HD5DPM01Handheld Reader for Industrial ID

Instructions: Two-sided, four-color. Fold in thirds. Finished size 5.66 x 10 inches (folded) 17 x 10 inches (unfolded) Use coated 80# cover stock 6320 6320 6300 1 2 3 4 5 6 1 Status: Red: read failed Green: read succeeded Blue: cordless link up Blinking red: low battery Trigger (press and hold to read) Charge: Steady green: fully charged Blinking green: charging Status: Steady red: connected to power Blinking red: data transfer Power Data (RS-232, USB, PS/2 Keyboard) Cable release (corded unit) Inserting device in base establishes Bluetooth® link and charges battery. Scan USB Serial or RS-232 Serial configuration code from the back of this document. Allow the Windows Found New Hardware Wizard to run. Select Automatic driver installation. When prompted during driver load, click Continue Anyway. 1. 2. Use setup tool to configure reader (shortcut on desktop) Common tasks Controls and information Question and Answer help 1. 2. 3. 2 2 1 2 3 Install Software Connect Device Place in Base (Cordless Only) Load USB Driver (USB Only) Scan Connection Code Start Setup Tool 1 USB: 42206416-01 RS-232: 42206139-04 USB: 42206161-01 RS-232: 42203758-03S Insert CD-ROM and install software (follow prompts). Run setup.exe if installer does not start automatically. You must have Administrator privileges to install. .NET Framework is installed if required. When prompted, click Continue Anyway. 1. • • • 2. Connect base or device to PC using USB or Serial cable (PS/2 keyboard cable is not supported by setup tool.) Connect base or device to power supply. 1. 2. hhp_qr.indd 11/26/2006 10:22:55 AM i Instructions: Two-sided, four-color. Fold in thirds. Finished size 5.66 x 10 inches (folded) 17 x 10 inches (unfolded) Use coated 80# cover stock 6300 Series DPM 6300-20-QS Rev (A) Copyright © 2006 Hand Held Products, Inc. All Rights Reserved. This document may not be copied in whole or in part, nor transferred to any other media or language, without the written permission of Hand Held Products, Inc. The hardware and portions of the software described in this document may be covered by one or more of the U.S. patents. 6300 Corded Imager 6320 Cordless Imager Quick Start Guide 6300 Corded6320 Cordless Product support: http://www.handheld.com/Site.aspx/na/en/services_support/ CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. The battery should be disposed of by a qualified recycler or hazardous materials handler. Do not incinerate the battery or dispose of the battery with general waste materials. NOTE: Any modifications to this device not expressly approved by HANDHELD PRODUCTS, INC. may void your authority to operate it. RS-232 Serial Weight270g (9.5 oz)330g (11.6 oz) Base: 250g (8.8 oz) Operating Temperature -10ºC — 50ºC (14ºF — 122ºF)0ºC — 50ºC (32ºF — 122ºF) Storage Temperature -40ºC — 70ºC (-40ºF — 158ºF)-40ºC — 60ºC (-40ºF — 140ºF) Charging Temperature 5ºC — 40ºC (41ºF — 104ºF) Maximum Humidity 95% (non-condensing) EnvironmentalIP54IP54 Base: IP41 Drop (Impact) 50 drops from 2m (6.5’) to concrete25 drops from 2m (6.5’) to concrete Codes Data Matrix TM (ECC 0, 50, 80, 100, 140, and 200) QR Code UPC/EAN/JAN Interleaved 2 of 5 Code 39, Code 128, and Code 93 Power Consumption 1000 mA @ 5 VDCBase: 800 mA @ 9 VDC Battery Life at 25ºC (77ºF)8h (normal use) PS/2 Keyboard Wedge USB Serial USB Keyboard Soft reset (save settings)Hard reset (discard settings) US EnglishFrench German Connection Keyboard Commands Setups Unlink base station Enable Setup 3 onlyEnable Setup 4 only Enable Setup 1 onlyEnable Setup 2 only See Configuration Codes in setup tool for more languages. 5 mil 10 mil 20 mil 0 - 35 mm (0 - 1.4 in) 13 mil0 - 62mm (0 - 2.4 in) 0 - 55 mm (0 - 2.1 in) 0 - 85 mm (0 - 3.3 in) 20 123 406080mm in Notes Reading Distance 1D Codes 2D Codes hhp_qr.indd 21/26/2006 10:22:59 AM

