HD5-DEX-BLE-10DEX Adaptor

DEX Adapter Model DEX-BLE-10 Quick Start Guide DEX-BLE-EN-QS-01 Rev A 8/20 Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 2 Out of the Box Make sure that your shipping box contains these items: • DEX wireless adapter (Model DEX-BLE-10) • Rechargeable 3.7 VDC Li-ion battery (Model DEX-10-BATTERY) • USB charge cable, type A to micro B • Power adapter with regional plug • Regulatory Sheet If any of these items are missing or appear damaged, contact your Customer Account Representative. Keep the original packaging in the event that you need to return the DEX adapter for service or if you want to store it while not in use. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 3 Adapter Features DEX Cable Bluetooth Connection Status Indicator On/Off Power Buttons Battery Cover Belt Clip NFC Antenna Micro USB Cover T5 Torx® Screw Battery Charge Status Indicator Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 4 About the Battery The DEX-BLE-10 ships with an installed Li-ion 3.7 VDC, 750 mAh battery manufactured for Honeywell International Inc. The operating temperature is -20°C (-4 °F) to 60°C (140 °F) Charge the Battery The DEX-BLE-10 ships with a partially charged battery. Charge the battery for a minimum of 4 hours before initial use. Use only Honeywell Li-ion battery pack model DEX-10-BATTERY. Utilisez uniquement des batteries Honeywell Li-ion modèle DEX-10-BATTERY. Ensure all components are dry prior to placing the battery in the DEX-BLE-10. Mating wet components may cause damage not covered by the warranty. Assurez-vous que tous les composants sont secs avant d’insérer la batterie dans l’DEX-BLE-10. L’insertion de composants humides risque de provoquer des dommages non couverts par la garantie. We recommend the use of Honeywell accessories and power adapters. Use of any non-Honeywell accessories or power adapters may cause damage not covered by the warranty. Nous recommandons d’utiliser des accessoires et des adaptateurs secteur de marque Honeywell. L’utilisation de tout accessoire ou adaptateur secteur d’une autre marque est susceptible de provoquer des dommages non couverts par la garantie. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 5 USB Charge Cable The USB cable provides two options for charging the DEX wireless adapter. Note:The micro USB connector on the DEX-BLE-10 only supports charging the battery and cannot be used for data transfer. Option 1: Charging From a Power Outlet Use only a UL Listed power supply that has been qualified by Honeywell with an output rated at 5VDC and 2A with the device. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 6 Option 2: Charging From a USB Port on a Host Device Ensure all components are dry prior to mating the DEX-BLE-10 and battery with peripheral devices. Mating wet components may cause damage not covered by the warranty. Assurez-vous que tous les composants sont secs avant de connecter le DEX et la batterie à les périphériques. L’insertion de composants humides risque de provoquer des dommages non couverts par la garantie. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 7 Turn Power On/Off To turn the DEX-BLE-10 on, press the “ON” button. To turn the DEX-BLE-10 on, press the “OFF” button. Note:The DEX-BLE-10 automatically powers OFF after 5-minutes of inactivity. Connect the DEX-BLE-10 The DEX adapter easily connects to direct store delivery (DSD) DEX/UCS store systems and Vending Machines. 1.Turn ON the DEX-BLE-10. 2.Pull the connector out of the molded side cavity of the adapter. 3.Insert the connector into the receiving system. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 8 Pair the DEX-BLE-10 with a Mobile Computer The DEX Wireless Adapter supports Honeywell devices on Android 6 and higher. To pair the DEX-BLE-10: 1.Verify the mobile computer is turned on and Bluetooth and NFC are enabled. 2.Turn ON the DEX-BLE-10. 3.Place the DEX-BLE-10 back to back with the mobile computer. The NFC antenna is on the back of the DEX wireless adapter. The mobile computer initiates the pairing process with the adapter. 4.Follow the on-screen prompts to establish a connection and transfer data. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 9 Bluetooth Communication Status The blue LED indicates the communication between the DEX-BLE-10 and another device using Bluetooth™ technology. Blue LED StatusBluetooth Communication Status SolidNot paired, but discoverable to other devices. Fast FlashAttempting connection with other device. Slow FlashConnection established with other device. * LED is active until the adapter automatically powers down due to inactivity or is manually turned OFF. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft, Not for Release, For Review Purposes Only 10 Battery Status The green LED indicates the status of the battery charge. Note:The LED behavior differs if the DEX-BLE-10 is connected to an external power source (e.g., power cable and wall charger) instead of using battery power. PowerLED StatusDescription External (Cable/ Power Source) FlashBattery charging External (Cable/ Power Source) Solid Battery fully charged BatteryFlash 5-seconds On 5-seconds Off* Battery Low, Less than 20% BatteryOff*Battery Charge is between 20% and 80%. BatterySolid 5-seconds On 5-seconds Off* Battery Fully Charged * LED status after initial device power on sequence. Preliminary Draft, Not for Release, For Review Purposes Only Preliminary Draft…

Text truncated - open the document above for the full version.

Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Declaration of Authorization We Name: Honeywell International Inc Honeywell Safety and Productivity Solutions Address: 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Declare that: Name Representative of agent: Marlin Chen Agent Company name: MRT Technology (Suzhou) Co., Ltd Address: D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone, City: Suzhou Country China is authorized to apply for Certification of the following product(s): Product description: DEX Adaptor Type designation: DEX-BLE-10 Trademark: Honeywell IC: 1693B-DEXBLE10 FCC ID: HD5-DEX-BLE-10 on our behalf. Signature: Name/Title: Mandana Salahshour / Compliance Manager Honeywell International Inc TEL: +1 8038358190-8190 Email: [email protected] 2020-07-14

Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: HD5-DEX-BLE-10 Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until (180 days): External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Signature Date: 2020/07/14 Name/Title: Mandana Salahshour / Compliance Manager TEL: +1 8038358190-8190 Email: [email protected]

Report No.: 2006RSU082-UE 1 of 5 EUT Photograph (1) EUT Photo (2) EUT Photo Report No.: 2006RSU082-UE 2 of 5 (3) EUT Photo (4) EUT Photo Report No.: 2006RSU082-UE 3 of 5 (5) EUT Photo (6) EUT Photo Report No.: 2006RSU082-UE 4 of 5 (7) EUT Photo (8) EUT Photo Report No.: 2006RSU082-UE 5 of 5 (9) EUT Photo (10) EUT Photo

Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Label and Label Location

Report No.: 2006RSU082-UE 1 of 5 EUT Photograph (1) EUT Photo (2) EUT Photo - Battery 1# Report No.: 2006RSU082-UE 2 of 5 (3) EUT Photo - Battery 1# (4) EUT Photo - Battery 2# Report No.: 2006RSU082-UE 3 of 5 (5) EUT Photo - Battery 2# (6) EUT Photo Report No.: 2006RSU082-UE 4 of 5 (7) EUT Photo (8) EUT Photo Report No.: 2006RSU082-UE 5 of 5 (9) EUT Photo

MRT Technology (Suzhou) Co., Ltd Report No.: 2006RSU082-U2 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 07-22-2020 Page Number: 1 of 6 RF Exposure Evaluation Declaration FCC ID: HD5-DEX-BLE-10 APPLICANT: Honeywell International Inc Honeywell Safety and Productivity Solutions Application Type: Certification Product: DEX Adaptor Model No.: DEX-BLE-10 Brand Name: Honeywell FCC Classification: Digital Transmission System (DTS) Reviewed By: ( Jame Yuan ) Approved By: ( Robin Wu ) The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standards through the calibration of the equipment and evaluated measurement uncertainty herein. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2006RSU082-U2 Page Number: 2 of 6 Revision History Report No. Version Description Issue Date Note 2006RSU082-U2 Rev. 01 Initial Report 07-22-2020 Valid Report No.: 2006RSU082-U2 Page Number: 3 of 6 1. RF Exposure Evaluation 1.1. Limits SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The equation and threshold in Note 1 must be applied to determine SAR test exclusion. MHz 5 10 15 20 25 mm 150 39 77 116 155 194 SAR Test Exclusion Threshold (mW) 300 27 55 82 110 137 450 22 45 67 89 112 835 16 33 49 66 82 900 16 32 47 63 79 1500 12 24 37 49 61 1900 11 22 33 44 54 2450 10 19 29 38 48 3600 8 16 24 32 40 5200 7 13 20 26 33 5400 6 13 19 26 32 5800 6 12 19 25 31 MHz 30 35 40 45 50 mm 150 232 271 310 349 387 SAR Test Exclusion Threshold (mW) 300 164 192 219 246 274 450 134 157 179 201 224 835 98 115 131 148 164 900 95 111 126 142 158 1500 73 86 98 110 122 1900 65 76 87 98 109 2450 57 67 77 86 96 3600 47 55 63 71 79 5200 39 46 53 59 66 5400 39 45 52 58 65 5800 37 44 50 56 62 Report No.: 2006RSU082-U2 Page Number: 4 of 6 Note: The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] * [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where ⚫ f(GHz) is the RF channel transmit frequency in GHz ⚫ Power and distance are rounded to the nearest mW and mm before calculation ⚫ The result is rounded to one decimal place for comparison ⚫ 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°C and 78% RH. Report No.: 2006RSU082-U2 Page Number: 5 of 6 1.3. Test Result of RF Exposure Evaluation Product DEX Adaptor Test Item RF Exposure Evaluation Antenna Gain: The maximum Gain measured in fully anechoic chamber is -1.56dBi for 2.4GHz in logarithm scale. Output Power into Antenna: Test Mode Frequency Band (MHz) Maximum output power to antenna (mW) E.I.R.P. (mW) SAR Test Exclusion Threshold (mW) Bluetooth 2402 ~ 2480 0.463 0.324 10 Note: Max conducted power = -3.34 dBm = 0.463 mW Max E.I.R.P. = -3.34 dBm + (-1.56 dBi) = 0.324 mW Per FCC KDB 447498 D01v06, the SAR exclusion threshold for distances<50mm is defined by the following equation: Based on the maximum conducted power of Bluetooth and the antenna to use separation distance, Bluetooth SAR was not required; [(0.463mW/5)* √2.402] = 0.144 < 3.0 The Max P d = 0.144 < 3.0 Note: When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. The End Report No.: 2006RSU082-U2 Page Number: 6 of 6 Appendix A - EUT Photograph Refer to “2006RSU082-UE” file.

