HD5-CCB00ACharge and Communication Base

Voyager™ 1200g/1202g/1202g-BF Single-Line Laser Bar Code Scanner User’s Guide Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII.  2010-2016 Honeywell International Inc. All rights reserved. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners. Web Address: www.honeywellaidc.com Microsoft® Windows® and the Windows logo are trademarks or registered trademarks of Microsoft Corporation. The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners. i Customer Support Technical Assistance ............................................................................................................ iii Product Service and Repair .................................................................................................. iii Limited Warranty ................................................................................................................... iii Send Feedback ..................................................................................................................... iii Chapter 1 - Getting Started About This Manual ...............................................................................................................1-1 Unpacking Your Device .......................................................................................................1-1 Connecting the Device .........................................................................................................1-1 Connecting with USB .....................................................................................................1-1 Connecting with Keyboard Wedge.................................................................................1-2 Connecting with RS232 Serial Port................................................................................1-4 Connecting with RS485..................................................................................................1-5 Reading Techniques ............................................................................................................1-6 Menu Bar Code Security Settings ........................................................................................1-6 Setting Custom Defaults ......................................................................................................1-6 Resetting the Custom Defaults ............................................................................................1-7 Chapter 2 - Programming the Interface Introduction ..........................................................................................................................2-1 Programming the Interface - Plug and Play .........................................................................2-1 Keyboard Wedge ...........................................................................................................2-1 IBM PS2 Keyboard.........................................................................................................2-1 RS232 Serial Port ..........................................................................................................2-1 RS485 ............................................................................................................................2-2 OPOS Mode...................................................................................................................2-2 USB IBM SurePos..........................................................................................................2-3 IBM Secondary Interface................................................................................................2-3 USB PC or Macintosh Keyboard....................................................................................2-4 USB HID.........................................................................................................................2-4 HID Fallback Mode.........................................................................................................2-4 USB Serial Commands ........................................................................................................2-5 USB Serial......................................................................................................................2-5 CTS/RTS Emulation.......................................................................................................2-5 ACK/NAK Mode .............................................................................................................2-6 Communication Timeout ................................................................................................2-6 NAK Retries ...................................................................................................................2-6 Support BEL/CAN in ACK/NAK......................................................................................2-7 Verifone ® Ruby Terminal Default Settings...................................................................…

Text truncated - open the document above for the full version.

Page: 1 of 6 (1) EUT Photo (2) EUT Photo Page: 2 of 6 (3) EUT Photo (4) EUT Photo Page: 3 of 6 (5) EUT Photo (6) EUT Photo Page: 4 of 6 (7) EUT Photo (8) EUT Photo Page: 5 of 6 (9) EUT Photo (10) EUT Photo Page: 6 of 6 (11) EUT Photo

Page: 1 of 2 (1) EUT Photo (2) EUT Photo Page: 2 of 2 (3) EUT Photo

SAR Exemption Evaluation Report Product Name : Charge and Communication Base Model No. : CCB00-010BT FCC ID : HD5-CCB00A Applicant : HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions Address : 9680 OLD BAILES RD FORT MILL SC 29707-7539,USA Date of Receipt : Apr. 08, 2020 Issued Date : May. 13, 2020 Report No. : 2040167R-RF-US-P20V02 Report Version : V1.0 The test results presented in this report relate only to the object tested. The measurement result is considered in conformance with the requirement if it is within the prescribed limit, It is not necessary to account the uncertainty associated with the measurement result, unless the specification, standard or customer have special requirements This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory This report is not used for social proof in China (or Mainland China) market. Report No: 2040167R-RF-US-P20V02 Page: 2 of 5 Te s t R e p o r t C e r t i f i c a t i o n Issued Date: May. 13, 2020 Report No.: 2040167R-RF-US-P20V02 Product Name : Charge and Communication Base Applicant : HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions Address : 9680 OLD BAILES RD FORT MILL SC 29707-7539,USA Manufacturer : 1. HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions 2. Metro(Suzhou)Technologies Co.,Ltd Address : 1. 9680 OLD BAILES RD FORT MILL SC 29707-7539,USA 2. No.221 Xinghai street China-Singapore Suzhou Industrial Park Model No. : CCB00-010BT FCC ID : HD5-CCB00A EUT Voltage : 4.75~5.25 Vdc Applicable Standard : KDB 447498 D01v06 Test Result : Complied Performed Location : DEKRA Testing & Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Designation Number: CN1199 Documented By : (Project Assistant: Kitty Li) Reviewed By : (Technical Supervisor: Frank He) Approved By : (Supervisor: Jack Zhang) Report No: 2040167R-RF-US-P20V02 Page: 3 of 5 1. RF Exposure Evaluation 1.1. Limits According to KDB 447498 D01 General RF Exposure Guidance v06 4.3.1 Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following, and as illustrated in Appendix B: a) [Power allowed at numeric threshold for 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW, at 100 MHz to 1500 MHz b) [Power allowed at numeric threshold for 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) The 1-g and 10-g SAR test exclusion thresholds for below 100 MHz at test separation distances ≤ 50 mm are determined by: a) The power threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm b) The power threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Note: when the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Report No: 2040167R-RF-US-P20V02 Page: 4 of 5 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. 1.3. Test Result of RF Exposure Evaluation Product : Charge and Communication Base Test Item : RF Exposure Evaluation Test Site : AC-6  Antenna Information Antenna model N/A Antenna Delivery 1*TX+1*RX 2*TX+2*RX 3*TX+3*RX Antenna technology SISO MIMO Basic CDD Beam-forming Antenna Type External Dipole Internal PIFA PCB Ceramic Chip Antenna Stamping Antenna Metal plate type F antenna Monopole antenna Antenna Gain -0.5 dBi Report No: 2040167R-RF-US-P20V02 Page: 5 of 5 Based on The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm and the formula below: The Maximum tune-up power is 0.5dB higher than Maximum Measurement power, so the maximum conducted power we used to calculate RF exposure is 5.41dBm. Band Exposure Condition Pmax Pmax Distance f(GHz) calculation result Stand-alone Test exclusion threshold SAR Test (dBm) (mw) (mm) BT Body 5.41 3.48 5 2.48 1.10 3.00 No Conclusion: 2.4GHz SAR was not required. The End