1
     
      








 
   
   








   
 
        








  ! "
   #   









$ 
  ! "
   # # # #









% % % &      &  '
Letter of Confidentiality Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission ́s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential documents from public disclosure indefinitely. Operational Description Block Diagram Schematics Above mentioned documents contain detailed system and equipment description that are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitors an unfair advantage in the market Aachen, 10.02.2006 Guido Schützeichel, Cognex ID Products Naveen Velagapudi Handheld Products, Inc

1
     
      








 
   
   








   
 
        








  ! "
   #   









$ 
  ! "
   # # # #









% % % &      &  '
External photographs: 6320 from side 6320 from front side 2
     
      








 
   
   








   
 
        








  ! "
   #   









$ 
  ! "
   # # # #









% % % &      &  '
6320 from top 6320 from bottom Battery is inserted here 3
     
      








 
   
   








   
 
        








  ! "
   #   









$ 
  ! "
   # # # #









% % % &      &  '
6320 from back side 6320 with released battery Battery is inserted here

Underlay label Print on Demand at time of manufacture (see notes below): 1.1. Serial Number Generation Overview Serial numbers will be automatically generated sequentially from a single series of numbers. Serial numbers produced using this process will be unique on every unit produced, not just unique to a product family group. Only unique serial numbers will be generated; serial numbers will not be recycled. Serial numbers will include an encoded date stamp and can be used for tracking. A serial number will be 10 digits long and contain only hexadecimal digits. Refer to Table 1 for the format of the serial number and Table 2 for a description of the serial number fields. Table 1. Serial Number Format Year Day of Year Location Sequential Number 0 5 1 2 3 0 1 2 34 Table 2. Serial Number Fields Fields Range Description Year 01 to 99 01 = 2001 Day of Year 001 to 365 001 = January 1 Location 0x0 to 0xF 0 = Hand Held Products NY Sequential Number 0x0001 to 0xFFFF Resets to 1 on each Day of Year change. Blocks of serial numbers can be cached from the network onto local machines so they can operate independently until the network is operational again. Serial number data blocks will be synchronized by the network script. Serial number tracking provides a record of each individual unit manufactured. The manufacturing serial number can be automatically delivered into the company SAP database system. Corded Input: 4.5-12 VDC, .4A Hand Held Products, Inc.Hand Held Products, Inc. www.handheld.comwww.handheld.com g p t f er e u e h r t c h i S i e . . . . TU V R h in e la nd P ro d c u t ey a S t f S P ee g k For P i aten Li t t s ng 57 4 E 13 0 7D21 N 10401 N 10401 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la Class A est conforme a la norme NMB-003 du Canada. S/N ITEM REV HW REV A 05-123-0-1234 S/N ITEM REV DP 6320 6320IDP351S FCC ID: HD5DPM01 IC: 1693B-DPM01

1
     
      








 
   
   








   
 
        








  ! "
   #   









$ 
  ! "
   # # # #









% % % &      &  '
Internal photographs: Open 6320 with imager, illumination and main board Main board 6320 top side 2
     
      








 
   
   








   
 
        








  ! "
   #   









$ 
  ! "
   # # # #









% % % &      &  '
Main board 6320 rear side (w/ Bluetooth module) Open 6320 with main board (rear side) Bluetooth antenna 3
     
      








 
   
   








   
 
        








