I88PK5001Z802.11n Wireless ADSL2+ 4-port Gateway

1 PK5001Z 802.11n Wireless ADSL2+ 4-port Gateway Quick Start Guide Version 3.10 2/2012 Edition 2 PK5001Z Quick Start Guide 2 Overview The PK5001Z i s a wireless ADSL router with a four-port built-i n switch. This Quick Start Guide shows you how to use the PK5001Z to connect to the Internet and how to configure the device settings to connect wirelessly y. See your User’s Guide for background information on all features. Quick Login Information LAN IP address http://192.168.0.1 default administrator password Check back label for the info Note: The device is designed to allow both vertical and wall mounted usage. PK5001Z Quick Start Guide 3 Hardware Connections 1 DSL: Use the gray telephone wire to connect your PK5001Z’s DSL port to a telephone jack (or to the modem port on a splitter if you are using one). 2 ETHERNET: Use the yellow Ethernet cable to connect a computer to an ETHERNET port for initial configuration and/or Internet access. 3 POWER: Use the included power adaptor to connect an appropriate power source to the POWER socket. Make sure the power source is on. 4 Push in the POWER button. 5 Look at the lights on the front panel. • The POWER light blinks while your PK5001Z starts up and stays on once it is ready. • Each ETHERNET light stays on if the corresponding ETHERNET port is properly connected and blinks when there is traffic. • The DSL light is on when the PK5001Z has a DSL connection. • The INTERNET light is on when you are able to access the Internet and blinks when the PK5001Z Is sending or receiving data. Wait a couple of minutes while your device checks the connection. If any of these lights are not on, check your connections and inspect your cables for dam age. If the lights are still off, contact your local PK5001Z Quick Start Guide 4 vendor. 2 Internet Connection Setup: Automatic Use this section to have your PK5001Z automatically detect and set up your Internet connection. 1 Open your web browser to a website. Wait while your PK5001Z tries to detect your DSL connection to your ISP. This may take a few minutes. 2 After it detects the connection, the DSL light shows green on your device and the Internet light comes on when the Internet is ready for you to use. If you have a PPPoE connection, you will have to enter your user name and password. 3 Go to section 3 if you wish to configure your wireless settings. 4 If you do not see the connection test screen, or the connection test is not successful , follow the instructions i n the screen below, or check your connections and restart the PK5001Z. If you still cannot access the Internet, follow the steps in section 3. 3 Configuring your Wireless Settings To create a wireless network, the PK5001Z and your wireless computer must all use the sam e SSID (network name), channel and security PK5001Z Quick Start Guide 5 settings. If you do not set wireless security then anyone within range could use your PK5001Z to access your network and the Internet. Choose W PA-PSK wireless security if your wireless device supports it as it is stronger than W EP. Otherwise choose W EP. 1 Select Active and click Next to continue. It i s strongly recommended that Enable OTIST i s NOT selected. See section 7 for more information. 2 C o n f i g u r e your wireless settings i n the screen. Click Next. 3 If you select either WEP or WPA-PSK security (recommended), then follow the directions to enter the appropriate key. Click Next to continue and Apply to save your wireless LAN settings. 4 Check your configuration and write down your wireless LAN settings for later use. Click Finish to complete and save the wizard setup. 5 Your Internet i s ready for you to use. Open your browser and navigate to your favorite website. 4 Internet Connection Setup Using Advanced Settings Use this section to set up your Internet connection manually if you do not PK5001Z Quick Start Guide 6 see the ISP Parameters for Internet Access screen when you run the wizard (see section 4, step 4). 1 Login again. (Follow steps 1 to 5 in section 3.) 2 Select Go to Advanced setup. Then, click Apply. 3 The Status screen appears. Click Network > WAN i n the navigation panel on the left of the screen. 4 E n t e r the information exactly as provided by your ISP. Click Apply. 5 If you still cannot access the Internet, see Troubleshooting and/or contact your Internet Service Provider (ISP) for assistance. Troubleshooting 1 If you cannot access the web configurator, • Your computer may be set to use a static IP address in a different subnet from the ZyXEL device. See the appendix in the User’s Guide for information on setting up your IP address. • If you are using Internet Explorer in Windows XP or Windows Server 2003, make sure you allow pop-up windows, JavaScripts and Java permissions or set the Internet security level lower than High in Internet Explorer (i n Internet Explorer, click Tools > Internet Options > Security > Custom Level...). See the appendix i n the User’s Guide for more information. PK5001Z Quick Start Guide 7 2 If you cannot access the Internet when your computer i s connected to the ETHERNET port, follow these steps. A) Check the lights on the front panel . If they are different from what i s described in section 1, make sure the PK5001Z is correctly connected. (See section 1.) If the lights are still different, turn off the device, wait a few seconds, and turn it on again. B) Check you have correctly entered the information your ISP gave you. For example, if your account has a user name and password, make sure you type i t correctly. In addition, if you are not sure which encapsulation your ISP uses, contact your ISP. If your ISP did not give you Internet connection information, follow the steps in section 2. C) If you are using a new Internet account, contact your ISP to make sure it is active. D) If you still have problems, see Troubleshooting i n the User’s Guide. If you cannot access the Internet after you take the steps above, either try the following or contact you…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 ZyXEL Communications Corporation 2012/02/03 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, ZyXEL Communications Corporation hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Equipment: 802.11n Wireless ADSL2+ 4-port Gateway Model No.: PK5001Z ; PK5001Z for CenturyLink ; DSL-100HN-L1 for CenturyLink ; DSL-100HN-L1 FCC ID: I88PK5001Z We affirm that between SIEMIC and ZyXEL Communications Corporation, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Thomas Wei/ Senior Manager ZyXEL Communications Corporation/ NO.6,Innovation Rd.II Science Based Industrial Park Hsin-Chu,Taiwan

