HD5QC900ABar Code Scanner with BT

Reg-0002 Rev A 2/06 www.handheld.com Reg-0002 Rev A Agency Compliance Statements This device meets or exceeds the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your device. Regulatory and Safety Approvals FCC Class B Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio or television technician for help. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Hand Held Products, Inc. is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Hand Held Products, Inc. The correction is the responsibility of the user. Use only shielded data cables with this system. In accordance with FCC 15.21, changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To maintain compliance with FCC RF exposure guidelines for body-worn operation, do not use accessories that contain metallic components and ensure that the device is at least 15mm (0.6 inches) from the body. Canadian Compliance This Class B digital apparatus compiles with Canadian ICES-003. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide max- imum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. The CE mark on the product indicates that the system has been tested to and conforms with the provisions noted within the 89/336/EEC Electromagnetic Compatibility Directive and the 73/23/EEC Low Voltage Directive. For further information please contact: Hand Held Products, Inc. Nijverheidsweg 9 5627 BT Eindhoven The Netherlands Hand Held Products shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. Bluetooth Qualified Product Bluetooth Qualified Body approved as a Bluetooth Class II radio. ParameterSpecification USAFCC Part 15, Class B CanadaICES-003 European Community EN55022 (CISPR 22) Class B EN55024:1998 EN60950 EN60825-1 ! Reg-0002 Rev A 2/06 www.handheld.com This product is marked with in accordance with the Class II product requirements specified in the R&TTE Directive, 1999/5/EC. The equipment is intended for use throughout the European Community. LED Safety Statement This device has been tested in accordance with IEC60825-1 LED safety, and has been certified to be under the limits of a Class 1 LED device. Laser Eye Safety Statement If the following label is attached to your product, it indicates the product contains a laser engine or laser aimer: UL and cUL Statement UL and cUL listed: UL60950-1 and CSA C22.2 No.60950-1-03. C-Tick Statement Conforms to AUS/NZ 3548. TÜV Statement TÜV or GS marked to EN60950 and EN60825-1. Mexico Certified. Solids and Water Protection This device has a rating of IP41, immunity of foreign particles and dripping water. Patents Please refer to product packaging for patent information. For European Community Users Hand Held Products complies with Directive 2002/69/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE). Waste Electrical and Electronic Equipment Information This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed.In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way. If you need more information on the collection, reuse, and recycling systems, please conta…

Text truncated - open the document above for the full version.

