I88G110PCMCIA 802.11g WLAN Card

ZyAIR G-110 802.11g Wireless CardBus Card Quick Installation Guide Version 1.10 March 2004 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 2 FCC Statement The 802.11g Wireless CardBus Card has been tested to the FCC exposure requirements (Specific Absorption Rate) Caution: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 3 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. o Consult the dealer or an experienced radio/TV technician for help. Costomer Support in U.S.A. ZyXEL Communications Inc. 1130 North Miller Street, Anaheim, CA 92806-2001 U.S.A. Tel: +1-714-632-0882 Fax: +1-714-632-0858 Email: [email protected] http://www.us.zyxel.com PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 4 About Your ZyAIR The ZyAIR is an IEEE 802.11g compliant wireless LAN PC card that fits into any CardBus slot. With the ZyAIR, you can enjoy the wireless mobility within the coverage area. The IEEE 802.11g technology provides greater range and offers transmission rate at up to 54 Mbps. 1. Installation Requirements Before installation, make sure you have the following requirements. • Pentium II 300MHz or above • A minimum of 6 MB available hard disk space • A minimum of 32 MB RAM • A CD-ROM drive • A CardBus slot • Windows 98 SE/Me/2000/XP • Windows 98 SE users may need the Windows 98 SE CD 2. ZyAIR Utility and Hardware Installation The installation procedures are similar for all supported Windows versions. Windows XP screen shots are shown unless otherwise specified. PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 5 DO NOT insert the ZyAIR at this point. 1. Insert the support CD into the CD-ROM drive on your computer. The CD auto runs. Otherwise, locate and double-click on setup.exe. A Welcome screen displays. Click Next. 2. Click Next to accept the default file location or click Browse to select an alternate folder. 3. Windows 98 SE/Me: Click Finish to restart the computer. 4. Locate an available CardBus slot on the computer. 5. With the pin connectors facing the slot and the LED side facing up, slide the ZyAIR into the slot. The LEDs turn on if the ZyAIR is properly inserted. PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 6 Never bend, force or twist the ZyAIR into the slot. 6. Windows 2000: If a warning window displays, click Yes. 7. Windows XP: A Found New Hardware Wizard windows displays. Select Install the software automatically (recommended) and click Next. 8. Windows XP: If a warning window displays, click Continue Anyway. Then click Finish to complete the installation process. After you install the ZyAIR Utility and insert the ZyAIR, an icon appears in the system tray. If the ZyAIR Utility icon displays, the ZyAIR is installed properly. Refer to the ZyAIR Utility User’s Guide to configure the ZyAIR. LED Display LINK ACT PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 7 The following table describes the LEDs on the ZyAIR. LED COLOR STATUS DESCRIPTION Blinking The ZyAIR is receiving or sending data. ACT Blue Off The ZyAIR is not receiving or sending data. On The ZyAIR has a connection to a wireless LAN. Blinking The ZyAIR is connecting to a wireless LAN. LINK Blue Off The ZyAIR is not connected to a wireless LAN or not receiving power. External Antenna Installation For AP 1. Remove the protective cap from the ZyAIR. 2. Connect one end of the antenna converter cable to the external antenna connector on the ZyAIR. 3. Connect the other end of the converter cable to the Reverse-SMA plug of the external antenna. (It is recommended you use ZyXEL’s external antenna series.) 1 2 3 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 8 Troubleshooting PROBLEM CORRECTIVE ACTION Make sure the ZyAIR is inserted into the computer CardBus slot properly and then restart your computer. Check the LEDs on the ZyAIR. Perform a hardware scan by clicking Start, Settings, Control Panel and double-clicking Add/Remove Hardware. (St…

Text truncated - open the document above for the full version.