Attestation for FCC Declaration of Conformity FCC ID: I88PK5001Z Date: Feb 03, 2012 Please be notified that we, the undersigned, Cerpass technology Coporation declares that the product which bears the above FCC ID is a;so compliant with the FCC requirements for DOC. The test report number supporting the DOC is SEFD1201035. Testing in regards to this report was done by Cerpass technology Coporation, located at No.68-1, Shihbachongsi, Shihding Township, Taipei City 223, Taiwan, R.O.C., which has been accredited in accordance to all of the requirements of 47 CFR 2.948(d) and(e)of the FCC rules and KDB349827. Sincerely, Thomas Wei/ Senior Manager ZyXEL Communications Corporation/ NO.6,Innovation Rd.II Science Based Industrial Park Hsin-Chu,Taiwan

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 1.0 2.0 August – 11 - 2008 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 2.0 ZyXEL Communications Corporation 2012/02/03 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: I88PK5001Z We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics - Operational Description - Block Diagram - Part List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Thomas Wei/ Senior Manager ZyXEL Communications Corporation/ NO.6,Innovation Rd.II Science Based Industrial Park Hsin-Chu,Taiwan

CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 1 of 5 EXTERNAL PHOTOGRAPHS OF EUT 1) EUT Photo 2) EUT Photo CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 2 of 5 3) EUT Photo 4) EUT Photo CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 3 of 5 5) EUT Photo Adapter 6) EUT Photo CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 4 of 5 7) EUT Photo(power adapter) 8) EUT Photo(power adapter) CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 5 of 5 9) EUT Photo(power adapter)

802.11n Wireless ADSL2+ 4-port Gateway (Model name: PK5001Z ; PK5001Z for CenturyLink ; DSL-100HN-L1 for CenturyLink ; DSL-100HN-L1) FCC ID Position: FCC ID

CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 1 of 3 INTERNAL PHOTOGRAPHS OF EUT 1) EUT Photo 2) EUT Photo CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 2 of 3 3) EUT Photo 4) EUT Photo Chain 0 Chain 1 CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 3 of 3 5) EUT Photo（module）

CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Jan 31,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 1 of 3 Radio frequency exposure LIMIT According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter. EUT Specification EUT 802.11n Wireless ADSL2+ 4-port Gateway Frequency band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.725GHz ~ 5.850GHz Bluetooth: 2.402GHz ~ 2.480 GHz Device category Portable (<20cm separation) Mobile (>20cm separation) Exposure classification Occupational/Controlled exposure (S = 5mW/cm 2 ) General Population/Uncontrolled exposure (S=1mW/cm 2 ) Antenna diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Max. output power 802.11b: 21.85 dBm (153.11 mW) 802.11g: 21.04dBm (127.06 mW) 802.11n (20MHz): Chain0:21.37dBm (137.09 mW) Chain1:21.62 dBm (145.21 mW) 802.11n (40MHz): Chain0:21.17 dBm (130.92 mW) Chain1:22.27 dBm (168.66 mW) Antenna gain (Max) Chain0:5.00 dBi (Numeric gain:3.162 ) Chain1:5.00 dBi(Numeric gain: 3.162) Evaluation applied MPE Evaluation* SAR Evaluation N/A Remark: 1. The maximum output power is 22.27 dBm (168.66 mW) at 2422 MHz (withnumeric 3.162 antenna gain.) 2. DTS device is not subject to routine RF evaluation; MPE estimate is used to justify the compliance. 3. For mobile or fixed location transmitters, no SAR consideration applied. The maximum power density is 1.0 mW/cm 2 even if the calculation indicates that the power density would be larger. CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Jan 31,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 2 of 3 TEST RESULTS No non-compliance noted. Calculation Given d GP E ×× = 30 & 3770 2 E S= Where E = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / square centimeter Combining equations and re-arranging the terms to express the distance as a function of the remaining variables yields: 2 3770 30 d GP S ×× = Changing to units of mW and cm, using: P (mW) = P (W) / 1000 and d (cm) = d(m) / 100 Yields () () 2 2 0796.0 100/3770 1000/30 d GP d GP S × ×= × ×× = Equation 1 Where d = Distance in cm P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Jan 31,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 3 of 3 Maximum Permissible Exposure Modulation Mode Frequency band (MHz) Max. Conducted output power(dBm) Antenna gain (dBi) Distance (cm) Power density (mW/cm2) Limit (mW/cm2) 802.11b 2412-2462 21.85 5.00 20 0.096 1 802.11g 2412-2462 21.04 5.00 20 0.080 1 802.11n(20MHz)(Chain0) 2412-2462 21.37 5.00 20 0.086 1 802.11n(20MHz)(Chain1) 2412-2462 21.62 5.00 20 0.091 1 802.11 n(20MHz) (Chain0+Chain1) 2412-2462 / / 20 0.177 1 802.11n(40MHz)(Chain0) 2422-2452 21.17 5.00 20 0.082 1 802.11n(40MHz)(Chain1) 2422-2452 22.27 5.00 20 0.106 1 802.11 n(40MHz) (Chain0+Chain1) 2422-2452 / / 20 0.188 1 NOTE: Total(Chain0+Chain1) , the formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density

