HSW-Z2430HPAMODULAR 2.4 GHZ TRANSCEIVER

Murata Electronics North America

Click to zoom

Application Details

Equipment Class: DTS - Digital Transmission System
Date of Grant: Apr 02, 2008
Application Purpose: Original Equipment
Date of Application: Apr 02, 2008
Equipment Note: MODULAR 2.4 GHZ TRANSCEIVER
Frequency Range: 2405.00000000 - 2475.00000000
Company: Murata Electronics North America
Country: United States

Documents & Files

Select a file to view

Document Text

Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.

Users Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: HSW-Z2430HPA IC: 4492A-Z2430HPA FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 08-0058 Manufacturer: Cirronet, Inc. Model: ZMN2430HPA Manual ZMN2405/ZMN2405HP/ ZMN2430/ZMN2430HP ZMN2430A/ZMN2430HPA Module Series ZigBee ® Module Developer’s Kit User’s Manual 3079 Premiere Pkwy Ste 140 Duluth, Georgia 30097 www.RFM.com +1 (678) 684-2000 Important Regulatory Information RFM Zigbee Series Regulatory Identification ZigBee Module FCC ID IC ID Type of Grant ZMN2405 HSW-ZMN2400 4492A-ZMN2400 Mobile ZMN2405HP HSW-Z2400HP 4492A-Z2400 Mobile ZMN2430 HSW-Z2430 4492A-Z2430 Mobile ZMN2430HP HSW-Z2430HP 4492A-Z2430HP Mobile ZMN2430A HSW-Z2430A 4492A-Z2430A Portable ZMN2430HPA HSW-Z2430HPA 4492A-Z2430HPA Portable THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC User Information NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.” Warning: Changes or modifications to this device not expressly approved by RFM Inc. could void the user’s authority to operate the equipment. These devices can not be co-located with another transmitter without re-evaluation and separate FCC authorization. RF Exposure For ZigBee products with “Mobile Grants”. In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed such that a minimum separation distance of 20 cm shall be maintained from the user and/or general population. Only antennas approved by the FCC for these modules may be used. Contact RFM for details. For ZigBee products with “Portable Grants”. In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element of there devices can be installed such that a separation distance of 2.5 cm or less can be maintained from the user and/or general population. (See Appendix 1 at the end of this document) These products have an intergraded antenna on the module which must not be removed. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée. Suggested End Product Labeling The final end product must be labeled in a visible area on the exterior of the enclosure with the following or similar text: “Contains TX FCC ID: (use correct ID from table above)” European Union All ZigBee modules conform to the requirements of ETSI EN 300 328 standard for radiated emissions. Table of Contents Regulatory Information ................................................................................................ 1. Introduction ............................................................................................................................2 2. ZigBee Networking .................................................................................................................3 2.1 Forming a Network .................................................................................................................4 2.2 Sleeping End Devices ............................................................................................................5 2.3 ZigBee Addressing .................................................................................................................5 2.4 Discovery ...............................................................................................................................6 2.5 Network Topology and Size ...................................................................................................6 2.6 Static Network Addresses and Link Announcements ............................................................8 3. Getting Started .....................................................................................................................10 3.1 Installing ZBDemo ................................................................................................................10 3.2 Installing USB Drivers ..........................................................................................................10 3.3 Running ZBDemo.....…

Text truncated - open the document above for the full version.

Cover Letter(s)

Date: 03-12-08 Federal Communications Commission P.O. Box 429 Columbia, MD 21045 Gentlemen: I hereby appoint Kirby Munroe at Advanced Compliance Solutions, Inc. to act as our agent in the preparation of an application for equipment authorization of model ZMN2430HPA to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC: ID HSW-Z2430HPA listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, Mark Tucker, March 12, 2008 V.P. of Engeneering Cirronet Inc. 3079 Premiere Parkway, Suite 140 Duluth, GA 30097 USA Tel: 678 684 2000 Fax: 678 684 2001

Cover Letter(s)