™ User’s Guide Quick Check® 890 Bar Code Verifier Quick Check® ImageData Disclaimer Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Hand Held Products to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Hand Held Products. Hand Held Products shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hand Held Products. ©2006 Hand Held Products, Inc. All rights reserved. Web Address: www.handheld.com Quick Check ® is a registered trademark of Hand Held Products, Inc. Microsoft, Windows, Windows Mobile, Windows NT, Windows 2000, Windows ME, Windows XP, ActiveSync, Outlook, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation. The Bluetooth ® word mark and logos are owned by Bluetooth SIG, Inc. Note: Software screens included in this document are in English only and are included for reference only. They may be different from the screen that displays on your terminal. i Chapter 1 - Getting Started Introduction........................................................................... 1-1 Unpacking the QC890 Verifier............................................. 1-1 QC890 Verifier Features....................................................... 1-1 Using the QC890 Verifier..................................................... 1-2 Scan Button........................................................................... 1-2 Scan Button LEDs.......................................................... 1-2 User LED Indications..................................................... 1-3 Physical Connections............................................................ 1-3 Specifications........................................................................ 1-4 Internal Battery ..................................................................... 1-4 Charging the Battery ...................................................... 1-4 Powering On the QC890 Verifier .................................. 1-4 Chapter 2 - Quick Check ImageData Quick Check ImageData....................................................... 2-1 Installation of Quick Check ImageData ............................... 2-1 Communication Interfaces.................................................... 2-1 USB Communication Interface ...................................... 2-1 USB COM Port Emulation............................................. 2-2 RS-232 Serial Communication Interface ....................... 2-3 RS-232 Selections .......................................................... 2-3 Bluetooth............................................................................... 2-3 Using the QC890 Verifier with Bluetooth Devices ....... 2-4 Enabling Your Device for Bluetooth .................................... 2-5 Enabling QCID for Bluetooth............................................... 2-7 Using Quick Check ImageData ............................................ 2-8 Help System.......................................................................... 2-9 Chapter 3 - Using the Quick Check 890 Verifier System Scanning a Bar Code Symbol Using the QC890 Verifier .... 3-1 Scanning a Bar Code Symbol Using Quick Check ImageData .................................................... 3-1 Table of Contents ii Calibrating the QC890 Verifier ............................................ 3-2 Scanning Properly Using a Pen/Mouse Wand...................... 3-3 Calibrating an External Pen/Mouse Wand ........................... 3-4 Scanning Properly Using the QC3800V Linear Imager: ...... 3-5 Calibration Log ..................................................................... 3-6 Reflectometer Mode ............................................................. 3-7 Chapter 4 - Maintenance Cleaning the External Devices.............................................. 4-1 QC890 Verifier ..................................................................... 4-1 Recertification....................................................................... 4-1 Chapter 5 - Customer Support Product Service and Repair .................................................. 5-1 Online Product Service and Repair Assistance .............. 5-2 Technical Assistance ............................................................ 5-2 Online Technical Assistance .......................................... 5-3 Limited Warranty.................................................................. 5-3 Chapter A - Apertures Pen/Mouse Wand Aperture Selection...................................A-1 Chapter B - Menu Setting Bar Codes Resetting the Standard Product Defaults ..............................B-1 Illumination Timer................................................................B-1 Power Down Timer...............................................................B-1 Chapter C - Symbology Defaults - Operation Quick Check® 890 User’s Guide1 - 1 1 Getting Started Introduction The Quick Check® 890 Verifier System (QC890) is a professional quality control system for verifying the readability and standards compliance of printed linear bar code symbols. This verification system implements an integrated approach that consists of the QC890 Verifier unit and the Quick Check® ImageData (QCID) software. The QC890 system offers ease of use, stability and repeatability, flexibility, increased user features and control, and quality testing of the most common industry applications and sym…

Text truncated - open the document above for the full version.

Corporate Headquarters +1 800-782-4263 (North America Only) Hand Held Products, Inc. 700 Visions Drive P.O. Box 208 Skaneateles Falls, NY 13153-0208 USA QC890 & QC900 Difference Statement January 11, 2007 To Whom It May Concern: The QC890 is a standard product for general sales and usage. The QC900 was a customer requested model number identifier for the same unit. The specific difference is with the model number on the label printout. It is a customer special part number, there are no software, electrical or hardware differences. Any questions or problems feel free to contact me. Regards, Michael Robinson Compliance Manager-Imaging Systems [email protected] 315-554-6387

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 October 25, 2006 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, Hand Held Products, Inc. requests confidentiality for the following products: FCC ID Number Product Title/Model HD5QC900A QC890 Quick Check™ Verifier product For the product stated above, we request that the following information be held confidential: 1) Electrical Schematics of the Circuitry and Block Diagram 2) Operational Description 3) Block Diagrams 4) Test Setup Codes and Instructions 5) Parts Lists / Bills of Materials / Part Drawings / Label Drawings and Artworks No other items submitted as part of the equipment authorization filing process are deemed confidential. The above exhibits contain Hand Held Products, Inc. trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Michael Robinson Compliance Manager Imaging Systems Hand Held Products, Inc. Desk Phone: 315-685-2954 Page 2 [email protected]