ZyAIR G-110 802.11g Wireless CardBus Card Quick Installation Guide Version 1.10 March 2004 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 2 FCC Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 3 reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. o Consult the dealer or an experienced radio/TV technician for help. CAUTION: 1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to ensure that the proper spacing is maintained in the event the users places the device in their lap during use (i.e. positioning of antennas must be placed in the upper portion of the PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 4 LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use) and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end- product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a visible area with the following: "Contains TX FCC ID: I88G110". RF Exposure Manual Information That Must be Included The users manual for end users must include the following information in a prominent location "IMPORTANT NOTE: To comply with FCC RF exposure PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 5 compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter." Additional Information That Must be Provided to OEM Integrators The end user should NOT be provided any instructions on how to remove or install the device. Costomer Support in U.S.A. ZyXEL Communications Inc. 1130 North Miller Street, Anaheim, CA 92806-2001 U.S.A. Tel: +1-714-632-0882 Fax: +1-714-632-0858 Email: [email protected] http://www.us.zyxel.com PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com 6 About Your ZyAIR The ZyAIR is an IEEE 802.11g compliant wireless LAN PC card that fits into any CardBus slot. With the ZyAIR, you can enjoy the wireless mobility within the coverage area. The IEEE 802.11g technology provides greater range and offers transmission rate at up to 54 Mbps. 1. Installation Requirements Before installation, make sure you have the following requirements. • Pentium II 300MHz or above • A minimum of 6 MB available hard disk space • A minimum of 32 MB RAM • A CD-ROM drive • A CardBus slot • Windows 98 SE/Me/2000/XP • Windows 98 SE users may need the Windows 98 SE CD 2. ZyAIR Utility and Hardware Installation The installation procedures are similar for all supported Windows versions. Windows XP screen shots are shown unless otherwise specified. PDF created with FinePrint pdfFactory Pro trial version http://www.pdf…

Text truncated - open the document above for the full version.

FCC ID: I88G110 Date: April 14, 2004 Modular Approval Request Letter Dear Sir, There’s a 802.11g Wireless CardBus Card that would like to have your authorization as a modular approval. The specific product as below, 802.11g Wireless CardBus Card, with its designed features and specified description, meets special requirements for full modular approval on FCC Public Notice DA 00-1407 by cross-reference list below. Company : ZyXEL Communications Corporation Model Name : 802.11g Wireless CardBus Card Model Number : ZyAIR G-110 FCC ID : I88G110 Requirement of Public Notice DA00-1407 Reference to ZyAIR G-110 1. The modular transmitter must have its own RF shielding. The module has its own RF shielding. Please see external photo.pdf 2. The modular transmitter must have buffered modulation/data inputs. The modular has buffered data inputs, it is integrated in chip AT24C64. Please see Technical description .pdf 3. The modular transmitter must have its own power supply regulation. All power lines derived from the host device are regulated before energizing other circuits internal to the ZyAIR G-110. Please see operation description .pdf 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The ZyAIR G-110 meets the FCC antenna requirements. It has a built-in, unique antenna. Please see external photo.pdf 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. The ZyAIR G-110 was tested in a stand-alone configuration via a PCMCIA extender. Please see conducted set-up photo.pdf and spurious set-up photo.pdf 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The label position of ZyAIR G-110 is clearly indicated. Please see the label.pdf 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The ZyAIR G-110 is compliant with all applicable FCC rules. Detail instructions are given in the Users Manual. Please see Installation guide.pdf 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). The ZyAIR G-110 comply with applicable RF exposure requirements. Please see RF safety evaluation. pdf Yours sincerely, Elton Chen Assistant Manager Intertek Testing Service Taiwan Ltd. PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com

Photo 1: External photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com Photo 2: External photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com Photo 3: External photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com Photo 4: External photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com

FCC ID Label Location 64.5 mm 40.5 mm PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com

Photo 1: Internal photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com Photo 2: Internal photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com Photo 3: Internal photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com Photo 4: Internal photo ZyAIR G-110 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com

