HSW-ZMN2400HPZIGBEE MODULE

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15 Subpart C Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-ZMN2400HP FCC Rule Part: 15.247 ACS Report Number: 05-0453-15C Manufacturer: Cirronet, Inc. Model: ZMN2400HP User Guide CIRRONET, INC. © "ZMN2400 Design Documentation ", AP, 2/3/06. 1 of 5 ZMN2400 Radio Module High Power Low Power Manual Preliminary Cirronet, Inc. CIRRONET, INC. © "ZMN2400 Design Documentation ", AP, 2/3/06. 2 of 5 Important Regulatory Information Cirronet Zigbee High Power - FCC ID: HSW-ZMN2400HP IC: 4492A-ZMN2400H Cirronet Zigbee Low Power - FCC ID: HSW-ZMN2400 IC: 4492A-ZMN2400 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC User Information “NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.” Warning: Changes or modifications to this device not expressly approved by Cirronet Inc. could void the user’s authority to operate the equipment. RF Exposure In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed such that a minimum separation distance of 20cm shall be maintained from the user and/or general population. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée. CIRRONET, INC. © "ZMN2400 Design Documentation ", AP, 2/3/06. 3 of 5 Hardware Specifications Radio Specifications Operating Band 2400-2475 MHz Radio Type Direct Sequence (DTS), IEEE 802.15.4 PHY layer Channel Bit Rate 250 Kbps Channel Chipping Rate 2 Mcps Modulation MSK with Raised Cosine Filtering Certification Type DTS device per FCC 15.247 and ETS 300-328 RF power +18 dBm typical, +15 dBm minimum Receiver Sensitivity -98 dBm typical, -95 dBm minimum Link Margin 110 dB (approximately 3 Km Line of Sight propagation) Adjacent Ch. Rejection >39 dB with jammer @ 5 MHz offset Spurious Output Per FCC 15.247 and ETS 300-328 General Input Voltage 5.5 volts minimum, 6 volts nominal, 15 volts maximum Current Consumption 70 mA typical operating, 180 mA peak (transmit) Operating Temp Range -40 C to + 70 C Humidity 95% Non-condensing RF Connector Reverse SMA Host Connector Male DB-9 (Amp 747840-3) Power Connector CUI Stack PJ-002A Theory of Operation The Cirronet ZMN2400 Series radio modules utilizes the IEEE 802.15.4 standard ZigBee Physical layer hardware for wireless low data rate monitoring and control applications. The application of the ZMN2400 Series in a wireless network for data collection in industrial monitoring and control. Block Diagram in Figure 1 The ZMN2400 Series radio modules consist of an RF transceiver and a microprocessor. The RF transceiver receives data and commands from the microprocessor as well as the clock required by the RF transceiver. The Block diagrams in Figure 1 shows both the ZMN2400 (Low Power) and the ZMN2400HP (High Power). They are the same with the exception of T/R switches and a PA (Power Amp) and a LNA (Low Noise Amp) in the high power version. The output power is +16 dBm for the high power and 0 dBm for the low power ZigBee Transceivers. CIRRONET, INC. © "ZMN2400 Design Documentation ", AP, 2/3/06. 4 of 5 ZigBee RF Transceiver Processor S P D T S P D T Data Bus LPF PA LNA BPF ZigBee ZMN2400HP High Power Module Figure 1 CIRRONET, INC. © "ZMN2400 Design Documentation ", AP, 2/3/06. 5 of 5 ZMN2400 Frequency Selection The ZMN2400 is not frequency agile during run-time, but it can select an unoccupied portion of the spectrum at startup. The ZMN-2400 series uses a set of channels as defined by the IEEE 802.15.4 / ZigBee standards which span a range from 2405 to 2480 MHz with 5 MHz spacing between channels: Center Frequency (MHz) Nominal Occupied BW ZigBee Channel Designator 2405 2402.5-2407.5 11 2410 2407.5-2412.5 12 2415 2412.5-2417.5 13 2420 2417.5-2422.5 14 2425 (default) 2422.5-2427.5 15 2430 2427.5-2432.5 16 2435 2432.5-2437.5 17 2440 2437.5-2442.5 18 2445 2442.5-24…

Text truncated - open the document above for the full version.

Date: 2-2-06 Gentlemen: Cirronet respectfully requests the following antenne for use with the ZigBee Modules approvals. Manufacture Antenna Type Model Number Antenna Gain Connector Type Mobile Mark Omni OD9- 2400 9 dBi Type N Sincerely, Al Patrick Al Patrick Sr. Compliance Engineer Cirronet Inc. 5375 Oakbrook Parkway Norcross, GA 30093 USA TEL: 678 684 2000 FAX: 678 684 2001 www.cirronet.com [email protected]