100001912 A 500006377 RELEASE LABEL, VERIFIER AGENCY 500006377 B FOUR 06/22/05 D.FLETCHER05/26/05 Notes : 2. REFERENCE PRO-E DRAWING 500006382 3. WINDOW TO REMAIN UNPRINTED 500000004760 THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY AND CONFIDENTIALTHESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY AND CONFIDENTIAL MATERIAL OF HAND HELD PRODUCTS, INC. AND SHALL NOT BEMATERIAL OF HAND HELD PRODUCTS, INC. AND SHALL NOT BE REPRODUCED, OR COPIED, OR USED AS A BASIS FOR MANUFACTURE OR SALEREPRODUCED, OR COPIED, OR USED AS A BASIS FOR MANUFACTURE OR SALE OF EQUIPMENT OR DEVICES WITHOUT WRITTEN PERMISSION. c OF EQUIPMENT OR DEVICES WITHOUT WRITTEN PERMISSION. c REV#REV#REV DESCRIPTIONREV DESCRIPTION DESIGNED BY DESIGNED BY DATEDATE ARTWORK LEVEL ARTWORK LEVEL TITLE: TITLE: AA DRAWING NO: DRAWING NO: REVREV SCALESCALE DO NOT SCALEDO NOT SCALE SHEET SHEET 11 OF OF 11 DRAWING NO. DRAWING NO. DATE DATE ECN#ECN# X ½ X ½ X ½ X ½ X 4. BLUETOOTH SYMBOL SHOULD CONTAIN A KEEP OUT AREA DEFINED AS A BOX ON EACH SIDE OF THE SYMBOL ½ THE HEIGHT OF THE SYMBOL. THE BOX IS NOT PRINTED. 1. COLORS: PANTONE PROCESS BLACK: BLUETOOTH SYMBOL PANTONE PROCESS WHITE: ALL OTHER GRAPHICS BACKGROUND: HHP BLUE GREY N10410 www.handheld.com Hand Held Products, Inc. Skaneateles Falls, NY 13153 USA Tested to Comply With FCC Standards FOR HOME OR OFFICE USE Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003. 0682 FCC ID: HD5QC900A IC: 1693B-QC900A . . r f e t g e p u r f e t g e p u t S c h h e r e i i t S c h h e r e i i . . TU V i l Rh e n and o Pr du ct S afe ty TU V i l Rh e n and o Pr du ct S afe ty S/N ITEM SW REV No user serviceable parts. Assembled in USA. Opening Voids Warranty. E 5 3 7 4 0 1 7 D 2 1 See Pkg For Patent Listing CORDED INPUT: 5V 1.8A B VOLTAGE, IC ID 11/20/0650000000XXXX PRELIMINARY B

PAGE 1 OF 8 EUT Internal Photos FOR: Quickcheck Verifier (Bar Code Scanner) with BT MODEL #: QC900 and QC890 Hand Held Products, Inc. 700 Vision Drive Skaneateles Falls, NY 13153 U.S.A FCC ID: HD5QC900A IC ID: 1693B-QC900A TEST REPORT #: HANDH_003_05002_EUT_INT_PHOTOS DATE: 2007-1-11 Bluetooth Qualification Test Facility (BQTF) FCC listed# 101450 IC recognized # 3925 CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May © Copyright by CETECOM PAGE 2 OF 8 Table of Contents .................................................................................................................................... 3 1ASSESSMENT ............................................................................................................... 4 2EUT INTERNAL PHOTOS 2.1 ......................................... 4 MAIN CIRCUIT BOARD SHOWING THE RADIO MODULE AND ANTENNA. 2.2 ...................................................................................................... 5 EUT OPEN FROM THE BOTTOM 2.3 ....................................................................................... 6 BLUETOOTH MODULE WITH SHIELDING 2.4 ................................................................................ 7 BLUETOOTH MODULE WITHOUT SHIELDING 2.5 ........................................................ 8 BLUETOOTH MODULE WITHOUT SHIELDING BOTTOM SIDE This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. PAGE 3 OF 8 1 Assessment The following is in compliance with the applicable criteria specified in FCC rules Parts 2, 22 and 24 of Title 47 of the Code of Federal Regulations and in compliance with the applicable criteria specified in Industry Canada rules RSS132 and RSS133. Company Description Model # Quickcheck Verifier with BT QC890 and QC900 Hand Held Products, Inc. Date: 2007-1-11 Name: Peter Mu Title: Project Engineer Company: Cetecom Inc. Address: 411 Dixon Landing Rd, Milpitas, CA 95035, USA Phone: +1 408 586 6221 Email: [email protected] This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. PAGE 4 OF 8 2 EUT INTERNAL PHOTOS 2.1 Main circuit board showing the radio module and antenna. This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. PAGE 5 OF 8 2.2 EUT open from the bottom This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. PAGE 6 OF 8 2.3 Bluetooth Module with Shielding This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. PAGE 7 OF 8 2.4 Bluetooth Module Without Shielding This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. PAGE 8 OF 8 2.5 Bluetooth Module Without Shielding Bottom Side This report shall not be reproduced except in full without the written approval of: CETECOM, Inc.