FCC ID. : I88G110 Report No.: EME-040257 Page 1 of 5 Maximum Permissible Exposure (MPE) Evaluation Report Report No.: EME-040257 Model No.: ZyAIR G-110 Issued Date: April 8, 2004 Applicant: ZyXEL Communications Corporation No. 6, Innovation Rd II, Science-Based Industrial Park, Hsin-Chu, Taiwan Test By: Intertek Testing Services Taiwan Ltd. No. 11, Lane 275, Ko-Nan 1 Street, Chia-Tung Li, Shiang-Shan District, Hsinchu City, Taiwan This test report consists of 5 pages in total. It may be duplicated completely for legal use with the allowance of the applicant. It shall not be reproduced except in full, without the written approval of Intertek Laboratory. The test result in this report only applies to the tested sample. Clay Chen Project Engineer Reviewed By Elton Chen PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com FCC ID. : I88G110 Report No.: EME-040257 Page 2 of 5 Table of Contents Summary of Tests.............................................................................................................3 1. Introduction..................................................................................................................4 2. RF Exposure Limit.......................................................................................................4 3. RF Exposure calculations.............................................................................................5 4. Test results....................................................................................................................5 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com FCC ID. : I88G110 Report No.: EME-040257 Page 3 of 5 Summary of Tests MPE Evaluation meet FCC OET No. 65: 1997/ IEEE C95.1-1999 802.11g Wireless CardBus Card-Model: ZyAIR G-110 FCC ID: I88G110 Test Reference Results MPE Evaluation FCC Guidelines for Human Exposure IEEE C95.1 Complies PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com FCC ID. : I88G110 Report No.: EME-040257 Page 4 of 5 1. Introduction The EUT operates in the 2.4GHz ISM band. The EUT (antenna included) is compliant with modular approval and the normal operation distance (after installing in other device, such as router or access point), 20cm from the human body; therefore, the EUT is defined as a Mobile Device. The reason to do the MPE Evaluation is to avoid the RF hazard to human body. The maximum output power and gain of the antenna were used to calculate the limited Power density (S) at 20cm distance away from the product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A) Limits for Occupational / Control Exposures 30-300 61.4 0.163 1.0 6 300-1500 - - F/300 6 1500-100,000 - - 5 6 (B) Limits for General Population / Uncontrolled Exposure 30-300 27.5 0.073 0.2 30 300-1500 - - F/1500 30 1500-100,000 - - 1.0 30 F= Frequency in MHz PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com FCC ID. : I88G110 Report No.: EME-040257 Page 5 of 5 3. RF Exposure calculations From §FCC 1.1310 table 1, the maximum permissible RF exposure for an uncontrolled environment is 1mW/(cm 2 ) Power density (S) is calculated by the following formula: S = (P * G)/4πR 2 where, S = Power density (mW/cm 2 ) P = Output power to antenna (mW) R = Distance between radiating structure and observation point (cm) G = Gain of antenna in numeric π = 3.1416 Example: Assume a mobile device operates at 2412MHz and its maximum output power is 50mW, and the maximum gain of antenna is 1 (numeric) /0dBi. then the power density (S) = (50 * 1)/4*π*20 2 = 0.00995 (mW/cm 2 ) 4. Test results Worst Case Condition: 802.11b (DSSS Modulation) Channel Channel Frequency (MHz) Maximum antenna gain (numeric) Output power to antenna (mW) Power density (mW/cm 2 ) Limit of power density (mW/cm 2 ) 1 2412 1.58 80.35 0.025 1.0 6 2437 1.58 97.05 0.031 1.0 11 2462 1.58 96.83 0.031 1.0 The Notice in Installation Manual has been stated as below: While installing and operating this transmitter, the radio frequency exposure limit of 1mW/(cm*cm) may be exceeded at distances close to the transmitter. therefore, the user must maintain a minimum distance of 20 cm from the device at all time. PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com