MRT Technology (Suzhou) Co., Ltd Report No.: 2006RSU082-U1 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 07-22-2020 1 of 56 FCC ID: HD5-DEX-BLE-10 IC: 1693B-DEXBLE10 Applicant: Honeywell International Inc Honeywell Safety and Productivity Solutions Application Type: Certification Product: DEX Adaptor Model No.: DEX-BLE-10 Brand Name: Honeywell FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15 Subpart C (Section 15.247) ISED Rule(s): RSS-247 Issue 2, RSS-Gen Issue 5 Test Procedure(s): ANSI C63.10-2013 Test Date: July 13 ~ 21 2020 MEASUREMENT REPORT FCC PART 15.247 / ISED RSS-247 Reviewed By: ( Jame Yuan ) Approved By: ( Robin Wu ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2006RSU082-U1 2 of 56 Revision History Report No. Version Description Issue Date Note 2006RSU082-U1 Rev. 01 Initial Report 07-22-2020 Valid Report No.: 2006RSU082-U1 3 of 56 CONTENTS Description Page 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope ........................................................................................................................... 6 1.2. MRT Test Location ....................................................................................................... 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Feature of Equipment under Test ................................................................................. 7 2.2. Product Specification Subjective to this Report ............................................................. 7 2.3. Working Frequencies for this report .............................................................................. 8 2.4. Duty Cycle .................................................................................................................... 8 2.5. Configuration of Tested System .................................................................................... 9 2.6. Test Software ............................................................................................................... 9 2.7. EMI Suppression Device(s)/Modifications ..................................................................... 9 2.8. Test Environment Condition .......................................................................................... 9 2.9. Labeling Requirements ............................................................................................... 10 3. DESCRIPTION OF TEST ....................................................................................................... 11 3.1. Evaluation Procedure .................................................................................................. 11 3.2. AC Line Conducted Emissions .................................................................................... 11 3.3. Radiated Emissions .................................................................................................... 12 4. ANTENNA REQUIREMENTS ................................................................................................ 13 5. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 14 6. MEASUREMENT UNCERTAINTY ......................................................................................... 16 7. TEST RESULT ...................................................................................................................... 17 7.1. Summary .................................................................................................................... 17 7.2. Occupied Bandwidth Measurement ............................................................................ 18 7.2.1. Test Limit ................................................................................................................ 18 7.2.2. Test Procedure used ............................................................................................... 18 7.2.3. Test Setting ............................................................................................................. 18 7.2.4. Test Setup ............................................................................................................... 19 7.2.5. Test Result .............................................................................................................. 20 7.3. Output Power Measurement ....................................................................................... 22 7.3.1. Test Limit ................................................................................................................ 22 7.3.2. Test Procedure Used .............................................................................................. 22 7.3.3. Test Setting ............................................................................................................. 22 7.3.4. Test Setup ............................................................................................................... 23 Report No.: 2006RSU082-U1 4 of 56 7.3.5. Test Result of Output Power ................................................................................... 24 7.4. Power Spectral Density Measurement ........................................................................ 25 7.4.1. Test Limit ................................................................................................................ 25 7.4.2. Test…

Text truncated - open the document above for the full version.

Report No.: 2006RSU082-UT 1 of 3 Test Setup Photograph Test Mode 1 Description: Front View of Conducted Emission Test Setup Test Mode 1 Description: Back View of Conducted Emission Test Setup Report No.: 2006RSU082-UT 2 of 3 Description: Conducted Test Setup Test Mode 1 Description: Radiated Spurious Emission Test Setup Below 1GHz Report No.: 2006RSU082-UT 3 of 3 Test Mode 1 Description: Radiated Spurious Emission Test Setup Above 1GHz