HEDSSAC300802.11b/g/n Wireless Access Point, 2.4GHz Ceiling/Wall/Desktop Enterprise AP

– 1 – Safety and Regulatory Information 802.11a/ac/b/g/n Wireless Access Points ECW3320, ECW3320-C, ECW3320-L, ECW5320, ECW5320-C, ECW5320-L This document provides information on AP safety, regulatory statements and compliances. It includes these sections: ◆“Compliances and Safety Statements” on page 1 ◆“Warnings and Cautionary Messages” on page 6 Compliances and Safety Statements FCC Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ◆Reorient or relocate the receiving antenna ◆Increase the separation between the equipment and receiver ◆Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ◆Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E082014-CS-R01 150200000883A www.edge-core.com Safety and Regulatory Information – 2 – This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. CE MarkCE Mark Declaration of Conformance for EMI and Safety (EEC) This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Note: Do not use the product outdoors in France. Europe - EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/ 5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: ◆EN 60950-1:2006 + A11: 2009+ A1:2010 + A12: 2011 Safety of Information Technology Equipment. CountryRestrictionReason/Remark BulgariaNoneGeneral authorization required for outdoor use and public service FranceOutdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 italyNoneIf used outside of own premises, general authorization is required LuxembourgNoneGeneral authorization required for network and service supply(not for spectrum) NorwayImplementedThis subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation NoneOnly for indoor applications Safety and Regulatory Information – 3 – ◆EN 300 328 V1.8.1: 2012-06 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive. ◆EN 301 893 V1.7.1 (2012-06) Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive. ◆EN 301 489-1 V1.9.2 (2011-09) EN 301 489-17 V2.2.1 (2012-09) Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment. ◆EN 55022: 2010 + AC: 2011 Limits and methods of measurement of radio disturbance characteristics of information technology equipment. ◆EN 55024: 2010 Information technology equipment immunity characteristics limits and methods of measurement. ◆EN 50385: 2002 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz - 300 GHz). This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Declaration of Con…

Text truncated - open the document above for the full version.