CONFIDENTIALITY REQUEST Federal Communications Commission Date: 1-19-06 Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Cirronet respectfully requests confidentiality of certain materials provided with the submission of the ZigBee Module under FCC ID: HSW-ZMN2400HP in accordance with FCC Regulations 0.459. The confidentiality request applies to the (1) schematic diagrams, (2) detailed block diagrams, (3) detailed operational descriptions, and (4) parts lists, that may be contained in this filing. The ZigBee Module has been developed at considerable effort and expense by Cirronet. These items are considered as Trade Secrets and therefore public access to the proprietary material could possible result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, Al Patrick Al Patrick Sr. Compliance Engineer Cirronet Inc. 5375 Oakbrook Parkway Norcross, GA 30093 USA TEL: 678 684 2000 FAX: 678 684 2001 www.cirronet.com [email protected]

Page 1 of 2 © Cirronet 2003 Cirronet, Inc. Tel: 678 684 2000 3079 Premiere Parkway Fax: 678 684 2001 Duluth, Georgia 30097 USA Date: 1-19-06 Reference: FCC DA 00-1407 PART 15 UNLICENSED MODULAR TRANSMITTER APPROVAL Cirronet ZMN2400HP Module Per FCC DA 00-1407, Cirronet’s ZigBee modules are compliance with the requirements listed below. 1. The modular transmitter must have its own RF shielding. Cirroent’s ZigBee Module has shielding as required. 2. The modular transmitter must have buffered modulation/data inputs. Cirroent’s ZigBee Module has buffered modulation and data inputs. 3. The modular transmitter must have its own power supply regulation. Cirronet’s ZigBee Module has its own internal regulator. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). Cirronet’s ZigBee Module output is through a set of connections which are like a ball grid array and once soldered to a PC board the connects are not accessible. Without a support PC board the module is unusable. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. Cirronet’s ZigBee Module was tested on a support PC board designed to meet the requirements of modular approval. Complete open. 6. The modular transmitter must be labeled with its own FCC ID number Cirronet’s ZigBee Module is design as a OEM module. The ZigBee Module will be labeled and instructions given to the OEM customer for Page 2 of 2 © Cirronet 2003 FCC label requirements. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter. An Integration Guide is provided with FCC compliance information. 8. The modular transmitter must comply with any applicable RF exposure requirements. An Integration Guide is also provides FCC MPE warnings per antenna types that are used. Al Patrick Sr. Compliance Engineer Cirronet Inc. 3079 Premiere Parkway, Suite 140 Duluth, GA 30097 USA TEL: 678 684 2000 FAX: 678 684 2001 www.cirronet.com [email protected]

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15 Subpart C Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-ZMN2400HP FCC Rule Part: 15.247 ACS Report Number: 05-0453-15C Manufacturer: Cirronet, Inc. Model: ZMN2400HP External Photographs Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Figure 1: External Photographs – Front View with Shields (On evaluation Board) Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Figure 2: External Photographs – Front View without Shields Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Figure 3: External Photographs – Back View

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15 Subpart C Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-ZMN2400HP FCC Rule Part: 15.247 ACS Report Number: 05-0453-15C Manufacturer: Cirronet, Inc. Model: ZMN2400HP Label Information Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Label Information: Figure 1: Label Information – Sample Label Figure 2: Label Information – Label Placement

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15 Subpart C Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-ZMN2400HP FCC Rule Part: 15.247 ACS Report Number: 05-0453-15C Manufacturer: Cirronet, Inc. Model: ZMN2400HP External Photographs Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Figure 1: External Photographs – Front View with Shields (On evaluation Board) Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Figure 2: External Photographs – Front View without Shields Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Figure 3: External Photographs – Back View

