for Radiated Emissions – 1GHz to 10GHz, Vertical Polarization