– 1 – Quick Start Guide 802.11a/ac/b/g/n Wireless Access Points ECW3320, ECW3320-C, ECW3320-L, ECW5320, ECW5320-C, ECW5320-L The ECW3320/ECW3320-C/ECW3320-L/ECW5320/ECW5320-C/ECW5320-L AP includes its own built-in features for mounting the unit to a wall or suspended ceiling T-rail. Note: For Safety and Regulatory information, refer to the Safety and Regulatory Information document included with the AP. Caution: The planning and installation of the AP requires professional personnel that are trained in the installation of radio transmitting equipment. The user is responsible for compliance with local regulations concerning items such as antenna power, use of lightning arrestors, grounding, and radio mast or tower construction. Therefore, it is recommended to consult a professional contractor knowledgeable in local radio regulations prior to equipment installation. Follow these steps to install the AP: 1. Unpack the APUnpack the AP and check the package contents. ◆802.11a/ac/b/g/n Wireless Access Point ◆AC power adapter ◆Ceiling-mount accessory ◆Four adhesive foot pads ◆Documentation — Quick Start Guide (this guide) and Regulatory and Safety Information The 802.11a/ac/b/g/n Wireless Access Points include these models: ◆ ECW3320 — 802.11b/g/n 2.4 GHz stand-alone AP ◆ ECW3320-C — 802.11b/g/n 2.4 GHz cloud-based AP ◆ ECW3320-L — 802.11b/g/n 2.4 GHz controller-based AP ◆ ECW5320 — 802.11a/ac/b/g/n dual-band stand-alone AP ◆ ECW5320-C — 802.11a/ac/b/g/n dual-band cloud-based AP ◆ ECW5320-L — 802.11a/ac/b/g/n dual-band controller-based AP E082014-CS-R01 150200000882A www.edge-core.com Quick Start Guide – 2 – 2. Mount the APAfter planning your installation, mount the unit on a wall or suspended ceiling T-rail. .Mounting on a Wall Set two screws in the wall 116 mm (4.57 in.) apart. Slide the AP’s wall mounting slots down onto the screws so that the unit is secure. 2 1 1 2 1 2 3 .Mounting on a Ceiling T-rail Attach the included ceiling-mount accessory to the base of the AP. Position the AP’s ceiling-mount clip holders on either side of the T-rail. Turn the AP until the two clips lock the AP to the T-rail. 1 2 3 Quick Start Guide – 3 – 3. Connect CablesConnect network cable to the WAN/PoE 1000BASE-T RJ-45 port for your network connection. The WAN/PoE port connection can also provide PoE power to the unit. (Optional) Connect a local LAN switch or computers to the LAN1 and LAN2 100BASE-TX RJ-45 ports. 4. Connect PowerIf you do not power the unit using PoE, connect the AC power adapter to the AP and to an AC power source. Connect Category 5e or better cable to the WAN/PoE RJ-45 port. 1 1 Connect the power adapter to the power socket on the AP. Plug the power adapter into a nearby AC power source. 1 2 1 2 Quick Start Guide – 4 – 5. Verify AP OperationVerify basic AP operation by checking the system LEDs. The WAN LED and any connected LAN port LEDs should light up green. The circular LED on the top panel should light up green and blue to indicate 2.4 GHz and 5 GHz radio operation respectively. 6. Connect to the Web User Interface The AP offers a user-friendly web-based management interface for the configuration of all the unit’s features. You can make initial configuration changes by connecting a PC directly to the AP’s LAN port. The AP has a default management IP address of 192.168.2.1 and a subnet mask of 255.255.255.0. You must set your PC IP address to be on the same subnet as the AP (that is, the PC and AP addresses must both start 192.168.2.x). Log in to the web interface using the default settings: ◆Login Name — root ◆Password — admin123 WAN and LAN1/LAN2 Link/Activity LEDs Radio LED — 2.4 GHz (green) and 5 GHz (blue) 1 2 1 2 Quick Start Guide – 5 – For more information on AP configuration using the web interface, refer to the Management Guide, which is on the Edge-Core web site, www.edge-core.com. Quick Start Guide – 6 – Hardware Specifications ItemSpecification Chassis Size (W x D x H)200 x 200 x 36.5 mm (7.87 x 7.87 x 1.44 inch) Weight750 g (1.65 lb) TemperatureOperating: 0 °C to 40 °C (32 °F to 104 °F) Storage: -20 °C to 70 °C (-4 °F to 158 °F) HumidityOperating: 5% to 95% (non-condensing) Network Interfaces PortsWAN/PoE RJ-45 Port: 1000BASE-T, PoE+ PD LAN1 and LAN2 RJ-45 Ports: 100BASE-TX 2.4 GHz RadioIEEE 802.11b/g/n 5 GHz RadioIEEE 802.11a/ac/n Radio Frequencies2412 ~ 2472 MHz 5745 ~ 5825 MHz (China) 5180 ~ 5320 MHz (ETSI) 5500 ~ 5700 MHz (ETSI) Power Supply PoE Input Power48 VDC, 0.6 A AC Power AdapterAC Input: 100 ~ 240 VAC DC Output: 12 VDC, 2 A Power Consumption22.5 W maximum Regulatory Compliances RadioEN 300 328 V1.8.1:2012 EN 301 893 V1.7.1:2012 EN 301 489-1 V1.9.2 (2011-09) EN 301 489-7 V1.3.1:2005 FCC Part 15C 15.247/15.207 (2.4-2.4835GHz, 5.725-5.850GHz) FCC Part 15E 15.407 (5.150GHz-5.250GHz) EmissionsEN 55022 2010+AC:2011 EN 61000-3-2 2006+A1:2009+A2:2009 FCC Class B Part 15 ImmunityEN 55024 : 2010 EN 61000-4-2 : 2009 SafetyUL (CSA 22.2 No. 60950-1 & UL60950-1) CB (IEC/EN60950-1)