Bluetooth Qualification Test Facility (BQTF) FCC listed# 101450 IC recognized # 3925 CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May © Copyright by CETECOM FCC Test Report FCC Part 15.247 for FHSS systems/ CANADA RSS-210 FOR: Quickcheck Verifier (Bar Code Scanner) with BT MODEL #: QC900 and QC890 Hand Held Products, Inc. 700 Vision Drive Skaneateles Falls, NY 13153 U.S.A FCC ID: HD5QC900A IC ID: 1693B-QC900A TEST REPORT #: HANDH_003_05002_15.247BT DATE: 2007-1-11 Test Report #: HANDH_003_05002_15.247BT Date of Report : 2007-1-11 Page 2 of 54 TABLE OF CONTENTS 1 Assessment_____________________________________________________________________4 Technical responsibility for area of testing: ______________________________________________4 EMC & Radio __________________________________________________________________________________4 2 Administrative Data _____________________________________________________________5 2.1 Identification of the Testing Laboratory Issuing the EMC Test Report _____________________5 2.2 Identification of the Client __________________________________________________________5 2.3 Identification of the Manufacturer ___________________________________________________5 3 Equipment under Test (EUT) ______________________________________________________6 3.1 Specification of the Equipment under Test_____________________________________________6 3.2 Identification of the Equipment Under Test (EUT) ______________________________________6 3.3 Identification of Accessory equipment ________________________________________________6 4 Subject Of Investigation __________________________________________________________7 5 Measurements (RADIATED) ______________________________________________________8 5.1 MAXIMUM PEAK OUTPUT POWER § 15.247 (RADIATED) ___________________________8 5.1.1 LIMIT SUB CLAUSE § 15.247 (b) (1) (2) (3) (4)_______________________________________________8 5.1.2 EIRP: _________________________________________________________________________________8 5.2 RESTRICTED BAND EDGE COMPLIANCE RADIATED §15.247/15.205 ________________12 5.2.1 LIMITS _______________________________________________________________________________12 5.2.2 RESULTS (2402MHz) ___________________________________________________________________13 5.2.3 RESULTS (2480MHz) ___________________________________________________________________15 5.3 TRANSMITTER SPURIOUS EMISSIONS RADIATED § 15.247/15.205/15.209 ____________17 5.3.1 LIMITS _______________________________________________________________________________17 5.3.2 RESULTS _____________________________________________________________________________18 5.4 RECEIVER SPURIOUS RADIATION § 15.209/RSS210 ________________________________27 5.4.1 LIMITS _______________________________________________________________________________27 5.4.2 RESULTS _____________________________________________________________________________28 6 Measurements (CONDUCTED) ___________________________________________________32 6.1 MAXIMUM PEAK OUTPUT POWER § 15.247 (CONDUCTED) ________________________32 6.1.1 LIMIT SUB CLAUSE § 15.247 (b) (1) ______________________________________________________32 6.1.2 RESULTS: ____________________________________________________________________________32 6.2 20dB BANDWIDTH ______________________________________________________________36 6.2.1 LIMIT SUB CLAUSE § 15.247 (a) (1) (i) (ii) (iii) _____________________________________________36 6.2.2 RESULTS: ____________________________________________________________________________36 6.2.3 LIMIT SUB CLAUSE § 15.247 (a) (1) (i) (ii) (iii) _____________________________________________40 6.2.4 RESULTS: ____________________________________________________________________________40 6.3 NUMBER OF HOPPING CHANNELS ______________________________________________42 6.3.1 LIMIT SUB CLAUSE § 15.247 (a) (1) (iii)___________________________________________________42 6.3.2 RESULTS: ____________________________________________________________________________42 6.4 TIME OF OCCUPANCY (DWELL TIME)___________________________________________44 Test Report #: HANDH_003_05002_15.247BT Date of Report : 2007-1-11 Page 3 of 54 6.4.1 LIMIT SUB CLAUSE § 15.247 (a) (1) (i) (ii) (iii) _____________________________________________44 6.4.2 RESULTS: ____________________________________________________________________________44 6.5 AC Line Conducted Emission § 15.207 ______________________________________________48 6.5.1 110V Measurement______________________________________________________________________48 6.5.2 220V Measurement______________________________________________________________________50 7 TEST EQUIPMENT AND ANCILLARIES USED FOR TESTS ________________________52 8 BLOCK DIAGRAMS ___________________________________________________________53 Test Report #: HANDH_003_05002_15.247BT Date of Report : 2007-1-11 Page 4 of 54 1 Assessment The following is in compliance with the applicable criteria specified in FCC rules Part 15.247 of the Code of Federal Regulations and in compliance with the applicable criteria specified in Industry Canada rules RSS210. Company Description Model # Hand Held Products, Inc. Quickcheck Verifier with BT QC890 and QC900 Technical responsibility for area of testing: 2006-12-01 EMC & Radio Lothar Schmidt (Test Lab Manager) Date Section Name Signature The test results of this test report relate exclusively to the test item specified in Identification of the Equipment under Test. The CETECOM Inc. USA does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be repr…