CONFIDENTIALITY REQUEST Federal Communications Commission Date: Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Cirronet respectfully requests confidentiality of certain materials provided with the submission of the ZMN2430HPA under FCC ID: HSW-Z2430HPA in accordance with FCC Regulations 0.459. The confidentiality request applies to the block diagrams, schematics, and bill of material contained in this filing and included in the following files. 08-0058 – Schematics.pdf 08-0058 – System Block Diagram.pdf 08-0058 – Parts List.pdf 08-0058 – Theory of Operation.pdf The ZMN2430HPA has been developed at considerable effort and expense by Cirronet. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, March 12, 2008 V.P. of Engineering Cirronet Inc. 3079 Premiere Parkway, Suite 140 Duluth, GA 30097 USA Tel: 678 684 2000 Fax: 678 684 2001

Cover Letter(s)

Page 1 of 1 © Cirronet 2003 Cirronet, Inc. Tel: 678 684 2000 3079 Premiere Parkway Fax: 678 684 2001 Duluth, Georgia 30097 USA Date: 3/11/2008 Reference: FCC DA 00-1407 PART 15 UNLICENSED MODULAR TRANSMITTER APPROVAL Cirronet ZMN2430HPA ZigBee Module FCC ID: Z2430HPA Per FCC DA 00-1407, Cirronet’s ZigBee modules are compliance with the requirements listed below. 1. The modular transmitter must have its own RF shielding. Cirroent’s ZigBee Module has shielding as required. 2. The modular transmitter must have buffered modulation/data inputs. Cirroent’s ZigBee Module has buffered modulation and data inputs. 3. The modular transmitter must have its own power supply regulation. Cirronet’s ZigBee Module has its own internal regulator. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). Cirronet’s ZigBee Module output is through a set of connections which are a ball grid array and once soldered to a PC board the connects are not accessible. Without a support PC board the module is unusable. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. Cirronet’s ZigBee Module was tested on a support PC board designed to meet the requirements of modular approval. Complete and open. 6. The modular transmitter must be labeled with its own FCC ID number Cirronet’s ZigBee Module is design as an OEM module. The ZigBee Module will be labeled and instructions given to the OEM customer for FCC label requirements. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter. An Integration Guide is provided with FCC compliance information. 8. The modular transmitter must comply with any applicable RF exposure requirements. An Integration Guide is also provides FCC MPE warnings per antenna types that are used. Al Patrick Sr. Compliance Engineer Cirronet Inc. 3079 Premiere Parkway, Suite 140 Duluth, GA 30097 USA TEL: 678 684 2000 FAX: 678 684 2001