FCC ID. : I88G110 Report No.: EME-040258 Page 1 of 62 0597 ILAC MRA Specific Absorption Rate (SAR) Test Report for ZyXEL Communications Corporation on the 802.11g Wireless CardBus Card Model Number: ZyAIR G-110 Test Report: EME-040258 Date of Report: Apr. 6, 2004 Date of test: Mar. 31, 2004 Total No of Pages Contained in this Report: 62 Accredited for testing to FCC Part 15 Tested by: Clay Chen Reviewed by: Elton Chen Review Date: April 7, 2004 All services undertaken are subject to the following general policy: Reports are submitted for exclusive use of the client to whom they are addressed. Their significance is subject to the adequacy and representative character of the samples and to the comprehensiveness of the tests, examinations or surveys made. This report shall not be reproduced except in full, without written consent of Intertek Testing Services, Taiwan Ltd. PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com FCC ID. : I88G110 Report No.: EME-040258 Page 2 of 62 Table of Contents 1.0 Job Description...........................................................................................................4 1.1 Client Information...................................................................................................4 1.2 Equipment under test (EUT)...................................................................................4 1.3 Test plan reference...................................................................................................5 1.4 System test configuration........................................................................................5 1.4.1 System block diagram & Support equipment.......................................................5 1.4.2 Test Position.........................................................................................................6 1.4.3 Test Condition......................................................................................................6 1.5 Modifications required for compliance...................................................................7 1.6 Additions, deviations and exclusions from standards.............................................7 2.0 SAR Evaluation...........................................................................................................8 2.1 SAR Limits..............................................................................................................8 2.2 Configuration Photographs.....................................................................................9 2.3 SAR measurement system.....................................................................................12 2.4 SAR measurement system validation....................................................................13 2.4.1 System Validation result.....................................................................................14 2.4.2 System Performance Check result......................................................................16 2.5 Test Result.............................................................................................................18 3.0 Test Equipment.........................................................................................................19 3.1 Equipment List......................................................................................................19 3.2 Tissue Simulating Liquid......................................................................................20 3.2.1 Body Tissue Simulating Liquid for evaluation test............................................20 3.2.2 Head Tissue Simulating Liquid for System performance Check test.................20 3.2.3 Body Liquid results............................................................................................21 3.2.4 Head Liquid results............................................................................................22 3.3 E-Field Probe and 2450 Balanced Dipole Antenna Calibration............................23 4.0 Measurement Uncertainty.........................................................................................24 5.0 Measurement Traceability.........................................................................................27 6.0 WARNING LABEL INFORMATION - USA.........................................................27 7.0 REFERENCES..........................................................................................................28 8.0 DOCUMENT HISTORY..........................................................................................29 APPENDIX A - SAR Evaluation Data...........................................................................30 APPENDIX B - Photographs..........................................................................................37 APPENDIX C - E-Field Probe and 2450MHz Balanced Dipole Antenna Calibration Data 38 PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com FCC ID. : I88G110 Report No.: EME-040258 Page 3 of 62 STATEMENT OF COMPLIANCE The ZyXEL sample device, model # ZyAIR G-110 was evaluated in accordance with the requirements for compliance testing defined in FCC OET Bulletin 65, Supplement C (Edition 01-01). Testing was performed at the Intertek Testing Services facility in Hsinchu, Taiwan. For the evaluation, the dosimetric assessment system INDEXSAR SARA2 was used. The phantom employed was the box phantom of 2mm thick in one wall. The total uncertainty for the evaluation of the spatial peak SAR values averaged over a cube of 1g tissue mass had been assessed for this system to be ±29.7%. The device was tested at their maximum output power declared by the ZyXEL. In summary, the maximum spatial peak SAR value for the sample device averaged over 1g was found to be: Phantom Position SAR 1g , mW/g 2mm thick box phantom wall EUT perpendicular to the phantom, 0 mm separation. 0.32 mW/g. In conclusion, the tested Sample device was found…

Text truncated - open the document above for the full version.

FCC ID. : I88G110 Report No.: EME-040257 Page 1 of 73 EMC TEST REPORT Report No.: EME-040257 Model No.: ZyAIR G-110 Issued Date: April 8, 2004 Applicant ZyXEL Communications Corporation No. 6, Innovation Rd II, Science-Based Industrial Park, Hsin-Chu, Taiwan Test By: Intertek Testing Services Taiwan Ltd. No. 11, Lane 275, Ko-Nan 1 Street, Chia-Tung Li, Shiang-Shan District, Hsinchu City, Taiwan This test report consists of 73 pages in total. It may be duplicated completely for legal use with the allowance of the applicant. It shall not be reproduced except in full, without the written approval of Intertek Laboratory. The test result in this report only applies to the tested sample. Clay Chen Project Engineer Reviewed By Elton Chen PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com FCC ID. : I88G110 Report No.: EME-040257 Page 2 of 73 Table of Contents Summary of Tests..............................................................................................................3 1. General information......................................................................................................4 1.1 Identification of the EUT........................................................................................4 1.2 Additional information about the EUT....................................................................4 1.3 Antenna description.................................................................................................5 1.4 Peripherals equipment.............................................................................................5 2. Test specifications.........................................................................................................6 2.1 Test standard............................................................................................................6 2.2 Operation mode.......................................................................................................6 2.3 Test equipment........................................................................................................7 3. Minimum 6dB Bandwidth test......................................................................................8 3.1 Operating environment............................................................................................8 3.2 Test setup & procedure............................................................................................8 3.3 Measured data of Minimum 6dB Bandwidth test results........................................8 4. Maximum Output Power test......................................................................................15 4.1 Operating environment..........................................................................................15 4.2 Test setup & procedure...........................................................…

Text truncated - open the document above for the full version.