Accton Technology Corporation No.1, Creation Rd. III, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. August 29, 2014 Declaration for no non-US channel operation We, Accton Technology Corporation declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: HEDSSAC300 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ------------------------------------------- Mike Peng Accton Technology Corporation Tel.: +886-3-5770270 #1874 Fax: +886-3-578-7550 E-mail: [email protected]

Accton Technology Corporation No.1, Creation Rd. III, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: 2014/8/27 Subject: Request for Confidentiality FCC ID: HEDSSAC300 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 2014/09/30. External Photos Internal Photos Test setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Sincerely yours, ------------------------------------------------------- Mike Peng Accton Technology Corporation Tel.: +886-3-5770270 #1874 Fax: +886-3-578-7550 E-mail: [email protected]

Accton Technology Corporation No.1, Creation Rd. III, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. Power of Attorney Date：2014/8/29 To whom it may concern: We, the undersigned Accton Technology Corporation hereby authorize Bureau Veritas Consumer Product Service (Hong Kong) Limited, Taoyuan Branch of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. This authorization is limited to the following products: FCC ID: HEDSSAC300 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------- Mike Peng Accton Technology Corporation Tel.: +886-3-5770270 #1874 Fax: +886-3-578-7550 E-mail: [email protected]

Accton Technology Corporation No.1, Creation Rd. III, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. Professional Installation Attestation Date: 2014-08-29 FCC ID: HEDSSAC300 To Whom It May Concern: Please be advised that due to the unique Market and function targeted by this product, this product will need special trained professional in configuring and installing the product. We hereby declare that the product will be distributed through controlled distribution channel which has special trained professional to install this product and will not be sold directly to the general public through retail store. Thank you for your attention. Sincerely yours, ------------------------------------------- Mike Peng Accton Technology Corporation Tel.: +886-3-5770270 #1874 Fax: +886-3-578-7550 E-mail: [email protected]

Report No.: RF140718E03A Page 1 Reference No.: 140812E03 CONSTRUCTION PHOTOS OF EUT Report No.: RF140718E03A Page 8 Reference No.: 140812E03 Report No.: RF140718E03A Page 9 Reference No.: 140812E03

(Fig.1) FCC ID: HEDSSAC300 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Back Side: Label Here 246000001201A UL LABEL EAP622730R-H-0714-ACN Carry SEP04'14 Lin SEP04'14 01 59.80 29.80 5.08 5.08 135.00° R0.30 Model : SS-N300-US SS-N300-EU Input Voltage Range : 12V , 2A FCC ID : HEDSSAC300 FCC CLASS B Made in XXX246000001201A R01 XX XX 44 4

Report No.: RF140718E03A Page 2 Reference No.: 140812E03 Report No.: RF140718E03A Page 3 Reference No.: 140812E03 Report No.: RF140718E03A Page 4 Reference No.: 140812E03 Report No.: RF140718E03A Page 5 Reference No.: 140812E03 Report No.: RF140718E03A Page 6 Reference No.: 140812E03 Report No.: RF140718E03A Page 7 Reference No.: 140812E03