  ! "
   #   









$ 
  ! "
   # # # #









% % % &      &  '
Open Bluetooth module with antenna

The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-EMC-TR-06-030-V01.00 Page 1 of 61 Date of issue: 03.02.06 Signature: Issue-No.: 01 Author: J.Steinbinder Test engineer Date of delivery: 5.01.06 Checked: W.Zapf Operational manager Testdates: 10.01. – 03.02.06 Pages: 61 ECL-EMC Test Report No.: 06-030 Equipment under test: Hand Held Products 6320 FCC ID: HD5DPM01 IC: 1693B-DPM01 Type of test: FCC Part 15.247 for FHSS systems and Canada RSS-210 Measurement Procedures: ANSI C63.4 (2001) Test result: Passed EMC-Test Report No.: 06-030 The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-EMC-TR-06-030-V01.00 Page 2 of 61 Client: Hand Held Products, Inc. 700 Visions Drive Skaneateles Falls, NY 13153 USA Manufacturer: Hand Held Products, Inc. 700 Visions Drive Skaneateles Falls, NY 13153 USA Testhouse: HERBERG Service Plus GmbH European Compliance Laboratory (ECL) Nordostpark 51 D-90411 Nürnberg Tel.: +49 0911 59835 91 Fax: +49 0911 59835 90 General: The purpose of the performed inspections and tests was to demonstrate that an equipment under defined environmental conditions can survive without irreversible failures and perform according to requirements. This report informs about the results of the EMC tests, it only refers to the equipment under test. No part of this report may be reproduced in any form, without written permission. EMC-Test Report No.: 06-030 The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-EMC-TR-06-030-V01.00 Page 3 of 61 Table of contents 1 INTRODUCTION..............................................................................................................................5 1.1 PURPOSE....................................................................................................................................5 1.2 TEST RESULTS SUMMARY.............................................................................................................5 2 EQUIPMENT UNDER TEST.............................................................................................................6 2.1 EUT DESIGNATION.......................................................................................................................6 2.2 DESCRIPTION...............................................................................................................................6 2.3 CONFIGURATION..........................................................................................................................6 2.3.1 CONNECTIONS......................................................................................................................6 2.3.2 ADDITIONAL INFORMATION......................................................................................................6 2.3.3 USED SOFTWARE..................................................................................................................6 3 NORMATIVE REFERENCES............................................................................................................8 4 DESCRIPTION OF THE EMC TEST CENTRE..................................................................................9 4.1 REGISTRATIONS...........................................................................................................................9 4.2 SEMI ANECHOIC CHAMBER (SAC) W ITH MAXIMUM 10M MEASUREMENT DISTANCE..............................10 4.3 FULLY ANECHOIC CHAMBER (FAC) W ITH MAXIMUM 5M MEASUREMENT DISTANCE...............................11 4.4 FULLY ANECHOIC CHAMBER (FAC2) W ITH MAXIMUM 3M MEASUREMENT DISTANCE.............................12 4.5 FULLY ANECHOIC CHAMBER (STRIPLINE) .......................................................................................13 4.6 SHIELDED TEST CABINS...............................................................................................................14 4.7 INSTRUMENT ROOM....................................................................................................................15 4.8 MEASUREMENT UNCERTAINTY.....................................................................................................16 4.9 GROUND PLAN...........................................................................................................................17 5 MEASUREMENTS..........................................................................................................................19 5.1 CARRIER FREQUENCY SEPARATION §15.247(A) ...............................................................19 5.1.1 RESULTS............................................................................................................................19 5.2 NUMBER OF HOPPING CHANNELS §15.247(A) ..................................................................20 5.2.1 RESULTS............................................................................................................................20 5.3 TIME OF OCCUPANCY (DWELL TIME) §15.247(A) ...............................................................21 5.3.1 RESULTS............................................................................................................................21 5.4 SPECTRUM BANDWITH OF FHSS SYSTEM §15.247(A).......................................................22 5.4.1 RESULTS............................................................................................................................23 5.5 MAXIMUM PEAK OUTPUT POWER(CONDUCTED) §15.247(B)(1).............................................26 5.5.1 RESULTS............................................................................................................................27 5.6 MXIMUM PEAK OUTPUT POWER (RADIATED) §15.247 (B)(1).................................................30 5.6.1 RESULTS...................................................................…

Text truncated - open the document above for the full version.

Test Setup photos : Radiated emission up to 1000 MHz Radiated emission up to 26 GHz EIRP