CERPASS TECHNOLOGY (SUZHOU)CO., LTD Report No.: SEFI1201035 Cerpass Technology(Suzhou) Co., Ltd. Issued Date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 1 of 78 FCC ID : I88PK5001Z FCC TEST REPORT According to FCC Rules and Regulations Part 15 Subpart C Applicant : ZyXEL Communications Corporation Address : NO.6,Innovation Rd.II Science Based Industrial Park Hsin-Chu,Taiwan Equipment : 802.11n Wireless ADSL2+ 4-port Gateway Model No. : PK5001Z ; PK5001Z for CenturyLink ; DSL-100HN-L1 for CenturyLink ; DSL-100HN-L1 FCC ID : I88PK5001Z Trade Name : ‚ The test result refers exclusively to the test presented test model / sample., ‚ Without written approval of Cerpass Technology(Suzhou) Corp. the test report shall not be reproduced except in full. ‚ The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. ‚ The test report must not be used by the clients to claim product certification approval by NVLAP or any agency of the Government. CERPASS TECHNOLOGY (SUZHOU)CO., LTD Report No.: SEFI1201035 Cerpass Technology(Suzhou) Co., Ltd. Issued Date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 2 of 78 FCC ID : I88PK5001Z Contents 1. Report of Measurements and Examinations .................................................................................... 6 1.1 List of Measurements and Examinations ................................................................................... 6 2. Test Configuration of Equipment under Test ................................................................................... 7 2.1 Manufacturer .............................................................................................................................. 7 2.2 Feature of Equipment under Test............................................................................................... 7 2.3 Carrier Frequency of Channels ..................................................................................................8 2.4 Test Mode and Test Software.....................................................................................................9 2.5 Description of Test System......................................................................................................... 9 2.6 General Information of Test......................................................................................................10 2.7 Measurement Uncertainty ........................................................................................................10 3. Antenna Requirements..................................................................................................................... 11 3.1 Standard Applicable ................................................................................................................. 11 3.2 Antenna Construction and Directional Gain............................................................................. 11 4. Test of Conducted Emission............................................................................................................12 4.1 Test Limit .................................................................................................................................. 12 4.2 Test Procedures .......................................................................................................................12 4.3 Typical Test Setup ....................................................................................................................13 4.4 Measurement equipment ......................................................................................................... 13 4.5 Test Result and Data................................................................................................................14 5. Test of Radiated Emission ...............................................................................................................16 5.1 Test Limit .................................................................................................................................. 16 5.2 Test Procedures .......................................................................................................................16 5.3 Typical Test Setup ....................................................................................................................17 5.4 Measurement equipment ......................................................................................................... 17 5.5 Test Result and Data................................................................................................................18 6. 6dB Bandwidth Measurement Data .................................................................................................31 6.1 Test Limit .................................................................................................................................. 31 6.2 Test Procedures .......................................................................................................................31 6.3 Test Setup Layout ....................................................................................................................31 6.4 Measurement equipment ......................................................................................................... 31 6.5 Test Result and Data................................................................................................................31 7. Maximum Peak Output Power .........................................................................................................41 7.1 Test Limit .................................................................................................................................. 41 7.2 Test Procedures ..........…

Text truncated - open the document above for the full version.

CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 1 of 3 TEST SETUP PHOTOGRAPHS OF EUT AC POWER LINE CONDUCTED EMISSION TEST CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 2 of 3 RADEATED EMISSION TEST Below 1G CERPASS TECHNOLOGY CORP. Report No.: SEFI1201035 Cerpass Technology Corp. Issued date : Feb 1,2012 Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 3 of 3 Above 1G