Test Report FCC Part15 Subpart C& RSS-247 Issue 2 Product Name : Charge and Communication Base Model No. : CCB00-010BT FCC ID : HD5-CCB00A IC : 1693B-CCB00A Applicant : HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions Address : 9680 OLD BAILES RD FORT MILL SC 29707-7539,USA Date of Receipt : Apr. 08, 2020 Test Date : Apr. 09, 2020 ~ May. 12, 2020 Issued Date : May. 13, 2020 Report No. : 2040167R-RF-US-P06V01 Report Version : V1.0 The test results presented in this report relate only to the object tested. The measurement result is considered in conformance with the requirement if it is within the prescribed limit, It is not necessary to account the uncertainty associated with the measurement result, unless the specification, standard or customer have special requirements This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory This report is not used for social proof in China (or Mainland China) market. Report No.: 2040167R-RF-US-P06V01 Page: 2 of 110 Te s t R e p o r t C e r t i f i c a t i o n Issued Date: May. 13, 2020 Report No.: 2040167R-RF-US-P06V01 Product Name : Charge and Communication Base Applicant : HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions Address : 9680 OLD BAILES RD FORT MILL SC 29707-7539,USA Manufacturer : 1. HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions 2. Metro(Suzhou)Technologies Co.,Ltd Address : 1. 9680 OLD BAILES RD FORT MILL SC 29707-7539,USA 2. No.221 Xinghai street China-Singapore Suzhou Industrial Park Model No. : CCB00-010BT Trademark : Honeywell FCC ID : HD5-CCB00A IC : 1693B-CCB00A EUT Voltage : 4.75~5.25 Vdc Applicable Standard : FCC CFR Title 47 Part 15 Subpart C KDB 558074 D01v05r02 ANSI C63.10: 2013 RSS-Gen Issue 5/RSS-247 Issue 2 Test Result : Complied Performed Location : DEKRA Testing & Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Designation Number: CN1199; ISED CAB identifier: CN0040 Documented By : (Project Assistant: Kitty Li) Reviewed By : (Technical Supervisor: Frank He) Approved By : (Supervisor: Jack Zhang) Report No.: 2040167R-RF-US-P06V01 Page: 3 of 110 TABLE OF CONTENTS Description Page 1. General Information ................................................................................................... 7 1.1. EUT Description ......................................................................................................... 7 1.2 Antenna information ................................................................................................... 9 1.3 Mode of Operation ................................................................................................... 10 1.4 Tested System Details .............................................................................................. 11 1.5 Configuration of Tested System ............................................................................... 12 1.6 EUT Exercise Software ............................................................................................ 13 2. Technical Test ........................................................................................................... 14 2.1. Summary of Test Result ........................................................................................... 14 2.2. Test Environment ..................................................................................................... 16 3. Conducted Emission ................................................................................................ 17 3.1. Test Equipment ........................................................................................................ 17 3.2. Test Setup ................................................................................................................ 17 3.3. Limit.......................................................................................................................... 18 3.4. Test Procedure ......................................................................................................... 18 3.5. Uncertainty ............................................................................................................... 18 3.6. Test Result ............................................................................................................... 19 4. Emissions in restricted frequency bands .................................................................. 21 4.1. Test Equipment ........................................................................................................ 21 4.2. Test Setup ................................................................................................................ 22 4.3. Limit.......................................................................................................................... 23 4.4. Test Procedure ......................................................................................................... 26 4.5. Uncertainty ............................................................................................................... 26 4.6. Test Result ............................................................................................................... 27 5. 20dB Bandwidth ....................................................................................................... 47 5.1 Test Equipment ........................................................................................................ 47 5.2 Test Setup ................................................................................................................ 47 5.3 Limit.......................................................................................................................... 47 5.4 Test Procedure ...............................................................................…

Text truncated - open the document above for the full version.

FCC Part15.247&IC Test Setup Photograph Description: Conducted emission Test Setup Description: Radiated Emission Test Setup for Below 1GHz Description: Radiated Emission Test Setup for 1~18GHz Description: Radiated Emission Test Setup for Above 18GHz