Report No.: SA140718E03B 1 of 7 Report Format Version 5.0.1 Reference No.:140812E05 RF EXPOSURE REPORT REPORT NO.: SA140718E03B MODEL NO.: ECW3320, ECW3320-L, ECW3320-C, SS-N300-US FCC ID:HEDSSAC300 RECEIVED:Aug. 11, 2014 TESTED:Aug. 16, 2014 ISSUED:Sep. 11, 2014 APPLICANT: Accton Technology Corporation ADDRESS: No.1, Creation Rd. III, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA140718E03B 2 of 7 Report Format Version 5.0.1 Reference No.:140812E05 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT ............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. ANTENNA GAIN ...................................................................................................... 6 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .......................... 7 Report No.: SA140718E03B 3 of 7 Report Format Version 5.0.1 Reference No.:140812E05 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140718E03B Original release Sep. 11, 2014 Report No.: SA140718E03B 5 of 7 Report Format Version 5.0.1 Reference No.:140812E05 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA140718E03B 6 of 7 Report Format Version 5.0.1 Reference No.:140812E05 5. ANTENNA GAIN The antennas provided to the EUT, please refer to the following table: Transmitter Circuit Antenna Gain(dBi) <including cable loss> Frequency range (MHz ~ MHz) Antenna TypeConnecter Type Cable Length (mm) Chain (0) 3.16 2400~2500 PCB DipoleIPEX 255 (Gray) Chain (1) 4.04 150 (Blue) Report No.: SA140718E03B 7 of 7 Report Format Version 5.0.1 Reference No.:140812E05 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For WLAN: 15.247(2.4GHz) 802.11b FREQUENCY (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412 - 2462 416.869 4.04 20 0.21025 1.00 NOTE: Directional gain = 10 log[(10 G1/20 + 10 G2/20 ) 2 / 2] = 8.20dBi. 802.11g FREQUENCY (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412 - 2462 519.996 4.04 20 0.26226 1.00 NOTE: Directional gain = 10 log[(10 G1/20 + 10 G2/20 ) 2 / 2] = 8.20dBi. 802.11n (HT20) FREQUENCY BAND (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412 - 2462 982.948 4.04 20 0.49575 1.00 NOTE: Directional gain = 10 log[(10 G1/20 + 10 G2/20 ) 2 / 2] = 8.20dBi. 802.11n (HT40) FREQUENCY BAND (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2422 - 2452 363.576 4.04 20 0.18337 1.00 NOTE: Directional gain = 10 log[(10 G1/20 + 10 G2/20 ) 2 / 2] = 8.20dBi. -- END ---

Report No.: RF140718E03A 1 of 63 Report Format Version 5.2.1 Reference No.: 140812E03 FCC TEST REPORT REPORT NO.: RF140718E03A MODEL NO.: ECW3320, ECW3320-L, ECW3320-C, SS-N300-US FCC ID: HEDSSAC300 RECEIVED: Aug. 11, 2014 TESTED: Aug. 11 to 19, 2014 ISSUED: Sep. 11, 2014 APPLICANT: Accton Technology Corporation ADDRESS: No.1, Creation Rd. III, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF140718E03A 2 of 63 Report Format Version 5.2.1 Reference No.: 140812E03 Table of Contents RELEASE CONTROL RECORD .......................................................................................... 4 1. CERTIFICATION ...................................................................................................... 5 2. SUMMARY OF TEST RESULTS .............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 7 3. GENERAL INFORMATION ....................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ......................................................................... 8 3.2 DESCRIPTION OF TEST MODES ......................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 14 3.4 DUTY CYCLE OF TEST SIGNAL ........................................................................... 15 3.5 DESCRIPTION OF SUPPORT UNITS ................................................................... 16 3.6 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 17 4. TEST TYPES AND RESULTS ................................................................................ 19 4.1 CONDUCTED EMISSION MEASUREMENT ......................................................... 19 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 19 4.1.2 TEST INSTRUMENTS ........................................................................................... 19 4.1.3 TEST PROCEDURES ............................................................................................ 20 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 20 4.1.5 TEST SETUP ......................................................................................................... 20 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 21 4.1.7 TEST RESULTS (MODE 1) .................................................................................... 22 4.1.8 TEST RESULTS (MODE 2) .................................................................................... 24 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 26 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 26 4.2.2 TEST INSTRUMENTS ........................................................................................... 27 4.2.3 TEST PROCEDURES ............................................................................................ 29 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 29 4.2.5 TEST SETUP ......................................................................................................... 30 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 30 4.2.7 TEST RESULTS ..................................................................................................... 31 4.3 6dB BANDWIDTH MEASUREMENT ..................................................................... 44 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................... 44 4.3.2 TEST INSTRUMENTS ........................................................................................... 44 4.3.3 TEST PROCEDURE ...................................................................…

Text truncated - open the document above for the full version.

Report No.: 140407E07 1 of 4 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (MODE 1) Report No.: 140407E07 2 of 4 CONDUCTED EMISSION TEST (MODE 2) Report No.: 140407E07 3 of 4 RADIATED EMISSION TEST (Below 1GHz) Report No.: 140407E07 4 of 4 RADIATED EMISSION TEST (Above 1GHz)