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15 Subpart C Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-ZMN2400HP FCC Rule Part: 15.247 ACS Report Number: 05-0453-15C Manufacturer: Cirronet, Inc. Model: ZMN2400HP RF Exposure Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 General Information: Applicant: Cirronet, Inc. ACS Project: 05-0453 FCC ID: HSW-ZMN2400HP Device Category: Mobile Environment: General Population/Uncontrolled Exposure Technical Information: Antenna Type: Omni-directional Antenna Gain: 9dBi Transmitter Conducted Power: 17.03dBm Maximum System EIRP: 26.03dBm Operating Configuration: Mobile (Module) Exposure Conditions: Greater than 20 centimeters MPE Calculation The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG π Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 247517.031.0050.4797.943 200.080 Power Density (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.) Installation Guidelines The installation manual contains the following text advising how to install the equipment to maintain compliance with the FCC RF exposure requirements: “RF Exposure (Intentional Radiators Only) In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed such that a minimum separation distance of 20cm is maintained from the general population.” Conclusion This device complies with the MPE requirements by providing adequate separation between the device, any radiating structure and the general population.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15 Subpart C Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-ZMN2400HP FCC Rule Part: 15.247 ACS Report Number: 05-0453-15C-B Manufacturer: Cirronet, Inc. Model: ZMN2400HP Test Begin Date: January 25, 2005 Test End Date: January 30, 2005 Report Issue Date: February 15, 2006 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612 Prepared by: Reviewed by: J. Kirby Munroe Manager Wireless Certifications ACS, Inc. R. Sam Wismer Engineering Manager ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 17 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Table of Contents 1.0 General 3 1.1 Purpose 3 1.2 Product Description 3 1.2.1 General 3 1.2.2 Manufacturer Information 3 1.2.3 Antenna List 3 2.0 Test Facilities 4 2.1 Location 4 2.2 Laboratory Accreditations/Recognitions/Certifications 4 2.3 Radiated Emissions Test Site Description 5 2.3.1 Semi-Anechoic Chamber Test Site 5 2.3.2 Open Area Tests Site (OATS) 6 2.4 Conducted Emissions Test Site Description 7 3.0 Applicable Standards and References 7 4.0 List of Test Equipment 8 5.0 Support Equipment 8 6.0 EUT Setup Block Diagram 9 7.0 Summary of Tests 10 7.1 Section 15.203 - Antenna Requirement 10 7.2 Section 15.207 - Power Line Conducted Emissions 10 7.2.1 Test Methodology 10 7.2.2 Test Results 10 7.3 Section 15.109 - Radiated Emissions (Unintentional Radiation) 12 7.3.1 Test Methodology 12 7.3.2 Test Results 12 7.4 Section 15.247(a)(2) – 6 dB Bandwidth 13 7.4.1 Test Methodology 13 7.4.1 Test Results 13 7.5 Section 15.247(b) – Peak Output Power 14 7.5.1 Test Methodology 14 7.5.2 Test Results 14 7.6 Section 15.247(c) – Band-Edge Compliance and Spurious Emissions 15 7.6.1 Section 15.247 (c) – Band-Edge Compliance 15 7.6.1.1 Test Methodology 15 7.6.1.2 Test Results 15 7.6.2 Section 15.247(c) – Conducted Spurious Emissions 17 7.6.2.1 Test Methodology 17 7.6.2.2 Test Results 17 7.6.3 Section 15.247(c) – Radiated Spurious Emissions 18 7.6.3.1 Test Methodology 18 7.6.3.2 Duty Cycle Correction 18 7.6.3.3 Test Results 19 7.6.3.4 Sample Calculation 19 7.7 Section 15.247(d) – Power Spectral Density 20 7.7.1 Test Methodology 20 7.7.2 Test Results 20 9.0 CONCLUSION 20 Model: ZMN2400HP FCC ID: HSW-ZMN2400HP ACS Report: 05-0453-15C-B Advanced Compliance Solutions Page 3 1.0 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15, Subpart C of the FCC’s Code of Federal Regulations. 1.2 Product Description 1.2.1 General The Cirronet ZMN2400HP Series radio modules utilizes the IEEE 802.15.4 standard ZigBee Physical layer hardware for wireless low data rate monitoring and control applications. The application of the ZMN2400 Series is a wireless network for data collection in industrial monitoring and control. 1.2.2 Manufacturer Information Cirronet Inc 3079 Premiere Parkway Suite 140 Duluth, GA 30097 1.2.3 Antenna List Manufacture Antenna Type Model Number Antenna Gain Connector Type Mobile Mark Omni OD9-2400 9 dBi Type N Model: ZMN2400HP FCC ID: HSW-ZMN2400HP ACS Report: 05-0453-15C-B Advanced Compliance Solutions Page 4 2.0 TEST FACILITIES 2.1 Location The radiated and conducted emissions test sites are located at the following address: Advanced Compliance Solutions 5015 B.U. Bowman Drive Buford, GA 30518 Phone: (770) 831-8048 Fax: (770) 831-8598 2.2 Laboratory Accreditations/Recognitions/Certifications The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions Site have been fully described, submitted to, and accepted by the FCC, Industry Canada and the Japanese Voluntary Control Council for Interference by information technology equipment. In addition, ACS is compliant to ISO 17025 as certified by the National Institute of Standards and Technology under their National Voluntary Laboratory Accreditation Program. The following certification numbers have been issued in recognition of these accreditations and certifications: FCC Registration Number: 89450 Industry Canada Lab Code: IC 4175 VCCI Member Number: 1831 ƒ VCCI OATS Registration Number R-1526 ƒ VCCI Conducted Emissions Site Registration Number: C-1608 NVLAP Lab Code: 200612 Model: ZMN2400HP FCC ID: HSW-ZMN2400HP ACS Report: 05-0453-15C-B Advanced Compliance Solutions Page 5 2.3 Radiated Emissions Test Site Description 2.3.1 Semi-Anechoic Chamber Test Site The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is 101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel panels and installed directly on the inner walls of the chamber. The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is bound to the ground plane using 3/4" stainless steel braided cable. The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely operated from inside the control room located 25’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary. The pit is equipped with 1 - 4” PVC chases from the turntable to the pit that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. A diagram of the Semi-An…

Text truncated - open the document above for the full version.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15 Subpart C Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: HSW-ZMN2400HP FCC Rule Part: 15.247 ACS Report Number: 05-0453-15C Manufacturer: Cirronet, Inc. Model: ZMN2400HP Test Setup Photographs Model: ZMN2400HP Advanced Compliance Solutions FCC ID: HSW-ZMN2400HP 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Figure 1: Radiated Emissions – 9dBi Omni-directional Antenna