Text truncated - open the document above for the full version.

Test Setup Photos FCC Part 15.247 for FHSS systems/ CANADA RSS-210 FOR: Quickcheck Verifier (Bar Code Scanner) with BT MODEL #: QC900 and QC890 Hand Held Products, Inc. 700 Vision Drive Skaneateles Falls, NY 13153 U.S.A FCC ID: HD5QC900A IC ID: 1693BQC900A TEST REPORT #: HANDH_003_05002_15.247BT DATE: 2006-09-01 Bluetooth Qualification Test Facility (BQTF) FCC listed# 101450 IC recognized # 3925 CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May © Copyright by CETECOM Test Report #: HANDH_003_05002_15.247BT Date of Report : 12/01/2006 Page 2 of 8 Table of Contents 1 Assessment.......................................................................................................................................... 3 2 Test Setup Photos............................................................................................................................... 4 2.1 AC Line Conducted Emission................................................................................................................4 2.2 Radiated Spurious Emissions.................................................................................................................6 2.3 Conducted Measurements......................................................................................................................8 Test Report #: HANDH_003_05002_15.247BT Date of Report : 12/01/2006 Page 3 of 8 1 Assessment The following is in compliance with the applicable criteria specified in FCC rules Parts 2 and 15 of Title 47 of the Code of Federal Regulations and in compliance with the applicable criteria specified in Industry Canada rules RSS210. Company Description Model # Hand Held Products Barcode Verifier QC890 and QC900 Date: 1/5/2007 Name: Peter Mu Title: Project Engineer Company: Cetecom Inc. Address: 411 Dixon Landing Rd, Milpitas, CA 95035, USA Phone: +1 408 586 6221 Email: [email protected] Test Report #: HANDH_003_05002_15.247BT Date of Report : 12/01/2006 Page 4 of 8 2 Test Setup Photos 2.1 AC Line Conducted Emission Test Report #: HANDH_003_05002_15.247BT Date of Report : 12/01/2006 Page 5 of 8 Test Report #: HANDH_003_05002_15.247BT Date of Report : 12/01/2006 Page 6 of 8 2.2 Radiated Spurious Emissions Test Report #: HANDH_003_05002_15.247BT Date of Report : 12/01/2006 Page 7 of 8 Test Report #: HANDH_003_05002_15.247BT Date of Report : 12/01/2006 Page 8 of 8 2.3 Conducted Measurements