External Photos

ID Label/Location Info

Internal Photos

RF Exposure Info

Test Report

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Test Report Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-Z2430HPA IC: 4492A-Z2430HPA FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 08-0058 Manufacturer: Cirronet, Inc. Model: ZMN2430HPA Test Begin Date: March 7, 2008 Test End Date: March 12, 2008 Report Issue Date: March 27, 2008 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report is not be used to claim certification, approval, or endorsement by NVLAP, NIST or any government agency. Prepared by: Reviewed by: J. Kirby Munroe Manager Wireless Certifications ACS, Inc. R. Sam Wismer Engineering Manager ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 19 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Table of Contents 1.0 General 3 1.1 Purpose 3 1.2 Product Description 3 1.2.1 General 3 1.2.2 Intended Use 3 1.3 Test Methodology and Considerations 3 2.0 Test Facilities 3 2.1 Location 3 2.2 Laboratory Accreditations/Recognitions/Certifications 3 2.3 Radiated Emissions Test Site Description 4 2.3.1 Semi-Anechoic Chamber Test Site 4 2.3.2 Open Area Tests Site (OATS) 5 2.4 Conducted Emissions Test Site Description 6 3.0 Applicable Standards and References 6 4.0 List of Test Equipment 7 5.0 Support Equipment 8 6.0 EUT Setup Block Diagram 8 7.0 Summary of Tests 9 7.1 Antenna Requirement 9 7.2 Power Line Conducted Emissions 9 7.2.1 Test Methodology 9 7.2.2 Test Results 9 7.3 Radiated Emissions - Unintentional Radiation 10 7.3.1 Test Methodology 10 7.3.2 Test Results 10 7.4 6 dB Bandwidth 11 7.4.1 Test Methodology 11 7.4.1 Test Results 11 7.5 Peak Output Power 13 7.5.1 Test Methodology 13 7.5.2 Test Results 13 7.6 Band-Edge Compliance and Spurious Emissions 14 7.6.1 Band-Edge Compliance 14 7.6.1.1 Test Methodology 14 7.6.1.2 Test Results 14 7.6.2 Conducted Spurious Emissions 16 7.6.2.1 Test Methodology 16 7.6.2.2 Test Results 16 7.6.3 Radiated Spurious Emissions 16 7.6.3.1 Test Methodology 16 7.6.3.2 Duty Cycle Correction 16 7.6.3.3 Test Results 17 7.6.3.4 Sample Calculation 18 7.7 Power Spectral Density 18 7.7.1 Test Methodology 18 7.7.2 Test Results 18 8.0 CONCLUSION 19 Additional Exhibits Included In Filing Internal Photographs External Photographs Test Setup Photographs Product Labeling RF Exposure – MPE Calculations Installation/Users Guide Theory of Operation BOM (Parts List) System Block Diagram Schematics Model: ZMN2430HPA FCC ID: HSW-Z2430HPA IC: 4492A-Z2430HPA ACS Report: 08-0058 Advanced Compliance Solutions Page 3 1.0 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-210. 1.2 Product Description 1.2.1 General The ZMN2430HPA is a high-power stand alone Zigbee transceiver module. The ZMN2430HPA 2.4 GHz transceiver module is a low cost, high-power solution for point-to-point, point-to- multipoint and MESH wireless systems. Manufacturer Information: Cirronet, Inc. 3079 Premiere Parkway, Suite 140 Duluth, GA 30097 Test Sample Condition: The test sample was provided in good working order with no visible defects. Detailed photographs of the EUT are filed separately with this filing. 1.2.2 Intended Use The application of the ZMN2430 Series is in a wireless network for data collection in industrial monitoring and control. 1.3 Test Methodology and Considerations The ZMN2430HPA was tested stand alone but did utilize a support PCB for power and programming functionality. 2.0 TEST FACILITIES 2.1 Location The radiated and conducted emissions test sites are located at the following address: Advanced Compliance Solutions 5015 B.U. Bowman Drive Buford, GA 30518 Phone: (770) 831-8048 Fax: (770) 831-8598 2.2 Laboratory Accreditations/Recognitions/Certifications The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions Site have been fully described, submitted to, and accepted by the FCC, Industry Canada and the Japanese Voluntary Control Council for Interference by information technology equipment. In addition, ACS is compliant to ISO 17025 as certified by the National Institute of Standards and Technology under their National Voluntary Laboratory Accreditation Program. The following certification numbers have been issued in recognition of these accreditations and certifications: FCC Registration Number: 894540 Industry Canada Lab Code: IC 4175 VCCI Member Number: 1831 VCCI OATS Registration Number R-1526 VCCI Conducted Emissions Site Registration Number: C-1608 NVLAP Lab Code: 200612-0 Model: ZMN2430HPA FCC ID: HSW-Z2430HPA IC: 4492A-Z2430HPA ACS Report: 08-0058 Advanced Compliance Solutions Page 4 2.3 Radiated Emissions Test Site Description 2.3.1 Semi-Anechoic Chamber Test Site The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is 101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel panels and installed directly on the inner walls of the chamber. The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is bound to the ground plane using 3/4" stainless steel braided cable. The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely operated from inside the control room located 25’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn t…

Text truncated - open the document above for the full version.

Test Setup Photos

Contact Information

Applicant

Mark Tucker(Director of Hardware Engineering)

[email protected]678 684-2009Fax: 678 684-2001

Test Firm

Advanced Compliance Solutions, Inc.Douglas Massey

[email protected]770-831-8048Fax: 770-831-8598

Technical Specifications

#	Rule Parts	Frequency Range	Power Output
1	15C	2.40 GHz - 2.48 GHz	135.00 mW

Modular Type

Limited Single Modular Approval

Confidentiality

Long Term

Grant Notes

Modular approval. Power listed is conducted. This device must transmit with a source-based time-averaging duty factor not exceeding 8.4%.Approval is limited to OEM installation only. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operation conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end-user has no manual instructions to remove or install the device.